ARM: BCM5301X: Add DT for Luxul XWC-1000
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH 1/1 ARM: BCM5301X: Add DT for Luxul XWC-1000
Hi Dan,
This looks ok to me.
I haven't noticed before, but you should also send patches for BCM5301X to the linux arm mailing list at linux-arm-kernel at lists.infradead.org . Could you please send this patch one more time and then in addition to the arm mailing list.
Hauke
Quoted 6 lines · Dan Haab
From: Dan Haab <[email protected]>
Luxul XWC-1000 is a controller device based on BCM4708 SoC. The only unusual thing in its DTS file is "ubi" partition on NAND flash.
Signed-off-by Dan Haab <[email protected]>
Signed-off-by Hauke Mehrtens <[email protected]>
Quoted 90 lines
---
Hello Hauke,We believe you are going to collect BCM5301X DTS changes for 3.20. Please consider following patch.
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts | 60 ++++++++++++++++++++++++++++ 2 files changed, 61 insertions(+) create mode 100644 arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dtsarch/arm/boot/dts/Makefile +1
-0@@ -57,6 +57,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b-plus.dtb dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4708-buffalo-wzr-1750dhp.dtb \ + bcm4708-luxul-xwc-1000.dtb \ bcm4708-netgear-r6250.dtb \ bcm4708-netgear-r6300-v2.dtb \ bcm47081-asus-rt-n18u.dtb \arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts new file +60
-0@@ -0,0 +1,60 @@ +/* + * Broadcom BCM470X / BCM5301X ARM platform code. + * DTS for Luxul XWC-1000 + * + * Copyright 2014 Luxul Inc. + * + * Licensed under the GNU/GPL. See COPYING for details. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" + +/ { + compatible = "luxul,xwc-1000", "brcm,bcm4708"; + model = "Luxul XWC-1000 (BCM4708)"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; + + axi at 18000000 { + nand at 28000 { + reg = <0x00028000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + partition at 0 { + label = "ubi"; + reg = <0x00000000 0x08000000>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + status { + label = "bcm53xx:green:status"; + gpios = <&chipcommon 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "timer"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + restart { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>; + }; + }; +};