Skip to contentSkip to conversation

First QCA6174 firmware release

DISCUSSION Olaf Dreyer 3 participants 3 messages Feb 11, 2015 – Apr 27, 2015 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

I have a new Acer Aspire VN7-591 Laptop with a Qualcom Atheros QCNF344 wireless chip, which is shown by lspci as:

Qualcomm Atheros Device 003e (rev 20)
Subsystem: Foxconn International, Inc. Device e08e

I have installed the linux-next kernel from today 8:00 UTC.
I was able to load the ath10k_pci driver, but the driver complains about missing firmware.
I installed a firmware from here: https://github.com/kvalo/ath10k-firmware
under /lib/firmware/ath10k/QCA6174/hw2.1/
But also the card is not working.

The output from dmesg is:

[ 9360.538767] ath10k_pci 0000:07:00.0: pci irq msi interrupts 1
irq_mode 0 reset_mode 0
[ 9360.788588] ath10k_pci 0000:07:00.0: Direct firmware load for
ath10k/cal-pci-0000:07:00.0.bin failed with error -2
[ 9362.729118] ath10k_pci 0000:07:00.0: unable to write to the device
[ 9362.729120] ath10k_pci 0000:07:00.0: failed to download normal
firmware: -110
[ 9362.729121] ath10k_pci 0000:07:00.0: could not init core (-110)
[ 9362.729156] ath10k_pci 0000:07:00.0: could not probe fw (-110)

I would like to know, as Austin Hendrix wrote it at 8 Feb 14:12 2015 too, where can I find the firmware on the
internet / my Windows7 partition and how can I prepare the needed files.

Many thanks,

Olaf

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw
Quoted 2 lines · Olaf Dreyer <olaf <at> dreyero.de> writes:

I have a new Acer Aspire VN7-591 Laptop with a Qualcom Atheros

QCNF344

Quoted 7 lines

wireless chip, which is shown by lspci as:

Qualcomm Atheros Device 003e (rev 20)
Subsystem: Foxconn International, Inc. Device e08e

I have installed the linux-next kernel from today 8:00 UTC. I was able to load the ath10k_pci driver, but the driver complains

about

Quoted 2 lines

missing firmware.
I installed a firmware from here: https://github.com/kvalo/ath10k-

firmware

Quoted 9 lines

under /lib/firmware/ath10k/QCA6174/hw2.1/
But also the card is not working.

The output from dmesg is:

[ 9360.538767] ath10k_pci 0000:07:00.0: pci irq msi interrupts 1
irq_mode 0 reset_mode 0
[ 9360.788588] ath10k_pci 0000:07:00.0: Direct firmware load for
ath10k/cal-pci-0000:07:00.0.bin failed with error -2
[ 9362.729118] ath10k_pci 0000:07:00.0: unable to write to the 

device

Quoted 6 lines
[ 9362.729120] ath10k_pci 0000:07:00.0: failed to download normal
firmware: -110
[ 9362.729121] ath10k_pci 0000:07:00.0: could not init core (-110)
[ 9362.729156] ath10k_pci 0000:07:00.0: could not probe fw (-110)

I would like to know, as Austin Hendrix wrote it at 8 Feb 14:12

2015

Quoted 2 lines

too, where can I find the firmware on the
internet / my Windows7 partition and how can I prepare the needed

files.

Quoted 5 lines

Many thanks,

Olaf

Hi did you advance anything on this?

Trying to run a QCA6164 card myself on a Lenovo 3-14 laptop. Sems I've gotten as far as you.
Prepared Ath10k hw2.1 board.bin and firmware-4.bin for hw2.1 using windows binary driver. (And assemble.py, disassemble.py tools linked elsewhere)

Board.bin seems to load and execute fine. But after that when loading firmware-4.bin, it ends up with Unable to write to the device.

I see it starts sending firmware-4.bin and first 256 bytes ce_send fine.
2nd ce_send 256 bytes seem to also ce_send fine, however after that bmi_wait times out. (-110)

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#2 lore raw
Quoted 50 lines · Oscar Rydberg
Quoted 2 lines · Olaf Dreyer <olaf <at> dreyero.de> writes:

I have a new Acer Aspire VN7-591 Laptop with a Qualcom Atheros

QCNF344

Quoted 7 lines

wireless chip, which is shown by lspci as:

Qualcomm Atheros Device 003e (rev 20)
Subsystem: Foxconn International, Inc. Device e08e

I have installed the linux-next kernel from today 8:00 UTC. I was able to load the ath10k_pci driver, but the driver complains

about

Quoted 2 lines

missing firmware.
I installed a firmware from here: https://github.com/kvalo/ath10k-

firmware

Quoted 9 lines

under /lib/firmware/ath10k/QCA6174/hw2.1/
But also the card is not working.

The output from dmesg is:

[ 9360.538767] ath10k_pci 0000:07:00.0: pci irq msi interrupts 1
irq_mode 0 reset_mode 0
[ 9360.788588] ath10k_pci 0000:07:00.0: Direct firmware load for
ath10k/cal-pci-0000:07:00.0.bin failed with error -2
[ 9362.729118] ath10k_pci 0000:07:00.0: unable to write to the

device

Quoted 6 lines
[ 9362.729120] ath10k_pci 0000:07:00.0: failed to download normal
firmware: -110
[ 9362.729121] ath10k_pci 0000:07:00.0: could not init core (-110)
[ 9362.729156] ath10k_pci 0000:07:00.0: could not probe fw (-110)

I would like to know, as Austin Hendrix wrote it at 8 Feb 14:12

2015

Quoted 2 lines

too, where can I find the firmware on the
internet / my Windows7 partition and how can I prepare the needed

files.

Quoted 5 lines

Many thanks,

Olaf

Hi did you advance anything on this?

Trying to run a QCA6164 card myself on a Lenovo 3-14 laptop. Sems I've gotten as far as you.
Prepared Ath10k hw2.1 board.bin and firmware-4.bin for hw2.1 using windows binary driver. (And assemble.py, disassemble.py tools linked elsewhere)

Quoted 8 lines

Board.bin seems to load and execute fine. But after that when loading firmware-4.bin, it ends up with Unable to write to the device.

I see it starts sending firmware-4.bin and first 256 bytes ce_send fine.
2nd ce_send 256 bytes seem to also ce_send fine, however after that bmi_wait times out. (-110)

You're most likely trying to push something that isn't an actual firmware blob to the device. You might be interested in the other
thread: http://lists.infradead.org/pipermail/ath10k/2015-April/005072.html

Michał

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k