Skip to contentSkip to conversation

How to obtain Link Quality information

DISCUSSION Iñaki Pascual 3 participants 6 messages Jul 13, 2016 – Jul 14, 2016 Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore
#0 lore raw

Hi everyone,

I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.

If I try "cat /proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.

I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x

Any ideas on how can I get the link quality information?

Thanks,

Inaki

===============================

monet@sc229:~$ ethtool -i wlan2
driver: ath10k_pci
version: 4.2.0+
firmware-version: 10.1.467-ct-_fH-016-b797ef5
bus-info: 0000:0b:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
monet@sc229:~$
===============================
monet@sc229:~$ cat /proc/net/wireless
Inter-| sta-|   Quality        |   Discarded packets               | Missed | WE
 face | tus | link level noise |  nwid  crypt   frag  retry   misc | 
beacon | 22
monet@sc229:~$

===============================

monet@sc229:~$ iwconfig wlan2
wlan2     IEEE 802.11abgn  ESSID:"SC228SC229"
          Mode:Ad-Hoc  Frequency:5.24 GHz  Cell: 8E:CE:DE:4F:86:95
          Tx-Power=17 dBm
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:on

monet@sc229:~$
===============================

monet@sc229:~$ iw wlan2 link
Joined IBSS 8e:ce:de:4f:86:95 (on wlan2)
    SSID: SC228SC229
    freq: 5240
monet@sc229:~$
===============================

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#1 lore raw
Quoted 11 lines · Iñaki Pascual

Hi everyone,

I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.

If I try "cat /proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.

I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x

Any ideas on how can I get the link quality information?

Did you try:

iw dev wlan0 station dump

If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...

Thanks,
Ben

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#2 lore raw

Hi Ben,

yes, I tried, it shows signal value but not link quality :(

onet@sc229:~$ iw dev wlan2 station dump
Station 04:f0:21:18:26:af (on wlan2)
    inactive time:    65 ms
    rx bytes:    3102896
    rx packets:    87403
    tx bytes:    0
    tx packets:    0
    tx retries:    0
    tx failed:    0
    signal:      -63 dBm
    signal avg:    -62 dBm
    tx bitrate:    6.0 MBit/s
    rx bitrate:    6.0 MBit/s
    authorized:    yes
    authenticated:    yes
    preamble:    long
    WMM/WME:    yes
    MFP:        no
    TDLS peer:    no
    connected time:    4476 seconds
monet@sc229:~$

Thanks,

Iñaki

Quoted 15 lines · Ben Greear
Quoted 11 lines · Iñaki Pascual

Hi everyone,

I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.

If I try "cat /proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.

I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x

Any ideas on how can I get the link quality information?

Did you try:

Quoted 9 lines

iw dev wlan0 station dump

If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...

Thanks,
Ben

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#3 lore raw
Quoted 3 lines · Iñaki Pascual

Hi Ben,

yes, I tried, it shows signal value but not link quality :(

Link 'quality' is mostly just a made-up number anyway. Signal quality is probably the most similar value, but tx and rx bitrates give you the best idea of how RF is performing in my opinion. Those rates are only accurate when sending at least modest amounts of packets though.

Thanks,
Ben

Quoted 59 lines
onet@sc229:~$ iw dev wlan2 station dump
Station 04:f0:21:18:26:af (on wlan2)
     inactive time:    65 ms
     rx bytes:    3102896
     rx packets:    87403
     tx bytes:    0
     tx packets:    0
     tx retries:    0
     tx failed:    0
     signal:      -63 dBm
     signal avg:    -62 dBm
     tx bitrate:    6.0 MBit/s
     rx bitrate:    6.0 MBit/s
     authorized:    yes
     authenticated:    yes
     preamble:    long
     WMM/WME:    yes
     MFP:        no
     TDLS peer:    no
     connected time:    4476 seconds
monet@sc229:~$

Thanks,

Iñaki

Quoted 15 lines · Ben Greear
Quoted 11 lines · Iñaki Pascual

Hi everyone,

I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as it scans all channels and takes a while.

If I try "cat /proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below is the output for some commands I tried.

I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x

Any ideas on how can I get the link quality information?

Did you try:

Quoted 9 lines

iw dev wlan0 station dump

If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...

Thanks,
Ben

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#4 lore raw

tx rate reporting for Candela firmware is working? Any changes go into the QCA released firmware?

---
Chun-Yeow

Quoted 91 lines · Ben Greear
Quoted 4 lines · Iñaki Pascual

Hi Ben,

yes, I tried, it shows signal value but not link quality :(

Link 'quality' is mostly just a made-up number anyway. Signal quality is probably the most similar value, but tx and rx bitrates give you the best idea of how RF is performing in my opinion. Those rates are only accurate when sending at least modest amounts of packets though.

Thanks,
Ben

Quoted 62 lines
onet@sc229:~$ iw dev wlan2 station dump
Station 04:f0:21:18:26:af (on wlan2)
     inactive time:    65 ms
     rx bytes:    3102896
     rx packets:    87403
     tx bytes:    0
     tx packets:    0
     tx retries:    0
     tx failed:    0
     signal:      -63 dBm
     signal avg:    -62 dBm
     tx bitrate:    6.0 MBit/s
     rx bitrate:    6.0 MBit/s
     authorized:    yes
     authenticated:    yes
     preamble:    long
     WMM/WME:    yes
     MFP:        no
     TDLS peer:    no
     connected time:    4476 seconds
monet@sc229:~$

Thanks,

Iñaki

Quoted 23 lines · Ben Greear
Quoted 13 lines · Iñaki Pascual

Hi everyone,

I am trying to get link quality information from an 802.11ac interface and it looks like the only way is to use "iw wlan2 scan". I don't like this solution as
it scans all channels and takes a while.

If I try "cat /proc/net/wireless" (this would be my preferred option) the output is empty and I am not able to get this information with any other tool. Below
is the output for some commands I tried.

Quoted 4 lines

I am using kernel 4.2 with ath10k and Candela firmware 10.1 on a Qualcomm Atheros QCA988x

Any ideas on how can I get the link quality information?

Did you try:

Quoted 9 lines

iw dev wlan0 station dump

If you want tx rate reporting, you need to run my driver patches as well as my firmware, but rx-rate should be reported with stock driver (and stock firmware, for that matter)...

Thanks,
Ben

Quoted 5 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

--
Ben Greear <[email protected]>
Candela Technologies Inc http://www.candelatech.com

Quoted 4 lines

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#5 lore raw
Quoted 2 lines · Yeoh Chun-Yeow

tx rate reporting for Candela firmware is working? Any changes go into the QCA released firmware?

It is working in CT firmware (when using my patched ath10k driver to support the feature), and I have no way to get changes into upstream QCA firmware.

Thanks,
Ben

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k