Skip to contentSkip to conversation

iMX6 IPU configuration by EDID

U-Boot Luca Ellero 2 participants 3 messages Mar 17, 2015 – Mar 18, 2015

lore
Share & tools
lore
#0 lore raw

Hi all,
I'm trying to configure IPU on a iMX6 based platform by reading EDID from the external monitor.

Everything seem to work fine except for the pixelclock. In particular my monitor has a standard resolution of 1280x1024 at 60 (108 MHz pixelclock).

When the function ipu_init_sync_panel (file ipu_disp.c) is called it correctly receive 108 MHz as pixelclock. but during the execution of this function it gets rounded to 130 MHz.

I can see that the function calls clk_round_rate to round the clock to 130 MHz but it's not clear for me how it works.

Can someone please tell me how to get the exact pixelclock I would like to achieve? I've carefully read the iMX6 manual but it's not very useful in this case.

Another doubt that I have regards the field "ext_clk" of parameter "ipu_di_signal_cfg_t sig". In this case, is it better to set it or not?

Thanks
Regards
Luca

Signature · 4 lines
Luca Ellero

E-mail: luca.ellero at brickedbrain.com
Internet: www.brickedbrain.com
#1 lore raw

Hi Luca,

Quoted 8 lines · Luca Ellero

Hi all,

I'm trying to configure IPU on a iMX6 based platform by reading EDID from the external monitor.

Everything seem to work fine except for the pixelclock. In particular my monitor has a standard resolution of 1280x1024 at 60 (108 MHz pixelclock).

Quoted 7 lines

When the function ipu_init_sync_panel (file ipu_disp.c) is called it correctly receive 108 MHz as pixelclock. but during the execution of this function it gets rounded to 130 MHz.

I can see that the function calls clk_round_rate to round the clock to 130 MHz but it's not clear for me how it works.

It's been a while since I've looked at this, but I believe there's a hidden fixed clock somewhere in the IPU driver.

	http://lists.denx.de/pipermail/u-boot/2014-January/thread.html#170363
Quoted 7 lines

Can someone please tell me how to get the exact pixelclock I would like to achieve? I've carefully read the iMX6 manual but it's not very useful in this case.

Another doubt that I have regards the field "ext_clk" of parameter "ipu_di_signal_cfg_t sig". In this case, is it better to set it or not?

I believe this is supposed to be set for HDMI, such that the IPU clock is derived from the HDMI PHY clock and it's best to use the Linux driver as a guide.

Regards,

Eric

#2 lore raw
Quoted 28 lines · Eric Nelson

Hi Luca,

Quoted 8 lines · Luca Ellero

Hi all,

I'm trying to configure IPU on a iMX6 based platform by reading EDID from the external monitor.

Everything seem to work fine except for the pixelclock. In particular my monitor has a standard resolution of 1280x1024 at 60 (108 MHz pixelclock).

Quoted 7 lines

When the function ipu_init_sync_panel (file ipu_disp.c) is called it correctly receive 108 MHz as pixelclock. but during the execution of this function it gets rounded to 130 MHz.

I can see that the function calls clk_round_rate to round the clock to 130 MHz but it's not clear for me how it works.

It's been a while since I've looked at this, but I believe there's a hidden fixed clock somewhere in the IPU driver.

	http://lists.denx.de/pipermail/u-boot/2014-January/thread.html#170363
Quoted 4 lines

Can someone please tell me how to get the exact pixelclock I would like to achieve? I've carefully read the iMX6 manual but it's not very useful in this case.

Quoted 8 lines
Quoted 3 lines

Another doubt that I have regards the field "ext_clk" of parameter "ipu_di_signal_cfg_t sig". In this case, is it better to set it or not?

I believe this is supposed to be set for HDMI, such that the IPU clock is derived from the HDMI PHY clock and it's best to use the Linux driver as a guide.

Hi Eric,
thank you for your reply.
I'll try to investigate the Linux driver then.
Kind regards
Luca

Signature · 4 lines
Luca Ellero

E-mail: luca.ellero at brickedbrain.com
Internet: www.brickedbrain.com