ARM: dts: imx7d: Fix UART2 base address
Subsystems (2)
Fabio Estevam
reviewerPATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
From: Fabio Estevam <[email protected]>
The UART2 memory space starts at address 0x30890000 (UART2_URXD).
Fix it so that UART2 can be used.
--- arch/arm/boot/dts/imx7d.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/imx7d.dtsi +2 -2
@@ -640,10 +640,10 @@ status = "disabled"; }; - uart2: serial at 30870000 { + uart2: serial at 30890000 { compatible = "fsl,imx7d-uart", "fsl,imx6q-uart"; - reg = <0x30870000 0x10000>; + reg = <0x30890000 0x10000>; interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX7D_UART2_ROOT_CLK>, <&clks IMX7D_UART2_ROOT_CLK>;
Signature · 1 line
1.9.1
PATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The UART2 memory space starts at address
0x30890000(UART2_URXD).Fix it so that UART2 can be used.
Signed-off-by Fabio Estevam <[email protected]>
Frank, can you confirm it?
Shawn
Quoted 24 lines
--- arch/arm/boot/dts/imx7d.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)arch/arm/boot/dts/imx7d.dtsi +2
-2@@ -640,10 +640,10 @@ status = "disabled"; }; - uart2: serial at 30870000 { + uart2: serial at 30890000 { compatible = "fsl,imx7d-uart", "fsl,imx6q-uart"; - reg = <0x30870000 0x10000>; + reg = <0x30890000 0x10000>; interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX7D_UART2_ROOT_CLK>, <&clks IMX7D_UART2_ROOT_CLK>;Signature · 1 line
1.9.1
Fabio Estevam
reviewerPATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
Hi Shawn,
Quoted 10 lines · Shawn Guo
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The UART2 memory space starts at address
0x30890000(UART2_URXD).Fix it so that UART2 can be used.
Signed-off-by Fabio Estevam <[email protected]>Frank, can you confirm it?
This patch uses the UART2 base address as stated in the MX7D Reference Manual.
It has also been tested on a custom board.
PATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
Quoted 8 lines · Fabio Estevam
Hi Shawn,
Quoted 5 lines · Shawn Guo
Quoted 4 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The UART2 memory space starts at address
0x30890000(UART2_URXD).
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Fix it so that UART2 can be used.
Signed-off-by Fabio Estevam <[email protected]>Frank, can you confirm it?
This patch uses the UART2 base address as stated in the MX7D Reference Manual.
Is the Reference Manual published somewhere?
Shawn
Fabio Estevam
reviewerPATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
Hi Shawn,
Quoted 3 lines · Shawn Guo
Quoted 1 line
This patch uses the UART2 base address as stated in the MX7D Reference Manual.
Is the Reference Manual published somewhere?
It is not publicly available at this time
PATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
In reply to Shawn GuoQuoted 11 lines · Shawn Guo
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The UART2 memory space starts at address
0x30890000(UART2_URXD).Fix it so that UART2 can be used.
Signed-off-by Fabio Estevam <[email protected]>Frank, can you confirm it?
Shawn,
Yes, this change is correct. I confirmed in the SoC design db.
Quoted 23 lines
Shawn
Quoted 21 lines
--- arch/arm/boot/dts/imx7d.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)arch/arm/boot/dts/imx7d.dtsi +2
-2@@ -640,10 +640,10 @@ status = "disabled"; }; - uart2: serial at 30870000 { + uart2: serial at 30890000 { compatible = "fsl,imx7d-uart", "fsl,imx6q-uart"; - reg = <0x30870000 0x10000>; + reg = <0x30890000 0x10000>; interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX7D_UART2_ROOT_CLK>, <&clks IMX7D_UART2_ROOT_CLK>;
Quoted 9 lines
Quoted 3 lines
Signature · 1 line
1.9.1_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Regards,
Nitin
PATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
Quoted 11 lines · Nitin Garg
Quoted 10 lines · Shawn Guo
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The UART2 memory space starts at address
0x30890000(UART2_URXD).Fix it so that UART2 can be used.
Signed-off-by Fabio Estevam <[email protected]>Frank, can you confirm it?
Yes, it is correct.
best regards
Frank Li
Quoted 44 lines
Quoted 1 line
Shawn,
Yes, this change is correct. I confirmed in the SoC design db.Quoted 23 lines
Shawn
Quoted 21 lines
--- arch/arm/boot/dts/imx7d.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)arch/arm/boot/dts/imx7d.dtsi +2
-2@@ -640,10 +640,10 @@ status = "disabled"; }; - uart2: serial at 30870000 { + uart2: serial at 30890000 { compatible = "fsl,imx7d-uart", "fsl,imx6q-uart"; - reg = <0x30870000 0x10000>; + reg = <0x30890000 0x10000>; interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX7D_UART2_ROOT_CLK>, <&clks IMX7D_UART2_ROOT_CLK>;Quoted 9 lines
Quoted 3 lines
--
1.9.1_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernelRegards,
Nitin_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Shawn Guo
AppliedPATCH 1/1 ARM: dts: imx7d: Fix UART2 base address
In reply to Fabio EstevamQuoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The UART2 memory space starts at address
0x30890000(UART2_URXD).Fix it so that UART2 can be used.
Signed-off-by Fabio Estevam <[email protected]>
Applied, thanks.