ARM: shmobile: r8a7790/lager dts: Add DVFS parameters into cpu0 node for r8a7790
Subsystems (2)
PATCH v2 2/8 ARM: shmobile: r8a7790/lager dts: Add DVFS parameters into cpu0 node for r8a7790
From: Benoit Cousson <[email protected]>
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP table. Due to the lack of proper OPP definition, use an arbitrary safe value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this value since the clock transition latency is not the only parameter that will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage since the valid Vmin voltage is not documented in the HW spec.
- clocks
phandle to the CPU clock source. This clock source is used for all the 4 CortexA15 located inside the same cluster.
---
Changes since version 1:
- changed "Signed-off-by" and "From" correctly.
- added the setting of VDD.
- changed the setting of OPPs for ES2.0
- fixed subject.
arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++ arch/arm/boot/dts/r8a7790.dtsi | 11 +++++++++++ 2 files changed, 15 insertions(+)
arch/arm/boot/dts/r8a7790-lager.dts +4 -0
@@ -338,3 +338,7 @@ regulator-always-on; }; }; + +&cpu0 { + cpu0-supply = <&vdd_dvfs>; +};
arch/arm/boot/dts/r8a7790.dtsi +11 -0
@@ -44,6 +44,17 @@ compatible = "arm,cortex-a15"; reg = <0>; clock-frequency = <1300000000>; + voltage-tolerance = <1>; /* 1% */ + clocks = <&cpg_clocks R8A7790_CLK_Z>; + clock-latency = <300000>; /* 300 us */ + + /* kHz - uV - OPPs unknown yet */ + operating-points = <1400000 1000000>, + <1225000 1000000>, + <1050000 1000000>, + < 875000 1000000>, + < 700000 1000000>, + < 350000 1000000>; }; cpu1: cpu@1 {
Signature · 1 line
1.7.9.5
Quoted 21 lines · Gaku Inami
From: Benoit Cousson <[email protected]>
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP table. Due to the lack of proper OPP definition, use an arbitrary safe value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this value since the clock transition latency is not the only parameter that will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage since the valid Vmin voltage is not documented in the HW spec.
- clocks
phandle to the CPU clock source. This clock source is used for all the 4 CortexA15 located inside the same cluster.
Quoted 3 lines
Signed-off-by Benoit Cousson <[email protected]>[[email protected]: Change the setting of OPPs for ES2.0]Signed-off-by Gaku Inami <[email protected]>
Thanks, I have queued this up with Magnus's ack.
Quoted 49 lines
---
Changes since version 1:
- changed "Signed-off-by" and "From" correctly.
- added the setting of VDD.
- changed the setting of OPPs for ES2.0
- fixed subject.arch/arm/boot/dts/r8a7790-lager.dts | 4 ++++ arch/arm/boot/dts/r8a7790.dtsi | 11 +++++++++++ 2 files changed, 15 insertions(+)arch/arm/boot/dts/r8a7790-lager.dts +4
-0@@ -338,3 +338,7 @@ regulator-always-on; }; }; + +&cpu0 { + cpu0-supply = <&vdd_dvfs>; +};arch/arm/boot/dts/r8a7790.dtsi +11
-0@@ -44,6 +44,17 @@ compatible = "arm,cortex-a15"; reg = <0>; clock-frequency = <1300000000>; + voltage-tolerance = <1>; /* 1% */ + clocks = <&cpg_clocks R8A7790_CLK_Z>; + clock-latency = <300000>; /* 300 us */ + + /* kHz - uV - OPPs unknown yet */ + operating-points = <1400000 1000000>, + <1225000 1000000>, + <1050000 1000000>, + < 875000 1000000>, + < 700000 1000000>, + < 350000 1000000>; }; cpu1: cpu@1 {Signature · 1 line
1.7.9.5