Skip to contentSkip to conversation

sigmadsp: adau1701: Version mismatch while loading firmware in 3.18.3

DISCUSSION Pascal Huerst 2 participants 3 messages Jan 28, 2015

lore
Share & tools
lore
#0 lore raw

Hello Lars-Peter,

i followed the instructions on:

http://wiki.analog.com/resources/tools-software/linux-software/sigmadsp_genfirmware

and built the firmware from my xml-file. But when the driver loads, I always get:

adau1701 2-0034: Failed to load firmware: Invalid version 2. Supported firmware versions: 1
adau1701 2-0034: Failed to load firmware
adau1701 2-0034: ASoC: can't set adau1701 hw params: -22

I have been using that .xml/.bin file in 3.14.13 for some time, but now in 3.18.3 I always get the version mismatch from above.

What am I doing wrong?

regards
pascal

#1 lore raw
Quoted 9 lines · Pascal Huerst

Hello Lars-Peter,

i followed the instructions on:

http://wiki.analog.com/resources/tools-software/linux-software/sigmadsp_genfirmware

and built the firmware from my xml-file. But when the driver loads, I always get:

Quoted 7 lines

adau1701 2-0034: Failed to load firmware: Invalid version 2. Supported firmware versions: 1
adau1701 2-0034: Failed to load firmware
adau1701 2-0034: ASoC: can't set adau1701 hw params: -22

I have been using that .xml/.bin file in 3.14.13 for some time, but now in 3.18.3 I always get the version mismatch from above.

Hi,

Are you sure that the you were previously using a v2 firmware file? v2 was not supported until recently and loading it with the v1 loader would just result in garbage being written to the device.

The patch[1] that adds support for v2 is pretty standalone and you should be able to backport it to v3.18.

- Lars

[1] http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/sound/soc/codecs/sigmadsp.c?id=a35daac77a0397d4f23b642d3dc0684682e56cc5

#2 lore raw
Quoted 16 lines · Lars-Peter Clausen
Quoted 15 lines · Pascal Huerst

Hello Lars-Peter,

i followed the instructions on:

http://wiki.analog.com/resources/tools-software/linux-software/sigmadsp_genfirmware

and built the firmware from my xml-file. But when the driver loads, I always get:

adau1701 2-0034: Failed to load firmware: Invalid version 2. Supported firmware versions: 1
adau1701 2-0034: Failed to load firmware
adau1701 2-0034: ASoC: can't set adau1701 hw params: -22

Quoted 8 lines
Quoted 2 lines

I have been using that .xml/.bin file in 3.14.13 for some time, but now in 3.18.3 I always get the version mismatch from above.

Hi,

Are you sure that the you were previously using a v2 firmware file? v2 was not supported until recently and loading it with the v1 loader would just result in garbage being written to the device.

I have been using the firmware file for more than a year without any problems on 3.14.23, so I assume it is v1. I don't know why the driver tells me it's v2, however. Maybe my tree is messed up.

If I port adau1701.{c,h} and sigmadsp.{c,h} from 3.14.23 to 3.18.3, it works. I think I have to look deeper into that...

Quoted 2 lines

The patch[1] that adds support for v2 is pretty standalone and you should be able to backport it to v3.18.

If I cherry-pick that in, the message is gone, but still, I don't have no output.

Quoted 2 lines

[1]
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/sound/soc/codecs/sigmadsp.c?id=a35daac77a0397d4f23b642d3dc0684682e56cc5