iMX6 IPU configuration by EDID
Hi all,
I'm trying to configure IPU on a iMX6 based platform by reading EDID from the external monitor.
Everything seem to work fine except for the pixelclock. In particular my monitor has a standard resolution of 1280x1024 at 60 (108 MHz pixelclock).
When the function ipu_init_sync_panel (file ipu_disp.c) is called it correctly receive 108 MHz as pixelclock. but during the execution of this function it gets rounded to 130 MHz.
I can see that the function calls clk_round_rate to round the clock to 130 MHz but it's not clear for me how it works.
Can someone please tell me how to get the exact pixelclock I would like to achieve? I've carefully read the iMX6 manual but it's not very useful in this case.
Another doubt that I have regards the field "ext_clk" of parameter "ipu_di_signal_cfg_t sig". In this case, is it better to set it or not?
Thanks
Regards
Luca
Signature · 4 lines
Luca Ellero E-mail: luca.ellero at brickedbrain.com Internet: www.brickedbrain.com
Hi Luca,
Quoted 8 lines · Luca Ellero
Hi all,
I'm trying to configure IPU on a iMX6 based platform by reading EDID from the external monitor.
Everything seem to work fine except for the pixelclock. In particular my monitor has a standard resolution of 1280x1024 at 60 (108 MHz pixelclock).
Quoted 7 lines
When the function
ipu_init_sync_panel(fileipu_disp.c) is called it correctly receive 108 MHz as pixelclock. but during the execution of this function it gets rounded to 130 MHz.I can see that the function calls
clk_round_rateto round the clock to 130 MHz but it's not clear for me how it works.
It's been a while since I've looked at this, but I believe there's a hidden fixed clock somewhere in the IPU driver.
http://lists.denx.de/pipermail/u-boot/2014-January/thread.html#170363
Quoted 7 lines
Can someone please tell me how to get the exact pixelclock I would like to achieve? I've carefully read the iMX6 manual but it's not very useful in this case.
Another doubt that I have regards the field "
ext_clk" of parameter "ipu_di_signal_cfg_tsig". In this case, is it better to set it or not?
I believe this is supposed to be set for HDMI, such that the IPU clock is derived from the HDMI PHY clock and it's best to use the Linux driver as a guide.
Regards,
Eric
Quoted 28 lines · Eric Nelson
Hi Luca,
Quoted 8 lines · Luca Ellero
Hi all,
I'm trying to configure IPU on a iMX6 based platform by reading EDID from the external monitor.
Everything seem to work fine except for the pixelclock. In particular my monitor has a standard resolution of 1280x1024 at 60 (108 MHz pixelclock).
Quoted 7 lines
When the function
ipu_init_sync_panel(fileipu_disp.c) is called it correctly receive 108 MHz as pixelclock. but during the execution of this function it gets rounded to 130 MHz.I can see that the function calls
clk_round_rateto round the clock to 130 MHz but it's not clear for me how it works.It's been a while since I've looked at this, but I believe there's a hidden fixed clock somewhere in the IPU driver.
http://lists.denx.de/pipermail/u-boot/2014-January/thread.html#170363Quoted 4 lines
Can someone please tell me how to get the exact pixelclock I would like to achieve? I've carefully read the iMX6 manual but it's not very useful in this case.
Quoted 8 lines
Quoted 3 lines
Another doubt that I have regards the field "
ext_clk" of parameter "ipu_di_signal_cfg_tsig". In this case, is it better to set it or not?I believe this is supposed to be set for HDMI, such that the IPU clock is derived from the HDMI PHY clock and it's best to use the Linux driver as a guide.
Hi Eric,
thank you for your reply.
I'll try to investigate the Linux driver then.
Kind regards
Luca
Signature · 4 lines
Luca Ellero E-mail: luca.ellero at brickedbrain.com Internet: www.brickedbrain.com