EXYNOS5420: Add SMDK5420 board support
Subsystems (2)
v8 cover EXYNOS5420: Add SMDK5420 board support
This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.
Changes in V2:
- Corrected a compilation issue for SMDK5420.
Changes in V3:
- Add patch to support variable size SPL support
- Add patch to disable SMU for eMMC.
Changes in V4:
- Added check for MAX77686 pmic compilation.
- Added correct calculation of gpio based addresses.
- Rebased on the latest u-boot code.
- Removed patches for UART and TZPC changes as they were not needed.
- Added flag to disable SMU for eMMC.
Changes in V5:
- Moved functions board_mmc_init and board_eth_init to common/board.c in case of device tree support.
Changes in V6:
- Rebased on the latest mainline branch.
- Moved the definitions for SMU to arch/arm dwmmc.h
Changes in V7:
- Removed below patch as it is already merged "DWMMC: SMDK5420: Disable SMU for eMMC"
- Corrected the multi line comments and removal of blank spaces and lines.
- Corrected the license.
Changes in V8:
- corrected the if loops with if conditions of pro_id and cpu_id.
Rajeshwari S Shinde (9):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL support
arch/arm/cpu/armv7/exynos/clock.c | 258 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 10 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 421 +++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 738 +++++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 260 ++++++++- arch/arm/dts/exynos5.dtsi | 198 +++++++ arch/arm/dts/exynos5250.dtsi | 196 +------ arch/arm/dts/exynos5420.dtsi | 70 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 51 +- arch/arm/include/asm/arch-exynos/dmc.h | 123 +++-- arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++- arch/arm/include/asm/arch-exynos/periph.h | 3 + board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 407 ++++++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 ++++++ board/samsung/smdk5250/exynos5-dt.c | 361 +----------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 34 ++ board/samsung/smdk5420/smdk5420.c | 159 ++++++ board/samsung/smdk5420/smdk5420_spl.c | 52 ++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5-dt.h | 300 ++++++++++ include/configs/exynos5250-dt.h | 316 +---------- include/configs/smdk5420.h | 56 ++ spl/Makefile | 7 +- tools/Makefile | 3 +- tools/mkexynosspl.c | 167 ++++-- 33 files changed, 4227 insertions(+), 1344 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h
Signature · 1 line
1.7.12.4
PATCH v8 1/9 EXYNOS5: Create a common board file
Create a common board.c file for all functions which are common across all EXYNOS5 platforms.
exynos_init function is provided for platform specific code.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added check for the compilation of MAX77686 pmic.
Changes in V5:
- Moved board_eth_init and board_mmc_init in case of device tree support
Changes in V6:
- None.
Changes in V7:
- None
Changes in V8:
- None
arch/arm/include/asm/arch-exynos/board.h | 17 ++ board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 405 +++++++++++++++++++++++++++++++ board/samsung/smdk5250/exynos5-dt.c | 361 +-------------------------- board/samsung/smdk5250/smdk5250.c | 182 +------------- include/configs/exynos5250-dt.h | 2 + 6 files changed, 435 insertions(+), 536 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c
arch/arm/include/asm/arch-exynos/board.h new file +17 -0
@@ -0,0 +1,17 @@ +/* +* (C) Copyright 2013 Samsung Electronics +* Rajeshwari Shinde <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef _EXYNOS_BOARD_H +#define _EXYNOS_BOARD_H + +/* +* Exynos baord specific changes for +* board_init +*/ +int exynos_init (void ); + +#endif /* EXYNOS_BOARD_H */
board/samsung/common/Makefile +4 -0
@@ -11,6 +11,10 @@ LIB = $(obj)libsamsung.o COBJS-$(CONFIG_SOFT_I2C_MULTI_BUS) += multi_i2c.o +ifeq ($(CONFIG_SPL_BUILD),) +COBJS-$(CONFIG_BOARD_COMMON) += board.o +endif + SRCS := $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y))
board/samsung/common/board.c new file +405 -0
405 lines not on this page · raw message
board/samsung/smdk5250/exynos5-dt.c +4 -357
411 lines not on this page · raw message
board/samsung/smdk5250/smdk5250.c +3 -179
219 lines not on this page · raw message
include/configs/exynos5250-dt.h +2 -0
@@ -21,6 +21,8 @@#define CONFIG_ARCH_CPU_INIT #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_COMMON +#define CONFIG_ARCH_EARLY_INIT_R /* Enable fdt support for Exynos5250 */ #define CONFIG_OF_CONTROL
Signature · 1 line
1.7.12.4
PATCH v8 2/9 Exynos5420: Add base addresses for 5420
In reply to Rajeshwari S ShindeAdds base addresses of various IPs and controllers required for Exynos5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added base address for TZPC.
Changes in V5:
- None
Chnages in V6:
- Rebased on latest samsung mainline branch.
Changes in V7:
- Corrected the comments
Changes in V8:
- None
arch/arm/include/asm/arch-exynos/cpu.h | 47 +++++++++++++++++++++++++++++++++- 1 file changed, 46 insertions(+), 1 deletion(-)
arch/arm/include/asm/arch-exynos/cpu.h +46 -1
@@ -88,7 +88,7 @@#define EXYNOS4X12_DMC_PHY_BASE DEVICE_NOT_AVAILABLE#define EXYNOS4X12_AUDIOSS_BASE DEVICE_NOT_AVAILABLE -/* EXYNOS5 Common*/ +/* EXYNOS5 */ #define EXYNOS5_I2C_SPACING 0x10000#define EXYNOS5_AUDIOSS_BASE 0x03810000
@@ -124,6 +124,44 @@#define EXYNOS5_ADC_BASE DEVICE_NOT_AVAILABLE#define EXYNOS5_MODEM_BASE DEVICE_NOT_AVAILABLE +/* EXYNOS5420 */ +#define EXYNOS5420_AUDIOSS_BASE 0x03810000 +#define EXYNOS5420_GPIO_PART5_BASE 0x03860000 +#define EXYNOS5420_PRO_ID 0x10000000 +#define EXYNOS5420_CLOCK_BASE 0x10010000 +#define EXYNOS5420_POWER_BASE 0x10040000 +#define EXYNOS5420_SWRESET 0x10040400 +#define EXYNOS5420_SYSREG_BASE 0x10050000 +#define EXYNOS5420_TZPC_BASE 0x100E0000 +#define EXYNOS5420_WATCHDOG_BASE 0x101D0000 +#define EXYNOS5420_ACE_SFR_BASE 0x10830000 +#define EXYNOS5420_DMC_PHY_BASE 0x10C00000 +#define EXYNOS5420_DMC_CTRL_BASE 0x10C20000 +#define EXYNOS5420_DMC_TZASC0_BASE 0x10D40000 +#define EXYNOS5420_DMC_TZASC1_BASE 0x10D50000 +#define EXYNOS5420_USB_HOST_EHCI_BASE 0x12110000 +#define EXYNOS5420_MMC_BASE 0x12200000 +#define EXYNOS5420_SROMC_BASE 0x12250000 +#define EXYNOS5420_UART_BASE 0x12C00000 +#define EXYNOS5420_I2C_BASE 0x12C60000 +#define EXYNOS5420_I2C_8910_BASE 0x12E00000 +#define EXYNOS5420_SPI_BASE 0x12D20000 +#define EXYNOS5420_I2S_BASE 0x12D60000 +#define EXYNOS5420_PWMTIMER_BASE 0x12DD0000 +#define EXYNOS5420_SPI_ISP_BASE 0x131A0000 +#define EXYNOS5420_GPIO_PART2_BASE 0x13400000 +#define EXYNOS5420_GPIO_PART3_BASE 0x13410000 +#define EXYNOS5420_GPIO_PART4_BASE 0x14000000 +#define EXYNOS5420_GPIO_PART1_BASE 0x14010000 +#define EXYNOS5420_MIPI_DSIM_BASE 0x14500000 +#define EXYNOS5420_DP_BASE 0x145B0000 + +#define EXYNOS5420_USBPHY_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_USBOTG_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_FIMD_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_ADC_BASE DEVICE_NOT_AVAILABLE +#define EXYNOS5420_MODEM_BASE DEVICE_NOT_AVAILABLE +#ifndef __ASSEMBLY__#include <asm/io.h> /* CPU detection macros */
@@ -157,6 +195,10 @@ static inline void s5p_set_cpu_id(void)/* Exynos5250 */ s5p_cpu_id =0x5250 ;break ; +case 0x420 : +/* Exynos5420 */ + s5p_cpu_id =0x5420 ; +break ; } }
@@ -184,6 +226,7 @@ static inline int __attribute__((no_instrument_function)) \ IS_EXYNOS_TYPE(exynos4210, 0x4210) IS_EXYNOS_TYPE(exynos4412, 0x4412) IS_EXYNOS_TYPE(exynos5250, 0x5250) +IS_EXYNOS_TYPE(exynos5420, 0x5420)#define SAMSUNG_BASE (device, base) \ static inline unsigned int __attribute__((no_instrument_function)) \
@@ -194,6 +237,8 @@ static inline unsigned int __attribute__((no_instrument_function)) \ return EXYNOS4X12_##base; \ return EXYNOS4_##base; \ } else if (cpu_is_exynos5()) { \ + if (proid_is_exynos5420()) \ + return EXYNOS5420_##base; \ return EXYNOS5_##base; \ } \ return 0; \
Signature · 1 line
1.7.12.4
PATCH v8 3/9 Exynos5420: Add clock initialization for 5420
In reply to Rajeshwari S ShindeThis patch adds code for clock initialization and clock settings of various IP's and controllers, required for Exynos5420
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Corrected the multiline commenting style
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Correct the logic for exynos5420_set_spi_clk api.
Changes in V8:
- Chnages the if condition loop for pro_id and cpu_id.
arch/arm/cpu/armv7/exynos/clock.c | 258 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 738 +++++++++++++++++++------ arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ 6 files changed, 1659 insertions(+), 201 deletions(-)
arch/arm/cpu/armv7/exynos/clock.c +244 -14
@@ -96,7 +96,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k) freq =CONFIG_SYS_CLK_FREQ ; -if (pllreg ==EPLL ) { +if (pllreg ==EPLL || pllreg ==RPLL ) { k = k &0xffff ;/* FOUT = (MDIV + K / 65536) * FIN / (PDIV * 2^SDIV) */ fout = (m + k /PLL_DIV_65536 ) * (freq / (p * (1 << s)));
@@ -117,7 +117,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k) div =PLL_DIV_1024 ; else if (proid_is_exynos4412()) div =PLL_DIV_65535 ; - else if (proid_is_exynos5250()) + else if (proid_is_exynos5250() || proid_is_exynos5420()) div =PLL_DIV_65536 ; else return 0;
@@ -362,6 +362,43 @@ unsigned long clock_get_periph_rate(int peripheral)return 0 ; } +/* exynos5420: return pll clock frequency */ +static unsigned long exynos5420_get_pll_clk (int pllreg) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long r, k =0 ; + +switch (pllreg) { +case APLL : + r =readl (&clk->apll_con0); +break ; +case MPLL : + r =readl (&clk->mpll_con0); +break ; +case EPLL : + r =readl (&clk->epll_con0); + k =readl (&clk->epll_con1); +break ; +case VPLL : + r =readl (&clk->vpll_con0); + k =readl (&clk->vpll_con1); +break ; +case BPLL : + r =readl (&clk->bpll_con0); +break ; +case RPLL : + r =readl (&clk->rpll_con0); + k =readl (&clk->rpll_con1); +break ; +default : +printf ("Unsupported PLL (%d)\n" , pllreg); +return 0 ; + } + +return exynos_get_pll_clk (pllreg, r, k); +} +/* exynos4: return ARM clock frequency */ static unsigned long exynos4_get_arm_clk (void ) {
@@ -485,6 +522,27 @@ static unsigned long exynos4x12_get_pwm_clk(void)return pclk; } +/* exynos5420: return pwm clock frequency */ +static unsigned long exynos5420_get_pwm_clk (void ) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long pclk, sclk; +unsigned int ratio; + +/* +* CLK_DIV_PERIC3 +* PWM_RATIO [3:0] +*/ + ratio =readl (&clk->div_peric0); + ratio = (ratio >>28 ) &0xf ; + sclk =get_pll_clk (MPLL ); + + pclk = sclk / (ratio +1 ); + +return pclk; +} +/* exynos4: return uart clock frequency */ static unsigned long exynos4_get_uart_clk (int dev_index) {
@@ -624,6 +682,53 @@ static unsigned long exynos5_get_uart_clk(int dev_index)return uclk; } +/* exynos5420: return uart clock frequency */ +static unsigned long exynos5420_get_uart_clk (int dev_index) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long uclk, sclk; +unsigned int sel; +unsigned int ratio; + +/* +* CLK_SRC_PERIC0 +* UART0_SEL [3:0] +* UART1_SEL [7:4] +* UART2_SEL [8:11] +* UART3_SEL [12:15] +* UART4_SEL [16:19] +* UART5_SEL [23:20] +*/ + sel =readl (&clk->src_peric0); + sel = (sel >> ((dev_index *4 ) +4 )) &0x7 ; + +if (sel ==0x3 ) + sclk =get_pll_clk (MPLL ); +else if (sel ==0x6 ) + sclk =get_pll_clk (EPLL ); +else if (sel ==0x7 ) + sclk =get_pll_clk (RPLL ); +else +return 0 ; + +/* +* CLK_DIV_PERIC0 +* UART0_RATIO [3:0] +* UART1_RATIO [7:4] +* UART2_RATIO [8:11] +* UART3_RATIO [12:15] +* UART4_RATIO [16:19] +* UART5_RATIO [23:20] +*/ + ratio =readl (&clk->div_peric0); + ratio = (ratio >> ((dev_index *4 ) +8 )) &0xf ; + + uclk = sclk / (ratio +1 ); + +return uclk; +} +static unsigned long exynos4_get_mmc_clk (int dev_index) { struct exynos4_clock *clk =
@@ -718,6 +823,34 @@ static unsigned long exynos5_get_mmc_clk(int dev_index)return uclk; } +static unsigned long exynos5420_get_mmc_clk (int dev_index) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned long uclk, sclk; +unsigned int sel, ratio; +int shift =0 ; + + sel =readl (&clk->src_fsys); + sel = (sel >> ((dev_index *4 ) +8 )) &0x7 ; + +if (sel ==0x3 ) + sclk =get_pll_clk (MPLL ); +else if (sel ==0x6 ) + sclk =get_pll_clk (EPLL ); +else +return 0 ; + + ratio =readl (&clk->div_fsys1); + + shift = dev_index *10 ; + + ratio = (ratio >> shift) &0x3ff ; + uclk = (sclk / (ratio +1 )); + +return uclk; +} +/* exynos4: set the mmc clock */ static void exynos4_set_mmc_clk (int dev_index,unsigned int div) {
@@ -804,6 +937,23 @@ static void exynos5_set_mmc_clk(int dev_index, unsigned int div)writel (val, addr); } +/* exynos5: set the mmc clock */ +static void exynos5420_set_mmc_clk (int dev_index,unsigned int div) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +unsigned int addr; +unsigned int val, shift; + + addr = (unsigned int )&clk->div_fsys1; + shift = dev_index *10 ; + + val =readl (addr); + val &= ~(0x3ff << shift); + val |= (div &0x3ff ) << shift; +writel (val, addr); +} +/* get_lcd_clk: return lcd clock frequency */ static unsigned long exynos4_get_lcd_clk (void ) {
@@ -1324,6 +1474,72 @@ static int exynos5_set_spi_clk(enum periph_id periph_id,return 0 ; } +static int exynos5420_set_spi_clk (enum periph_id periph_id, +unsigned int rate) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)samsung_get_base_clock (); +int main; +unsigned int fine; +unsigned shift, pre_shift; +unsigned div_mask =0xf , pre_div_mask =0xff ; +u32 *reg; +u32 *pre_reg; + + + main =clock_calc_best_scalar (4 ,8 ,400000000 , rate, &fine); +if (main <0 ) { +debug ("%s: Cannot set clock rate for periph %d" , + __func__, periph_id); +return -1 ; + } + main = main -1 ; + fine = fine -1 ; + +switch (periph_id) { +case PERIPH_ID_SPI0 : + reg = &clk->div_peric1; + shift =20 ; + pre_reg = &clk->div_peric4; + pre_shift =8 ; +break ; +case PERIPH_ID_SPI1 : + reg = &clk->div_peric1; + shift =24 ; + pre_reg = &clk->div_peric4; + pre_shift =16 ; +break ; +case PERIPH_ID_SPI2 : + reg = &clk->div_peric1; + shift =28 ; + pre_reg = &clk->div_peric4; + pre_shift =24 ; +break ; +case PERIPH_ID_SPI3 : + reg = &clk->div_isp1; + shift =16 ; + pre_reg = &clk->div_isp1; + pre_shift =0 ; +break ; +case PERIPH_ID_SPI4 : + reg = &clk->div_isp1; + shift =20 ; + pre_reg = &clk->div_isp1; + pre_shift =8 ; +break ; +default : +debug ("%s: Unsupported peripheral ID %d\n" , __func__, + periph_id); +return -1 ; + } + +clrsetbits_le32 (reg, div_mask << shift, (main & div_mask) << shift); +clrsetbits_le32 (pre_reg, pre_div_mask << pre_shift, + (fine & pre_div_mask) << pre_shift); + +return 0 ; +} +static unsigned long exynos4_get_i2c_clk (void ) { struct exynos4_clock *clk =
@@ -1341,9 +1557,11 @@ static unsigned long exynos4_get_i2c_clk(void)unsigned long get_pll_clk (int pllreg) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_pll_clk (pllreg);return exynos5_get_pll_clk (pllreg); -else { + }else {if (proid_is_exynos4412 ())return exynos4x12_get_pll_clk (pllreg);return exynos4_get_pll_clk (pllreg);
@@ -1375,9 +1593,11 @@ unsigned long get_i2c_clk(void)unsigned long get_pwm_clk (void ) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_pwm_clk ();return clock_get_periph_rate (PERIPH_ID_PWM0 ); -else { + }else {if (proid_is_exynos4412 ())return exynos4x12_get_pwm_clk ();return exynos4_get_pwm_clk ();
@@ -1386,9 +1606,11 @@ unsigned long get_pwm_clk(void)unsigned long get_uart_clk (int dev_index) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_uart_clk (dev_index);return exynos5_get_uart_clk (dev_index); -else { + }else {if (proid_is_exynos4412 ())return exynos4x12_get_uart_clk (dev_index);return exynos4_get_uart_clk (dev_index);
@@ -1397,17 +1619,22 @@ unsigned long get_uart_clk(int dev_index)unsigned long get_mmc_clk (int dev_index) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_get_mmc_clk (dev_index);return exynos5_get_mmc_clk (dev_index); -else + }else {return exynos4_get_mmc_clk (dev_index); + } }void set_mmc_clk (int dev_index,unsigned int div) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_set_mmc_clk (dev_index, div);exynos5_set_mmc_clk (dev_index, div); -else { + }else {if (proid_is_exynos4412 ())exynos4x12_set_mmc_clk (dev_index, div);exynos4_set_mmc_clk (dev_index, div);
@@ -1438,10 +1665,13 @@ void set_mipi_clk(void)int set_spi_clk (int periph_id,unsigned int rate) { -if (cpu_is_exynos5 ()) +if (cpu_is_exynos5 ()) { +if (proid_is_exynos5420 ()) +return exynos5420_set_spi_clk (periph_id, rate);return exynos5_set_spi_clk (periph_id, rate); -else + }else {return 0 ; + } } int set_i2s_clk_prescaler(unsigned int src_frq, unsigned int dst_frq,
arch/arm/cpu/armv7/exynos/clock_init.h +17 -0
@@ -10,7 +10,11 @@#define __EXYNOS_CLOCK_INIT_Henum { +#ifdef CONFIG_EXYNOS5420 +MEM_TIMINGS_MSR_COUNT =5 , +#else MEM_TIMINGS_MSR_COUNT =4 , +#endif };/* These are the ratio's for configuring ARM clock */
@@ -59,6 +63,18 @@ struct mem_timings {unsigned bpll_mdiv;unsigned bpll_pdiv;unsigned bpll_sdiv; +unsigned kpll_mdiv; +unsigned kpll_pdiv; +unsigned kpll_sdiv; +unsigned dpll_mdiv; +unsigned dpll_pdiv; +unsigned dpll_sdiv; +unsigned ipll_mdiv; +unsigned ipll_pdiv; +unsigned ipll_sdiv; +unsigned spll_mdiv; +unsigned spll_pdiv; +unsigned spll_sdiv;unsigned pclk_cdrex_ratio;unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT ];
@@ -115,6 +131,7 @@ struct mem_timings {uint8_t send_zq_init;/* 1 to send this command */ unsigned impedance;/* drive strength impedeance */ uint8_t gate_leveling_enable;/* check gate leveling is enabled */ +uint8_t read_leveling_enable;/* check h/w read leveling is enabled */ };/**
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +338 -14
390 lines not on this page · raw message
arch/arm/cpu/armv7/exynos/exynos5_setup.h +565 -173
854 lines not on this page · raw message
arch/arm/include/asm/arch-exynos/clk.h +1 -0
@@ -14,6 +14,7 @@#define HPLL 3#define VPLL 4#define BPLL 5 +#define RPLL 6enum pll_src_bit {EXYNOS_SRC_MPLL =6 ,
arch/arm/include/asm/arch-exynos/clock.h +494 -0
500 lines not on this page · raw message
Signature · 1 line
1.7.12.4
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v8 3/9 Exynos5420: Add clock initialization for 5420
ping.
-------- Original Message --------
Subject: Re: [PATCH 3/9 v8] Exynos5420: Add clock initialization for 5420
Date: Thu, 21 Nov 2013 16:03:23 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com
Dear Rajeshwari,
Quoted 237 lines · Rajeshwari S Shinde
This patch adds code for clock initialization and clock settings of various IP's and controllers, required for Exynos5420
Signed-off-by Rajeshwari S Shinde <[email protected]>Signed-off-by Akshay Saraswat <[email protected]>Acked-by Simon Glass <[email protected]>---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Corrected the multiline commenting style
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Correct the logic forexynos5420_set_spi_clkapi.
Changes in V8:
- Chnages the if condition loop forpro_idandcpu_id.arch/arm/cpu/armv7/exynos/clock.c | 258 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 738 +++++++++++++++++++------ arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ 6 files changed, 1659 insertions(+), 201 deletions(-)arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +152
-14@@ -24,6 +24,24 @@DECLARE_GLOBAL_DATA_PTR ; struct arm_clk_ratios arm_clk_ratios[] = { +#ifdef CONFIG_EXYNOS5420 + { + .arm_freq_mhz = 900, + + .apll_mdiv = 0x96, + .apll_pdiv = 0x2, + .apll_sdiv = 0x1, + + .arm2_ratio = 0x0, + .apll_ratio = 0x3, + .pclk_dbg_ratio = 0x6, + .atb_ratio = 0x6, + .periph_ratio = 0x7, + .acp_ratio = 0x0, + .cpud_ratio = 0x2, + .arm_ratio = 0x0, + } +#else { .arm_freq_mhz = 600,@@ -115,8 +133,133 @@ struct arm_clk_ratios arm_clk_ratios[] = { .cpud_ratio = 0x3, .arm_ratio = 0x0, } +#endif }; + struct mem_timings mem_timings[] = { +#ifdef CONFIG_EXYNOS5420 + { + .mem_manuf = MEM_MANUF_SAMSUNG, + .mem_type = DDR_MODE_DDR3, + .frequency_mhz = 800, + +/* MPLL @800MHz*/ + .mpll_mdiv = 0xc8, + .mpll_pdiv = 0x3, + .mpll_sdiv = 0x1, +/* CPLL @666MHz */ + .cpll_mdiv = 0xde, + .cpll_pdiv = 0x4, + .cpll_sdiv = 0x1, +/* EPLL @600MHz */ + .epll_mdiv = 0x64, + .epll_pdiv = 0x2, + .epll_sdiv = 0x1, +/* VPLL @430MHz */ + .vpll_mdiv = 0xd7, + .vpll_pdiv = 0x3, + .vpll_sdiv = 0x2, +/* BPLL @800MHz */ + .bpll_mdiv = 0xc8, + .bpll_pdiv = 0x3, + .bpll_sdiv = 0x1, +/* KPLL @600MHz */ + .kpll_mdiv = 0x190, + .kpll_pdiv = 0x4, + .kpll_sdiv = 0x2, +/* DPLL @600MHz */ + .dpll_mdiv = 0x190, + .dpll_pdiv = 0x4, + .dpll_sdiv = 0x2, +/* IPLL @370MHz */ + .ipll_mdiv = 0xb9, + .ipll_pdiv = 0x3, + .ipll_sdiv = 0x2, +/* SPLL @400MHz */ + .spll_mdiv = 0xc8, + .spll_pdiv = 0x3, + .spll_sdiv = 0x2, + + .direct_cmd_msr = { +0x00020018 ,0x00030000 ,0x00010046 ,0x00000d70 , +0x00000c70 + }, + .timing_ref = 0x000000bb, + .timing_row = 0x6836650f, + .timing_data = 0x3630580b, + .timing_power = 0x41000a26, + .phy0_dqs = 0x08080808, + .phy1_dqs = 0x08080808, + .phy0_dq = 0x08080808, + .phy1_dq = 0x08080808, + .phy0_tFS = 0x8, + .phy1_tFS = 0x8, + .phy0_pulld_dqs = 0xf, + .phy1_pulld_dqs = 0xf, + + .lpddr3_ctrl_phy_reset = 0x1, + .ctrl_start_point = 0x10, + .ctrl_inc = 0x10, + .ctrl_start = 0x1, + .ctrl_dll_on = 0x1, + .ctrl_ref = 0x8, + + .ctrl_force = 0x1a, + .ctrl_rdlat = 0x0b, + .ctrl_bstlen = 0x08, + + .fp_resync = 0x8, + .iv_size = 0x7, + .dfi_init_start = 1, + .aref_en = 1, + + .rd_fetch = 0x3, + + .zq_mode_dds = 0x7, + .zq_mode_term = 0x1, + .zq_mode_noterm = 1, + +/* +* Dynamic Clock: Always Running +* Memory Burst length: 8 +* Number of chips: 1 +* Memory Bus width: 32 bit +* Memory Type: DDR3 +* Additional Latancy for PLL: 0 Cycle +*/ + .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE | +DMC_MEMCONTROL_DPWRDN_DISABLE | +DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE | +DMC_MEMCONTROL_TP_DISABLE | +DMC_MEMCONTROL_DSREF_DISABLE | +DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE (0 ) | +DMC_MEMCONTROL_MEM_TYPE_DDR3 | +DMC_MEMCONTROL_MEM_WIDTH_32BIT | +DMC_MEMCONTROL_NUM_CHIP_1 | +DMC_MEMCONTROL_BL_8 | +DMC_MEMCONTROL_PZQ_DISABLE | +DMC_MEMCONTROL_MRR_BYTE_7_0 , + .memconfig = DMC_MEMCONFIG_CHIP_MAP_SPLIT | +DMC_MEMCONFIGX_CHIP_COL_10 | +DMC_MEMCONFIGX_CHIP_ROW_15 | +DMC_MEMCONFIGX_CHIP_BANK_8 , + .prechconfig_tp_cnt = 0xff, + .dpwrdn_cyc = 0xff, + .dsref_cyc = 0xffff, + .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE | +DMC_CONCONTROL_TIMEOUT_LEVEL0 | +DMC_CONCONTROL_RD_FETCH_DISABLE | +DMC_CONCONTROL_EMPTY_DISABLE | +DMC_CONCONTROL_AREF_EN_DISABLE | +DMC_CONCONTROL_IO_PD_CON_DISABLE , + .dmc_channels = 1, + .chips_per_channel = 1, + .chips_to_configure = 1, + .send_zq_init = 1, + .gate_leveling_enable = 1, + .read_leveling_enable = 0, + } +#else { .mem_manuf =MEM_MANUF_ELPIDA , .mem_type = DDR_MODE_DDR3,@@ -324,6 +467,7 @@ struct mem_timings mem_timings[] = { .impedance = IMP_OUTPUT_DRV_40_OHM, .gate_leveling_enable = 1, } +#endif };/** @@ -399,7 +543,7 @@ struct mem_timings *clock_get_mem_timings(void)return NULL ; } -void system_clock_init () +static void exynos5250_system_clock_init (void ) {struct exynos5_clock *clk = (struct exynos5_clock *)samsung_get_base_clock ();@@ -436,19 +580,13 @@ void system_clock_init() }while ((val |MUX_BPLL_SEL_MASK ) != val);/* PLL locktime */ -writel (APLL_LOCK_VAL , &clk->apll_lock); - -writel (MPLL_LOCK_VAL , &clk->mpll_lock); - -writel (BPLL_LOCK_VAL , &clk->bpll_lock); - -writel (CPLL_LOCK_VAL , &clk->cpll_lock); - -writel (GPLL_LOCK_VAL , &clk->gpll_lock); - -writel (EPLL_LOCK_VAL , &clk->epll_lock); - -writel (VPLL_LOCK_VAL , &clk->vpll_lock); +writel (mem->apll_pdiv *PLL_LOCK_FACTOR , &clk->apll_lock); +writel (mem->mpll_pdiv *PLL_LOCK_FACTOR , &clk->mpll_lock); +writel (mem->bpll_pdiv *PLL_LOCK_FACTOR , &clk->bpll_lock); +writel (mem->cpll_pdiv *PLL_LOCK_FACTOR , &clk->cpll_lock); +writel (mem->gpll_pdiv *PLL_X_LOCK_FACTOR , &clk->gpll_lock); +writel (mem->epll_pdiv *PLL_X_LOCK_FACTOR , &clk->epll_lock); +writel (mem->vpll_pdiv *PLL_X_LOCK_FACTOR , &clk->vpll_lock);writel (CLK_REG_DISABLE , &clk->pll_div2_sel);
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c void system_clock_init() · line 784
Quoted 7 lines
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +4
-0@@ -640,6 +778,192 @@ void system_clock_init()writel (val, &clk->div_fsys2); } +static void exynos5420_system_clock_init (void ) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)EXYNOS5_CLOCK_BASE ;
samsung_get_base_clock();
Quoted 175 lines
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +175
-0+struct mem_timings *mem; +struct arm_clk_ratios *arm_clk_ratio; +u32 val; + + mem =clock_get_mem_timings (); + arm_clk_ratio =get_arm_ratios (); + +/* PLL locktime */ +writel (arm_clk_ratio->apll_pdiv *PLL_LOCK_FACTOR , &clk->apll_lock); +writel (mem->mpll_pdiv *PLL_LOCK_FACTOR , &clk->mpll_lock); +writel (mem->bpll_pdiv *PLL_LOCK_FACTOR , &clk->bpll_lock); +writel (mem->cpll_pdiv *PLL_LOCK_FACTOR , &clk->cpll_lock); +writel (mem->dpll_pdiv *PLL_LOCK_FACTOR , &clk->dpll_lock); +writel (mem->epll_pdiv *PLL_X_LOCK_FACTOR , &clk->epll_lock); +writel (mem->vpll_pdiv *PLL_LOCK_FACTOR , &clk->vpll_lock); +writel (mem->ipll_pdiv *PLL_LOCK_FACTOR , &clk->ipll_lock); +writel (mem->spll_pdiv *PLL_LOCK_FACTOR , &clk->spll_lock); +writel (mem->kpll_pdiv *PLL_LOCK_FACTOR , &clk->kpll_lock); + +setbits_le32 (&clk->src_cpu,MUX_HPM_SEL_MASK ); + +writel (0 , &clk->src_top6); + +writel (0 , &clk->src_cdrex); +writel (SRC_KFC_HPM_SEL , &clk->src_kfc); +writel (HPM_RATIO , &clk->div_cpu1); +writel (CLK_DIV_CPU0_VAL , &clk->div_cpu0); + +/* switch A15 clock source to OSC clock before changing APLL */ +clrbits_le32 (&clk->src_cpu,APLL_FOUT ); + +/* Set APLL */ +writel (APLL_CON1_VAL , &clk->apll_con1); + val =set_pll (arm_clk_ratio->apll_mdiv, + arm_clk_ratio->apll_pdiv, + arm_clk_ratio->apll_sdiv); +writel (val, &clk->apll_con0); +while ((readl (&clk->apll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* now it is safe to switch to APLL */ +setbits_le32 (&clk->src_cpu,APLL_FOUT ); + +writel (SRC_KFC_HPM_SEL , &clk->src_kfc); +writel (CLK_DIV_KFC_VAL , &clk->div_kfc0); + +/* switch A7 clock source to OSC clock before changing KPLL */ +clrbits_le32 (&clk->src_kfc,KPLL_FOUT ); + +/* Set KPLL*/ +writel (KPLL_CON1_VAL , &clk->kpll_con1); + val =set_pll (mem->kpll_mdiv, mem->kpll_pdiv, mem->kpll_sdiv); +writel (val, &clk->kpll_con0); +while ((readl (&clk->kpll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* now it is safe to switch to KPLL */ +setbits_le32 (&clk->src_kfc,KPLL_FOUT ); + +/* Set MPLL */ +writel (MPLL_CON1_VAL , &clk->mpll_con1); + val =set_pll (mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv); +writel (val, &clk->mpll_con0); +while ((readl (&clk->mpll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* Set DPLL */ +writel (DPLL_CON1_VAL , &clk->dpll_con1); + val =set_pll (mem->dpll_mdiv, mem->dpll_pdiv, mem->dpll_sdiv); +writel (val, &clk->dpll_con0); +while ((readl (&clk->dpll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* Set EPLL */ +writel (EPLL_CON2_VAL , &clk->epll_con2); +writel (EPLL_CON1_VAL , &clk->epll_con1); + val =set_pll (mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv); +writel (val, &clk->epll_con0); +while ((readl (&clk->epll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* Set CPLL */ +writel (CPLL_CON1_VAL , &clk->cpll_con1); + val =set_pll (mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv); +writel (val, &clk->cpll_con0); +while ((readl (&clk->cpll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* Set IPLL */ +writel (IPLL_CON1_VAL , &clk->ipll_con1); + val =set_pll (mem->ipll_mdiv, mem->ipll_pdiv, mem->ipll_sdiv); +writel (val, &clk->ipll_con0); +while ((readl (&clk->ipll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* Set VPLL */ +writel (VPLL_CON1_VAL , &clk->vpll_con1); + val =set_pll (mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv); +writel (val, &clk->vpll_con0); +while ((readl (&clk->vpll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* Set BPLL */ +writel (BPLL_CON1_VAL , &clk->bpll_con1); + val =set_pll (mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv); +writel (val, &clk->bpll_con0); +while ((readl (&clk->bpll_con0) &PLL_LOCKED ) ==0 ) + ; + +/* Set SPLL */ +writel (SPLL_CON1_VAL , &clk->spll_con1); + val =set_pll (mem->spll_mdiv, mem->spll_pdiv, mem->spll_sdiv); +writel (val, &clk->spll_con0); +while ((readl (&clk->spll_con0) &PLL_LOCKED ) ==0 ) + ; + +writel (CLK_DIV_CDREX0_VAL , &clk->div_cdrex0); +writel (CLK_DIV_CDREX1_VAL , &clk->div_cdrex1); + +writel (CLK_SRC_TOP0_VAL , &clk->src_top0); +writel (CLK_SRC_TOP1_VAL , &clk->src_top1); +writel (CLK_SRC_TOP2_VAL , &clk->src_top2); +writel (CLK_SRC_TOP7_VAL , &clk->src_top7); + +writel (CLK_DIV_TOP0_VAL , &clk->div_top0); +writel (CLK_DIV_TOP1_VAL , &clk->div_top1); +writel (CLK_DIV_TOP2_VAL , &clk->div_top2); + +writel (0 , &clk->src_top10); +writel (0 , &clk->src_top11); +writel (0 , &clk->src_top12); + +writel (CLK_SRC_TOP3_VAL , &clk->src_top3); +writel (CLK_SRC_TOP4_VAL , &clk->src_top4); +writel (CLK_SRC_TOP5_VAL , &clk->src_top5); + +/* DISP1 BLK CLK SELECTION */ +writel (CLK_SRC_DISP1_0_VAL , &clk->src_disp10); +writel (CLK_DIV_DISP1_0_VAL , &clk->div_disp10); + +/* AUDIO BLK */ +writel (AUDIO0_SEL_EPLL , &clk->src_mau); +writel (DIV_MAU_VAL , &clk->div_mau); + +/* FSYS */ +writel (CLK_SRC_FSYS0_VAL , &clk->src_fsys); +writel (CLK_DIV_FSYS0_VAL , &clk->div_fsys0); +writel (CLK_DIV_FSYS1_VAL , &clk->div_fsys1); +writel (CLK_DIV_FSYS2_VAL , &clk->div_fsys2); + +writel (CLK_SRC_ISP_VAL , &clk->src_isp); +writel (CLK_DIV_ISP0_VAL , &clk->div_isp0); +writel (CLK_DIV_ISP1_VAL , &clk->div_isp1); + +writel (CLK_SRC_PERIC0_VAL , &clk->src_peric0); +writel (CLK_SRC_PERIC1_VAL , &clk->src_peric1); + +writel (CLK_DIV_PERIC0_VAL , &clk->div_peric0); +writel (CLK_DIV_PERIC1_VAL , &clk->div_peric1); +writel (CLK_DIV_PERIC2_VAL , &clk->div_peric2); +writel (CLK_DIV_PERIC3_VAL , &clk->div_peric3); +writel (CLK_DIV_PERIC4_VAL , &clk->div_peric4); + +writel (CLK_DIV_CPERI1_VAL , &clk->div_cperi1); + +writel (CLK_DIV2_RATIO , &clk->clkdiv2_ratio); +writel (CLK_DIV4_RATIO , &clk->clkdiv4_ratio); +writel (CLK_DIV_G2D , &clk->div_g2d); + +writel (CLK_SRC_TOP6_VAL , &clk->src_top6); +writel (CLK_SRC_CDREX_VAL , &clk->src_cdrex); +writel (CLK_SRC_KFC_VAL , &clk->src_kfc); +} + +void system_clock_init (void )
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c void system_clock_init() · line 969
Quoted 10 lines
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +7
-0+{ +if (proid_is_exynos5420 ()) +exynos5420_system_clock_init (); +else +exynos5250_system_clock_init (); +} +void clock_init_dp_clock (void ) { struct exynos5_clock *clk =
Thanks,
Minkyu Kang.
PATCH v8 4/9 Exynos5420: Add DDR3 initialization for 5420
In reply to Rajeshwari S ShindeThis patch intends to add DDR3 initialization code for Exynos5420.
---
Changes in V2:
- Corrected a compilation issue for SMDK5250.
Changes in V3:
- None
Changes in V4:
- None
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Fixed multi line comment.
Changes in V8:
- None
arch/arm/cpu/armv7/exynos/dmc_common.c | 10 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 421 +++++++++++++++++++++++++++++- arch/arm/include/asm/arch-exynos/cpu.h | 4 + arch/arm/include/asm/arch-exynos/dmc.h | 123 ++++++--- 4 files changed, 513 insertions(+), 45 deletions(-)
arch/arm/cpu/armv7/exynos/dmc_common.c +1 -9
@@ -1,5 +1,5 @@/* -* Mem setup common file for different types of DDR present on SMDK5250 boards. +* Mem setup common file for different types of DDR present on Exynos boards. * * Copyright (C) 2012 Samsung Electronics *
@@ -152,14 +152,6 @@ void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc) } } -void dmc_config_memory (struct mem_timings *mem,struct exynos5_dmc *dmc) -{ -writel (mem->memconfig, &dmc->memconfig0); -writel (mem->memconfig, &dmc->memconfig1); -writel (DMC_MEMBASECONFIG0_VAL , &dmc->membaseconfig0); -writel (DMC_MEMBASECONFIG1_VAL , &dmc->membaseconfig1); -} -void mem_ctrl_init (int reset) {struct spl_machine_param *param =spl_get_machine_params ();
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +417 -4
447 lines not on this page · raw message
arch/arm/include/asm/arch-exynos/cpu.h +4 -0
@@ -162,6 +162,10 @@#define EXYNOS5420_ADC_BASE DEVICE_NOT_AVAILABLE#define EXYNOS5420_MODEM_BASE DEVICE_NOT_AVAILABLE +#define PAD_RETENTION_DRAM_STATUS (EXYNOS5420_POWER_BASE + 0x3004) +#define PAD_RETENTION_DRAM_COREBLK_OPTION (EXYNOS5420_POWER_BASE + 0x31E8) +#define PAD_RETENTION_DRAM_COREBLK_VAL 0x10000000 +#ifndef __ASSEMBLY__#include <asm/io.h> /* CPU detection macros */
arch/arm/include/asm/arch-exynos/dmc.h +91 -32
186 lines not on this page · raw message
Signature · 1 line
1.7.12.4
A message that is not in the archive (sent off-list or not yet received): [email protected]
Minkyu Kang
NAKPATCH v8 4/9 Exynos5420: Add DDR3 initialization for 5420
ping.
-------- Original Message --------
Subject: Re: [PATCH 4/9 v8] Exynos5420: Add DDR3 initialization for 5420
Date: Thu, 21 Nov 2013 16:13:24 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com
Dear Rajeshwari,
Quoted 94 lines · Rajeshwari S Shinde
This patch intends to add DDR3 initialization code for Exynos5420.
Signed-off-by Rajeshwari S Shinde <[email protected]>Signed-off-by Akshay Saraswat <[email protected]>Acked-by Simon Glass <[email protected]>---
Changes in V2:
- Corrected a compilation issue for SMDK5250.
Changes in V3:
- None
Changes in V4:
- None
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Fixed multi line comment.
Changes in V8:
- Nonearch/arm/cpu/armv7/exynos/dmc_common.c | 10 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 421 +++++++++++++++++++++++++++++- arch/arm/include/asm/arch-exynos/cpu.h | 4 + arch/arm/include/asm/arch-exynos/dmc.h | 123 ++++++--- 4 files changed, 513 insertions(+), 45 deletions(-)arch/arm/cpu/armv7/exynos/dmc_common.c +1
-9@@ -1,5 +1,5 @@/* -* Mem setup common file for different types of DDR present on SMDK5250 boards. +* Mem setup common file for different types of DDR present on Exynos boards. * * Copyright (C) 2012 Samsung Electronics * @@ -152,14 +152,6 @@ void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc) } } -void dmc_config_memory (struct mem_timings *mem,struct exynos5_dmc *dmc) -{ -writel (mem->memconfig, &dmc->memconfig0); -writel (mem->memconfig, &dmc->memconfig1); -writel (DMC_MEMBASECONFIG0_VAL , &dmc->membaseconfig0); -writel (DMC_MEMBASECONFIG1_VAL , &dmc->membaseconfig1); -} -void mem_ctrl_init (int reset) {struct spl_machine_param *param =spl_get_machine_params ();arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +5
-4@@ -1,5 +1,5 @@/* -* DDR3 mem setup file for SMDK5250 board based on EXYNOS5 +* DDR3 mem setup file for board based on EXYNOS5 * * Copyright (C) 2012 Samsung Electronics * @@ -15,8 +15,9 @@#include "exynos5_setup.h" #include "clock_init.h" -#define RDLVL_COMPLETE_TIMEOUT 10000 +#define TIMEOUT 10000 +#ifdef CONFIG_EXYNOS5250 static void reset_phy_ctrl (void ) { struct exynos5_clock *clk =@@ -108,7 +109,7 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,/* Precharge Configuration */ writel (mem->prechconfig_tp_cnt <<PRECHCONFIG_TP_CNT_SHIFT , - &dmc->prechconfig); + &dmc->prechconfig0);/* Power Down mode Configuration */ writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |@@ -174,7 +175,7 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,writel (val, &phy1_ctrl->phy_con1);writel (CTRL_RDLVL_GATE_ENABLE , &dmc->rdlvl_config); - i =RDLVL_COMPLETE_TIMEOUT ; + i =TIMEOUT ;while ((readl (&dmc->phystatus) & (RDLVL_COMPLETE_CHO |RDLVL_COMPLETE_CH1 )) != (RDLVL_COMPLETE_CHO |RDLVL_COMPLETE_CH1 ) && i >0 ) {@@ -215,3 +216,415 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size, | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size, · line 226
Quoted 10 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +8
-0return 0 ; } +#endif + +#ifdef CONFIG_EXYNOS5420 +int ddr3_mem_ctrl_init (struct mem_timings *mem,unsigned long mem_iv_size, +int reset) +{ +struct exynos5420_clock *clk = + (struct exynos5420_clock *)EXYNOS5_CLOCK_BASE ;
samsung_get_base_clock();
Quoted 5 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +5
-0+struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl; +struct exynos5_dmc *drex0, *drex1; +struct exynos5_tzasc *tzasc0, *tzasc1; +uint32_t val, n_lock_r, n_lock_w_phy0, n_lock_w_phy1; +int chip;
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size, · line 241
Quoted 10 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +10
-0+int i; + + phy0_ctrl = (struct exynos5_phy_control *)samsung_get_base_dmc_phy (); + phy1_ctrl = (struct exynos5_phy_control *)(samsung_get_base_dmc_phy () + +DMC_OFFSET ); + drex0 = (struct exynos5_dmc *)samsung_get_base_dmc_ctrl (); + drex1 = (struct exynos5_dmc *)(samsung_get_base_dmc_ctrl () + +DMC_OFFSET ); + tzasc0 = (struct exynos5_tzasc *)EXYNOS5420_DMC_TZASC0_BASE ; + tzasc1 = (struct exynos5_tzasc *)EXYNOS5420_DMC_TZASC1_BASE ;
No, we don't allow direct access to the base adress.
Quoted 394 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +389
-0+ +/* Enable PAUSE for DREX */ +setbits_le32 (&clk->pause,ENABLE_BIT ); + +/* Enable BYPASS mode */ +setbits_le32 (&clk->bpll_con1,BYPASS_EN ); + +writel (MUX_BPLL_SEL_FOUTBPLL , &clk->src_cdrex); +do { + val =readl (&clk->mux_stat_cdrex); + val &=BPLL_SEL_MASK ; + }while (val !=FOUTBPLL ); + +clrbits_le32 (&clk->bpll_con1,BYPASS_EN ); + +/* Specify the DDR memory type as DDR3 */ + val =readl (&phy0_ctrl->phy_con0); + val &= ~(PHY_CON0_CTRL_DDR_MODE_MASK <<PHY_CON0_CTRL_DDR_MODE_SHIFT ); + val |= (DDR_MODE_DDR3 <<PHY_CON0_CTRL_DDR_MODE_SHIFT ); +writel (val, &phy0_ctrl->phy_con0); + + val =readl (&phy1_ctrl->phy_con0); + val &= ~(PHY_CON0_CTRL_DDR_MODE_MASK <<PHY_CON0_CTRL_DDR_MODE_SHIFT ); + val |= (DDR_MODE_DDR3 <<PHY_CON0_CTRL_DDR_MODE_SHIFT ); +writel (val, &phy1_ctrl->phy_con0); + +/* Set Read Latency and Burst Length for PHY0 and PHY1 */ + val = (mem->ctrl_bstlen <<PHY_CON42_CTRL_BSTLEN_SHIFT ) | + (mem->ctrl_rdlat <<PHY_CON42_CTRL_RDLAT_SHIFT ); +writel (val, &phy0_ctrl->phy_con42); +writel (val, &phy1_ctrl->phy_con42); + + val =readl (&phy0_ctrl->phy_con26); + val &= ~(T_WRDATA_EN_MASK <<T_WRDATA_EN_OFFSET ); + val |= (T_WRDATA_EN_DDR3 <<T_WRDATA_EN_OFFSET ); +writel (val, &phy0_ctrl->phy_con26); + + val =readl (&phy1_ctrl->phy_con26); + val &= ~(T_WRDATA_EN_MASK <<T_WRDATA_EN_OFFSET ); + val |= (T_WRDATA_EN_DDR3 <<T_WRDATA_EN_OFFSET ); +writel (val, &phy1_ctrl->phy_con26); + +/* +* Set Driver strength for CK, CKE, CS & CA to 0x7 +* Set Driver strength for Data Slice 0~3 to 0x7 +*/ + val = (0x7 <<CA_CK_DRVR_DS_OFFSET ) | (0x7 <<CA_CKE_DRVR_DS_OFFSET ) | + (0x7 <<CA_CS_DRVR_DS_OFFSET ) | (0x7 <<CA_ADR_DRVR_DS_OFFSET ); + val |= (0x7 <<DA_3_DS_OFFSET ) | (0x7 <<DA_2_DS_OFFSET ) | + (0x7 <<DA_1_DS_OFFSET ) | (0x7 <<DA_0_DS_OFFSET ); +writel (val, &phy0_ctrl->phy_con39); +writel (val, &phy1_ctrl->phy_con39); + +/* ZQ Calibration */ +if (dmc_config_zq (mem, phy0_ctrl, phy1_ctrl)) +return SETUP_ERR_ZQ_CALIBRATION_FAILURE ; + +clrbits_le32 (&phy0_ctrl->phy_con16,ZQ_CLK_DIV_EN ); +clrbits_le32 (&phy1_ctrl->phy_con16,ZQ_CLK_DIV_EN ); + +/* DQ Signal */ + val =readl (&phy0_ctrl->phy_con14); + val |= mem->phy0_pulld_dqs; +writel (val, &phy0_ctrl->phy_con14); + val =readl (&phy1_ctrl->phy_con14); + val |= mem->phy1_pulld_dqs; +writel (val, &phy1_ctrl->phy_con14); + + val =MEM_TERM_EN |PHY_TERM_EN ; +writel (val, &drex0->phycontrol0); +writel (val, &drex1->phycontrol0); + +writel (mem->concontrol | + (mem->dfi_init_start <<CONCONTROL_DFI_INIT_START_SHIFT ) | + (mem->rd_fetch <<CONCONTROL_RD_FETCH_SHIFT ), + &drex0->concontrol); +writel (mem->concontrol | + (mem->dfi_init_start <<CONCONTROL_DFI_INIT_START_SHIFT ) | + (mem->rd_fetch <<CONCONTROL_RD_FETCH_SHIFT ), + &drex1->concontrol); + +do { + val =readl (&drex0->phystatus); + }while ((val &DFI_INIT_COMPLETE ) !=DFI_INIT_COMPLETE ); +do { + val =readl (&drex1->phystatus); + }while ((val &DFI_INIT_COMPLETE ) !=DFI_INIT_COMPLETE ); + +clrbits_le32 (&drex0->concontrol,DFI_INIT_START ); +clrbits_le32 (&drex1->concontrol,DFI_INIT_START ); + +update_reset_dll (drex0,DDR_MODE_DDR3 ); +update_reset_dll (drex1,DDR_MODE_DDR3 ); + +/* +* Set Base Address: +* 0x2000_0000 ~ 0x5FFF_FFFF +* 0x6000_0000 ~ 0x9FFF_FFFF +*/ +/* MEMBASECONFIG0 */ + val =DMC_MEMBASECONFIGX_CHIP_BASE (DMC_CHIP_BASE_0 ) | +DMC_MEMBASECONFIGX_CHIP_MASK (DMC_CHIP_MASK ); +writel (val, &tzasc0->membaseconfig0); +writel (val, &tzasc1->membaseconfig0); + +/* MEMBASECONFIG1 */ + val =DMC_MEMBASECONFIGX_CHIP_BASE (DMC_CHIP_BASE_1 ) | +DMC_MEMBASECONFIGX_CHIP_MASK (DMC_CHIP_MASK ); +writel (val, &tzasc0->membaseconfig1); +writel (val, &tzasc1->membaseconfig1); + +/* +* Memory Channel Inteleaving Size +* Ares Channel interleaving = 128 bytes +*/ +/* MEMCONFIG0/1 */ +writel (mem->memconfig, &tzasc0->memconfig0); +writel (mem->memconfig, &tzasc1->memconfig0); +writel (mem->memconfig, &tzasc0->memconfig1); +writel (mem->memconfig, &tzasc1->memconfig1); + +/* Precharge Configuration */ +writel (mem->prechconfig_tp_cnt <<PRECHCONFIG_TP_CNT_SHIFT , + &drex0->prechconfig0); +writel (mem->prechconfig_tp_cnt <<PRECHCONFIG_TP_CNT_SHIFT , + &drex1->prechconfig0); + +/* +* TimingRow, TimingData, TimingPower and Timingaref +* values as per Memory AC parameters +*/ +writel (mem->timing_ref, &drex0->timingref); +writel (mem->timing_ref, &drex1->timingref); +writel (mem->timing_row, &drex0->timingrow); +writel (mem->timing_row, &drex1->timingrow); +writel (mem->timing_data, &drex0->timingdata); +writel (mem->timing_data, &drex1->timingdata); +writel (mem->timing_power, &drex0->timingpower); +writel (mem->timing_power, &drex1->timingpower); + +if (reset) { +/* +* Send NOP, MRS and ZQINIT commands +* Sending MRS command will reset the DRAM. We should not be +* reseting the DRAM after resume, this will lead to memory +* corruption as DRAM content is lost after DRAM reset +*/ +dmc_config_mrs (mem, drex0); +dmc_config_mrs (mem, drex1); + }else { +/* +* During Suspend-Resume & S/W-Reset, as soon as PMU releases +* pad retention, CKE goes high. This causes memory contents +* not to be retained during DRAM initialization. Therfore, +* there is a new control register(0x100431e8[28]) which lets us +* release pad retention and retain the memory content until the +* initialization is complete. +*/ +writel (PAD_RETENTION_DRAM_COREBLK_VAL , +PAD_RETENTION_DRAM_COREBLK_OPTION ); +do { + val =readl (PAD_RETENTION_DRAM_STATUS ); + }while (val !=0x1 ); + +/* +* CKE PAD retention disables DRAM self-refresh mode. +* Send auto refresh command for DRAM refresh. +*/ +for (i =0 ; i <128 ; i++) { +for (chip =0 ; chip < mem->chips_to_configure; chip++) { +writel (DIRECT_CMD_REFA | + (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex0->directcmd); +writel (DIRECT_CMD_REFA | + (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex1->directcmd); + } + } + } + +if (mem->gate_leveling_enable) { +writel (PHY_CON0_RESET_VAL , &phy0_ctrl->phy_con0); +writel (PHY_CON0_RESET_VAL , &phy1_ctrl->phy_con0); + +setbits_le32 (&phy0_ctrl->phy_con0,P0_CMD_EN ); +setbits_le32 (&phy1_ctrl->phy_con0,P0_CMD_EN ); + + val =PHY_CON2_RESET_VAL ; + val |=INIT_DESKEW_EN ; +writel (val, &phy0_ctrl->phy_con2); +writel (val, &phy1_ctrl->phy_con2); + + val =readl (&phy0_ctrl->phy_con1); + val |= (RDLVL_PASS_ADJ_VAL <<RDLVL_PASS_ADJ_OFFSET ); +writel (val, &phy0_ctrl->phy_con1); + + val =readl (&phy1_ctrl->phy_con1); + val |= (RDLVL_PASS_ADJ_VAL <<RDLVL_PASS_ADJ_OFFSET ); +writel (val, &phy1_ctrl->phy_con1); + + n_lock_r =readl (&phy0_ctrl->phy_con13); + n_lock_w_phy0 = (n_lock_r &CTRL_LOCK_COARSE_MASK ) >>2 ; + n_lock_r =readl (&phy0_ctrl->phy_con12); + n_lock_r &= ~CTRL_DLL_ON ; + n_lock_r |= n_lock_w_phy0; +writel (n_lock_r, &phy0_ctrl->phy_con12); + + n_lock_r =readl (&phy1_ctrl->phy_con13); + n_lock_w_phy1 = (n_lock_r &CTRL_LOCK_COARSE_MASK ) >>2 ; + n_lock_r =readl (&phy1_ctrl->phy_con12); + n_lock_r &= ~CTRL_DLL_ON ; + n_lock_r |= n_lock_w_phy1; +writel (n_lock_r, &phy1_ctrl->phy_con12); + + val = (0x3 <<DIRECT_CMD_BANK_SHIFT ) |0x4 ; +for (chip =0 ; chip < mem->chips_to_configure; chip++) { +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex0->directcmd); +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex1->directcmd); + } + +setbits_le32 (&phy0_ctrl->phy_con2,RDLVL_GATE_EN ); +setbits_le32 (&phy1_ctrl->phy_con2,RDLVL_GATE_EN ); + +setbits_le32 (&phy0_ctrl->phy_con0,CTRL_SHGATE ); +setbits_le32 (&phy1_ctrl->phy_con0,CTRL_SHGATE ); + + val =readl (&phy0_ctrl->phy_con1); + val &= ~(CTRL_GATEDURADJ_MASK ); +writel (val, &phy0_ctrl->phy_con1); + + val =readl (&phy1_ctrl->phy_con1); + val &= ~(CTRL_GATEDURADJ_MASK ); +writel (val, &phy1_ctrl->phy_con1); + +writel (CTRL_RDLVL_GATE_ENABLE , &drex0->rdlvl_config); + i =TIMEOUT ; +while (((readl (&drex0->phystatus) &RDLVL_COMPLETE_CHO ) != +RDLVL_COMPLETE_CHO ) && (i >0 )) { +/* +* TODO(waihong): Comment on how long this take to +* timeout +*/ +sdelay (100 ); + i--; + } +if (!i) +return SETUP_ERR_RDLV_COMPLETE_TIMEOUT ; +writel (CTRL_RDLVL_GATE_DISABLE , &drex0->rdlvl_config); + +writel (CTRL_RDLVL_GATE_ENABLE , &drex1->rdlvl_config); + i =TIMEOUT ; +while (((readl (&drex1->phystatus) &RDLVL_COMPLETE_CHO ) != +RDLVL_COMPLETE_CHO ) && (i >0 )) { +/* +* TODO(waihong): Comment on how long this take to +* timeout +*/ +sdelay (100 ); + i--; + } +if (!i) +return SETUP_ERR_RDLV_COMPLETE_TIMEOUT ; +writel (CTRL_RDLVL_GATE_DISABLE , &drex1->rdlvl_config); + +writel (0 , &phy0_ctrl->phy_con14); +writel (0 , &phy1_ctrl->phy_con14); + + val = (0x3 <<DIRECT_CMD_BANK_SHIFT ); +for (chip =0 ; chip < mem->chips_to_configure; chip++) { +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex0->directcmd); +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex1->directcmd); + } + +if (mem->read_leveling_enable) { +/* Set Read DQ Calibration */ + val = (0x3 <<DIRECT_CMD_BANK_SHIFT ) |0x4 ; +for (chip =0 ; chip < mem->chips_to_configure; chip++) { +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex0->directcmd); +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex1->directcmd); + } + + val =readl (&phy0_ctrl->phy_con1); + val |=READ_LEVELLING_DDR3 ; +writel (val, &phy0_ctrl->phy_con1); + val =readl (&phy1_ctrl->phy_con1); + val |=READ_LEVELLING_DDR3 ; +writel (val, &phy1_ctrl->phy_con1); + + val =readl (&phy0_ctrl->phy_con2); + val |= (RDLVL_EN |RDLVL_INCR_ADJ ); +writel (val, &phy0_ctrl->phy_con2); + val =readl (&phy1_ctrl->phy_con2); + val |= (RDLVL_EN |RDLVL_INCR_ADJ ); +writel (val, &phy1_ctrl->phy_con2); + +setbits_le32 (&drex0->rdlvl_config, +CTRL_RDLVL_DATA_ENABLE ); + i =TIMEOUT ; +while (((readl (&drex0->phystatus) &RDLVL_COMPLETE_CHO ) + !=RDLVL_COMPLETE_CHO ) && (i >0 )) { +/* +* TODO(waihong): Comment on how long this take +* to timeout +*/ +sdelay (100 ); + i--; + } +if (!i) +return SETUP_ERR_RDLV_COMPLETE_TIMEOUT ; + +clrbits_le32 (&drex0->rdlvl_config, +CTRL_RDLVL_DATA_ENABLE ); +setbits_le32 (&drex1->rdlvl_config, +CTRL_RDLVL_DATA_ENABLE ); + i =TIMEOUT ; +while (((readl (&drex1->phystatus) &RDLVL_COMPLETE_CHO ) + !=RDLVL_COMPLETE_CHO ) && (i >0 )) { +/* +* TODO(waihong): Comment on how long this take +* to timeout +*/ +sdelay (100 ); + i--; + } +if (!i) +return SETUP_ERR_RDLV_COMPLETE_TIMEOUT ; + +clrbits_le32 (&drex1->rdlvl_config, +CTRL_RDLVL_DATA_ENABLE ); + + val = (0x3 <<DIRECT_CMD_BANK_SHIFT ); +for (chip =0 ; chip < mem->chips_to_configure; chip++) { +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex0->directcmd); +writel (val | (chip <<DIRECT_CMD_CHIP_SHIFT ), + &drex1->directcmd); + } + +update_reset_dll (drex0,DDR_MODE_DDR3 ); +update_reset_dll (drex1,DDR_MODE_DDR3 ); + } + +/* Common Settings for Leveling */ + val =PHY_CON12_RESET_VAL ; +writel ((val + n_lock_w_phy0), &phy0_ctrl->phy_con12); +writel ((val + n_lock_w_phy1), &phy1_ctrl->phy_con12); + +setbits_le32 (&phy0_ctrl->phy_con2,DLL_DESKEW_EN ); +setbits_le32 (&phy1_ctrl->phy_con2,DLL_DESKEW_EN ); + } + +/* Send PALL command */ +dmc_config_prech (mem, drex0); +dmc_config_prech (mem, drex1); + +writel (mem->memcontrol, &drex0->memcontrol); +writel (mem->memcontrol, &drex1->memcontrol); + +/* +* Set DMC Concontrol: Enable auto-refresh counter, provide +* read data fetch cycles and enable DREX auto set powerdown +* for input buffer of I/O in none read memory state. +*/ +writel (mem->concontrol | (mem->aref_en <<CONCONTROL_AREF_EN_SHIFT ) | + (mem->rd_fetch <<CONCONTROL_RD_FETCH_SHIFT )| +DMC_CONCONTROL_IO_PD_CON (0x2 ), + &drex0->concontrol); +writel (mem->concontrol | (mem->aref_en <<CONCONTROL_AREF_EN_SHIFT ) | + (mem->rd_fetch <<CONCONTROL_RD_FETCH_SHIFT )| +DMC_CONCONTROL_IO_PD_CON (0x2 ), + &drex1->concontrol); + +/* +* Enable Clock Gating Control for DMC +* this saves around 25 mw dmc power as compared to the power +* consumption without these bits enabled +*/ +setbits_le32 (&drex0->cgcontrol,DMC_INTERNAL_CG ); +setbits_le32 (&drex1->cgcontrol,DMC_INTERNAL_CG ); + + return 0; +} +#endif arch/arm/include/asm/arch-exynos/cpu.h +0
-0
arch/arm/include/asm/arch-exynos/cpu.h line 166
Quoted 5 lines
arch/arm/include/asm/arch-exynos/cpu.h +2
-0@@ -162,6 +162,10 @@#define EXYNOS5420_ADC_BASE DEVICE_NOT_AVAILABLE#define EXYNOS5420_MODEM_BASE DEVICE_NOT_AVAILABLE +#define PAD_RETENTION_DRAM_STATUS (EXYNOS5420_POWER_BASE + 0x3004) +#define PAD_RETENTION_DRAM_COREBLK_OPTION (EXYNOS5420_POWER_BASE + 0x31E8)
NAK.
These are not a base address.
You should add this registers at structure of power.
arch/arm/include/asm/arch-exynos/cpu.h line 167
Quoted 1 line
arch/arm/include/asm/arch-exynos/cpu.h +1
-0+#define PAD_RETENTION_DRAM_COREBLK_VAL 0x10000000
please move it to somewhere.
Quoted 194 lines
arch/arm/include/asm/arch-exynos/cpu.h +1
-0+#ifndef __ASSEMBLY__#include <asm/io.h> /* CPU detection macros */ arch/arm/include/asm/arch-exynos/dmc.h +90
-32@@ -114,13 +114,24 @@ struct exynos4_dmc {struct exynos5_dmc {unsigned int concontrol;unsigned int memcontrol; + +/* +* Between 5250 and 5420, the DMC Register differs only at 0x8 offset. +* So to use the same structure and simplify the code put a define to +* distinguish between memconfig0 and cgcontrol register +*/ +#ifdef CONFIG_EXYNOS5250 unsigned int memconfig0; +#else +unsigned int cgcontrol; +#endif unsigned int memconfig1;unsigned int directcmd; -unsigned int prechconfig; +unsigned int prechconfig0;unsigned int phycontrol0; -unsigned char res1[0xc ]; -unsigned int pwrdnconfig; +unsigned int prechconfig1; +unsigned char res1[0x8 ]; +unsigned int pwrdnconfig;/* 0x0028*/ unsigned int timingpzq;unsigned int timingref;unsigned int timingrow;@@ -128,12 +139,12 @@ struct exynos5_dmc {unsigned int timingpower;unsigned int phystatus;unsigned char res2[0x4 ]; -unsigned int chipstatus_ch0; +unsigned int chipstatus_ch0;/* 0x0048 */ unsigned int chipstatus_ch1;unsigned char res3[0x4 ];unsigned int mrstatus;unsigned char res4[0x8 ]; -unsigned int qoscontrol0; +unsigned int qoscontrol0;/* 0x0060 */ unsigned char resr5[0x4 ];unsigned int qoscontrol1;unsigned char res6[0x4 ];@@ -164,45 +175,83 @@ struct exynos5_dmc {unsigned int qoscontrol14;unsigned char res19[0x4 ];unsigned int qoscontrol15; -unsigned char res20[0x14 ]; +unsigned char res20[0x4 ]; +unsigned int timing_set_sw;/* 0x00e0 */ +unsigned int timingrow1; +unsigned int timingdata1; +unsigned int timingpower1;unsigned int ivcontrol;unsigned int wrtra_config;unsigned int rdlvl_config; -unsigned char res21[0x8 ]; +unsigned char res21[0x4 ]; +unsigned int brbrsvcontrol;/* 0x0100*/ unsigned int brbrsvconfig;unsigned int brbqosconfig;unsigned int membaseconfig0; -unsigned int membaseconfig1; +unsigned int membaseconfig1;/* 0x0110 */ unsigned char res22[0xc ]; -unsigned int wrlvl_config; -unsigned char res23[0xc ]; -unsigned int perevcontrol; +unsigned int wrlvl_config0;/* 0x0120 */ +unsigned int wrlvl_config1; +unsigned int wrlvl_status; +unsigned char res23[0x4 ]; +unsigned int perevcontrol;/* 0x0130 */ unsigned int perev0config;unsigned int perev1config;unsigned int perev2config;unsigned int perev3config; -unsigned char res24[0xdebc ]; -unsigned int pmnc_ppc_a; -unsigned char res25[0xc ]; -unsigned int cntens_ppc_a; -unsigned char res26[0xc ]; -unsigned int cntenc_ppc_a; -unsigned char res27[0xc ]; -unsigned int intens_ppc_a; -unsigned char res28[0xc ]; -unsigned int intenc_ppc_a; -unsigned char res29[0xc ]; -unsigned int flag_ppc_a; -unsigned char res30[0xac ]; -unsigned int ccnt_ppc_a; -unsigned char res31[0xc ]; -unsigned int pmcnt0_ppc_a; +unsigned char res22a[0xc ]; +unsigned int ctrl_io_rdata_ch0; +unsigned int ctrl_io_rdata_ch1; +unsigned char res23a[0x8 ]; +unsigned int cacal_config0; +unsigned int cacal_config1; +unsigned int cacal_status; +unsigned char res24[0x94 ]; +unsigned int emergent_config0;/* 0x0200 */ +unsigned int emergent_config1; +unsigned char res25[0x8 ]; +unsigned int bp_control0; +unsigned int bp_control0_r; +unsigned int bp_control0_w; +unsigned char res26[0x4 ]; +unsigned int bp_control1; +unsigned int bp_control1_r; +unsigned int bp_control1_w; +unsigned char res27[0x4 ]; +unsigned int bp_control2; +unsigned int bp_control2_r; +unsigned int bp_control2_w; +unsigned char res28[0x4 ]; +unsigned int bp_control3; +unsigned int bp_control3_r; +unsigned int bp_control3_w; +unsigned char res29[0xb4 ]; +unsigned int winconfig_odt_w;/* 0x0300 */ +unsigned char res30[0x4 ]; +unsigned int winconfig_ctrl_read; +unsigned int winconfig_ctrl_gate; +unsigned char res31[0xdcf0 ]; +unsigned int pmnc_ppc;unsigned char res32[0xc ]; -unsigned int pmcnt1_ppc_a; +unsigned int cntens_ppc;unsigned char res33[0xc ]; -unsigned int pmcnt2_ppc_a; +unsigned int cntenc_ppc;unsigned char res34[0xc ]; -unsigned int pmcnt3_ppc_a; +unsigned int intens_ppc; +unsigned char res35[0xc ]; +unsigned int intenc_ppc; +unsigned char res36[0xc ]; +unsigned int flag_ppc;/* 0xe050 */ +unsigned char res37[0xac ]; +unsigned int ccnt_ppc; +unsigned char res38[0xc ]; +unsigned int pmcnt0_ppc; +unsigned char res39[0xc ]; +unsigned int pmcnt1_ppc; +unsigned char res40[0xc ]; +unsigned int pmcnt2_ppc; +unsigned char res41[0xc ]; +unsigned int pmcnt3_ppc;/* 0xe140 */ };struct exynos5_phy_control {@@ -211,13 +260,13 @@ struct exynos5_phy_control {unsigned int phy_con2;unsigned int phy_con3;unsigned int phy_con4; -unsigned char res1[4 ]; +unsigned int phy_con5;unsigned int phy_con6;unsigned char res2[4 ];unsigned int phy_con8;unsigned int phy_con9;unsigned int phy_con10; -unsigned char res3[4 ]; +unsigned int phy_con11;unsigned int phy_con12;unsigned int phy_con13;unsigned int phy_con14;@@ -252,6 +301,15 @@ struct exynos5_phy_control {unsigned int phy_con42; }; +struct exynos5_tzasc { +unsigned char res1[0xf00 ]; +unsigned int membaseconfig0; +unsigned int membaseconfig1; +unsigned char res2[0x8 ]; +unsigned int memconfig0; +unsigned int memconfig1; +}; +enum ddr_mode {DDR_MODE_DDR2 ,DDR_MODE_DDR3 ,
arch/arm/include/asm/arch-exynos/dmc.h enum mem_manuf { · line 350
Quoted 7 lines
arch/arm/include/asm/arch-exynos/dmc.h +1
-0@@ -286,6 +344,7 @@ enum mem_manuf {#define PHY_CON0_T_WRRDCMD_SHIFT 17#define PHY_CON0_T_WRRDCMD_MASK (0x7 << PHY_CON0_T_WRRDCMD_SHIFT)#define PHY_CON0_CTRL_DDR_MODE_SHIFT 11 +#define PHY_CON0_CTRL_DDR_MODE_MASK 0x3/* PHY_CON1 register fields */ #define PHY_CON1_RDLVL_RDDATA_ADJ_SHIFT 0
Thanks,
Minkyu Kang.
PATCH v8 5/9 Exynos5420: Add support for 5420 in pinmux and gpio
In reply to Rajeshwari S ShindeAdds code in pinmux and gpio framework to support Exynos5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added correct calculation of gpio based addresses.
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the coding style nits.
Chnages in V8:
- Corrected the coding style nits pointed by Minkyu Kang.
arch/arm/cpu/armv7/exynos/pinmux.c | 260 +++++++++++++++++++++++++++++- arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++++++++++++-- arch/arm/include/asm/arch-exynos/periph.h | 3 + 3 files changed, 390 insertions(+), 16 deletions(-)
arch/arm/cpu/armv7/exynos/pinmux.c +258 -2
@@ -46,6 +46,42 @@ static void exynos5_uart_config(int peripheral) } } +static void exynos5420_uart_config (int peripheral) +{ +struct exynos5420_gpio_part1 *gpio1 = + (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1 (); +struct s5p_gpio_bank *bank; +int i, start, count; + +switch (peripheral) { +case PERIPH_ID_UART0 : + bank = &gpio1->a0; + start =0 ; + count =4 ; +break ; +case PERIPH_ID_UART1 : + bank = &gpio1->a0; + start =4 ; + count =4 ; +break ; +case PERIPH_ID_UART2 : + bank = &gpio1->a1; + start =0 ; + count =4 ; +break ; +case PERIPH_ID_UART3 : + bank = &gpio1->a1; + start =4 ; + count =2 ; +break ; + } + +for (i = start; i < start + count; i++) { +s5p_gpio_set_pull (bank, i,GPIO_PULL_NONE ); +s5p_gpio_cfg_pin (bank, i,GPIO_FUNC (0x2 )); + } +} +static int exynos5_mmc_config (int peripheral,int flags) { struct exynos5_gpio_part1 *gpio1 =
@@ -101,6 +137,75 @@ static int exynos5_mmc_config(int peripheral, int flags)return 0 ; } +static int exynos5420_mmc_config (int peripheral,int flags) +{ +struct exynos5420_gpio_part3 *gpio3 = + (struct exynos5420_gpio_part3 *)samsung_get_base_gpio_part3 (); +struct s5p_gpio_bank *bank =NULL , *bank_ext =NULL ; +int i, start; + +switch (peripheral) { +case PERIPH_ID_SDMMC0 : + bank = &gpio3->c0; + bank_ext = &gpio3->c3; + start =0 ; +break ; +case PERIPH_ID_SDMMC1 : + bank = &gpio3->c1; + bank_ext = &gpio3->d1; + start =4 ; +break ; +case PERIPH_ID_SDMMC2 : + bank = &gpio3->c2; + bank_ext =NULL ; + start =0 ; +break ; +default : + start =0 ; +debug ("%s: invalid peripheral %d" , __func__, peripheral); +return -1 ; + } + +if ((flags &PINMUX_FLAG_8BIT_MODE ) && !bank_ext) { +debug ("SDMMC device %d does not support 8bit mode" , + peripheral); +return -1 ; + } + +if (flags &PINMUX_FLAG_8BIT_MODE ) { +for (i = start; i <= (start +3 ); i++) { +s5p_gpio_cfg_pin (bank_ext, i,GPIO_FUNC (0x2 )); +s5p_gpio_set_pull (bank_ext, i,GPIO_PULL_UP ); +s5p_gpio_set_drv (bank_ext, i,GPIO_DRV_4X ); + } + } + +for (i =0 ; i <3 ; i++) { +/* +* MMC0 is intended to be used for eMMC. The +* card detect pin is used as a VDDEN signal to +* power on the eMMC. The 5420 iROM makes +* this same assumption. +*/ +if ((peripheral ==PERIPH_ID_SDMMC0 ) && (i ==2 )) { +s5p_gpio_set_value (bank, i,1 ); +s5p_gpio_cfg_pin (bank, i,GPIO_OUTPUT ); + }else { +s5p_gpio_cfg_pin (bank, i,GPIO_FUNC (0x2 )); + } +s5p_gpio_set_pull (bank, i,GPIO_PULL_NONE ); +s5p_gpio_set_drv (bank, i,GPIO_DRV_4X ); + } + +for (i =3 ; i <=6 ; i++) { +s5p_gpio_cfg_pin (bank, i,GPIO_FUNC (0x2 )); +s5p_gpio_set_pull (bank, i,GPIO_PULL_UP ); +s5p_gpio_set_drv (bank, i,GPIO_DRV_4X ); + } + +return 0 ; +} +static void exynos5_sromc_config (int flags) { struct exynos5_gpio_part1 *gpio1 =
@@ -216,6 +321,59 @@ static void exynos5_i2c_config(int peripheral, int flags) } } +static void exynos5420_i2c_config (int peripheral) +{ +struct exynos5420_gpio_part1 *gpio1 = + (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1 (); + +switch (peripheral) { +case PERIPH_ID_I2C0 : +s5p_gpio_cfg_pin (&gpio1->b3,0 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,1 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C1 : +s5p_gpio_cfg_pin (&gpio1->b3,2 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,3 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C2 : +s5p_gpio_cfg_pin (&gpio1->a0,6 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a0,7 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C3 : +s5p_gpio_cfg_pin (&gpio1->a1,2 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a1,3 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C4 : +s5p_gpio_cfg_pin (&gpio1->a2,0 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a2,1 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C5 : +s5p_gpio_cfg_pin (&gpio1->a2,2 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->a2,3 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C6 : +s5p_gpio_cfg_pin (&gpio1->b1,3 ,GPIO_FUNC (0x4 )); +s5p_gpio_cfg_pin (&gpio1->b1,4 ,GPIO_FUNC (0x4 )); +break ; +case PERIPH_ID_I2C7 : +s5p_gpio_cfg_pin (&gpio1->b2,2 ,GPIO_FUNC (0x3 )); +s5p_gpio_cfg_pin (&gpio1->b2,3 ,GPIO_FUNC (0x3 )); +break ; +case PERIPH_ID_I2C8 : +s5p_gpio_cfg_pin (&gpio1->b3,4 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,5 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C9 : +s5p_gpio_cfg_pin (&gpio1->b3,6 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b3,7 ,GPIO_FUNC (0x2 )); +break ; +case PERIPH_ID_I2C10 : +s5p_gpio_cfg_pin (&gpio1->b4,0 ,GPIO_FUNC (0x2 )); +s5p_gpio_cfg_pin (&gpio1->b4,1 ,GPIO_FUNC (0x2 )); +break ; + } +} +static void exynos5_i2s_config (int peripheral) {int i;
@@ -279,6 +437,58 @@ void exynos5_spi_config(int peripheral) } } +void exynos5420_spi_config (int peripheral) +{ +int cfg, pin, i; +struct s5p_gpio_bank *bank =NULL ; +struct exynos5420_gpio_part1 *gpio1 = + (struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1 (); +struct exynos5420_gpio_part4 *gpio4 = + (struct exynos5420_gpio_part4 *)samsung_get_base_gpio_part4 (); + +switch (peripheral) { +case PERIPH_ID_SPI0 : + bank = &gpio1->a2; + cfg =GPIO_FUNC (0x2 ); + pin =0 ; +break ; +case PERIPH_ID_SPI1 : + bank = &gpio1->a2; + cfg =GPIO_FUNC (0x2 ); + pin =4 ; +break ; +case PERIPH_ID_SPI2 : + bank = &gpio1->b1; + cfg =GPIO_FUNC (0x5 ); + pin =1 ; +break ; +case PERIPH_ID_SPI3 : + bank = &gpio4->f1; + cfg =GPIO_FUNC (0x2 ); + pin =0 ; +break ; +case PERIPH_ID_SPI4 : + cfg =0 ; + pin =0 ; +break ; +default : + cfg =0 ; + pin =0 ; +debug ("%s: invalid peripheral %d" , __func__, peripheral); +return ; + } + +if (peripheral !=PERIPH_ID_SPI4 ) { +for (i = pin; i < pin +4 ; i++) +s5p_gpio_cfg_pin (bank, i, cfg); + }else { +for (i =0 ; i <2 ; i++) { +s5p_gpio_cfg_pin (&gpio4->f0, i +2 ,GPIO_FUNC (0x4 )); +s5p_gpio_cfg_pin (&gpio4->e0, i +4 ,GPIO_FUNC (0x4 )); + } + } +} +static int exynos5_pinmux_config (int peripheral,int flags) {switch (peripheral) {
@@ -325,6 +535,48 @@ static int exynos5_pinmux_config(int peripheral, int flags)return 0 ; } +static int exynos5420_pinmux_config (int peripheral,int flags) +{ +switch (peripheral) { +case PERIPH_ID_UART0 : +case PERIPH_ID_UART1 : +case PERIPH_ID_UART2 : +case PERIPH_ID_UART3 : +exynos5420_uart_config (peripheral); +break ; +case PERIPH_ID_SDMMC0 : +case PERIPH_ID_SDMMC1 : +case PERIPH_ID_SDMMC2 : +case PERIPH_ID_SDMMC3 : +return exynos5420_mmc_config (peripheral, flags); +case PERIPH_ID_SPI0 : +case PERIPH_ID_SPI1 : +case PERIPH_ID_SPI2 : +case PERIPH_ID_SPI3 : +case PERIPH_ID_SPI4 : +exynos5420_spi_config (peripheral); +break ; +case PERIPH_ID_I2C0 : +case PERIPH_ID_I2C1 : +case PERIPH_ID_I2C2 : +case PERIPH_ID_I2C3 : +case PERIPH_ID_I2C4 : +case PERIPH_ID_I2C5 : +case PERIPH_ID_I2C6 : +case PERIPH_ID_I2C7 : +case PERIPH_ID_I2C8 : +case PERIPH_ID_I2C9 : +case PERIPH_ID_I2C10 : +exynos5420_i2c_config (peripheral); +break ; +default : +debug ("%s: invalid peripheral %d" , __func__, peripheral); +return -1 ; + } + +return 0 ; +} +static void exynos4_i2c_config (int peripheral,int flags) { struct exynos4_gpio_part1 *gpio1 =
@@ -475,13 +727,17 @@ static int exynos4_pinmux_config(int peripheral, int flags)int exynos_pinmux_config (int peripheral,int flags) {if (cpu_is_exynos5 ()) { -return exynos5_pinmux_config (peripheral, flags); +if (proid_is_exynos5420 ()) +return exynos5420_pinmux_config (peripheral, flags); +else if (proid_is_exynos5250 ()) +return exynos5_pinmux_config (peripheral, flags); }else if (cpu_is_exynos4 ()) {return exynos4_pinmux_config (peripheral, flags); }else {debug ("pinmux functionality not supported\n" ); -return -1 ; } + +return -1 ; }#ifdef CONFIG_OF_CONTROL
arch/arm/include/asm/arch-exynos/gpio.h +129 -14
164 lines not on this page · raw message
arch/arm/include/asm/arch-exynos/periph.h +3 -0
@@ -34,6 +34,9 @@ enum periph_id {PERIPH_ID_SDMMC1 ,PERIPH_ID_SDMMC2 ,PERIPH_ID_SDMMC3 , +PERIPH_ID_I2C8 =87 , +PERIPH_ID_I2C9 , +PERIPH_ID_I2C10 =203 ,PERIPH_ID_I2S0 =98 , PERIPH_ID_I2S1 = 99,
Signature · 1 line
1.7.12.4
PATCH v8 6/9 Exynos5420: Add base patch for SMDK5420
In reply to Rajeshwari S ShindeAdding the base patch for Exynos based SMDK5420. This shall enable compilation and basic boot support for SMDK5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Rebased on latest u-boot-samsung tree.
Changes in V5:
- Removed functions board_eth_init and board_mmc_init as they were moved to common/board.c
Changes in V6:
- None
Changes in V7:
- added CONFIG_EXYNOS_SPL to build 5420 and 5250
Changes in V8:
- None
board/samsung/common/board.c | 2 + board/samsung/smdk5420/Makefile | 34 ++++++++ board/samsung/smdk5420/smdk5420.c | 159 ++++++++++++++++++++++++++++++++++ board/samsung/smdk5420/smdk5420_spl.c | 52 +++++++++++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5250-dt.h | 1 + tools/Makefile | 3 +- 8 files changed, 252 insertions(+), 1 deletion(-) create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
board/samsung/common/board.c +2 -0
@@ -143,6 +143,7 @@ struct cros_ec_dev *board_get_cros_ec_dev(void)return local.cros_ec_dev; } +#ifdef CONFIG_CROS_EC static int board_init_cros_ec_devices (const void *blob) { local.cros_ec_err =cros_ec_init (blob, &local.cros_ec_dev);
@@ -151,6 +152,7 @@ static int board_init_cros_ec_devices(const void *blob) return 0; } +#endif #if defined(CONFIG_POWER )#ifdef CONFIG_POWER_MAX77686
board/samsung/smdk5420/Makefile new file +34 -0
@@ -0,0 +1,34 @@ +# +# Copyright (C) 2013 Samsung Electronics +# +# SPDX-License-Identifier: GPL-2.0+ +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS += smdk5420_spl.o + +ifndef CONFIG_SPL_BUILD +COBJS += smdk5420.o +endif + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) + +ALL := $(obj).depend $(LIB) + +all: $(ALL) + +$(LIB): $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################
board/samsung/smdk5420/smdk5420.c new file +159 -0
159 lines not on this page · raw message
board/samsung/smdk5420/smdk5420_spl.c new file +52 -0
52 lines not on this page · raw message
boards.cfg +1 -0
@@ -272,6 +272,7 @@ Active arm armv7 exynos samsung arndale Active arm armv7 exynos samsung origen origen - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung smdk5250 smdk5250 - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung smdk5250 snow - Rajeshwari Shinde <[email protected]> +Active arm armv7 exynos samsung smdk5420 smdk5420 - Rajeshwari Shinde <[email protected]> Active arm armv7 exynos samsung smdkv310 smdkv310 - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung trats trats - Lukasz Majewski <[email protected]> Active arm armv7 exynos samsung trats2 trats2 - Piotr Wilczek <[email protected]>
include/configs/arndale.h +1 -0
@@ -117,6 +117,7 @@#define CONFIG_USB_STORAGE /* MMC SPL */ +#define CONFIG_EXYNOS_SPL #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x02020030
include/configs/exynos5250-dt.h +1 -0
@@ -152,6 +152,7 @@#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20/* MMC SPL */ +#define CONFIG_EXYNOS_SPL #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x02020030
tools/Makefile +2 -1
@@ -53,6 +53,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX) BIN_FILES-y += mkenvimage$(SFX) BIN_FILES-y += mkimage$(SFX) BIN_FILES-$(CONFIG_EXYNOS5250) += mk$(BOARD)spl$(SFX) +BIN_FILES-$(CONFIG_EXYNOS5420) += mk$(BOARD)spl$(SFX) BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX) BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX) BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
@@ -87,7 +88,7 @@ NOPED_OBJ_FILES-y += ublimage.o OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o -OBJ_FILES-$(CONFIG_EXYNOS5250) += mkexynosspl.o +OBJ_FILES-$(CONFIG_EXYNOS_SPL) += mkexynosspl.o OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
Signature · 1 line
1.7.12.4
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v8 6/9 Exynos5420: Add base patch for SMDK5420
ping.
-------- Original Message --------
Subject: Re: [PATCH 6/9 v8] Exynos5420: Add base patch for SMDK5420
Date: Thu, 21 Nov 2013 16:24:14 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com
Dear Rajeshwari,
Quoted 226 lines · Rajeshwari S Shinde
Adding the base patch for Exynos based SMDK5420. This shall enable compilation and basic boot support for SMDK5420.
Signed-off-by Rajeshwari S Shinde <[email protected]>Signed-off-by Akshay Saraswat <[email protected]>---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Rebased on latest u-boot-samsung tree.
Changes in V5:
- Removed functionsboard_eth_initandboard_mmc_initas they were moved tocommon/board.c
Changes in V6:
- None
Changes in V7:
- addedCONFIG_EXYNOS_SPLto build 5420 and 5250
Changes in V8:
- Noneboard/samsung/common/board.c | 2 + board/samsung/smdk5420/Makefile | 34 ++++++++ board/samsung/smdk5420/smdk5420.c | 159 ++++++++++++++++++++++++++++++++++ board/samsung/smdk5420/smdk5420_spl.c | 52 +++++++++++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5250-dt.h | 1 + tools/Makefile | 3 +- 8 files changed, 252 insertions(+), 1 deletion(-) create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.cboard/samsung/common/board.c +2
-0@@ -143,6 +143,7 @@ struct cros_ec_dev *board_get_cros_ec_dev(void)return local.cros_ec_dev; } +#ifdef CONFIG_CROS_EC static int board_init_cros_ec_devices (const void *blob) { local.cros_ec_err =cros_ec_init (blob, &local.cros_ec_dev);@@ -151,6 +152,7 @@ static int board_init_cros_ec_devices(const void *blob) return 0; } +#endif #if defined(CONFIG_POWER )#ifdef CONFIG_POWER_MAX77686 board/samsung/smdk5420/Makefile new file +34
-0@@ -0,0 +1,34 @@ +# +# Copyright (C) 2013 Samsung Electronics +# +# SPDX-License-Identifier: GPL-2.0+ +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS += smdk5420_spl.o + +ifndef CONFIG_SPL_BUILD +COBJS += smdk5420.o +endif + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) + +ALL := $(obj).depend $(LIB) + +all: $(ALL) + +$(LIB): $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/samsung/smdk5420/smdk5420.c new file +125
-0@@ -0,0 +1,159 @@ +/* +* Copyright (C) 2013 Samsung Electronics +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <fdtdec.h> +#include <asm/io.h> +#include <i2c.h> +#include <lcd.h> +#include <spi.h> +#include <asm/arch/board.h> +#include <asm/arch/cpu.h> +#include <asm/arch/gpio.h> +#include <asm/arch/pinmux.h> +#include <asm/arch/dp_info.h> + +DECLARE_GLOBAL_DATA_PTR ; + +#ifdef CONFIG_USB_EHCI_EXYNOS +static int board_usb_vbus_init (void ) +{ +struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) +samsung_get_base_gpio_part1 (); + +/* Enable VBUS power switch */ +s5p_gpio_direction_output (&gpio1->x2,6 ,1 ); + +/* VBUS turn ON time */ +mdelay (3 ); + +return 0 ; +} +#endif + +int exynos_init (void ) +{ +#ifdef CONFIG_USB_EHCI_EXYNOS +board_usb_vbus_init (); +#endif +return 0 ; +} + +#ifdef CONFIG_LCD +void cfg_lcd_gpio (void ) +{ +struct exynos5_gpio_part1 *gpio1 = + (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1 (); + +/* For Backlight */ +s5p_gpio_cfg_pin (&gpio1->b2,0 ,GPIO_OUTPUT ); +s5p_gpio_set_value (&gpio1->b2,0 ,1 ); + +/* LCD power on */ +s5p_gpio_cfg_pin (&gpio1->x1,5 ,GPIO_OUTPUT ); +s5p_gpio_set_value (&gpio1->x1,5 ,1 ); + +/* Set Hotplug detect for DP */ +s5p_gpio_cfg_pin (&gpio1->x0,7 ,GPIO_FUNC (0x3 )); +} + +vidinfo_t panel_info = { + .vl_freq =60 , + .vl_col =2560 , + .vl_row =1600 , + .vl_width =2560 , + .vl_height =1600 , + .vl_clkp =CONFIG_SYS_LOW , + .vl_hsp =CONFIG_SYS_LOW , + .vl_vsp =CONFIG_SYS_LOW , + .vl_dp =CONFIG_SYS_LOW , + .vl_bpix =4 ,/* LCD_BPP = 2^4, for output conosle on LCD */ + +/* wDP panel timing infomation */ + .vl_hspw =32 , + .vl_hbpd =80 , + .vl_hfpd =48 , + + .vl_vspw =6 , + .vl_vbpd =37 , + .vl_vfpd =3 , + .vl_cmd_allow_len =0xf , + + .win_id =3 , + .cfg_gpio = cfg_lcd_gpio, + .backlight_on =NULL , + .lcd_power_on =NULL , + .reset_lcd =NULL , + .dual_lcd_enabled =0 , + + .init_delay =0 , + .power_on_delay =0 , + .reset_delay =0 , + .interface_mode =FIMD_RGB_INTERFACE , + .dp_enabled =1 , +}; + +static struct edp_device_info edp_info = { + .disp_info = { + .h_res =2560 , + .h_sync_width =32 , + .h_back_porch =80 , + .h_front_porch =48 , + .v_res =1600 , + .v_sync_width =6 , + .v_back_porch =37 , + .v_front_porch =3 , + .v_sync_rate =60 , + }, + .lt_info = { + .lt_status =DP_LT_NONE , + }, + .video_info = { + .master_mode =0 , + .bist_mode =DP_DISABLE , + .bist_pattern =NO_PATTERN , + .h_sync_polarity =0 , + .v_sync_polarity =0 , + .interlaced =0 , + .color_space =COLOR_RGB , + .dynamic_range =VESA , + .ycbcr_coeff =COLOR_YCBCR601 , + .color_depth =COLOR_8 , + },
board/samsung/smdk5420/smdk5420.c line 135
Quoted 10 lines
board/samsung/smdk5420/smdk5420.c new file +10
-0+}; + +static struct exynos_dp_platform_data dp_platform_data = { + .phy_enable = set_dp_phy_ctrl, + .edp_dev_info = &edp_info, +}; + +void init_panel_info (vidinfo_t *vid) +{ + vid->rgb_mode = MODE_RGB_P,
typo?
Did you try to build your patch?
Quoted 132 lines
board/samsung/smdk5420/smdk5420.c new file +24
-0+ + exynos_set_dp_platform_data(&dp_platform_data); +} +#endif + +int board_get_revision (void ) +{ +return 0 ; +} + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard (void ) +{ +const char *board_name; + + board_name =fdt_getprop (gd->fdt_blob,0 ,"model" ,NULL ); +if (board_name ==NULL ) +printf ("\nUnknown Board\n" ); +else +printf ("\nBoard: %s\n" , board_name); + +return 0 ; +} +#endif board/samsung/smdk5420/smdk5420_spl.c new file +52
-0@@ -0,0 +1,52 @@ +/* +* Copyright (C) 2013 The Chromium OS Authors. +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <asm/arch/cpu.h> +#include <asm/arch/spl.h> +#include <asm/arch/clk.h> + +#define SIGNATURE 0xdeadbeef + +/* Parameters of early board initialization in SPL */ +static struct spl_machine_param machine_param + __attribute__((section(".machine_param"))) = { + .signature = SIGNATURE, + .version = 1, + .params = "vmubfasirM", + .size = sizeof(machine_param), + + .mem_iv_size = 0x1f, + .mem_type = DDR_MODE_DDR3, + +/* +* Set uboot_size to 0x100000 bytes. +* +* This is an overly conservative value chosen to accommodate all +* possible U-Boot image. You are advised to set this value to a +* smaller realistic size via scripts that modifies the .machine_param +* section of output U-Boot image. +*/ + .uboot_size = 0x100000, + + .boot_source = BOOT_MODE_OM, + .frequency_mhz = 800, + .arm_freq_mhz = 900, + .serial_base = 0x12c30000, + .i2c_base = 0x12c60000, + .mem_manuf = MEM_MANUF_SAMSUNG, +}; + +struct spl_machine_param *spl_get_machine_params (void ) +{ +if (machine_param.signature !=SIGNATURE ) { +/* Will hang if SIGNATURE dont match */ +while (1 ) + ; + } + +return &machine_param; +}boards.cfg +1
-0@@ -272,6 +272,7 @@ Active arm armv7 exynos samsung arndale Active arm armv7 exynos samsung origen origen - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung smdk5250 smdk5250 - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung smdk5250 snow - Rajeshwari Shinde <[email protected]> +Active arm armv7 exynos samsung smdk5420 smdk5420 - Rajeshwari Shinde <[email protected]> Active arm armv7 exynos samsung smdkv310 smdkv310 - Chander Kashyap <[email protected]> Active arm armv7 exynos samsung trats trats - Lukasz Majewski <[email protected]> Active arm armv7 exynos samsung trats2 trats2 - Piotr Wilczek <[email protected]>include/configs/arndale.h +1
-0@@ -117,6 +117,7 @@#define CONFIG_USB_STORAGE /* MMC SPL */ +#define CONFIG_EXYNOS_SPL #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x02020030include/configs/exynos5250-dt.h +1
-0@@ -152,6 +152,7 @@#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20/* MMC SPL */ +#define CONFIG_EXYNOS_SPL #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x02020030tools/Makefile +1
-0@@ -53,6 +53,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX) BIN_FILES-y += mkenvimage$(SFX) BIN_FILES-y += mkimage$(SFX) BIN_FILES-$(CONFIG_EXYNOS5250) += mk$(BOARD)spl$(SFX) +BIN_FILES-$(CONFIG_EXYNOS5420) += mk$(BOARD)spl$(SFX) BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX) BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX) BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
tools/Makefile NOPED_OBJ_FILES-y += ublimage.o · line 94
Quoted 8 lines
tools/Makefile +1
-1@@ -87,7 +88,7 @@ NOPED_OBJ_FILES-y += ublimage.o OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o -OBJ_FILES-$(CONFIG_EXYNOS5250) += mkexynosspl.o +OBJ_FILES-$(CONFIG_EXYNOS_SPL) += mkexynosspl.o OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
Thanks,
Minkyu Kang.
PATCH v8 7/9 DTS: Add dts support for SMDK5420
In reply to Rajeshwari S ShindeThis patch adds dts support for SMDK5420.exynos5.dtsi created is a common file which has the nodes common to both 5420 and 5250.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added /include/ "exynos5420.dtsi
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the license.
Changes in V8:
- None
arch/arm/dts/exynos5.dtsi | 198 ++++++++++++++++++++++++++++++ arch/arm/dts/exynos5250.dtsi | 196 +---------------------------- arch/arm/dts/exynos5420.dtsi | 70 +++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 +++++++++++++++++++++++++ 4 files changed, 441 insertions(+), 192 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
arch/arm/dts/exynos5.dtsi new file +198 -0
@@ -0,0 +1,198 @@ +/* + * Copyright (c) 2013 The Chromium OS Authors + * SAMSUNG EXYNOS5 SoC device tree source + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/include/ "skeleton.dtsi" + +/ { + compatible = "samsung,exynos5"; + + sromc at 12250000 { + compatible = "samsung,exynos-sromc"; + reg = <0x12250000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c at 12c60000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C60000 0x100>; + interrupts = <0 56 0>; + }; + + i2c at 12c70000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C70000 0x100>; + interrupts = <0 57 0>; + }; + + i2c at 12c80000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C80000 0x100>; + interrupts = <0 58 0>; + }; + + i2c at 12c90000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,s3c2440-i2c"; + reg = <0x12C90000 0x100>; + interrupts = <0 59 0>; + }; + + spi at 12d20000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x12d20000 0x30>; + interrupts = <0 68 0>; + }; + + spi at 12d30000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x12d30000 0x30>; + interrupts = <0 69 0>; + }; + + spi at 12d40000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x12d40000 0x30>; + clock-frequency = <50000000>; + interrupts = <0 70 0>; + }; + + spi at 131a0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x131a0000 0x30>; + interrupts = <0 129 0>; + }; + + spi at 131b0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos-spi"; + reg = <0x131b0000 0x30>; + interrupts = <0 130 0>; + }; + + ehci at 12110000 { + compatible = "samsung,exynos-ehci"; + reg = <0x12110000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + + phy { + compatible = "samsung,exynos-usb-phy"; + reg = <0x12130000 0x100>; + }; + }; + + tmu at 10060000 { + compatible = "samsung,exynos-tmu"; + reg = <0x10060000 0x10000>; + }; + + fimd at 14400000 { + compatible = "samsung,exynos-fimd"; + reg = <0x14400000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + }; + + dp at 145b0000 { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + }; + + xhci0: xhci at 12000000 { + compatible = "samsung,exynos5250-xhci"; + reg = <0x12000000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + + phy { + compatible = "samsung,exynos5250-usb3-phy"; + reg = <0x12100000 0x100>; + }; + }; + + mmc at 12200000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + }; + + mmc at 12210000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12210000 0x1000>; + interrupts = <0 76 0>; + }; + + mmc at 12220000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12220000 0x1000>; + interrupts = <0 77 0>; + }; + + mmc at 12230000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12230000 0x1000>; + interrupts = <0 78 0>; + }; + + serial at 12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 51 0>; + id = <0>; + }; + + serial at 12C10000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C10000 0x100>; + interrupts = <0 52 0>; + id = <1>; + }; + + serial at 12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C20000 0x100>; + interrupts = <0 53 0>; + id = <2>; + }; + + serial at 12C30000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C30000 0x100>; + interrupts = <0 54 0>; + id = <3>; + }; + + gpio: gpio { + }; +};
arch/arm/dts/exynos5250.dtsi +4 -192
209 lines not on this page · raw message
arch/arm/dts/exynos5420.dtsi new file +70 -0
70 lines not on this page · raw message
board/samsung/dts/exynos5420-smdk5420.dts new file +169 -0
169 lines not on this page · raw message
Signature · 1 line
1.7.12.4
PATCH v8 8/9 Config: Add initial config for SMDK5420
In reply to Rajeshwari S ShindeAdding initial config for SMDK5420 to build and boot U-Boot over Exynos based SMDK5420.
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None
Chnages in V7:
- Corrected the coding style nits.
Changes in V8:
- None
include/configs/exynos5-dt.h | 300 +++++++++++++++++++++++++++++++++++++ include/configs/exynos5250-dt.h | 319 +--------------------------------------- include/configs/smdk5420.h | 49 ++++++ 3 files changed, 357 insertions(+), 311 deletions(-) create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h
include/configs/exynos5-dt.h new file +300 -0
@@ -0,0 +1,300 @@ +/* +* Copyright (C) 2013 Samsung Electronics +* +* Configuration settings for the SAMSUNG EXYNOS5 board. +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_SAMSUNG /* in a SAMSUNG core */ +#define CONFIG_S5P /* S5P Family */ +#define CONFIG_EXYNOS5 /* which is in a Exynos5 Family */ + +#include <asm/arch/cpu.h> /* get chip and board defs */ + +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_COMMON +#define CONFIG_ARCH_EARLY_INIT_R +#define CONFIG_EXYNOS_SPL + +/* Enable fdt support for Exynos5250 */ +#define CONFIG_OF_CONTROL +#define CONFIG_OF_SEPARATE + +/* Allow tracing to be enabled */ +#define CONFIG_TRACE +#define CONFIG_CMD_TRACE +#define CONFIG_TRACE_BUFFER_SIZE (16 << 20) +#define CONFIG_TRACE_EARLY_SIZE (8 << 20) +#define CONFIG_TRACE_EARLY +#define CONFIG_TRACE_EARLY_ADDR 0x50000000 + +/* Keep L2 Cache Disabled */ +#define CONFIG_SYS_DCACHE_OFF + +/* Enable ACE acceleration for SHA1 and SHA256 */ +#define CONFIG_EXYNOS_ACE_SHA +#define CONFIG_SHA_HW_ACCEL + +/* input clock of PLL: SMDK5250 has 24MHz input clock */ +#define CONFIG_SYS_CLK_FREQ 24000000 + +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_CMDLINE_TAG +#define CONFIG_INITRD_TAG +#define CONFIG_CMDLINE_EDITING + +/* Power Down Modes */ +#define S5P_CHECK_SLEEP 0x00000BAD +#define S5P_CHECK_DIDLE 0xBAD00000 +#define S5P_CHECK_LPA 0xABAD0000 + +/* Offset for inform registers */ +#define INFORM0_OFFSET 0x800 +#define INFORM1_OFFSET 0x804 +#define INFORM2_OFFSET 0x808 +#define INFORM3_OFFSET 0x80c + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20)) + +/* select serial console configuration */ +#define CONFIG_BAUDRATE 115200 +#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 +#define CONFIG_SILENT_CONSOLE + +/* Enable keyboard */ +#define CONFIG_CROS_EC /* CROS_EC protocol */ +#define CONFIG_CROS_EC_SPI /* Support CROS_EC over SPI */ +#define CONFIG_CROS_EC_I2C /* Support CROS_EC over I2C */ +#define CONFIG_CROS_EC_KEYB /* CROS_EC keyboard input */ +#define CONFIG_CMD_CROS_EC +#define CONFIG_KEYBOARD + +/* Console configuration */ +#define CONFIG_CONSOLE_MUX +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define EXYNOS_DEVICE_SETTINGS \ + "stdin=serial,cros-ec-keyb\0" \ + "stdout=serial,lcd\0" \ + "stderr=serial,lcd\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + EXYNOS_DEVICE_SETTINGS + +/* SD/MMC configuration */ +#define CONFIG_GENERIC_MMC +#define CONFIG_MMC +#define CONFIG_SDHCI +#define CONFIG_S5P_SDHCI +#define CONFIG_DWMMC +#define CONFIG_EXYNOS_DWMMC +#define CONFIG_SUPPORT_EMMC_BOOT + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* PWM */ +#define CONFIG_PWM + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Command definition*/ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_ELF +#define CONFIG_CMD_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_NET +#define CONFIG_CMD_HASH + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK + +/* Thermal Management Unit */ +#define CONFIG_EXYNOS_TMU +#define CONFIG_CMD_DTT +#define CONFIG_TMU_CMD_DTT + +/* USB */ +#define CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_EXYNOS +#define CONFIG_USB_STORAGE + +/* USB boot mode */ +#define CONFIG_USB_BOOTING +#define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070 +#define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002 +#define EXYNOS_IRAM_SECONDARY_BASE 0x02020018 + +/* TPM */ +#define CONFIG_TPM +#define CONFIG_CMD_TPM +#define CONFIG_TPM_TIS_I2C +#define CONFIG_TPM_TIS_I2C_BUS_NUMBER 3 +#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20 + +/* MMC SPL */ +#define CONFIG_SPL +#define COPY_BL2_FNPTR_ADDR 0x02020030 + +#define CONFIG_SPL_LIBCOMMON_SUPPORT + +/* specific .lds file */ +#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds" +#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024) + + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE 384/* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) + +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_RD_LVL + +#define CONFIG_NR_DRAM_BANKS 8 +#define SDRAM_BANK_SIZE (256UL << 20UL)/* 256 MB */ +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE +#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE) +#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH +#undef CONFIG_CMD_IMLS + +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_SECURE_BL1_ONLY + +/* Secure FW size configuration */ +#ifdef CONFIG_SECURE_BL1_ONLY +#define CONFIG_SEC_FW_SIZE (8 << 10)/* 8KB */ +#else +#define CONFIG_SEC_FW_SIZE 0 +#endif + +/* Configuration of BL1, BL2, ENV Blocks on mmc */ +#define CONFIG_RES_BLOCK_SIZE (512) +#define CONFIG_BL1_SIZE (16 << 10)/*16 K reserved for BL1*/ +#define CONFIG_BL2_SIZE (512UL << 10UL)/* 512 KB */ +#define CONFIG_ENV_SIZE (16 << 10)/* 16 KB */ + +#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE) +#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE) +#define CONFIG_ENV_OFFSET (CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE) + +/* U-boot copy size from boot Media to DRAM.*/ +#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512) +#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512) + +#define CONFIG_SPI_BOOTING +#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058 +#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) + +#define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION +#define CONFIG_CMD_PART +#define CONFIG_PARTITION_UUIDS + +/* I2C */ +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_HARD_I2C +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C_SPEED 100000/* 100 Kbps */ +#define CONFIG_DRIVER_S3C24X0_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_I2C_EDID + +/* SPI */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_SPI_FLASH + +#ifdef CONFIG_SPI_FLASH +#define CONFIG_EXYNOS_SPI +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SPI_FLASH_GIGADEVICE +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define EXYNOS5_SPI_NUM_CONTROLLERS 5 +#endif + +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 +#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE +#define CONFIG_ENV_SPI_BUS 1 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 +#endif + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C + +/* Ethernet Controllor Driver */ +#ifdef CONFIG_CMD_NET +#define CONFIG_SMC911X +#define CONFIG_SMC911X_BASE 0x5000000 +#define CONFIG_SMC911X_16_BIT +#define CONFIG_ENV_SROM_BANK 1 +#endif /*CONFIG_CMD_NET*/ + +/* Enable PXE Support */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_PXE +#define CONFIG_MENU +#endif + +/* Enable devicetree support */ +#define CONFIG_OF_LIBFDT + +/* SHA hashing */ +#define CONFIG_CMD_HASH +#define CONFIG_HASH_VERIFY +#define CONFIG_SHA1 +#define CONFIG_SHA256 + +/* Enable Time Command */ +#define CONFIG_CMD_TIME + +#define CONFIG_CMD_BOOTZ + +#endif /* __CONFIG_H */
include/configs/exynos5250-dt.h +8 -311
360 lines not on this page · raw message
include/configs/smdk5420.h new file +49 -0
49 lines not on this page · raw message
Signature · 1 line
1.7.12.4
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v8 8/9 Config: Add initial config for SMDK5420
ping.
-------- Original Message --------
Subject: Re: [PATCH 8/9 v8] Config: Add initial config for SMDK5420
Date: Thu, 21 Nov 2013 16:32:32 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com
Dear Rajeshwari,
Quoted 232 lines · Rajeshwari S Shinde
Adding initial config for SMDK5420 to build and boot U-Boot over Exynos based SMDK5420.
Signed-off-by Rajeshwari S Shinde <[email protected]>Signed-off-by Akshay Saraswat <[email protected]>Acked-by Simon Glass <[email protected]>---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a commonexynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None
Chnages in V7:
- Corrected the coding style nits.
Changes in V8:
- Noneinclude/configs/exynos5-dt.h | 300 +++++++++++++++++++++++++++++++++++++ include/configs/exynos5250-dt.h | 319 +--------------------------------------- include/configs/smdk5420.h | 49 ++++++ 3 files changed, 357 insertions(+), 311 deletions(-) create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.hinclude/configs/exynos5-dt.h new file +198
-0@@ -0,0 +1,300 @@ +/* +* Copyright (C) 2013 Samsung Electronics +* +* Configuration settings for the SAMSUNG EXYNOS5 board. +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_SAMSUNG /* in a SAMSUNG core */ +#define CONFIG_S5P /* S5P Family */ +#define CONFIG_EXYNOS5 /* which is in a Exynos5 Family */ + +#include <asm/arch/cpu.h> /* get chip and board defs */ + +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_COMMON +#define CONFIG_ARCH_EARLY_INIT_R +#define CONFIG_EXYNOS_SPL + +/* Enable fdt support for Exynos5250 */ +#define CONFIG_OF_CONTROL +#define CONFIG_OF_SEPARATE + +/* Allow tracing to be enabled */ +#define CONFIG_TRACE +#define CONFIG_CMD_TRACE +#define CONFIG_TRACE_BUFFER_SIZE (16 << 20) +#define CONFIG_TRACE_EARLY_SIZE (8 << 20) +#define CONFIG_TRACE_EARLY +#define CONFIG_TRACE_EARLY_ADDR 0x50000000 + +/* Keep L2 Cache Disabled */ +#define CONFIG_SYS_DCACHE_OFF + +/* Enable ACE acceleration for SHA1 and SHA256 */ +#define CONFIG_EXYNOS_ACE_SHA +#define CONFIG_SHA_HW_ACCEL + +/* input clock of PLL: SMDK5250 has 24MHz input clock */ +#define CONFIG_SYS_CLK_FREQ 24000000 + +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_CMDLINE_TAG +#define CONFIG_INITRD_TAG +#define CONFIG_CMDLINE_EDITING + +/* Power Down Modes */ +#define S5P_CHECK_SLEEP 0x00000BAD +#define S5P_CHECK_DIDLE 0xBAD00000 +#define S5P_CHECK_LPA 0xABAD0000 + +/* Offset for inform registers */ +#define INFORM0_OFFSET 0x800 +#define INFORM1_OFFSET 0x804 +#define INFORM2_OFFSET 0x808 +#define INFORM3_OFFSET 0x80c + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20)) + +/* select serial console configuration */ +#define CONFIG_BAUDRATE 115200 +#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 +#define CONFIG_SILENT_CONSOLE + +/* Enable keyboard */ +#define CONFIG_CROS_EC /* CROS_EC protocol */ +#define CONFIG_CROS_EC_SPI /* Support CROS_EC over SPI */ +#define CONFIG_CROS_EC_I2C /* Support CROS_EC over I2C */ +#define CONFIG_CROS_EC_KEYB /* CROS_EC keyboard input */ +#define CONFIG_CMD_CROS_EC +#define CONFIG_KEYBOARD + +/* Console configuration */ +#define CONFIG_CONSOLE_MUX +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define EXYNOS_DEVICE_SETTINGS \ + "stdin=serial,cros-ec-keyb\0" \ + "stdout=serial,lcd\0" \ + "stderr=serial,lcd\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + EXYNOS_DEVICE_SETTINGS + +/* SD/MMC configuration */ +#define CONFIG_GENERIC_MMC +#define CONFIG_MMC +#define CONFIG_SDHCI +#define CONFIG_S5P_SDHCI +#define CONFIG_DWMMC +#define CONFIG_EXYNOS_DWMMC +#define CONFIG_SUPPORT_EMMC_BOOT + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* PWM */ +#define CONFIG_PWM + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Command definition*/ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_ELF +#define CONFIG_CMD_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_NET +#define CONFIG_CMD_HASH + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK + +/* Thermal Management Unit */ +#define CONFIG_EXYNOS_TMU +#define CONFIG_CMD_DTT +#define CONFIG_TMU_CMD_DTT + +/* USB */ +#define CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_EXYNOS +#define CONFIG_USB_STORAGE + +/* USB boot mode */ +#define CONFIG_USB_BOOTING +#define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070 +#define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002 +#define EXYNOS_IRAM_SECONDARY_BASE 0x02020018 + +/* TPM */ +#define CONFIG_TPM +#define CONFIG_CMD_TPM +#define CONFIG_TPM_TIS_I2C +#define CONFIG_TPM_TIS_I2C_BUS_NUMBER 3 +#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20 + +/* MMC SPL */ +#define CONFIG_SPL +#define COPY_BL2_FNPTR_ADDR 0x02020030 + +#define CONFIG_SPL_LIBCOMMON_SUPPORT + +/* specific .lds file */ +#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds" +#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024) + + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE 384/* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) + +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_RD_LVL + +#define CONFIG_NR_DRAM_BANKS 8 +#define SDRAM_BANK_SIZE (256UL << 20UL)/* 256 MB */ +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE +#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE) +#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 + +/* FLASH and environment organization */
include/configs/exynos5-dt.h line 208
Quoted 10 lines
include/configs/exynos5-dt.h new file +10
-0+#define CONFIG_SYS_NO_FLASH +#undef CONFIG_CMD_IMLS + +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_SECURE_BL1_ONLY + +/* Secure FW size configuration */ +#ifdef CONFIG_SECURE_BL1_ONLY +#define CONFIG_SEC_FW_SIZE (8 << 10)/* 8KB */
please use space.
include/configs/exynos5-dt.h line 210
Quoted 2 lines
include/configs/exynos5-dt.h new file +2
-0+#else +#define CONFIG_SEC_FW_SIZE 0
ditto.
Quoted 504 lines
include/configs/exynos5-dt.h new file +90
-0+#endif + +/* Configuration of BL1, BL2, ENV Blocks on mmc */ +#define CONFIG_RES_BLOCK_SIZE (512) +#define CONFIG_BL1_SIZE (16 << 10)/*16 K reserved for BL1*/ +#define CONFIG_BL2_SIZE (512UL << 10UL)/* 512 KB */ +#define CONFIG_ENV_SIZE (16 << 10)/* 16 KB */ + +#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE) +#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE) +#define CONFIG_ENV_OFFSET (CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE) + +/* U-boot copy size from boot Media to DRAM.*/ +#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512) +#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512) + +#define CONFIG_SPI_BOOTING +#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058 +#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) + +#define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION +#define CONFIG_CMD_PART +#define CONFIG_PARTITION_UUIDS + +/* I2C */ +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_HARD_I2C +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C_SPEED 100000/* 100 Kbps */ +#define CONFIG_DRIVER_S3C24X0_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_I2C_EDID + +/* SPI */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_SPI_FLASH + +#ifdef CONFIG_SPI_FLASH +#define CONFIG_EXYNOS_SPI +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SPI_FLASH_GIGADEVICE +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define EXYNOS5_SPI_NUM_CONTROLLERS 5 +#endif + +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 +#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE +#define CONFIG_ENV_SPI_BUS 1 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 +#endif + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C + +/* Ethernet Controllor Driver */ +#ifdef CONFIG_CMD_NET +#define CONFIG_SMC911X +#define CONFIG_SMC911X_BASE 0x5000000 +#define CONFIG_SMC911X_16_BIT +#define CONFIG_ENV_SROM_BANK 1 +#endif /*CONFIG_CMD_NET*/ + +/* Enable PXE Support */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_PXE +#define CONFIG_MENU +#endif + +/* Enable devicetree support */ +#define CONFIG_OF_LIBFDT + +/* SHA hashing */ +#define CONFIG_CMD_HASH +#define CONFIG_HASH_VERIFY +#define CONFIG_SHA1 +#define CONFIG_SHA256 + +/* Enable Time Command */ +#define CONFIG_CMD_TIME + +#define CONFIG_CMD_BOOTZ + +#endif /* __CONFIG_H */ include/configs/exynos5250-dt.h +8
-311@@ -1,3 +1,4 @@ +/* * Copyright (C) 2012 Samsung Electronics * @@ -6,326 +7,35 @@* SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_SAMSUNG /* in a SAMSUNG core */ -#define CONFIG_S5P /* S5P Family */ -#define CONFIG_EXYNOS5 /* which is in a Exynos5 Family */ -#define CONFIG_EXYNOS5250 - -#include <asm/arch/cpu.h> /* get chip and board defs */ - -#define CONFIG_SYS_GENERIC_BOARD -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO -#define CONFIG_BOARD_COMMON -#define CONFIG_ARCH_EARLY_INIT_R +#ifndef __CONFIG_5250_H +#define __CONFIG_5250_H -/* Enable fdt support for Exynos5250 */ -#define CONFIG_OF_CONTROL -#define CONFIG_OF_SEPARATE +#include <configs/exynos5-dt.h> -/* Allow tracing to be enabled */ -#define CONFIG_TRACE -#define CONFIG_CMD_TRACE -#define CONFIG_TRACE_BUFFER_SIZE (16 << 20) -#define CONFIG_TRACE_EARLY_SIZE (8 << 20) -#define CONFIG_TRACE_EARLY -#define CONFIG_TRACE_EARLY_ADDR 0x50000000 - -/* Keep L2 Cache Disabled */ -#define CONFIG_SYS_DCACHE_OFF - -/* Enable ACE acceleration for SHA1 and SHA256 */ -#define CONFIG_EXYNOS_ACE_SHA -#define CONFIG_SHA_HW_ACCEL +#define CONFIG_EXYNOS5250 #define CONFIG_SYS_SDRAM_BASE 0x40000000#define CONFIG_SYS_TEXT_BASE 0x43E00000 -/* input clock of PLL: SMDK5250 has 24MHz input clock */ -#define CONFIG_SYS_CLK_FREQ 24000000 - -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_CMDLINE_TAG -#define CONFIG_INITRD_TAG -#define CONFIG_CMDLINE_EDITING -/* MACH_TYPE_SMDK5250 macro will be removed once added to mach-types */ #define MACH_TYPE_SMDK5250 3774#define CONFIG_MACH_TYPE MACH_TYPE_SMDK5250 -/* Power Down Modes */ -#define S5P_CHECK_SLEEP 0x00000BAD -#define S5P_CHECK_DIDLE 0xBAD00000 -#define S5P_CHECK_LPA 0xABAD0000 - -/* Offset for inform registers */ -#define INFORM0_OFFSET 0x800 -#define INFORM1_OFFSET 0x804 - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20)) - -/* select serial console configuration */ -#define CONFIG_BAUDRATE 115200 -#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 -#define CONFIG_SILENT_CONSOLE - -/* Enable keyboard */ -#define CONFIG_CROS_EC /* CROS_EC protocol */ -#define CONFIG_CROS_EC_SPI /* Support CROS_EC over SPI */ -#define CONFIG_CROS_EC_I2C /* Support CROS_EC over I2C */ -#define CONFIG_CROS_EC_KEYB /* CROS_EC keyboard input */ -#define CONFIG_CMD_CROS_EC -#define CONFIG_KEYBOARD - -/* Console configuration */ -#define CONFIG_CONSOLE_MUX -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define EXYNOS_DEVICE_SETTINGS \ - "stdin=serial,cros-ec-keyb\0" \ - "stdout=serial,lcd\0" \ - "stderr=serial,lcd\0" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - EXYNOS_DEVICE_SETTINGS - -/* SD/MMC configuration */ -#define CONFIG_GENERIC_MMC -#define CONFIG_MMC -#define CONFIG_SDHCI -#define CONFIG_S5P_SDHCI -#define CONFIG_DWMMC -#define CONFIG_EXYNOS_DWMMC -#define CONFIG_SUPPORT_EMMC_BOOT - - -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_SKIP_LOWLEVEL_INIT - -/* PWM */ -#define CONFIG_PWM - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command definition*/ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_ELF -#define CONFIG_CMD_MMC -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_NET -#define CONFIG_CMD_HASH - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK - -/* Thermal Management Unit */ -#define CONFIG_EXYNOS_TMU -#define CONFIG_CMD_DTT -#define CONFIG_TMU_CMD_DTT - -/* USB */ -#define CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_EXYNOS -#define CONFIG_USB_STORAGE - -/* USB boot mode */ -#define CONFIG_USB_BOOTING -#define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070 -#define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002 -#define EXYNOS_IRAM_SECONDARY_BASE 0x02020018 - -/* TPM */ -#define CONFIG_TPM -#define CONFIG_CMD_TPM -#define CONFIG_TPM_TIS_I2C -#define CONFIG_TPM_TIS_I2C_BUS_NUMBER 3 -#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20 - -/* MMC SPL */ -#define CONFIG_EXYNOS_SPL -#define CONFIG_SPL -#define COPY_BL2_FNPTR_ADDR 0x02020030 - -#define CONFIG_SPL_LIBCOMMON_SUPPORT - -/* specific .lds file */ -#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"#define CONFIG_SPL_TEXT_BASE 0x02023400 -#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024)#define CONFIG_BOOTCOMMAND "mmc read 40007000 451 2000; bootm 40007000" -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT "SMDK5250 # " -#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE 384/* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16/* max number of command args */ -#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE -/* memtest works on */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000) -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) - -#define CONFIG_SYS_HZ 1000 - -#define CONFIG_RD_LVL - -#define CONFIG_NR_DRAM_BANKS 8 -#define SDRAM_BANK_SIZE (256UL << 20UL)/* 256 MB */ -#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE -#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE -#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE) -#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE -#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE)) -#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE -#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE)) -#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE -#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE)) -#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE -#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE)) -#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE -#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE)) -#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE -#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE)) -#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE - -#define CONFIG_SYS_MONITOR_BASE 0x00000000 - -/* FLASH and environment organization */ -#define CONFIG_SYS_NO_FLASH -#undef CONFIG_CMD_IMLS -#define CONFIG_IDENT_STRING " for SMDK5250" - -#define CONFIG_SYS_MMC_ENV_DEV 0 - -#define CONFIG_SECURE_BL1_ONLY - -/* Secure FW size configuration */ -#ifdef CONFIG_SECURE_BL1_ONLY -#define CONFIG_SEC_FW_SIZE (8 << 10)/* 8KB */ -#else -#define CONFIG_SEC_FW_SIZE 0 -#endif - -/* Configuration of BL1, BL2, ENV Blocks on mmc */ -#define CONFIG_RES_BLOCK_SIZE (512) -#define CONFIG_BL1_SIZE (16 << 10)/*16 K reserved for BL1*/ -#define CONFIG_BL2_SIZE (512UL << 10UL)/* 512 KB */ -#define CONFIG_ENV_SIZE (16 << 10)/* 16 KB */ - -#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE) -#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE) -#define CONFIG_ENV_OFFSET (CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE) - -/* U-boot copy size from boot Media to DRAM.*/ -#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512) -#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512) - -#define CONFIG_SPI_BOOTING -#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058 -#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) - -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION -#define CONFIG_CMD_PART -#define CONFIG_PARTITION_UUIDS -#define CONFIG_IRAM_STACK 0x02050000#define CONFIG_SYS_INIT_SP_ADDR CONFIG_IRAM_STACK -/* I2C */ -#define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_HARD_I2C -#define CONFIG_CMD_I2C -#define CONFIG_SYS_I2C_SPEED 100000/* 100 Kbps */ -#define CONFIG_DRIVER_S3C24X0_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_MAX_I2C_NUM 8 -#define CONFIG_SYS_I2C_SLAVE 0x0 -#define CONFIG_I2C_EDID -/* PMIC */ -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C #define CONFIG_PMIC_MAX77686 -/* SPI */ -#define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_SPI_FLASH - -#ifdef CONFIG_SPI_FLASH -#define CONFIG_EXYNOS_SPI -#define CONFIG_CMD_SF -#define CONFIG_CMD_SPI -#define CONFIG_SPI_FLASH_WINBOND -#define CONFIG_SPI_FLASH_GIGADEVICE -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 -#define CONFIG_SF_DEFAULT_SPEED 50000000 -#define EXYNOS5_SPI_NUM_CONTROLLERS 5 -#endif - -#ifdef CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_MODE SPI_MODE_0 -#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE -#define CONFIG_ENV_SPI_BUS 1 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 -#endif - -/* PMIC */ -#define CONFIG_POWER -#define CONFIG_POWER_I2C -#define CONFIG_POWER_MAX77686 - -/* SPI */ -#define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_SPI_FLASH - -#ifdef CONFIG_SPI_FLASH -#define CONFIG_EXYNOS_SPI -#define CONFIG_CMD_SF -#define CONFIG_CMD_SPI -#define CONFIG_SPI_FLASH_WINBOND -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 -#define CONFIG_SF_DEFAULT_SPEED 50000000 -#define EXYNOS5_SPI_NUM_CONTROLLERS 5 -#endif - -#ifdef CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_MODE SPI_MODE_0 -#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE -#define CONFIG_ENV_SPI_BUS 1 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 -#endif - -/* Ethernet Controllor Driver */ -#ifdef CONFIG_CMD_NET -#define CONFIG_SMC911X -#define CONFIG_SMC911X_BASE 0x5000000 -#define CONFIG_SMC911X_16_BIT -#define CONFIG_ENV_SROM_BANK 1 -#endif /*CONFIG_CMD_NET*/ - -/* Enable PXE Support */ -#ifdef CONFIG_CMD_NET -#define CONFIG_CMD_PXE -#define CONFIG_MENU -#endif +/* I2C */ +#define CONFIG_MAX_I2C_NUM 8/* Sound */ #define CONFIG_CMD_SOUND @@ -336,15 +46,6 @@#define CONFIG_SOUND_WM8994 #endif -/* Enable devicetree support */ -#define CONFIG_OF_LIBFDT - -/* SHA hashing */ -#define CONFIG_CMD_HASH -#define CONFIG_HASH_VERIFY -#define CONFIG_SHA1 -#define CONFIG_SHA256 -/* Display */ #define CONFIG_LCD #ifdef CONFIG_LCD @@ -354,8 +55,4 @@#define LCD_YRES 1600#define LCD_BPP LCD_COLOR16#endif - -/* Enable Time Command */ -#define CONFIG_CMD_TIME - -#endif /* __CONFIG_H */ +#endif /* __CONFIG_5250_H */ include/configs/smdk5420.h new file +39
-0@@ -0,0 +1,49 @@ +/* +* Copyright (C) 2013 Samsung Electronics +* +* Configuration settings for the SAMSUNG EXYNOS5420 board. +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __CONFIG_5420_H +#define __CONFIG_5420_H + +#include <configs/exynos5-dt.h> + +#define CONFIG_EXYNOS5420 /* which is in a Exynos5 Family */ +#define CONFIG_SMDK5420 /* which is in a SMDK5420 */ + +#undef CONFIG_DEFAULT_DEVICE_TREE +#define CONFIG_DEFAULT_DEVICE_TREE exynos5420-smdk5420 + +#define CONFIG_ARCH_DEVICE_TREE exynos5420 + +#define CONFIG_SYS_SDRAM_BASE 0x20000000 +#define CONFIG_SYS_TEXT_BASE 0x23E00000 + +#define CONFIG_BOARD_REV_GPIO_COUNT 2 + +/* MACH_TYPE_SMDK5420 macro will be removed once added to mach-types */ +#define MACH_TYPE_SMDK5420 8002/* Temporary number */ +#define CONFIG_MACH_TYPE MACH_TYPE_SMDK5420 + +/* select serial console configuration */ +#define CONFIG_SERIAL3 /* use SERIAL 3 */ + +#define CONFIG_SPL_TEXT_BASE 0x02024400 +#define CONFIG_BOOTCOMMAND "mmc read 20007000 451 2000; bootm 20007000" + +#define CONFIG_SYS_PROMPT "SMDK5420 # " +#define CONFIG_IDENT_STRING " for SMDK5420" +
include/configs/smdk5420.h line 49
Quoted 10 lines
include/configs/smdk5420.h new file +10
-0+#define CONFIG_IRAM_TOP 0x02074000 +/* +* Put the initial stack pointer 1KB below this to allow room for the +* SPL marker. This value is arbitrary, but gd_t is placed starting here. +*/ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_IRAM_TOP - 0x800) + +#define CONFIG_MAX_I2C_NUM 11 + +#endif /* __CONFIG_5420_H */
Thanks,
Minkyu Kang.
PATCH v8 9/9 SPL: EXYNOS: Prepare for variable size SPL support
In reply to Rajeshwari S ShindeWhen variable size SPL is used, the BL1 expects the SPL to be encapsulated differently: instead of putting the checksum at a fixed offset in the SPL blob, prepend the blob with a header including the size and the checksum.
The enhancements include
- adding a command line option, '--vs' to indicate the need for the variable size encapsulation
- padding the fixed size encapsulated blob with 0xff instead of random memory contents
- do not silently truncate the input file, report error instead
- no need to explicitly closing files/freeing memory, this all happens on exit; removing cleanups it makes code clearer
- profuse commenting
- modify Makefile to allow enabling the new feature per board
---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None.
Changes in V7:
- None.
Changes in V8:
- None
include/configs/smdk5420.h | 7 ++ spl/Makefile | 7 +- tools/mkexynosspl.c | 167 +++++++++++++++++++++++++++++++++------------ 3 files changed, 137 insertions(+), 44 deletions(-)
include/configs/smdk5420.h +7 -0
@@ -19,6 +19,8 @@#define CONFIG_ARCH_DEVICE_TREE exynos5420 +#define CONFIG_VAR_SIZE_SPL +#define CONFIG_SYS_SDRAM_BASE 0x20000000#define CONFIG_SYS_TEXT_BASE 0x23E00000
@@ -31,7 +33,12 @@/* select serial console configuration */ #define CONFIG_SERIAL3 /* use SERIAL 3 */ +#ifdef CONFIG_VAR_SIZE_SPL +#define CONFIG_SPL_TEXT_BASE 0x02024410 +#else #define CONFIG_SPL_TEXT_BASE 0x02024400 +#endif +#define CONFIG_BOOTCOMMAND "mmc read 20007000 451 2000; bootm 20007000"#define CONFIG_SYS_PROMPT "SMDK5420 # "
spl/Makefile +6 -1
@@ -184,8 +184,13 @@ endif all: $(ALL-y) ifdef CONFIG_SAMSUNG +ifdef CONFIG_VAR_SIZE_SPL +VAR_SIZE_PARAM = --vs +else +VAR_SIZE_PARAM = +endif $(obj)$(BOARD)-spl.bin: $(obj)u-boot-spl.bin - $(OBJTREE)/tools/mk$(BOARD)spl \ + $(OBJTREE)/tools/mk$(BOARD)spl $(VAR_SIZE_PARAM) \ $(obj)u-boot-spl.bin $(obj)$(BOARD)-spl.bin endif
tools/mkexynosspl.c +124 -43
217 lines not on this page · raw message
Signature · 1 line
1.7.12.4
v8 cover EXYNOS5420: Add SMDK5420 board support
In reply to Rajeshwari S ShindeHi Minkyu Kang.
Please do let me know if any comments or can we get this merged?
Quoted 100 lines · Rajeshwari S Shinde
This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.
Changes in V2:
- Corrected a compilation issue for SMDK5420.Changes in V3:
- Add patch to support variable size SPL support
- Add patch to disable SMU for eMMC.Changes in V4:
- Added check for MAX77686 pmic compilation.
- Added correct calculation of gpio based addresses.
- Rebased on the latest u-boot code.
- Removed patches for UART and TZPC changes as they were not needed.
- Added flag to disable SMU for eMMC.Changes in V5:
- Moved functionsboard_mmc_initandboard_eth_inittocommon/board.cin case of device tree support.Changes in V6:
- Rebased on the latest mainline branch.
- Moved the definitions for SMU toarch/armdwmmc.hChanges in V7:
- Removed below patch as it is already merged "DWMMC: SMDK5420: Disable SMU for eMMC"
- Corrected the multi line comments and removal of blank spaces and lines.
- Corrected the license.Changes in V8:
- corrected the if loops with if conditions ofpro_idandcpu_id.Rajeshwari S Shinde (9):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL supportarch/arm/cpu/armv7/exynos/clock.c | 258 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 10 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 421 +++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 738 +++++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 260 ++++++++- arch/arm/dts/exynos5.dtsi | 198 +++++++ arch/arm/dts/exynos5250.dtsi | 196 +------ arch/arm/dts/exynos5420.dtsi | 70 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 51 +- arch/arm/include/asm/arch-exynos/dmc.h | 123 +++-- arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++- arch/arm/include/asm/arch-exynos/periph.h | 3 + board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 407 ++++++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 ++++++ board/samsung/smdk5250/exynos5-dt.c | 361 +----------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 34 ++ board/samsung/smdk5420/smdk5420.c | 159 ++++++ board/samsung/smdk5420/smdk5420_spl.c | 52 ++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5-dt.h | 300 ++++++++++ include/configs/exynos5250-dt.h | 316 +---------- include/configs/smdk5420.h | 56 ++ spl/Makefile | 7 +- tools/Makefile | 3 +- tools/mkexynosspl.c | 167 ++++-- 33 files changed, 4227 insertions(+), 1344 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h--
1.7.12.4_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 2 lines
Regards, Rajeshwari Shinde
v8 cover EXYNOS5420: Add SMDK5420 board support
Quoted 109 lines · Rajeshwari Birje
Hi Minkyu Kang.
Please do let me know if any comments or can we get this merged?
Quoted 100 lines · Rajeshwari S Shinde
This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.
Changes in V2:
- Corrected a compilation issue for SMDK5420.Changes in V3:
- Add patch to support variable size SPL support
- Add patch to disable SMU for eMMC.Changes in V4:
- Added check for MAX77686 pmic compilation.
- Added correct calculation of gpio based addresses.
- Rebased on the latest u-boot code.
- Removed patches for UART and TZPC changes as they were not needed.
- Added flag to disable SMU for eMMC.Changes in V5:
- Moved functionsboard_mmc_initandboard_eth_inittocommon/board.cin case of device tree support.Changes in V6:
- Rebased on the latest mainline branch.
- Moved the definitions for SMU toarch/armdwmmc.hChanges in V7:
- Removed below patch as it is already merged "DWMMC: SMDK5420: Disable SMU for eMMC"
- Corrected the multi line comments and removal of blank spaces and lines.
- Corrected the license.Changes in V8:
- corrected the if loops with if conditions ofpro_idandcpu_id.Rajeshwari S Shinde (9):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL supportarch/arm/cpu/armv7/exynos/clock.c | 258 ++++++++- arch/arm/cpu/armv7/exynos/clock_init.h | 17 + arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++- arch/arm/cpu/armv7/exynos/dmc_common.c | 10 +- arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 421 +++++++++++++- arch/arm/cpu/armv7/exynos/exynos5_setup.h | 738 +++++++++++++++++++------ arch/arm/cpu/armv7/exynos/pinmux.c | 260 ++++++++- arch/arm/dts/exynos5.dtsi | 198 +++++++ arch/arm/dts/exynos5250.dtsi | 196 +------ arch/arm/dts/exynos5420.dtsi | 70 +++ arch/arm/include/asm/arch-exynos/board.h | 17 + arch/arm/include/asm/arch-exynos/clk.h | 1 + arch/arm/include/asm/arch-exynos/clock.h | 494 +++++++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 51 +- arch/arm/include/asm/arch-exynos/dmc.h | 123 +++-- arch/arm/include/asm/arch-exynos/gpio.h | 143 ++++- arch/arm/include/asm/arch-exynos/periph.h | 3 + board/samsung/common/Makefile | 4 + board/samsung/common/board.c | 407 ++++++++++++++ board/samsung/dts/exynos5420-smdk5420.dts | 169 ++++++ board/samsung/smdk5250/exynos5-dt.c | 361 +----------- board/samsung/smdk5250/smdk5250.c | 182 +----- board/samsung/smdk5420/Makefile | 34 ++ board/samsung/smdk5420/smdk5420.c | 159 ++++++ board/samsung/smdk5420/smdk5420_spl.c | 52 ++ boards.cfg | 1 + include/configs/arndale.h | 1 + include/configs/exynos5-dt.h | 300 ++++++++++ include/configs/exynos5250-dt.h | 316 +---------- include/configs/smdk5420.h | 56 ++ spl/Makefile | 7 +- tools/Makefile | 3 +- tools/mkexynosspl.c | 167 ++++-- 33 files changed, 4227 insertions(+), 1344 deletions(-) create mode 100644 arch/arm/dts/exynos5.dtsi create mode 100644 arch/arm/dts/exynos5420.dtsi create mode 100644 arch/arm/include/asm/arch-exynos/board.h create mode 100644 board/samsung/common/board.c create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts create mode 100644 board/samsung/smdk5420/Makefile create mode 100644 board/samsung/smdk5420/smdk5420.c create mode 100644 board/samsung/smdk5420/smdk5420_spl.c create mode 100644 include/configs/exynos5-dt.h create mode 100644 include/configs/smdk5420.h--
1.7.12.4_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
I already sent comments on your patches. but, it does not reached at mailing list. I don't know why.
Anyway sorry, I'll resend comments.
Thanks,
Minkyu Kang.