How to obtain Link Quality information
Hi everyone,
I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.
If I try "cat /proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.
I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x
Any ideas on how can I get the link quality information?
Thanks,
Inaki
===============================
monet@sc229:~$ ethtool -i wlan2 driver: ath10k_pci version: 4.2.0+ firmware-version: 10.1.467-ct-_fH-016-b797ef5 bus-info: 0000:0b:00.0 supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no monet@sc229:~$ =============================== monet@sc229:~$ cat /proc/net/wireless Inter-| sta-| Quality | Discarded packets | Missed | WE face | tus | link level noise | nwid crypt frag retry misc | beacon | 22 monet@sc229:~$
===============================
monet@sc229:~$ iwconfig wlan2
wlan2 IEEE 802.11abgn ESSID:"SC228SC229"
Mode:Ad-Hoc Frequency:5.24 GHz Cell: 8E:CE:DE:4F:86:95
Tx-Power=17 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:onmonet@sc229:~$
===============================
monet@sc229:~$ iw wlan2 link
Joined IBSS 8e:ce:de:4f:86:95 (on wlan2)
SSID: SC228SC229
freq: 5240
monet@sc229:~$
===============================_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 11 lines · Iñaki Pascual
Hi everyone,
I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.
If I try "cat
/proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x
Any ideas on how can I get the link quality information?
Did you try:
iw dev wlan0 station dump
If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...
Thanks,
Ben
Signature · 8 lines
Ben Greear <[email protected]> Candela Technologies Inc http://www.candelatech.com _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Hi Ben,
yes, I tried, it shows signal value but not link quality :(
onet@sc229:~$ iw dev wlan2 station dump
Station 04:f0:21:18:26:af (on wlan2)
inactive time: 65 ms
rx bytes: 3102896
rx packets: 87403
tx bytes: 0
tx packets: 0
tx retries: 0
tx failed: 0
signal: -63 dBm
signal avg: -62 dBm
tx bitrate: 6.0 MBit/s
rx bitrate: 6.0 MBit/s
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
connected time: 4476 seconds
monet@sc229:~$Thanks,
Iñaki
Quoted 15 lines · Ben Greear
Quoted 11 lines · Iñaki Pascual
Hi everyone,
I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.
If I try "cat
/proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x
Any ideas on how can I get the link quality information?
Did you try:
Quoted 9 lines
iw dev wlan0 station dump
If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...
Thanks,
Ben
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 3 lines · Iñaki Pascual
Hi Ben,
yes, I tried, it shows signal value but not link quality :(
Link 'quality' is mostly just a made-up number anyway. Signal quality is probably the most similar value, but tx and rx bitrates give you the best idea of how RF is performing in my opinion. Those rates are only accurate when sending at least modest amounts of packets though.
Thanks,
Ben
Quoted 59 lines
onet@sc229:~$ iw dev wlan2 station dump Station 04:f0:21:18:26:af (on wlan2) inactive time: 65 ms rx bytes: 3102896 rx packets: 87403 tx bytes: 0 tx packets: 0 tx retries: 0 tx failed: 0 signal: -63 dBm signal avg: -62 dBm tx bitrate: 6.0 MBit/s rx bitrate: 6.0 MBit/s authorized: yes authenticated: yes preamble: long WMM/WME: yes MFP: no TDLS peer: no connected time: 4476 seconds monet@sc229:~$Thanks,
Iñaki
Quoted 15 lines · Ben Greear
Quoted 11 lines · Iñaki Pascual
Hi everyone,
I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.
If I try "cat
/proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x
Any ideas on how can I get the link quality information?
Did you try:
Quoted 9 lines
iw dev wlan0 station dump
If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...
Thanks,
Ben_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Signature · 8 lines
Ben Greear <[email protected]> Candela Technologies Inc http://www.candelatech.com _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
tx rate reporting for Candela firmware is working? Any changes go into the QCA released firmware?
---
Chun-Yeow
Quoted 91 lines · Ben Greear
Quoted 4 lines · Iñaki Pascual
Hi Ben,
yes, I tried, it shows signal value but not link quality :(
Link 'quality' is mostly just a made-up number anyway. Signal quality is probably the most similar value, but tx and rx bitrates give you the best idea of how RF is performing in my opinion. Those rates are only accurate when sending at least modest amounts of packets though.
Thanks,
BenQuoted 62 lines
onet@sc229:~$ iw dev wlan2 station dump Station 04:f0:21:18:26:af (on wlan2) inactive time: 65 ms rx bytes: 3102896 rx packets: 87403 tx bytes: 0 tx packets: 0 tx retries: 0 tx failed: 0 signal: -63 dBm signal avg: -62 dBm tx bitrate: 6.0 MBit/s rx bitrate: 6.0 MBit/s authorized: yes authenticated: yes preamble: long WMM/WME: yes MFP: no TDLS peer: no connected time: 4476 seconds monet@sc229:~$Thanks,
Iñaki
Quoted 23 lines · Ben Greear
Quoted 13 lines · Iñaki Pascual
Hi everyone,
I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as
it scans all channels and takes a while.If I try "cat
/proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below
is the output for some commands I tried.Quoted 4 lines
I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x
Any ideas on how can I get the link quality information?
Did you try:
Quoted 9 lines
iw dev wlan0 station dump
If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...
Thanks,
BenQuoted 5 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com
Quoted 4 lines
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 2 lines · Yeoh Chun-Yeow
tx rate reporting for Candela firmware is working? Any changes go into the QCA released firmware?
It is working in CT firmware (when using my patched ath10k driver to support the feature), and I have no way to get changes into upstream QCA firmware.
Thanks,
Ben
Signature · 8 lines
Ben Greear <[email protected]> Candela Technologies Inc http://www.candelatech.com _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k