Skip to contentSkip to conversation

help - u-boot on powerpc qemu

U-Boot 吴红青 2 participants 4 messages Dec 13, 2015 – Dec 21, 2015

lore
Share & tools
lore

吴红青

author
#0 lore raw

hello,i am using u-boot on powerpc qemu,my u-boot version is u-boot-2016.01-rc2,i make uboot as below:

cd u-boot-2016.01-rc2
make clean
make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- qemu-ppce500_defconfig make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-

then ,t execute u-boot bay qemu as below:

qemu-system-ppc -M ppce500 -serial stdio -kernel u-boot -m 1024

uboot show some msg as below:

U-Boot 2016.01-rc2 (Dec 13 2015 - 19:54:13 +0800)

CPU:   Unknown, Version: 0.0, (0x00000000)
Core:  e500, Version: 3.0, (0x80210030)
Clock Configuration:
        CPU0:400  MHz,
        CCB:400  MHz,
        DDR:200  MHz (400 MT/s data rate), LBC: unknown (LCRR[CLKDIV] = 
0x00)
L1:    D-cache 32 KiB enabled
        I-cache 32 KiB enabled
DRAM:  1 GiB
L2:    disabled

Using default environment

PCI: base address e0008000
00:01.0 - 1af4:1000 - Network controller
PCI1: Bus 00 - 00

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
WARNING: adjusting available memory to 30000000

Wrong Image Format for bootm command
ERROR: can't get kernel image!
=>

why no net card? can you help me?

thanks you!!!

#1 lore raw

2015-12-13 20:29 GMT+08:00 ??? <[email protected]>:

Quoted 39 lines

hello,i am using u-boot on powerpc qemu,my u-boot version is u-boot-2016.01-rc2,i make uboot as below:

cd u-boot-2016.01-rc2
make clean
make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- qemu-ppce500_defconfig make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-

then ,t execute u-boot bay qemu as below:

qemu-system-ppc -M ppce500 -serial stdio -kernel u-boot -m 1024

uboot show some msg as below:

U-Boot 2016.01-rc2 (Dec 13 2015 - 19:54:13 +0800)

CPU:   Unknown, Version: 0.0, (0x00000000)
Core:  e500, Version: 3.0, (0x80210030)
Clock Configuration:
       CPU0:400  MHz,
       CCB:400  MHz,
       DDR:200  MHz (400 MT/s data rate), LBC: unknown (LCRR[CLKDIV] = 0x00)
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
DRAM:  1 GiB
L2:    disabled

Using default environment

PCI: base address e0008000
00:01.0 - 1af4:1000 - Network controller
PCI1: Bus 00 - 00

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
WARNING: adjusting available memory to 30000000
Quoted 5 lines

Wrong Image Format for bootm command
ERROR: can't get kernel image!
=>

why no net card? can you help me?

Because you didn't specify any emulated NIC in qemu command line.

Here's a link maybe you can refer:

https://www.suse.com/documentation/sles11/book_kvm/data/cha_qemu_running_networking.html

See the "Defining a Network Interface Card" section. The commonly used model with U-Boot should be e1000 or rtl8139 (rtl8139 is not converted to driver model though)

Miao

Quoted 7 lines

thanks you!!!

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

author
#2 lore raw

thank MiaoYan!
i try to do something as you said ,now can found e1000-nic,but when i ping another ipaddr,an error msg show as below:

U-Boot 2016.01-rc2 (Dec 13 2015 - 21:06:24 +0800)

CPU:   Unknown, Version: 0.0, (0x00000000)
Core:  e500, Version: 2.2, (0x80210022)
Clock Configuration:
        CPU0:400  MHz,
        CCB:400  MHz,
        DDR:200  MHz (400 MT/s data rate), LBC: unknown (LCRR[CLKDIV] = 
0x00)
L1:    D-cache 32 KiB enabled
        I-cache 32 KiB enabled
DRAM:  1 GiB
L2:    disabled

Using default environment

PCI: base address e0008000
00:01.0 - 8086:100e - Network controller
PCI1: Bus 00 - 00

In:    serial
Out:   serial
Err:   serial
Net:   e1000: 00:00:00:00:00:00
        e1000#0

Error: e1000#0 address not set.

Hit any key to stop autoboot: 0
WARNING: adjusting available memory to 30000000 Wrong Image Format for bootm command
ERROR: can't get kernel image!
=> setenv ipAddr 10.33.152.222
=> ping 10.33.152.2
e1000: e1000#0: ERROR: Hardware Initialization Failed ping failed; host 10.33.152.2 is not alive
=>

==============================================================================

? 2015?12?14? 10:23, Miao Yan ??:

Quoted 68 lines

2015-12-13 20:29 GMT+08:00 ??? <[email protected]>:

Quoted 39 lines

hello,i am using u-boot on powerpc qemu,my u-boot version is u-boot-2016.01-rc2,i make uboot as below:

cd u-boot-2016.01-rc2
make clean
make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- qemu-ppce500_defconfig make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-

then ,t execute u-boot bay qemu as below:

qemu-system-ppc -M ppce500 -serial stdio -kernel u-boot -m 1024

uboot show some msg as below:

U-Boot 2016.01-rc2 (Dec 13 2015 - 19:54:13 +0800)

CPU:   Unknown, Version: 0.0, (0x00000000)
Core:  e500, Version: 3.0, (0x80210030)
Clock Configuration:
        CPU0:400  MHz,
        CCB:400  MHz,
        DDR:200  MHz (400 MT/s data rate), LBC: unknown (LCRR[CLKDIV] = 0x00)
L1:    D-cache 32 KiB enabled
        I-cache 32 KiB enabled
DRAM:  1 GiB
L2:    disabled

Using default environment

PCI: base address e0008000
00:01.0 - 1af4:1000 - Network controller
PCI1: Bus 00 - 00

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
WARNING: adjusting available memory to 30000000
Quoted 5 lines

Wrong Image Format for bootm command
ERROR: can't get kernel image!
=>

why no net card? can you help me?

Because you didn't specify any emulated NIC in qemu command line.

Here's a link maybe you can refer:

https://www.suse.com/documentation/sles11/book_kvm/data/cha_qemu_running_networking.html

See the "Defining a Network Interface Card" section. The commonly used model with U-Boot should be e1000 or rtl8139 (rtl8139 is not converted to driver model though)

Miao

Quoted 6 lines

thanks you!!!

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#3 lore raw

2015-12-18 9:12 GMT+08:00 ??? <[email protected]>:

Quoted 3 lines

thank MiaoYan!
i try to do something as you said ,now can found e1000-nic,but when i ping another ipaddr,an error msg show as below:

I tried this today and could reproduce the error.

Quoted 28 lines

U-Boot 2016.01-rc2 (Dec 13 2015 - 21:06:24 +0800)

CPU:   Unknown, Version: 0.0, (0x00000000)
Core:  e500, Version: 2.2, (0x80210022)
Clock Configuration:
       CPU0:400  MHz,
       CCB:400  MHz,
       DDR:200  MHz (400 MT/s data rate), LBC: unknown (LCRR[CLKDIV] = 0x00)
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
DRAM:  1 GiB
L2:    disabled

Using default environment

PCI: base address e0008000
00:01.0 - 8086:100e - Network controller
PCI1: Bus 00 - 00

In:    serial
Out:   serial
Err:   serial
Net:   e1000: 00:00:00:00:00:00
       e1000#0

Error: e1000#0 address not set.

Quoted 7 lines

Hit any key to stop autoboot: 0
WARNING: adjusting available memory to 30000000 Wrong Image Format for bootm command
ERROR: can't get kernel image!
=> setenv ipAddr 10.33.152.222
=> ping 10.33.152.2
e1000: e1000#0: ERROR: Hardware Initialization Failed

This is because e1000 pci configuration space is not properly programmed:

=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.01.00 0x8086 0x100e Network controller 0x00
=> pci display 00.01.00
00000000: 100e8086 00000006 02000003 00000008
00000010: 00000000 00000001 00000000 00000000
00000020: 00000000 00000000 00000000 11001af4
00000030: 00040000 00000000 00000000 00000100
=>

Look at offset 0x10 which is BAR0, all zero is not a valid pci address which causes the error when e1000 driver tries to remap it.

It seems U-boot writes address larger than 4GB (the physical address is taken from device tree prepared by qemu and the board enables 36bit addressing) to bar0 while e1000 only supports 32bit pci bar, which result in 0 being written and the upper 32bit address is omitted.

So include the maintainer here for more info.

Note there is another bug in e1000 driver that will hang in BE target, I will send a separate patch to fix that.

Quoted 80 lines

ping failed; host 10.33.152.2 is not alive
=>

==============================================================================

? 2015?12?14? 10:23, Miao Yan ??:

2015-12-13 20:29 GMT+08:00 ??? <[email protected]>:

hello,i am using u-boot on powerpc qemu,my u-boot version is u-boot-2016.01-rc2,i make uboot as below:

cd u-boot-2016.01-rc2
make clean
make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- qemu-ppce500_defconfig make ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-

then ,t execute u-boot bay qemu as below:

qemu-system-ppc -M ppce500 -serial stdio -kernel u-boot -m 1024

uboot show some msg as below:

U-Boot 2016.01-rc2 (Dec 13 2015 - 19:54:13 +0800)

CPU:   Unknown, Version: 0.0, (0x00000000)
Core:  e500, Version: 3.0, (0x80210030)
Clock Configuration:
       CPU0:400  MHz,
       CCB:400  MHz,
       DDR:200  MHz (400 MT/s data rate), LBC: unknown (LCRR[CLKDIV] = 0x00)
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
DRAM:  1 GiB
L2:    disabled

Using default environment

PCI: base address e0008000
00:01.0 - 1af4:1000 - Network controller
PCI1: Bus 00 - 00

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
WARNING: adjusting available memory to 30000000

Wrong Image Format for bootm command
ERROR: can't get kernel image!
=>

why no net card? can you help me?

Because you didn't specify any emulated NIC in qemu command line.

Here's a link maybe you can refer:

https://www.suse.com/documentation/sles11/book_kvm/data/cha_qemu_running_networking.html

See the "Defining a Network Interface Card" section. The commonly used model with U-Boot should be e1000 or rtl8139 (rtl8139 is not converted to driver model though)

Miao

thanks you!!!

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot