Skip to contentSkip to conversation

ARM: dts: Add DT changes for display on snow

PATCH New Ajay Kumar 3 participants 4 messages Sep 1, 2014 – Sep 13, 2014

Subsystems (2)
lore
Share & tools
lore

Ajay Kumar

author
#0 lore raw

PATCH v3 1/2 ARM: dts: Add DT changes for display on snow

Add DT nodes for ptn3460 bridge chip and panel.
Add backlight enable pin and backlight power supply for pwm-backlight. Also add bridge phandle needed by dp to enable display on snow.

---
Changes since V1:
-- Remove "simple-panel" compatible string.
-- Use GPIO_ACTIVE_HIGH instead of 0.
-- Change panel node naming from "panel-simple" to "panel".

Changes since V2:
-- Use proper compatible string: "auo,b116xw03"

 arch/arm/boot/dts/exynos5250-snow.dts |   41 ++++++++++++++++++---------------
 1 file changed, 22 insertions(+), 19 deletions(-)
arch/arm/boot/dts/exynos5250-snow.dts +22 -19
index f2b8c41..1ac9709 100644
@@ -9,6 +9,7 @@
 */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "exynos5250.dtsi"
 #include "exynos5250-cros-common.dtsi"
 
@@ -181,7 +182,7 @@
 					dcdc3 {
 						ti,enable-ext-control;
 					};
-					fet1 {
+					fet1: fet1 {
 						regulator-name = "vcd_led";
 						ti,overcurrent-wait = <3>;
 					};
@@ -204,7 +205,7 @@
 						regulator-always-on;
 						ti,overcurrent-wait = <3>;
 					};
-					fet6 {
+					fet6: fet6 {
 						regulator-name = "lcd_vdd";
 						ti,overcurrent-wait = <3>;
 					};
@@ -253,6 +254,15 @@
 			pinctrl-0 = <&max98095_en>;
 			pinctrl-names = "default";
 		};
+
+		ptn3460: lvds-bridge at 20 {
+			compatible = "nxp,ptn3460";
+			reg = <0x20>;
+			powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
+			edid-emulation = <5>;
+			panel = <&panel>;
+		};
 	};
 
 	i2s0: i2s at 03830000 {
@@ -300,11 +310,13 @@
 		vdd_pll-supply = <&ldo8_reg>;
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 0 1000000 0>;
 		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
 		default-brightness-level = <7>;
+		enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
+		power-supply = <&fet1>;
 		pinctrl-0 = <&pwm0_out>;
 		pinctrl-names = "default";
 	};
@@ -314,6 +326,12 @@
 		samsung,invert-vclk;
 	};
 
+	panel: panel {
+		compatible = "auo,b116xw03";
+		power-supply = <&fet6>;
+		backlight = <&backlight>;
+	};
+
 	dp-controller at 145B0000 {
 		status = "okay";
 		pinctrl-names = "default";
@@ -325,22 +343,7 @@
 		samsung,link-rate = <0x0a>;
 		samsung,lane-count = <2>;
 		samsung,hpd-gpio = <&gpx0 7 0>;
-
-		display-timings {
-			native-mode = <&timing1>;
-
-			timing1: timing at 1 {
-				clock-frequency = <70589280>;
-				hactive = <1366>;
-				vactive = <768>;
-				hfront-porch = <40>;
-				hback-porch = <40>;
-				hsync-len = <32>;
-				vback-porch = <10>;
-				vfront-porch = <12>;
-				vsync-len = <6>;
-			};
-		};
+		bridge = <&ptn3460>;
 	};
 };
 
Signature · 1 line
1.7.9.5
author
#1 lore raw

PATCH v3 2/2 ARM: dts: Add DT changes for display on peach_pit

Add DT nodes for ps8622 bridge chip and panel.
Add backlight power supply for pwm-backlight.
Also add bridge phandle needed by dp to enable display on peach_pit.

---
Changes since V1:
-- Remove "simple-panel" compatible string.
-- Use GPIO_ACTIVE_HIGH instead of 0.
-- Change panel node naming from "panel-simple" to "panel".

Changes since V2:
-- Use proper compatible string: "auo,b116xw03"

 arch/arm/boot/dts/exynos5420-peach-pit.dts |   36 +++++++++++++++-------------
 1 file changed, 19 insertions(+), 17 deletions(-)
arch/arm/boot/dts/exynos5420-peach-pit.dts +19 -17
index 228a6b1..1070a31 100644
@@ -30,11 +30,12 @@
 		i2c20 = "/spi at 12d40000/cros-ec at 0/i2c-tunnel";
 	};
 
-	backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 0 1000000 0>;
 		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
 		default-brightness-level = <7>;
+		power-supply = <&tps65090_fet1>;
 		pinctrl-0 = <&pwm0_out>;
 		pinctrl-names = "default";
 	};
@@ -100,6 +101,12 @@
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	panel: panel {
+		compatible = "auo,b116xw03";
+		power-supply = <&tps65090_fet6>;
+		backlight = <&backlight>;
+	};
 };
 
 &dp {
@@ -113,22 +120,7 @@
 	samsung,link-rate = <0x06>;
 	samsung,lane-count = <2>;
 	samsung,hpd-gpio = <&gpx2 6 0>;
-
-	display-timings {
-		native-mode = <&timing1>;
-
-		timing1: timing at 1 {
-			clock-frequency = <70589280>;
-			hactive = <1366>;
-			vactive = <768>;
-			hfront-porch = <40>;
-			hback-porch = <40>;
-			hsync-len = <32>;
-			vback-porch = <10>;
-			vfront-porch = <12>;
-			vsync-len = <6>;
-		};
-	};
+	bridge = <&ps8625>;
 };
 
 &fimd {
@@ -155,6 +147,16 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&max98090_irq>;
 	};
+
+	ps8625: lvds-bridge at 48 {
+		compatible = "parade,ps8625";
+		reg = <0x48>;
+		sleep-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpy7 7 GPIO_ACTIVE_HIGH>;
+		lane-count = <2>;
+		panel = <&panel>;
+		use-external-pwm;
+	};
 };
 
 &hsi2c_9 {
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH v3 1/2 ARM: dts: Add DT changes for display on snow

In reply to Ajay Kumar
Quoted 11 lines · Ajay Kumar

Add DT nodes for ptn3460 bridge chip and panel.
Add backlight enable pin and backlight power supply for pwm-backlight. Also add bridge phandle needed by dp to enable display on snow.

---
Changes since V1:
-- Remove "simple-panel" compatible string.
-- Use GPIO_ACTIVE_HIGH instead of 0.
-- Change panel node naming from "panel-simple" to "panel".

Quoted 6 lines

Changes since V2:
-- Use proper compatible string: "auo,b116xw03"

  arch/arm/boot/dts/exynos5250-snow.dts |   41 ++++++++++++++++++---------------
  1 file changed, 22 insertions(+), 19 deletions(-)

Applied this and 2nd one.

BTW, I resolved conflict when I applied. Please check my tree and then if any problems, please let me know.

Thanks,
Kukjin

#3 lore raw

PATCH v3 1/2 ARM: dts: Add DT changes for display on snow

Hi Kukjin,

Quoted 16 lines · Kukjin Kim
Quoted 15 lines · Ajay Kumar

Add DT nodes for ptn3460 bridge chip and panel.
Add backlight enable pin and backlight power supply for pwm-backlight. Also add bridge phandle needed by dp to enable display on snow.

---
Changes since V1:
-- Remove "simple-panel" compatible string.
-- Use GPIO_ACTIVE_HIGH instead of 0.
-- Change panel node naming from "panel-simple" to "panel".

Changes since V2:
-- Use proper compatible string: "auo,b116xw03"

Quoted 8 lines
Quoted 4 lines
  arch/arm/boot/dts/exynos5250-snow.dts |   41
++++++++++++++++++---------------
  1 file changed, 22 insertions(+), 19 deletions(-)

Applied this and 2nd one.

BTW, I resolved conflict when I applied. Please check my tree and then if any problems, please let me know.

This patchset has dependency on driver patches. But, no harm merging it since DT bindings are almost agreed.

The below patch should be merged ASAP. Because, driver changes are already in for this patch:
https://www.mail-archive.com/linux-samsung-soc at vger.kernel.org/msg35182.html

Ajay