HDMI 2.0: Scrambling support in DRM layer
Subsystems (4)
cover HDMI 2.0: Scrambling support in DRM layer
HDMI 2.0 spec defines a method to reduce the RF footprint while operating at higher pixel clocks, which is called Scrambling. Scrambling can be controlled over a new set of I2C registers which are accessible over existing DDC I2C lines, called SCDC register set.
This patch series contains 6 patches:
- First two patches add generic drm helper functions to read and write into SCDC registers. These patches are written by Thierry, in a patch series published here:
https://patchwork.kernel.org/patch/9459051/
Minor changes were done to map the patches into this series.
- Next two patches add functions for scrambling detection and scrambling control.
- Next two patches use this infrastructure in DRM layer from I915 driver, to enable scrambling on a GLK deivce which sports a native HDMI 2.0 controller.
Shashank Sharma (4):
drm/edid: detect SCDC support in HF-VSDB
drm: scrambling support in drm layer
drm/i915: enable scrambling
drm/i915: allow HDMI 2.0 clock rates
Thierry Reding (2):
drm: Add SCDC helpers
drm/edid: check for HF-VSDB block
Documentation/gpu/drm-kms-helpers.rst | 12 +++ drivers/gpu/drm/Makefile | 3 +- drivers/gpu/drm/drm_edid.c | 158 ++++++++++++++++++++++++++++++++++ drivers/gpu/drm/drm_scdc_helper.c | 111 ++++++++++++++++++++++++ drivers/gpu/drm/i915/i915_reg.h | 2 + drivers/gpu/drm/i915/intel_ddi.c | 5 ++ drivers/gpu/drm/i915/intel_drv.h | 2 + drivers/gpu/drm/i915/intel_hdmi.c | 44 ++++++++++ include/drm/drm_connector.h | 50 +++++++++++ include/drm/drm_edid.h | 6 +- include/drm/drm_scdc_helper.h | 132 ++++++++++++++++++++++++++++ include/linux/hdmi.h | 1 + 12 files changed, 524 insertions(+), 2 deletions(-) create mode 100644 drivers/gpu/drm/drm_scdc_helper.c create mode 100644 include/drm/drm_scdc_helper.h
Signature · 6 lines
1.9.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH 1/6 drm: Add SCDC helpers
From: Thierry Reding <[email protected]>
SCDC is a mechanism defined in the HDMI 2.0 specification that allows the source and sink devices to communicate.
This commit introduces helpers to access the SCDC and provides the symbolic names for the various registers defined in the specification.
--- Documentation/gpu/drm-kms-helpers.rst | 12 ++++ drivers/gpu/drm/Makefile | 3 +- drivers/gpu/drm/drm_scdc_helper.c | 111 ++++++++++++++++++++++++++++ include/drm/drm_scdc_helper.h | 132 ++++++++++++++++++++++++++++++++++ 4 files changed, 257 insertions(+), 1 deletion(-) create mode 100644 drivers/gpu/drm/drm_scdc_helper.c create mode 100644 include/drm/drm_scdc_helper.h
Documentation/gpu/drm-kms-helpers.rst +12 -0
@@ -217,6 +217,18 @@ EDID Helper Functions Reference .. kernel-doc:: drivers/gpu/drm/drm_edid.c :export: +SCDC Helper Functions Reference +=============================== + +.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c + :doc: scdc helpers + +.. kernel-doc:: include/drm/drm_scdc_helper.h + :internal: + +.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c + :export: + Rectangle Utilities Reference =============================
drivers/gpu/drm/Makefile +2 -1
@@ -31,7 +31,8 @@ drm-$(CONFIG_DEBUG_FS) += drm_debugfs.o drm_debugfs_crc.o drm_kms_helper-y := drm_crtc_helper.o drm_dp_helper.o drm_probe_helper.o \ drm_plane_helper.o drm_dp_mst_topology.o drm_atomic_helper.o \ drm_kms_helper_common.o drm_dp_dual_mode_helper.o \ - drm_simple_kms_helper.o drm_modeset_helper.o + drm_simple_kms_helper.o drm_modeset_helper.o \ + drm_scdc_helper.o drm_kms_helper-$(CONFIG_DRM_LOAD_EDID_FIRMWARE) += drm_edid_load.o drm_kms_helper-$(CONFIG_DRM_FBDEV_EMULATION) += drm_fb_helper.o
drivers/gpu/drm/drm_scdc_helper.c new file +111 -0
111 lines not on this page · raw message
include/drm/drm_scdc_helper.h new file +132 -0
132 lines not on this page · raw message
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 1/6] drm: Add SCDC helpers
Quoted 9 lines · Shashank Sharma
From: Thierry Reding <[email protected]>
SCDC is a mechanism defined in the HDMI 2.0 specification that allows the source and sink devices to communicate.
This commit introduces helpers to access the SCDC and provides the symbolic names for the various registers defined in the specification.
Signed-off-by Thierry Reding <[email protected]>
One process note, you need to add your own Signed-off-by under the original author's sign-off, even when you're posting them unchanged.
Signed-off-by means https://developercertificate.org/
BR,
Jani.
Quoted 301 lines
--- Documentation/gpu/drm-kms-helpers.rst | 12 ++++ drivers/gpu/drm/Makefile | 3 +- drivers/gpu/drm/drm_scdc_helper.c | 111 ++++++++++++++++++++++++++++ include/drm/drm_scdc_helper.h | 132 ++++++++++++++++++++++++++++++++++ 4 files changed, 257 insertions(+), 1 deletion(-) create mode 100644 drivers/gpu/drm/drm_scdc_helper.c create mode 100644 include/drm/drm_scdc_helper.hDocumentation/gpu/drm-kms-helpers.rst +12
-0@@ -217,6 +217,18 @@ EDID Helper Functions Reference .. kernel-doc:: drivers/gpu/drm/drm_edid.c :export: +SCDC Helper Functions Reference +=============================== + +.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c + :doc: scdc helpers + +.. kernel-doc:: include/drm/drm_scdc_helper.h + :internal: + +.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c + :export: + Rectangle Utilities Reference =============================drivers/gpu/drm/Makefile +2
-1@@ -31,7 +31,8 @@ drm-$(CONFIG_DEBUG_FS) += drm_debugfs.o drm_debugfs_crc.o drm_kms_helper-y := drm_crtc_helper.o drm_dp_helper.o drm_probe_helper.o \ drm_plane_helper.o drm_dp_mst_topology.o drm_atomic_helper.o \ drm_kms_helper_common.o drm_dp_dual_mode_helper.o \ - drm_simple_kms_helper.o drm_modeset_helper.o + drm_simple_kms_helper.o drm_modeset_helper.o \ + drm_scdc_helper.o drm_kms_helper-$(CONFIG_DRM_LOAD_EDID_FIRMWARE) += drm_edid_load.o drm_kms_helper-$(CONFIG_DRM_FBDEV_EMULATION) += drm_fb_helper.odrivers/gpu/drm/drm_scdc_helper.c new file +111
-0@@ -0,0 +1,111 @@ +/* +* Copyright (c) 2015 NVIDIA Corporation. All rights reserved. +* +* Permission is hereby granted, free of charge, to any person obtaining a +* copy of this software and associated documentation files (the "Software"), +* to deal in the Software without restriction, including without limitation +* the rights to use, copy, modify, merge, publish, distribute, sub license, +* and/or sell copies of the Software, and to permit persons to whom the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including the +* next paragraph) shall be included in all copies or substantial portions +* of the Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER +* DEALINGS IN THE SOFTWARE. +*/ + +#include <linux/slab.h> + +#include <drm/drm_scdc_helper.h> + +/** +* DOC: scdc helpers +* +* Status and Control Data Channel (SCDC) is a mechanism introduced by the +* HDMI 2.0 specification. It is a point-to-point protocol that allows the +* HDMI source and HDMI sink to exchange data. The same I2C interface that +* is used to access EDID serves as the transport mechanism for SCDC. +*/ + +#define SCDC_I2C_SLAVE_ADDRESS 0x54 + +/** +* drm_scdc_read - read a block of data from SCDC +* @adapter: I2C controller +* @offset: start offset of block to read +* @buffer: return location for the block to read +* @size: size of the block to read +* +* Reads a block of data from SCDC, starting at a given offset. +* +* Returns: +* The number of bytes read from SCDC or a negative error code on failure. +*/ +ssize_t drm_scdc_read (struct i2c_adapter *adapter,u8 offset,void *buffer, +size_t size) +{ +struct i2c_msg msgs[2 ] = { + { + .addr =SCDC_I2C_SLAVE_ADDRESS , + .flags =0 , + .len =1 , + .buf = &offset, + }, { + .addr =SCDC_I2C_SLAVE_ADDRESS , + .flags =I2C_M_RD , + .len = size, + .buf = buffer, + } + }; + +return i2c_transfer (adapter, msgs,ARRAY_SIZE (msgs)); +} +EXPORT_SYMBOL (drm_scdc_read); + +/** +* drm_scdc_write - write a block of data to SCDC +* @adapter: I2C controller +* @offset: start offset of block to write +* @buffer: block of data to write +* @size: size of the block to write +* +* Writes a block of data to SCDC, starting at a given offset. +* +* Returns: +* The number of bytes written to SCDC or a negative error code on failure. +*/ +ssize_t drm_scdc_write (struct i2c_adapter *adapter,u8 offset, +const void *buffer,size_t size) +{ +struct i2c_msg msg = { + .addr =SCDC_I2C_SLAVE_ADDRESS , + .flags =0 , + .len =1 + size, + .buf =NULL , + }; +void *data; +int err; + + data =kmalloc (1 + size,GFP_TEMPORARY ); +if (!data) +return -ENOMEM ; + + msg.buf = data; + +memcpy (data, &offset,sizeof (offset)); +memcpy (data +1 , buffer, size); + + err =i2c_transfer (adapter, &msg,1 ); + +kfree (data); + +return err; +} +EXPORT_SYMBOL (drm_scdc_write);include/drm/drm_scdc_helper.h new file +132
-0@@ -0,0 +1,132 @@ +/* +* Copyright (c) 2015 NVIDIA Corporation. All rights reserved. +* +* Permission is hereby granted, free of charge, to any person obtaining a +* copy of this software and associated documentation files (the "Software"), +* to deal in the Software without restriction, including without limitation +* the rights to use, copy, modify, merge, publish, distribute, sub license, +* and/or sell copies of the Software, and to permit persons to whom the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including the +* next paragraph) shall be included in all copies or substantial portions +* of the Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER +* DEALINGS IN THE SOFTWARE. +*/ + +#ifndef DRM_SCDC_HELPER_H +#define DRM_SCDC_HELPER_H + +#include <linux/i2c.h> +#include <linux/types.h> + +#define SCDC_SINK_VERSION 0x01 + +#define SCDC_SOURCE_VERSION 0x02 + +#define SCDC_UPDATE_0 0x10 +#define SCDC_READ_REQUEST_TEST (1 << 2) +#define SCDC_CED_UPDATE (1 << 1) +#define SCDC_STATUS_UPDATE (1 << 0) + +#define SCDC_UPDATE_1 0x11 + +#define SCDC_TMDS_CONFIG 0x20 +#define SCDC_TMDS_BIT_CLOCK_RATIO_BY_40 (1 << 1) +#define SCDC_TMDS_BIT_CLOCK_RATIO_BY_10 (0 << 1) +#define SCDC_SCRAMBLING_ENABLE (1 << 0) + +#define SCDC_SCRAMBLER_STATUS 0x21 +#define SCDC_SCRAMBLING_STATUS (1 << 0) + +#define SCDC_CONFIG_0 0x30 +#define SCDC_READ_REQUEST_ENABLE (1 << 0) + +#define SCDC_STATUS_FLAGS_0 0x40 +#define SCDC_CH2_LOCK (1 < 3) +#define SCDC_CH1_LOCK (1 < 2) +#define SCDC_CH0_LOCK (1 < 1) +#define SCDC_CH_LOCK_MASK (SCDC_CH2_LOCK | SCDC_CH1_LOCK | SCDC_CH0_LOCK) +#define SCDC_CLOCK_DETECT (1 << 0) + +#define SCDC_STATUS_FLAGS_1 0x41 + +#define SCDC_ERR_DET_0_L 0x50 +#define SCDC_ERR_DET_0_H 0x51 +#define SCDC_ERR_DET_1_L 0x52 +#define SCDC_ERR_DET_1_H 0x53 +#define SCDC_ERR_DET_2_L 0x54 +#define SCDC_ERR_DET_2_H 0x55 +#define SCDC_CHANNEL_VALID (1 << 7) + +#define SCDC_ERR_DET_CHECKSUM 0x56 + +#define SCDC_TEST_CONFIG_0 0xc0 +#define SCDC_TEST_READ_REQUEST (1 << 7) +#define SCDC_TEST_READ_REQUEST_DELAY (x) ((x) & 0x7f) + +#define SCDC_MANUFACTURER_IEEE_OUI 0xd0 +#define SCDC_MANUFACTURER_IEEE_OUI_SIZE 3 + +#define SCDC_DEVICE_ID 0xd3 +#define SCDC_DEVICE_ID_SIZE 8 + +#define SCDC_DEVICE_HARDWARE_REVISION 0xdb +#define SCDC_DEVICE_HARDWARE_REVISION_MAJOR (x) (((x) >> 4) & 0xf) +#define SCDC_DEVICE_HARDWARE_REVISION_MINOR (x) (((x) >> 0) & 0xf) + +#define SCDC_DEVICE_SOFTWARE_MAJOR_REVISION 0xdc +#define SCDC_DEVICE_SOFTWARE_MINOR_REVISION 0xdd + +#define SCDC_MANUFACTURER_SPECIFIC 0xde +#define SCDC_MANUFACTURER_SPECIFIC_SIZE 34 + +ssize_t drm_scdc_read (struct i2c_adapter *adapter,u8 offset,void *buffer, +size_t size); +ssize_t drm_scdc_write (struct i2c_adapter *adapter,u8 offset, +const void *buffer,size_t size); + +/** +* drm_scdc_readb - read a single byte from SCDC +* @adapter: I2C adapter +* @offset: offset of register to read +* @value: return location for the register value +* +* Reads a single byte from SCDC. This is a convenience wrapper around the +* drm_scdc_read() function. +* +* Returns: +* 0 on success or a negative error code on failure. +*/ +static inline int drm_scdc_readb (struct i2c_adapter *adapter,u8 offset, +u8 *value) +{ +return drm_scdc_read (adapter, offset, value,sizeof (*value)); +} + +/** +* drm_scdc_writeb - write a single byte to SCDC +* @adapter: I2C adapter +* @offset: offset of register to read +* @value: return location for the register value +* +* Writes a single byte to SCDC. This is a convenience wrapper around the +* drm_scdc_write() function. +* +* Returns: +* 0 on success or a negative error code on failure. +*/ +static inline int drm_scdc_writeb (struct i2c_adapter *adapter,u8 offset, +u8 value) +{ +return drm_scdc_write (adapter, offset, &value,sizeof (value)); +} + +#endif
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 1/6] drm: Add SCDC helpers
Sure, Thanks for the information, will add that in V2.
Regards
Shashank
-----Original Message-----
From: Jani Nikula [mailto:[email protected]]
Sent: Thursday, February 2, 2017 4:55 PM
To: Sharma, Shashank <[email protected]>; [email protected]; [email protected]; [email protected]
Cc: [email protected]; [email protected]; Thierry Reding <[email protected]>; [email protected]
Subject: Re: [Intel-gfx] [PATCH 1/6] drm: Add SCDC helpers
Quoted 9 lines · Shashank Sharma
From: Thierry Reding <[email protected]>
SCDC is a mechanism defined in the HDMI 2.0 specification that allows the source and sink devices to communicate.
This commit introduces helpers to access the SCDC and provides the symbolic names for the various registers defined in the specification.
Signed-off-by Thierry Reding <[email protected]>
One process note, you need to add your own Signed-off-by under the original author's sign-off, even when you're posting them unchanged.
Signed-off-by means https://developercertificate.org/
BR,
Jani.
Quoted 319 lines
--- Documentation/gpu/drm-kms-helpers.rst | 12 ++++ drivers/gpu/drm/Makefile | 3 +- drivers/gpu/drm/drm_scdc_helper.c | 111 ++++++++++++++++++++++++++++ include/drm/drm_scdc_helper.h | 132 ++++++++++++++++++++++++++++++++++ 4 files changed, 257 insertions(+), 1 deletion(-) create mode 100644
drivers/gpu/drm/drm_scdc_helper.ccreate mode 100644include/drm/drm_scdc_helper.hDocumentation/gpu/drm-kms-helpers.rst +0
-0@@ -217,6 +217,18 @@ EDID Helper Functions Reference .. kernel-doc::
drivers/gpu/drm/drm_edid.c
:export:Documentation/gpu/drm-kms-helpers.rst +12
-0+SCDC Helper Functions Reference +=============================== + +.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c + :doc: scdc helpers + +.. kernel-doc:: include/drm/drm_scdc_helper.h + :internal: + +.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c + :export: + Rectangle Utilities Reference =============================drivers/gpu/drm/Makefile index renamed from drivers/gpu/drm/Makefile +0
-092de399..ad91cd9 100644
drivers/gpu/drm/Makefile +2
-2@@ -31,7 +31,8 @@ drm-$(CONFIG_DEBUG_FS) += drm_debugfs.o drm_debugfs_crc.o drm_kms_helper-y := drm_crtc_helper.o drm_dp_helper.o drm_probe_helper.o \ drm_plane_helper.o drm_dp_mst_topology.o drm_atomic_helper.o \ drm_kms_helper_common.o drm_dp_dual_mode_helper.o \ - drm_simple_kms_helper.o drm_modeset_helper.o + drm_simple_kms_helper.o drm_modeset_helper.o \ + drm_scdc_helper.o drm_kms_helper-$(CONFIG_DRM_LOAD_EDID_FIRMWARE) += drm_edid_load.o drm_kms_helper-$(CONFIG_DRM_FBDEV_EMULATION) += drm_fb_helper.o diff --git a/drivers/gpu/drm/drm_scdc_helper.c
b/drivers/gpu/drm/drm_scdc_helper.c
new file mode 100644
index 0000000..fe0e121drivers/gpu/drm/drm_scdc_helper.c new file +125
-0@@ -0,0 +1,111 @@ +/* +* Copyright (c) 2015 NVIDIA Corporation. All rights reserved. +* +* Permission is hereby granted, free of charge, to any person +obtaining a +* copy of this software and associated documentation files (the +"Software"), +* to deal in the Software without restriction, including without +limitation +* the rights to use, copy, modify, merge, publish, distribute, sub +license, +* and/or sell copies of the Software, and to permit persons to whom +the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including +the +* next paragraph) shall be included in all copies or substantial +portions +* of the Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT +SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES +OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, +ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR +OTHER +* DEALINGS IN THE SOFTWARE. +*/ + +#include <linux/slab.h> + +#include <drm/drm_scdc_helper.h> + +/** +* DOC: scdc helpers +* +* Status and Control Data Channel (SCDC) is a mechanism introduced +by the +* HDMI 2.0 specification. It is a point-to-point protocol that +allows the +* HDMI source and HDMI sink to exchange data. The same I2C interface +that +* is used to access EDID serves as the transport mechanism for SCDC. +*/ + +#define SCDC_I2C_SLAVE_ADDRESS 0x54 + +/** +* drm_scdc_read - read a block of data from SCDC +* @adapter: I2C controller +* @offset: start offset of block to read +* @buffer: return location for the block to read +* @size: size of the block to read +* +* Reads a block of data from SCDC, starting at a given offset. +* +* Returns: +* The number of bytes read from SCDC or a negative error code on failure. +*/ +ssize_t drm_scdc_read (struct i2c_adapter *adapter,u8 offset,void *buffer, +size_t size) +{ +struct i2c_msg msgs[2 ] = { + { + .addr =SCDC_I2C_SLAVE_ADDRESS , + .flags =0 , + .len =1 , + .buf = &offset, + }, { + .addr =SCDC_I2C_SLAVE_ADDRESS , + .flags =I2C_M_RD , + .len = size, + .buf = buffer, + } + }; + +return i2c_transfer (adapter, msgs,ARRAY_SIZE (msgs)); } +EXPORT_SYMBOL (drm_scdc_read); + +/** +* drm_scdc_write - write a block of data to SCDC +* @adapter: I2C controller +* @offset: start offset of block to write +* @buffer: block of data to write +* @size: size of the block to write +* +* Writes a block of data to SCDC, starting at a given offset. +* +* Returns: +* The number of bytes written to SCDC or a negative error code on failure. +*/ +ssize_t drm_scdc_write (struct i2c_adapter *adapter,u8 offset, +const void *buffer,size_t size) { +struct i2c_msg msg = { + .addr =SCDC_I2C_SLAVE_ADDRESS , + .flags =0 , + .len =1 + size, + .buf =NULL , + }; +void *data; +int err; + + data =kmalloc (1 + size,GFP_TEMPORARY ); +if (!data) +return -ENOMEM ; + + msg.buf = data; + +memcpy (data, &offset,sizeof (offset)); +memcpy (data +1 , buffer, size); + + err =i2c_transfer (adapter, &msg,1 ); + +kfree (data); + +return err; +} +EXPORT_SYMBOL (drm_scdc_write);(quoted diff) +0
-0
b/include/drm/drm_scdc_helper.hnew file mode 100644 index 0000000..93b07bcinclude/drm/drm_scdc_helper.h new file +134
-0@@ -0,0 +1,132 @@ +/* +* Copyright (c) 2015 NVIDIA Corporation. All rights reserved. +* +* Permission is hereby granted, free of charge, to any person +obtaining a +* copy of this software and associated documentation files (the +"Software"), +* to deal in the Software without restriction, including without +limitation +* the rights to use, copy, modify, merge, publish, distribute, sub +license, +* and/or sell copies of the Software, and to permit persons to whom +the +* Software is furnished to do so, subject to the following conditions: +* +* The above copyright notice and this permission notice (including +the +* next paragraph) shall be included in all copies or substantial +portions +* of the Software. +* +* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, +EXPRESS OR +* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +MERCHANTABILITY, +* FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT +SHALL +* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES +OR OTHER +* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, +ARISING +* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR +OTHER +* DEALINGS IN THE SOFTWARE. +*/ + +#ifndef DRM_SCDC_HELPER_H +#define DRM_SCDC_HELPER_H + +#include <linux/i2c.h> +#include <linux/types.h> + +#define SCDC_SINK_VERSION 0x01 + +#define SCDC_SOURCE_VERSION 0x02 + +#define SCDC_UPDATE_0 0x10 +#define SCDC_READ_REQUEST_TEST (1 << 2) #define SCDC_CED_UPDATE (1 +<< 1) #define SCDC_STATUS_UPDATE (1 << 0) + +#define SCDC_UPDATE_1 0x11 + +#define SCDC_TMDS_CONFIG 0x20 +#define SCDC_TMDS_BIT_CLOCK_RATIO_BY_40 (1 << 1) #define +SCDC_TMDS_BIT_CLOCK_RATIO_BY_10 (0 << 1) #define +SCDC_SCRAMBLING_ENABLE (1 << 0) + +#define SCDC_SCRAMBLER_STATUS 0x21 +#define SCDC_SCRAMBLING_STATUS (1 << 0) + +#define SCDC_CONFIG_0 0x30 +#define SCDC_READ_REQUEST_ENABLE (1 << 0) + +#define SCDC_STATUS_FLAGS_0 0x40 +#define SCDC_CH2_LOCK (1 < 3) +#define SCDC_CH1_LOCK (1 < 2) +#define SCDC_CH0_LOCK (1 < 1) +#define SCDC_CH_LOCK_MASK (SCDC_CH2_LOCK | SCDC_CH1_LOCK | +SCDC_CH0_LOCK) #define SCDC_CLOCK_DETECT (1 << 0) + +#define SCDC_STATUS_FLAGS_1 0x41 + +#define SCDC_ERR_DET_0_L 0x50 +#define SCDC_ERR_DET_0_H 0x51 +#define SCDC_ERR_DET_1_L 0x52 +#define SCDC_ERR_DET_1_H 0x53 +#define SCDC_ERR_DET_2_L 0x54 +#define SCDC_ERR_DET_2_H 0x55 +#define SCDC_CHANNEL_VALID (1 << 7) + +#define SCDC_ERR_DET_CHECKSUM 0x56 + +#define SCDC_TEST_CONFIG_0 0xc0 +#define SCDC_TEST_READ_REQUEST (1 << 7) #define +SCDC_TEST_READ_REQUEST_DELAY(x) ((x) & 0x7f) + +#define SCDC_MANUFACTURER_IEEE_OUI 0xd0 #define +SCDC_MANUFACTURER_IEEE_OUI_SIZE 3 + +#define SCDC_DEVICE_ID 0xd3 +#define SCDC_DEVICE_ID_SIZE 8 + +#define SCDC_DEVICE_HARDWARE_REVISION 0xdb #define +SCDC_DEVICE_HARDWARE_REVISION_MAJOR(x) (((x) >> 4) & 0xf) #define +SCDC_DEVICE_HARDWARE_REVISION_MINOR (x) (((x) >> 0) & 0xf) + +#define SCDC_DEVICE_SOFTWARE_MAJOR_REVISION 0xdc #define +SCDC_DEVICE_SOFTWARE_MINOR_REVISION 0xdd + +#define SCDC_MANUFACTURER_SPECIFIC 0xde #define +SCDC_MANUFACTURER_SPECIFIC_SIZE 34 + +ssize_t drm_scdc_read (struct i2c_adapter *adapter,u8 offset,void *buffer, +size_t size); +ssize_t drm_scdc_write (struct i2c_adapter *adapter,u8 offset, +const void *buffer,size_t size); + +/** +* drm_scdc_readb - read a single byte from SCDC +* @adapter: I2C adapter +* @offset: offset of register to read +* @value: return location for the register value +* +* Reads a single byte from SCDC. This is a convenience wrapper +around the +* drm_scdc_read() function. +* +* Returns: +* 0 on success or a negative error code on failure. +*/ +static inline int drm_scdc_readb (struct i2c_adapter *adapter,u8 offset, +u8 *value) +{ +return drm_scdc_read (adapter, offset, value,sizeof (*value)); } + +/** +* drm_scdc_writeb - write a single byte to SCDC +* @adapter: I2C adapter +* @offset: offset of register to read +* @value: return location for the register value +* +* Writes a single byte to SCDC. This is a convenience wrapper around +the +* drm_scdc_write() function.
include/drm/drm_scdc_helper.h line 132
Quoted 10 lines
include/drm/drm_scdc_helper.h new file +10
-0+* +* Returns: +* 0 on success or a negative error code on failure. +*/ +static inline int drm_scdc_writeb (struct i2c_adapter *adapter,u8 offset, +u8 value) +{ +return drm_scdc_write (adapter, offset, &value,sizeof (value)); } + +#endif
--
Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/6 drm/edid: check for HF-VSDB block
In reply to Shashank SharmaFrom: Thierry Reding <[email protected]>
This patch implements a small function that finds if a given CEA db is hdmi-forum vendor specific data block or not.
--- drivers/gpu/drm/drm_edid.c | 15 +++++++++++++++ include/linux/hdmi.h | 1 + 2 files changed, 16 insertions(+)
drivers/gpu/drm/drm_edid.c +15 -0
@@ -3239,6 +3239,21 @@ static bool cea_db_is_hdmi_vsdb(const u8 *db)return hdmi_id ==HDMI_IEEE_OUI ; } +static bool cea_db_is_hdmi_forum_vsdb (const u8 *db) +{ +unsigned int oui; + +if (cea_db_tag (db) !=VENDOR_BLOCK ) +return false; + +if (cea_db_payload_len (db) <7 ) +return false; + + oui = db[3 ] <<16 | db[2 ] <<8 | db[1 ]; + +return oui ==HDMI_FORUM_IEEE_OUI ; +} +#define for_each_cea_db (cea, i, start, end) \ for ((i) = (start); (i) < (end) && (i) + cea_db_payload_len(&(cea)[(i)]) < (end); (i) += cea_db_payload_len(&(cea)[(i)]) + 1)
include/linux/hdmi.h +1 -0
@@ -35,6 +35,7 @@ enum hdmi_infoframe_type { };#define HDMI_IEEE_OUI 0x000c03 +#define HDMI_FORUM_IEEE_OUI 0xc45dd8#define HDMI_INFOFRAME_HEADER_SIZE 4#define HDMI_AVI_INFOFRAME_SIZE 13#define HDMI_SPD_INFOFRAME_SIZE 25
Signature · 6 lines
1.9.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH 3/6 drm/edid: detect SCDC support in HF-VSDB
In reply to Shashank SharmaThis patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advance HDMI 2.0 features
- Checks the HF-VSDB block for presence of SCDC, and marks it in hdmi_info structure.
- If SCDC is present, checks if sink is capable of generating scdc read request, and marks it in hdmi_info structure.
--- drivers/gpu/drm/drm_edid.c | 14 ++++++++++++++ include/drm/drm_connector.h | 26 ++++++++++++++++++++++++++ 2 files changed, 40 insertions(+)
drivers/gpu/drm/drm_edid.c +14 -0
@@ -3802,6 +3802,18 @@ enum hdmi_quantization_range }EXPORT_SYMBOL (drm_default_rgb_quant_range); +static void drm_detect_hdmi_scdc (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_hdmi_info *hdmi = &connector->display_info.hdmi_info; + +if (hf_vsdb[6 ] &0x80 ) { + hdmi->scdc_supported = true; +if (hf_vsdb[6 ] &0x40 ) + hdmi->scdc_rr = true; + } +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {
@@ -3916,6 +3928,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); +if (cea_db_is_hdmi_forum_vsdb (db)) +drm_detect_hdmi_scdc (connector, db); } }
include/drm/drm_connector.h +26 -0
@@ -87,6 +87,27 @@ enum subpixel_order { SubPixelVerticalRGB, SubPixelVerticalBGR, SubPixelNone, + +}; + +/** +* struct drm_hdmi_info - runtime data about the connected sink +* +* Describes if a given hdmi display supports advance HDMI 2.0 featutes. +* This information is available in CEA-861-F extension blocks (like +* HF-VSDB) +* For sinks which provide an EDID this can be filled out by calling +* drm_add_edid_modes(). +*/ +struct drm_hdmi_info { +/** +* @scdc_supported: status control & data channel present. +*/ +bool scdc_supported; +/** +* @scdc_rr: sink is capable of generating scdc read request. +*/ +bool scdc_rr; };/**
@@ -188,6 +209,11 @@ struct drm_display_info {* @cea_rev: CEA revision of the HDMI sink. */ u8 cea_rev; + +/** +* @hdmi_info: advance features of a HDMI sink. +*/ +struct drm_hdmi_info hdmi_info; }; int drm_display_info_set_bus_formats(struct drm_display_info *info,
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 3/6] drm/edid: detect SCDC support in HF-VSDB
Quoted 4 lines · Shashank Sharma
This patch does following:
- Adds a new structure (drm_hdmi_info) indrm_display_info. This structure will be used to save and indicate if sink supports advance HDMI 2.0 features
"advanced"
Quoted 2 lines
- Checks the HF-VSDB block for presence of SCDC, and marks it in
hdmi_infostructure.
"drm_hdmi_info structure"?
Quoted 2 lines
- If SCDC is present, checks if sink is capable of generating scdc read request, and marks it in
hdmi_infostructure.
"SCDC" to be consistent and because it's an abbreviation.
Quoted 44 lines
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 14 ++++++++++++++ include/drm/drm_connector.h | 26 ++++++++++++++++++++++++++ 2 files changed, 40 insertions(+)drivers/gpu/drm/drm_edid.c +14
-0@@ -3802,6 +3802,18 @@ enum hdmi_quantization_range }EXPORT_SYMBOL (drm_default_rgb_quant_range); +static void drm_detect_hdmi_scdc (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_hdmi_info *hdmi = &connector->display_info.hdmi_info; + +if (hf_vsdb[6 ] &0x80 ) { + hdmi->scdc_supported = true; +if (hf_vsdb[6 ] &0x40 ) + hdmi->scdc_rr = true; + } +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3916,6 +3928,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); +if (cea_db_is_hdmi_forum_vsdb (db)) +drm_detect_hdmi_scdc (connector, db); } }include/drm/drm_connector.h +0
-0
include/drm/drm_connector.h enum subpixel_order { · line 94
Quoted 8 lines
include/drm/drm_connector.h +5
-0@@ -87,6 +87,27 @@ enum subpixel_order { SubPixelVerticalRGB, SubPixelVerticalBGR, SubPixelNone, + +}; + +/** +* struct drm_hdmi_info - runtime data about the connected sink
Maybe "connected HDMI sink"?
include/drm/drm_connector.h enum subpixel_order { · line 96
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* +* Describes if a given hdmi display supports advance HDMI 2.0 featutes.
"HDMI", "advanced", "features"
include/drm/drm_connector.h enum subpixel_order { · line 98
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* This information is available in CEA-861-F extension blocks (like +* HF-VSDB)
This should be terminated by a full-stop.
include/drm/drm_connector.h enum subpixel_order { · line 100
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* For sinks which provide an EDID this can be filled out by calling +* drm_add_edid_modes().
And maybe make this sentence start right after the one above rather than breaking it to the next line. I'm not sure how useful this line is. Most driver will be calling drm_add_edid_modes() anyway, but the above makes it sound like drm_add_edid_modes() is something you have to explicitly call to get these fields parsed.
Quoted 14 lines
include/drm/drm_connector.h +10
-0+*/ +struct drm_hdmi_info { +/** +* @scdc_supported: status control & data channel present. +*/ +bool scdc_supported; +/** +* @scdc_rr: sink is capable of generating scdc read request. +*/ +bool scdc_rr; };/**
include/drm/drm_connector.h struct drm_display_info { · line 216
Quoted 8 lines
include/drm/drm_connector.h +5
-0@@ -188,6 +209,11 @@ struct drm_display_info {* @cea_rev: CEA revision of the HDMI sink. */ u8 cea_rev; + +/** +* @hdmi_info: advance features of a HDMI sink. +*/ +struct drm_hdmi_info hdmi_info;
I think we can safely drop the _info suffix on the field name. It's already inside a structure that carries this suffix.
Other than that:
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 3/6] drm/edid: detect SCDC support in HF-VSDB
Thanks for the review Thierry. My comments inline.
Regards
Shashank
Quoted 6 lines · Thierry Reding
Quoted 4 lines · Shashank Sharma
This patch does following:
- Adds a new structure (drm_hdmi_info) indrm_display_info. This structure will be used to save and indicate if sink supports advance HDMI 2.0 features"advanced"
got it.
Quoted 4 lines
Quoted 3 lines
- Checks the HF-VSDB block for presence of SCDC, and marks it in
hdmi_infostructure."
drm_hdmi_infostructure"?
yep, sure.
Quoted 3 lines
Quoted 2 lines
- If SCDC is present, checks if sink is capable of generating scdc read request, and marks it in
hdmi_infostructure."SCDC" to be consistent and because it's an abbreviation.
Agree.
Quoted 38 lines
Quoted 38 lines
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 14 ++++++++++++++ include/drm/drm_connector.h | 26 ++++++++++++++++++++++++++ 2 files changed, 40 insertions(+)drivers/gpu/drm/drm_edid.c +14
-0@@ -3802,6 +3802,18 @@ enum hdmi_quantization_range }EXPORT_SYMBOL (drm_default_rgb_quant_range); +static void drm_detect_hdmi_scdc (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_hdmi_info *hdmi = &connector->display_info.hdmi_info; + +if (hf_vsdb[6 ] &0x80 ) { + hdmi->scdc_supported = true; +if (hf_vsdb[6 ] &0x40 ) + hdmi->scdc_rr = true; + } +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3916,6 +3928,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); +if (cea_db_is_hdmi_forum_vsdb (db)) +drm_detect_hdmi_scdc (connector, db); } }
Quoted 14 lines
include/drm/drm_connector.h enum subpixel_order { · line 94
Quoted 13 lines
include/drm/drm_connector.h +5
-0@@ -87,6 +87,27 @@ enum subpixel_order { SubPixelVerticalRGB, SubPixelVerticalBGR, SubPixelNone, + +}; + +/** +* struct drm_hdmi_info - runtime data about the connected sink Maybe "connected HDMI sink"?
Agree.
Quoted 3 lines
include/drm/drm_connector.h enum subpixel_order { · line 96
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* +* Describes if a given hdmi display supports advance HDMI 2.0 featutes. "HDMI", "advanced", "features"
Oops, got it :-)
Quoted 3 lines
include/drm/drm_connector.h enum subpixel_order { · line 98
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* This information is available in CEA-861-F extension blocks (like +* HF-VSDB) This should be terminated by a full-stop.
Ok
Quoted 4 lines
include/drm/drm_connector.h enum subpixel_order { · line 100
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* For sinks which provide an EDID this can be filled out by calling +* drm_add_edid_modes(). And maybe make this sentence start right after the one above rather than breaking it to the next line.
Ok
Quoted 4 lines
I'm not sure how useful this line is. Most
driver will be callingdrm_add_edid_modes()anyway, but the above makes it sound likedrm_add_edid_modes()is something you have to explicitly call to get these fields parsed.
Mostly a 'yy' and 'p' from the function above, but makes sense, I can remove this line.
Quoted 12 lines
Quoted 12 lines
include/drm/drm_connector.h +10
-0+*/ +struct drm_hdmi_info { +/** +* @scdc_supported: status control & data channel present. +*/ +bool scdc_supported; +/** +* @scdc_rr: sink is capable of generating scdc read request. +*/ +bool scdc_rr; };
Quoted 12 lines
include/drm/drm_connector.h struct drm_display_info { · line 216
Quoted 10 lines
include/drm/drm_connector.h +5
-0/** @@ -188,6 +209,11 @@ struct drm_display_info {* @cea_rev: CEA revision of the HDMI sink. */ u8 cea_rev; + +/** +* @hdmi_info: advance features of a HDMI sink. +*/ +struct drm_hdmi_info hdmi_info;I think we can safely drop the
_infosuffix on the field name. It's already inside a structure that carries this suffix.
Sure, should I call it hdmi_sink OR connected_hdmi ?
- Shashank
Quoted 4 lines
Other than that:
Reviewed-by Thierry Reding <[email protected]>
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 3/6] drm/edid: detect SCDC support in HF-VSDB
Quoted 113 lines · Shashank
Thanks for the review Thierry. My comments inline.
Regards
ShashankQuoted 6 lines · Thierry Reding
Quoted 4 lines · Shashank Sharma
This patch does following:
- Adds a new structure (drm_hdmi_info) indrm_display_info. This structure will be used to save and indicate if sink supports advance HDMI 2.0 features"advanced"
got it.
Quoted 4 lines
Quoted 3 lines
- Checks the HF-VSDB block for presence of SCDC, and marks it in
hdmi_infostructure."
drm_hdmi_infostructure"?yep, sure.
Quoted 3 lines
Quoted 2 lines
- If SCDC is present, checks if sink is capable of generating scdc read request, and marks it in
hdmi_infostructure."SCDC" to be consistent and because it's an abbreviation.
Agree.
Quoted 41 lines
Quoted 41 lines
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 14 ++++++++++++++ include/drm/drm_connector.h | 26 ++++++++++++++++++++++++++ 2 files changed, 40 insertions(+)drivers/gpu/drm/drm_edid.c +14
-0@@ -3802,6 +3802,18 @@ enum hdmi_quantization_range }EXPORT_SYMBOL (drm_default_rgb_quant_range); +static void drm_detect_hdmi_scdc (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_hdmi_info *hdmi = &connector->display_info.hdmi_info; + +if (hf_vsdb[6 ] &0x80 ) { + hdmi->scdc_supported = true; +if (hf_vsdb[6 ] &0x40 ) + hdmi->scdc_rr = true; + } +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3916,6 +3928,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); +if (cea_db_is_hdmi_forum_vsdb (db)) +drm_detect_hdmi_scdc (connector, db); } }include/drm/drm_connector.h +0
-0@@ -87,6 +87,27 @@ enum subpixel_order { SubPixelVerticalRGB,Quoted 8 lines
include/drm/drm_connector.h enum subpixel_order { · line 94
Quoted 7 lines
include/drm/drm_connector.h +5
-0SubPixelVerticalBGR, SubPixelNone, + +}; + +/** +* struct drm_hdmi_info - runtime data about the connected sink Maybe "connected HDMI sink"?
Agree.
Quoted 3 lines
include/drm/drm_connector.h enum subpixel_order { · line 96
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* +* Describes if a given hdmi display supports advance HDMI 2.0 featutes. "HDMI", "advanced", "features"
Oops, got it :-)
Quoted 3 lines
include/drm/drm_connector.h enum subpixel_order { · line 98
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* This information is available in CEA-861-F extension blocks (like +* HF-VSDB) This should be terminated by a full-stop.
Ok
Quoted 4 lines
include/drm/drm_connector.h enum subpixel_order { · line 100
Quoted 2 lines
include/drm/drm_connector.h +2
-0+* For sinks which provide an EDID this can be filled out by calling +* drm_add_edid_modes(). And maybe make this sentence start right after the one above rather than breaking it to the next line.
Ok
Quoted 4 lines
I'm not sure how useful this line is. Most
driver will be callingdrm_add_edid_modes()anyway, but the above makes it sound likedrm_add_edid_modes()is something you have to explicitly call to get these fields parsed.Mostly a 'yy' and 'p' from the function above, but makes sense, I can remove this line.
Quoted 15 lines
Quoted 15 lines
include/drm/drm_connector.h +10
-0+*/ +struct drm_hdmi_info { +/** +* @scdc_supported: status control & data channel present. +*/ +bool scdc_supported; +/** +* @scdc_rr: sink is capable of generating scdc read request. +*/ +bool scdc_rr; };/** @@ -188,6 +209,11 @@ struct drm_display_info {* @cea_rev: CEA revision of the HDMI sink. */ Quoted 8 lines
include/drm/drm_connector.h struct drm_display_info { · line 216
Quoted 6 lines
include/drm/drm_connector.h +5
-0u8 cea_rev; + +/** +* @hdmi_info: advance features of a HDMI sink. +*/ +struct drm_hdmi_info hdmi_info;I think we can safely drop the
_infosuffix on the field name. It's already inside a structure that carries this suffix.
Quoted 1 line
Sure, should I call it
hdmi_sinkORconnected_hdmi?
No, I think just plain "hdmi" would be fine. This is part of drm_display_info, which kind of implies that it's a sink, and I think it's also fair to assume that this isn't valid if nothing's connected.
Thierry
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 3/6] drm/edid: detect SCDC support in HF-VSDB
In reply to Shashank SharmaQuoted 66 lines · Shashank Sharma
This patch does following:
- Adds a new structure (drm_hdmi_info) indrm_display_info. This structure will be used to save and indicate if sink supports advance HDMI 2.0 features
- Checks the HF-VSDB block for presence of SCDC, and marks it inhdmi_infostructure.
- If SCDC is present, checks if sink is capable of generating scdc read request, and marks it inhdmi_infostructure.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 14 ++++++++++++++ include/drm/drm_connector.h | 26 ++++++++++++++++++++++++++ 2 files changed, 40 insertions(+)drivers/gpu/drm/drm_edid.c +14
-0@@ -3802,6 +3802,18 @@ enum hdmi_quantization_range }EXPORT_SYMBOL (drm_default_rgb_quant_range); +static void drm_detect_hdmi_scdc (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_hdmi_info *hdmi = &connector->display_info.hdmi_info; + +if (hf_vsdb[6 ] &0x80 ) { + hdmi->scdc_supported = true; +if (hf_vsdb[6 ] &0x40 ) + hdmi->scdc_rr = true; + } +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3916,6 +3928,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); +if (cea_db_is_hdmi_forum_vsdb (db)) +drm_detect_hdmi_scdc (connector, db); } }include/drm/drm_connector.h +11
-0@@ -87,6 +87,27 @@ enum subpixel_order { SubPixelVerticalRGB, SubPixelVerticalBGR, SubPixelNone, + +}; + +/** +* struct drm_hdmi_info - runtime data about the connected sink +* +* Describes if a given hdmi display supports advance HDMI 2.0 featutes. +* This information is available in CEA-861-F extension blocks (like +* HF-VSDB) +* For sinks which provide an EDID this can be filled out by calling +* drm_add_edid_modes().
include/drm/drm_connector.h enum subpixel_order { · line 110
Quoted 10 lines
include/drm/drm_connector.h +10
-0+*/ +struct drm_hdmi_info { +/** +* @scdc_supported: status control & data channel present. +*/ +bool scdc_supported; +/** +* @scdc_rr: sink is capable of generating scdc read request. +*/ +bool scdc_rr;
Probably worth spelling the thing out.
Quoted 17 lines
include/drm/drm_connector.h +5
-0};/** @@ -188,6 +209,11 @@ struct drm_display_info {* @cea_rev: CEA revision of the HDMI sink. */ u8 cea_rev; + +/** +* @hdmi_info: advance features of a HDMI sink. +*/ +struct drm_hdmi_info hdmi_info; }; int drm_display_info_set_bus_formats(struct drm_display_info *info,Signature · 1 line
1.9.1
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 3/6] drm/edid: detect SCDC support in HF-VSDB
Thanks for the review Ville. My comments inline.
Regards
Shashank
Quoted 70 lines · Ville Syrjälä
Quoted 69 lines · Shashank Sharma
This patch does following:
- Adds a new structure (drm_hdmi_info) indrm_display_info. This structure will be used to save and indicate if sink supports advance HDMI 2.0 features
- Checks the HF-VSDB block for presence of SCDC, and marks it inhdmi_infostructure.
- If SCDC is present, checks if sink is capable of generating scdc read request, and marks it inhdmi_infostructure.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 14 ++++++++++++++ include/drm/drm_connector.h | 26 ++++++++++++++++++++++++++ 2 files changed, 40 insertions(+)drivers/gpu/drm/drm_edid.c +14
-0@@ -3802,6 +3802,18 @@ enum hdmi_quantization_range }EXPORT_SYMBOL (drm_default_rgb_quant_range); +static void drm_detect_hdmi_scdc (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_hdmi_info *hdmi = &connector->display_info.hdmi_info; + +if (hf_vsdb[6 ] &0x80 ) { + hdmi->scdc_supported = true; +if (hf_vsdb[6 ] &0x40 ) + hdmi->scdc_rr = true; + } +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3916,6 +3928,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); +if (cea_db_is_hdmi_forum_vsdb (db)) +drm_detect_hdmi_scdc (connector, db); } }include/drm/drm_connector.h +14
-0@@ -87,6 +87,27 @@ enum subpixel_order { SubPixelVerticalRGB, SubPixelVerticalBGR, SubPixelNone, + +}; + +/** +* struct drm_hdmi_info - runtime data about the connected sink +* +* Describes if a given hdmi display supports advance HDMI 2.0 featutes. +* This information is available in CEA-861-F extension blocks (like +* HF-VSDB) +* For sinks which provide an EDID this can be filled out by calling +* drm_add_edid_modes(). +*/ +struct drm_hdmi_info { +/**
Quoted 8 lines
include/drm/drm_connector.h enum subpixel_order { · line 110
Quoted 7 lines
include/drm/drm_connector.h +7
-0+* @scdc_supported: status control & data channel present. +*/ +bool scdc_supported; +/** +* @scdc_rr: sink is capable of generating scdc read request. +*/ +bool scdc_rr;Probably worth spelling the thing out.
Agree. I was afraid it would make it difficult for 80 char stuff, but maybe I can make it scdc->read_req
- Shashank
Quoted 14 lines
Quoted 14 lines
include/drm/drm_connector.h +5
-0};/** @@ -188,6 +209,11 @@ struct drm_display_info {* @cea_rev: CEA revision of the HDMI sink. */ u8 cea_rev; + +/** +* @hdmi_info: advance features of a HDMI sink. +*/ +struct drm_hdmi_info hdmi_info; };
Quoted 3 lines
Quoted 3 lines
include/drm/drm_connector.h +0
-0int drm_display_info_set_bus_formats(struct drm_display_info *info,Signature · 1 line
1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH 4/6 drm: scrambling support in drm layer
In reply to Shashank SharmaHDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.
--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)
drivers/gpu/drm/drm_edid.c +130 -1
@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \
@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M. +* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ; +DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock); + +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true; + } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel +* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. +*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter) +{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) { +DRM_ERROR ("Failed to read scrambling status\n" ); +return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ; +} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling +* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {
@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }
include/drm/drm_connector.h +24 -0
@@ -90,6 +90,26 @@ enum subpixel_order { }; + +/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. +*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks; +/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink *
@@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. */ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info; };/**
include/drm/drm_edid.h +5 -1
@@ -462,5 +462,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,struct drm_display_mode *drm_mode_find_dmt (struct drm_device *dev,int hsize,int vsize,int fresh,bool rb); - +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_check_scrambling_status (struct i2c_adapter *adapter);#endif /* __DRM_EDID_H__ */
Signature · 6 lines
1.9.1 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/6] drm: scrambling support in drm layer
Quoted 31 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, }
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3825
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +8
-0} +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M.
In comments below you use Mhz as the abbreviations. This should be consistent. Also I think "MHz" is actually the correct spelling.
Quoted 15 lines
drivers/gpu/drm/drm_edid.c +15
-0+* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ; +DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock); + +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; +
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3850
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true; + } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel
"I2C", same in other parts of this patch.
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3855
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise.
I think the rest of DRM/KMS kerneldoc tries to use "Returns:\n" as a standard way to document return values.
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3858
Quoted 3 lines
drivers/gpu/drm/drm_edid.c +3
-0+*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter)
Maybe use a drm_scdc_*() prefix for this to make it more consistent with other SCDC API.
While at it, would this not be better located in drm_scdc.c along with the other helpers? drm_edid.c is more focussed on the parsing aspects of all things EDID.
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3862
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) {
How about storing the error code...
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3863
Quoted 1 line
drivers/gpu/drm/drm_edid.c +1
-0+DRM_ERROR ("Failed to read scrambling status\n" );
... and making it part of the error message? Sometimes its useful to know what exact error triggered this because it helps narrowing down where things went wrong.
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3868
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ;
Maybe make this a single line:
return (status & SCDC_SCRAMBLING_STATUS) != 0;
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3873
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector
"target DRM connector"?
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3882
Quoted 9 lines
drivers/gpu/drm/drm_edid.c +9
-0+* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling +* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force)
I think I'd move this to drm_scdc.c as well because it primarily operates on SCDC. If you do so, might be worth making adapter the first argument for consistency with other SCDC API.
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3893
Quoted 11 lines
drivers/gpu/drm/drm_edid.c +11
-0+{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" );
Maybe also print the error code?
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3900
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" );
Same here.
Quoted 32 lines
drivers/gpu/drm/drm_edid.c +32
-0+return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } +
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3942
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+ config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +}
Same comments as for drm_enable_scrambling().
Quoted 17 lines
drivers/gpu/drm/drm_edid.c +3
-1@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +0
-0
include/drm/drm_connector.h enum subpixel_order { · line 99
Quoted 10 lines
include/drm/drm_connector.h +7
-0@@ -90,6 +90,26 @@ enum subpixel_order { }; + +/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz.
I think it's common to separate number and unit by a space, so "340 MHz".
include/drm/drm_connector.h enum subpixel_order { · line 105
Quoted 6 lines
include/drm/drm_connector.h +6
-0+*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks;
Maybe "low_rates" because a clock is technically the source of a signal that oscillates at the given rate.
Quoted 11 lines
include/drm/drm_connector.h +7
-0+/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink *
include/drm/drm_connector.h struct drm_hdmi_info { · line 134
Quoted 7 lines
include/drm/drm_connector.h +4
-0@@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. */ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info;
Again, I think I'd drop _info and instead spell out "scrambling" to make this easier to remember.
Also I'm wondering why scdc_supported and scdc_rr are not in a structure if scrambling info is. Also since scrambling depends on SCDC, would it make sense to embed it in a struct drm_hdmi_scdc_info?
struct drm_hdmi_scdc_scrambling_info {
bool supported;
bool low_rates;
bool status;
};
struct drm_hdmi_scdc_info {
bool supported;
bool read_request;
struct drm_hdmi_scdc_scrambling_info scrambling;
};Thierry
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/6] drm: scrambling support in drm layer
Regards
Shashank
Quoted 34 lines · Thierry Reding
Quoted 33 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } }
Quoted 10 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3825
Quoted 8 lines
drivers/gpu/drm/drm_edid.c +8
-0+static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M. In comments below you use Mhz as the abbreviations. This should be consistent. Also I think "MHz" is actually the correct spelling.
Agree.
Quoted 18 lines
Quoted 18 lines
drivers/gpu/drm/drm_edid.c +18
-0+* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ; +DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock); + +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true;
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3850
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+ } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel "I2C", same in other parts of this patch.
Got it.
Quoted 7 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3855
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. I think the rest of DRM/KMS kerneldoc tries to use "Returns:\n" as a standard way to document return values.
Ok.
Quoted 9 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3858
Quoted 3 lines
drivers/gpu/drm/drm_edid.c +3
-0+*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter)Maybe use a drm_scdc_*() prefix for this to make it more consistent with other SCDC API.
While at it, would this not be better located in
drm_scdc.calong with the other helpers?drm_edid.cis more focussed on the parsing aspects of all things EDID.
Yeah, the same is mentioned by Ville too, will do that.
Quoted 10 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3862
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) {How about storing the error code...
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3863
Quoted 1 line
drivers/gpu/drm/drm_edid.c +1
-0+DRM_ERROR ("Failed to read scrambling status\n" );... and making it part of the error message? Sometimes its useful to know what exact error triggered this because it helps narrowing down where things went wrong.
Agree, in fact while debugging and testing this patch series, I had to print it explicitly.
Quoted 9 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3868
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +5
-0+return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ;Maybe make this a single line:
return (status & SCDC_SCRAMBLING_STATUS) != 0;
Got it.
Quoted 7 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3873
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +5
-0+} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector "target DRM connector"?
Got it.
Quoted 4 lines
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3882
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force)I think I'd move this to
drm_scdc.cas well because it primarily operates on SCDC. If you do so, might be worth making adapter the first argument for consistency with other SCDC API.
Agree, will move it.
Quoted 4 lines
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3893
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" );Maybe also print the error code?
Ok.
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3900
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" );Same here.
Ok
Quoted 35 lines
Quoted 35 lines
drivers/gpu/drm/drm_edid.c +35
-0+return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) {
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3942
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +}Same comments as for
drm_enable_scrambling().
Got it.
Quoted 20 lines
Quoted 20 lines
drivers/gpu/drm/drm_edid.c +3
-1@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +0
-0@@ -90,6 +90,26 @@ enum subpixel_order { };
Quoted 9 lines
include/drm/drm_connector.h enum subpixel_order { · line 99
Quoted 7 lines
include/drm/drm_connector.h +7
-0+ +/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. I think it's common to separate number and unit by a space, so "340 MHz".
Got it.
Quoted 8 lines
include/drm/drm_connector.h enum subpixel_order { · line 105
Quoted 6 lines
include/drm/drm_connector.h +6
-0+*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks;Maybe "
low_rates" because a clock is technically the source of a signal that oscillates at the given rate.
Agree, will change it.
Quoted 12 lines
Quoted 12 lines
include/drm/drm_connector.h +7
-0+/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink * @@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request.
Quoted 8 lines
include/drm/drm_connector.h struct drm_hdmi_info { · line 134
Quoted 6 lines
include/drm/drm_connector.h +4
-0*/ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info;Again, I think I'd drop
_infoand instead spell out "scrambling" to make this easier to remember.
Sure, can be done.
Quoted 4 lines
Also I'm wondering why
scdc_supportedandscdc_rrare not in a structure if scrambling info is. Also since scrambling depends on SCDC, would it make sense to embed it in a structdrm_hdmi_scdc_info?
My opinion while designing was:
- SCDC rr support is platform specific, and a platform can choose not to support read_req but just allow scrambling using scdc read and write, hence kept that separate
- You need to look into this internal structure, only if scdc is supported.
- Also, SCDC registers can be used beyond scrambling too, like for error detection, and other cases, so I thought it would be better to keep it independent.
Does it make sense ?
-Shashank
Quoted 14 lines
struct drm_hdmi_scdc_scrambling_info {
bool supported;
bool low_rates;
bool status;
};
struct drm_hdmi_scdc_info {
bool supported;
bool read_request;
struct drm_hdmi_scdc_scrambling_info scrambling;
};Quoted 1 line
Thierry
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/6] drm: scrambling support in drm layer
Quoted 272 lines · Shashank
Regards
Shashank
Quoted 34 lines · Thierry Reding
Quoted 33 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +3
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3825
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +6
-0+{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M. In comments below you use Mhz as the abbreviations. This should be consistent. Also I think "MHz" is actually the correct spelling.
Agree.
Quoted 18 lines
Quoted 18 lines
drivers/gpu/drm/drm_edid.c +18
-0+* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ; +DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock); + +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true;Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3850
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+ } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel "I2C", same in other parts of this patch.
Got it.
Quoted 7 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3855
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. I think the rest of DRM/KMS kerneldoc tries to use "Returns:\n" as a standard way to document return values.
Ok.
Quoted 9 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3858
Quoted 3 lines
drivers/gpu/drm/drm_edid.c +3
-0+*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter)Maybe use a drm_scdc_*() prefix for this to make it more consistent with other SCDC API.
While at it, would this not be better located in
drm_scdc.calong with the other helpers?drm_edid.cis more focussed on the parsing aspects of all things EDID.Yeah, the same is mentioned by Ville too, will do that.
Quoted 10 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3862
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) {How about storing the error code...
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3863
Quoted 1 line
drivers/gpu/drm/drm_edid.c +1
-0+DRM_ERROR ("Failed to read scrambling status\n" );... and making it part of the error message? Sometimes its useful to know what exact error triggered this because it helps narrowing down where things went wrong.
Agree, in fact while debugging and testing this patch series, I had to print it explicitly.
Quoted 9 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3868
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +5
-0+return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ;Maybe make this a single line:
return (status & SCDC_SCRAMBLING_STATUS) != 0;Got it.
Quoted 7 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3873
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +5
-0+} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector "target DRM connector"?
Got it.
Quoted 4 lines
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3882
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force)I think I'd move this to
drm_scdc.cas well because it primarily operates on SCDC. If you do so, might be worth making adapter the first argument for consistency with other SCDC API.Agree, will move it.
Quoted 4 lines
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3893
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" );Maybe also print the error code?
Ok.
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3900
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" );Same here.
Ok
Quoted 35 lines
Quoted 35 lines
drivers/gpu/drm/drm_edid.c +35
-0+return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) {Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3942
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +}Same comments as for
drm_enable_scrambling().Got it.
Quoted 17 lines
Quoted 17 lines
drivers/gpu/drm/drm_edid.c +3
-1@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +1
-0@@ -90,6 +90,26 @@ enum subpixel_order { }; +Quoted 8 lines
include/drm/drm_connector.h enum subpixel_order { · line 99
Quoted 6 lines
include/drm/drm_connector.h +6
-0+/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. I think it's common to separate number and unit by a space, so "340 MHz".
Got it.
Quoted 8 lines
include/drm/drm_connector.h enum subpixel_order { · line 105
Quoted 6 lines
include/drm/drm_connector.h +6
-0+*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks;Maybe "
low_rates" because a clock is technically the source of a signal that oscillates at the given rate.Agree, will change it.
Quoted 12 lines
Quoted 12 lines
include/drm/drm_connector.h +7
-0+/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink * @@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. Quoted 8 lines
include/drm/drm_connector.h struct drm_hdmi_info { · line 134
Quoted 6 lines
include/drm/drm_connector.h +4
-0*/ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info;Again, I think I'd drop
_infoand instead spell out "scrambling" to make this easier to remember.Sure, can be done.
Quoted 4 lines
Also I'm wondering why
scdc_supportedandscdc_rrare not in a structure if scrambling info is. Also since scrambling depends on SCDC, would it make sense to embed it in a structdrm_hdmi_scdc_info?My opinion while designing was:
- SCDC rr support is platform specific, and a platform can choose not to supportread_reqbut just allow
scrambling using scdc read and write, hence kept that separate
- You need to look into this internal structure, only if scdc is supported.
- Also, SCDC registers can be used beyond scrambling too, like for error detection, and other cases, so I thought
it would be better to keep it independent.
Quoted 1 line
Does it make sense ?
Yes, I think that makes sense, but it's not what I was trying to say. =) What I was trying to say is that read request and scrambling are defined in the SCDC specification, and therefore they require SCDC. That's why I think the below is a natural representation because it captures the dependency in a hierarchy:
Quoted 6 lines
Quoted 6 lines
struct drm_hdmi_scdc_scrambling_info { bool supported; bool low_rates; bool status; };
Quoted 6 lines
Quoted 6 lines
struct drm_hdmi_scdc_info { bool supported; bool read_request; struct drm_hdmi_scdc_scrambling_info scrambling; };
I should have added to the above:
struct drm_hdmi_info {
struct drm_hdmi_scdc_info scdc;
};So when conditionalizing code this allows for a very natural ordering of the code:
struct drm_display_info *info = ...;
struct drm_hdmi_scdc_info *scdc = &info->hdmi.scdc;
if (scdc->supported) {
...
if (scdc->read_request) {
...
e.g. set up handler for read requests
...
}
...
if (scdc->scrambling.supported) {
if (mode->clock >= 340000 || scdc->scrambling.low_rates) {
...
set up scrambling
...;
}
}
...
}Thierry
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/6] drm: scrambling support in drm layer
Regards
Shashank
Quoted 323 lines · Thierry Reding
Quoted 269 lines · Shashank
Regards
Shashank
Quoted 34 lines · Thierry Reding
Quoted 33 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +3
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3825
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +6
-0+{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M. In comments below you use Mhz as the abbreviations. This should be consistent. Also I think "MHz" is actually the correct spelling.
Agree.
Quoted 18 lines
Quoted 18 lines
drivers/gpu/drm/drm_edid.c +18
-0+* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ; +DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock); + +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true;Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3850
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+ } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel "I2C", same in other parts of this patch.
Got it.
Quoted 7 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3855
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. I think the rest of DRM/KMS kerneldoc tries to use "Returns:\n" as a standard way to document return values.
Ok.
Quoted 9 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3858
Quoted 3 lines
drivers/gpu/drm/drm_edid.c +3
-0+*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter)Maybe use a drm_scdc_*() prefix for this to make it more consistent with other SCDC API.
While at it, would this not be better located in
drm_scdc.calong with the other helpers?drm_edid.cis more focussed on the parsing aspects of all things EDID.Yeah, the same is mentioned by Ville too, will do that.
Quoted 10 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3862
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) {How about storing the error code...
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3863
Quoted 1 line
drivers/gpu/drm/drm_edid.c +1
-0+DRM_ERROR ("Failed to read scrambling status\n" );... and making it part of the error message? Sometimes its useful to know what exact error triggered this because it helps narrowing down where things went wrong.
Agree, in fact while debugging and testing this patch series, I had to print it explicitly.
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3868
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ;Maybe make this a single line:
return (status & SCDC_SCRAMBLING_STATUS) != 0;Got it.
Quoted 6 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3873
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector "target DRM connector"?
Got it.
Quoted 4 lines
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3882
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +5
-0+* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force)I think I'd move this to
drm_scdc.cas well because it primarily operates on SCDC. If you do so, might be worth making adapter the first argument for consistency with other SCDC API.Agree, will move it.
Quoted 4 lines
Quoted 4 lines
drivers/gpu/drm/drm_edid.c +4
-0+{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3893
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" );Maybe also print the error code?
Ok.
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3900
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" );Same here.
Ok
Quoted 35 lines
Quoted 35 lines
drivers/gpu/drm/drm_edid.c +35
-0+return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) {Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3942
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +}Same comments as for
drm_enable_scrambling().Got it.
Quoted 17 lines
Quoted 17 lines
drivers/gpu/drm/drm_edid.c +3
-1@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +1
-0@@ -90,6 +90,26 @@ enum subpixel_order { }; +Quoted 8 lines
include/drm/drm_connector.h enum subpixel_order { · line 99
Quoted 6 lines
include/drm/drm_connector.h +6
-0+/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. I think it's common to separate number and unit by a space, so "340 MHz".
Got it.
Quoted 8 lines
include/drm/drm_connector.h enum subpixel_order { · line 105
Quoted 6 lines
include/drm/drm_connector.h +6
-0+*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks;Maybe "
low_rates" because a clock is technically the source of a signal that oscillates at the given rate.Agree, will change it.
Quoted 12 lines
Quoted 12 lines
include/drm/drm_connector.h +7
-0+/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink * @@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. Quoted 8 lines
include/drm/drm_connector.h struct drm_hdmi_info { · line 134
Quoted 6 lines
include/drm/drm_connector.h +4
-0*/ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info;Again, I think I'd drop
_infoand instead spell out "scrambling" to make this easier to remember.Sure, can be done.
Quoted 3 lines
Also I'm wondering why
scdc_supportedandscdc_rrare not in a structure if scrambling info is. Also since scrambling depends on SCDC, would it make sense to embed it in a structdrm_hdmi_scdc_info?My opinion while designing was:
- SCDC rr support is platform specific, and a platform can choose not to supportread_reqbut just allow
scrambling using scdc read and write, hence kept that separate
- You need to look into this internal structure, only if scdc is supported.
- Also, SCDC registers can be used beyond scrambling too, like for error detection, and other cases, so I thought
it would be better to keep it independent.Quoted 1 line
Does it make sense ?
Yes, I think that makes sense, but it's not what I was trying to say. =) What I was trying to say is that read request and scrambling are defined in the SCDC specification, and therefore they require SCDC. That's why I think the below is a natural representation because it captures the dependency in a hierarchy:
Quoted 6 lines
Quoted 6 lines
struct drm_hdmi_scdc_scrambling_info { bool supported; bool low_rates; bool status; };Quoted 6 lines
Quoted 6 lines
struct drm_hdmi_scdc_info { bool supported; bool read_request; struct drm_hdmi_scdc_scrambling_info scrambling; };I should have added to the above:
struct drm_hdmi_info { struct drm_hdmi_scdc_info scdc; };So when conditionalizing code this allows for a very natural ordering of the code:
struct drm_display_info *info = ...; struct drm_hdmi_scdc_info *scdc = &info->hdmi.scdc; if (scdc->supported) { ... if (scdc->read_request) { ... e.g. set up handler for read requests ... } ... if (scdc->scrambling.supported) { if (mode->clock >= 340000 || scdc->scrambling.low_rates) { ... set up scrambling ...; } } ... }
Quoted 1 line
Thierry
Well, makes perfect sense, will change the code as suggested :=)
- Shashank
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/6] drm: scrambling support in drm layer
In reply to Shashank SharmaQuoted 30 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3819
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +2
-0@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)
That names seems off. Should probably be drm_parse_hdmi_forum_vsdb() or something.
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M. +* And as per the spec, three factors confirm this:
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3836
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ; +DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock);
I wonder if we should be a little paranoid and ignore this if it's <=340?
Quoted 12 lines
drivers/gpu/drm/drm_edid.c +12
-0+ +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true; + } + } +} + +/**
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3858
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel +* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. +*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter)
The name is again a little wonky. And it looks like something that should live alognside the SCDC helper stuff.
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3868
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) { +DRM_ERROR ("Failed to read scrambling status\n" ); +return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ;
return status & SCDC_SCRAMBLING_STATUS
Quoted 12 lines
drivers/gpu/drm/drm_edid.c +12
-0+} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling +* Return: True if scrambling is successfully enabled, false otherwise. +*/ +
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3890
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + }
I don't think we want to track any dynamic state in the display info. That belongs to the atomic state stuff.
And the function again looks like something that belongs in the SCDC helper.
Since the two pieces of infromaton in this registrer are the scramble control and the clock ratio, I think we might want to just have one function to configure both.
Quoted 127 lines
drivers/gpu/drm/drm_edid.c +56
-1+ +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +24
-0@@ -90,6 +90,26 @@ enum subpixel_order { }; + +/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. +*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks; +/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink * @@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. */ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info; };/** include/drm/drm_edid.h +5
-1@@ -462,5 +462,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,struct drm_display_mode *drm_mode_find_dmt (struct drm_device *dev,int hsize,int vsize,int fresh,bool rb); - +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_check_scrambling_status (struct i2c_adapter *adapter);#endif /* __DRM_EDID_H__ */ Signature · 1 line
1.9.1
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/6] drm: scrambling support in drm layer
Regards
Shashank
Quoted 34 lines · Ville Syrjälä
Quoted 33 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } }
Quoted 4 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3819
Quoted 2 lines
drivers/gpu/drm/drm_edid.c +2
-0+static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)That names seems off. Should probably be
drm_parse_hdmi_forum_vsdb()or something.
Actually, unlike the last patch set, we are not parsing the whole hf_vsdb, but parsing it only for scrambling status byte (hf_vsdb[5]). But may be I can make it drm_detect_scrambling_from_hfvsdb ot something similar. We will have more hf_vsdb parsing for 3d flags, yuv420_deep_color etc.
Quoted 11 lines
Quoted 11 lines
drivers/gpu/drm/drm_edid.c +11
-0+{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M. +* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out.
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3836
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +6
-0+*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ; +DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock);I wonder if we should be a little paranoid and ignore this if it's <=340?
Sure, will do it.
Quoted 17 lines
Quoted 17 lines
drivers/gpu/drm/drm_edid.c +16
-0+ +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true; + } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel +* +* Read the scrambler status over SCDC channel, and check the
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3858
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +6
-0+* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. +*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter)The name is again a little wonky. And it looks like something that should live alognside the SCDC helper stuff.
Yep, Thierry also suggested the same, to move it along with SCDC. Will do it.
Quoted 11 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3868
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) { +DRM_ERROR ("Failed to read scrambling status\n" ); +return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ;return status &
SCDC_SCRAMBLING_STATUS
Sure.
Quoted 16 lines
Quoted 16 lines
drivers/gpu/drm/drm_edid.c +16
-0+} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling +* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config;
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3890
Quoted 6 lines
drivers/gpu/drm/drm_edid.c +6
-0+struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + }I don't think we want to track any dynamic state in the display info. That belongs to the atomic state stuff.
Hummm, ok.
Quoted 3 lines
And the function again looks like something that belongs in the SCDC helper.
Agree.
Quoted 4 lines
Since the two pieces of infromaton in this registrer are the scramble control and the clock ratio, I think we might want to just have one function to configure both.
That's a good suggestion, thanks.
- Shashank
Quoted 120 lines
Quoted 120 lines
drivers/gpu/drm/drm_edid.c +56
-1+ +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +24
-0@@ -90,6 +90,26 @@ enum subpixel_order { }; + +/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. +*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks; +/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink * @@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. */ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info; };/** include/drm/drm_edid.h +0
-1@@ -462,5 +462,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,struct drm_display_mode *drm_mode_find_dmt (struct drm_device *dev,int hsize,int vsize,int fresh,bool rb); -
Quoted 8 lines
Quoted 8 lines
include/drm/drm_edid.h +5
-0+bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_check_scrambling_status (struct i2c_adapter *adapter);#endif /* __DRM_EDID_H__ */ Signature · 1 line
1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/6] drm: scrambling support in drm layer
Quoted 44 lines · Shashank
Regards
Shashank
Quoted 34 lines · Ville Syrjälä
Quoted 33 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } }Quoted 4 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3819
Quoted 2 lines
drivers/gpu/drm/drm_edid.c +2
-0+static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)That names seems off. Should probably be
drm_parse_hdmi_forum_vsdb()or something.
Quoted 6 lines
Actually, unlike the last patch set, we are not parsing the whole
hf_vsdb, but parsing it only for
scrambling status byte (hf_vsdb[5]). But may be I can make itdrm_detect_scrambling_from_hfvsdb
ot something similar. We will have morehf_vsdbparsing for 3d flags,yuv420_deep_coloretc.
Well, so far I'm not seeing much point in splitting it up. So I'd stuff it all into one place, for now at least.
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/6] drm: scrambling support in drm layer
Regards
Shashank
Quoted 45 lines · Ville Syrjälä
Quoted 44 lines · Shashank
Regards
Shashank
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3819
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +2
-0@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)That names seems off. Should probably be
drm_parse_hdmi_forum_vsdb()or something.
Quoted 8 lines
Quoted 6 lines
Actually, unlike the last patch set, we are not parsing the whole
hf_vsdb, but parsing it only for
scrambling status byte (hf_vsdb[5]). But may be I can make itdrm_detect_scrambling_from_hfvsdb
ot something similar. We will have morehf_vsdbparsing for 3d flags,yuv420_deep_coloretc.Well, so far I'm not seeing much point in splitting it up. So I'd stuff it all into one place, for now at least.
I had published a patch just doing as you suggested which was parsing complete hf-vsdb in one shot, and adding info in hdmi_info structure, to accommodate it.
(Patch https://patchwork.freedesktop.org/patch/128963/ and https://patchwork.freedesktop.org/patch/128962/)
But you gave a review comment not to add anything which is not being used in the patch series:
https://patchwork.freedesktop.org/patch/128962/
That was the only reason I have split hf-vsdb parsing patch into 3 parts
- parse SCDC and scrambling info (here)
- with YUV420 deep color ( upcoming )
- with 3d handling (upcoming)
So I am confused, split or no split :-) ?
- Shashank
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/6] drm: scrambling support in drm layer
Quoted 65 lines · Shashank
Regards
Shashank
Quoted 45 lines · Ville Syrjälä
Quoted 44 lines · Shashank
Regards
Shashank
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3819
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +2
-0@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)That names seems off. Should probably be
drm_parse_hdmi_forum_vsdb()or something.Quoted 8 lines
Quoted 6 lines
Actually, unlike the last patch set, we are not parsing the whole
hf_vsdb, but parsing it only for
scrambling status byte (hf_vsdb[5]). But may be I can make itdrm_detect_scrambling_from_hfvsdb
ot something similar. We will have morehf_vsdbparsing for 3d flags,yuv420_deep_coloretc.Well, so far I'm not seeing much point in splitting it up. So I'd stuff it all into one place, for now at least.
I had published a patch just doing as you suggested which was parsing complete hf-vsdb in one shot, and adding info in
hdmi_infostructure, to accommodate it.
(Patch https://patchwork.freedesktop.org/patch/128963/ and
https://patchwork.freedesktop.org/patch/128962/)
Quoted 3 lines
But you gave a review comment not to add anything which is not being used in the patch series:
https://patchwork.freedesktop.org/patch/128962/
That's doesn't require the things that are left to be split into separate functions.
Quoted 9 lines
That was the only reason I have split hf-vsdb parsing patch into 3 parts
- parse SCDC and scrambling info (here)
- with YUV420 deep color ( upcoming )
- with 3d handling (upcoming)So I am confused, split or no split :-) ?
- Shashank
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/6] drm: scrambling support in drm layer
Regards
Shashank
Quoted 66 lines · Ville Syrjälä
Quoted 65 lines · Shashank
Regards
Shashank
Quoted 45 lines · Ville Syrjälä
Quoted 44 lines · Shashank
Regards
Shashank
Quoted 38 lines · Ville Syrjälä
Quoted 30 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +1
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3819
Quoted 5 lines
drivers/gpu/drm/drm_edid.c +2
-0@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb)That names seems off. Should probably be
drm_parse_hdmi_forum_vsdb()or something.Quoted 8 lines
Quoted 6 lines
Actually, unlike the last patch set, we are not parsing the whole
hf_vsdb, but parsing it only for
scrambling status byte (hf_vsdb[5]). But may be I can make itdrm_detect_scrambling_from_hfvsdb
ot something similar. We will have morehf_vsdbparsing for 3d flags,yuv420_deep_coloretc.Well, so far I'm not seeing much point in splitting it up. So I'd stuff it all into one place, for now at least.
I had published a patch just doing as you suggested which was parsing complete hf-vsdb in one shot, and adding info in
hdmi_infostructure, to accommodate it.
(Patch https://patchwork.freedesktop.org/patch/128963/ and
https://patchwork.freedesktop.org/patch/128962/)
Quoted 5 lines
Quoted 3 lines
But you gave a review comment not to add anything which is not being used in the patch series:
https://patchwork.freedesktop.org/patch/128962/That's doesn't require the things that are left to be split into separate functions.
So please let me know if my understanding is correct.
- Name the function as *_parse_hfvsdb only
- Call it while parsing the EDID extension blocks (the same place)
- Keep on adding parsing of the HF-VSDB blocks, in the same function, in an incremental way, as we add patches for them. In this way the function won't be split into multiple small functions, but all the parsing will be done in one function.
- Shashank
Quoted 8 lines
Quoted 8 lines
That was the only reason I have split hf-vsdb parsing patch into 3 parts
- parse SCDC and scrambling info (here)
- with YUV420 deep color ( upcoming )
- with 3d handling (upcoming)So I am confused, split or no split :-) ?
- Shashank
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 4/6] drm: scrambling support in drm layer
In reply to Shashank SharmaQuoted 40 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +8
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/*
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3834
Quoted 10 lines
drivers/gpu/drm/drm_edid.c +10
-0+* All HDMI 2.0 monitors must support scrambling at rates > 340M. +* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check) +* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ;
Comment explaining or quoting where the 5000 comes from?
Quoted 135 lines
drivers/gpu/drm/drm_edid.c +112
-1+DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock); + +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true; + } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel +* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. +*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter) +{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) { +DRM_ERROR ("Failed to read scrambling status\n" ); +return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ; +} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling +* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +3
-0@@ -90,6 +90,26 @@ enum subpixel_order { }; + +/** +* struct scrambling: sink's scrambling support.
include/drm/drm_connector.h enum subpixel_order { · line 105
Quoted 10 lines
include/drm/drm_connector.h +10
-0+*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. +*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks;
The naming for low and high clock rates looks asymmetric.
Quoted 26 lines
include/drm/drm_connector.h +11
-0+/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink * @@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. */ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info; };/** include/drm/drm_edid.h +0
-0
include/drm/drm_edid.h void drm_edid_get_monitor_name(struct edid *edid, char *name, · line 470
Quoted 10 lines
include/drm/drm_edid.h +5
-1@@ -462,5 +462,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,struct drm_display_mode *drm_mode_find_dmt (struct drm_device *dev,int hsize,int vsize,int fresh,bool rb); - +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_check_scrambling_status (struct i2c_adapter *adapter);#endif /* __DRM_EDID_H__ */
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [Intel-gfx] [PATCH 4/6] drm: scrambling support in drm layer
Thanks for the review, Dhinakaran.
Regards
Shashank
Quoted 44 lines · Dhinakaran
Quoted 43 lines · Shashank Sharma
HDMI 2.0 spec mandates scrambling for modes with pixel clock higher than 340Mhz. This patch adds few new functions in drm layer for core drivers to enable/disable scrambling.
This patch adds:
- A function to detect scrambling support parsing HF-VSDB
- A function to check scrambling status runtime using SCDC read.
- Two functions to enable/disable scrambling using SCDC read/write.
- Few new bools to reflect scrambling support and status.Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/drm_edid.c | 131 +++++++++++++++++++++++++++++++++++++++++++- include/drm/drm_connector.h | 24 ++++++++ include/drm/drm_edid.h | 6 +- 3 files changed, 159 insertions(+), 2 deletions(-)drivers/gpu/drm/drm_edid.c +11
-0@@ -37,6 +37,7 @@#include <drm/drm_edid.h> #include <drm/drm_encoder.h> #include <drm/drm_displayid.h> +#include <drm/drm_scdc_helper.h> #define version_greater (edid, maj, min) \ (((edid)->version > (maj)) || \@@ -3814,6 +3815,132 @@ static void drm_detect_hdmi_scdc(struct drm_connector *connector, } } +static void drm_detect_hdmi_scrambling (struct drm_connector *connector, +const u8 *hf_vsdb) +{ +struct drm_display_info *display = &connector->display_info; +struct drm_hdmi_info *hdmi = &display->hdmi_info; + +/* +* All HDMI 2.0 monitors must support scrambling at rates > 340M. +* And as per the spec, three factors confirm this: +* * Availability of a HF-VSDB block in EDID (check)
Quoted 8 lines
drivers/gpu/drm/drm_edid.c static void drm_detect_hdmi_scdc(struct drm_connector *connector, · line 3834
Quoted 7 lines
drivers/gpu/drm/drm_edid.c +7
-0+* * Non zero Max_TMDS_Char_Rate filed in HF-VSDB +* * SCDC support available +* Lets check it out. +*/ + +if (hf_vsdb[5 ]) { + display->max_tmds_clock = hf_vsdb[5 ] *5000 ;Comment explaining or quoting where the 5000 comes from?
Sure, can be done.
Quoted 133 lines
Quoted 133 lines
drivers/gpu/drm/drm_edid.c +112
-1+DRM_DEBUG_KMS ("HF-VSDB: max TMDS clock %d kHz\n" , + display->max_tmds_clock); + +if (hdmi->scdc_supported) { + hdmi->scr_info.supported = true; + +/* Few sinks support scrambling for cloks < 340M */ +if ((hf_vsdb[6 ] &0x8 )) + hdmi->scr_info.low_clocks = true; + } + } +} + +/** +* drm_check_scrambling_status - what is status of scrambling? +* @adapter: i2c adapter for SCDC channel +* +* Read the scrambler status over SCDC channel, and check the +* scrambling status. +* +* Return: True if the scrambling is enabled, false otherwise. +*/ + +bool drm_check_scrambling_status (struct i2c_adapter *adapter) +{ +u8 status; + +if (drm_scdc_readb (adapter,SCDC_SCRAMBLER_STATUS , &status) <0 ) { +DRM_ERROR ("Failed to read scrambling status\n" ); +return false; + } + + status &=SCDC_SCRAMBLING_STATUS ; +return status !=0 ; +} + +/** +* drm_enable_scrambling - enable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: enable scrambling, even if its already enabled +* +* Write the TMDS config over SCDC channel, and enable scrambling +* Return: True if scrambling is successfully enabled, false otherwise. +*/ + +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already enabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config |=SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return hdmi_info->scr_info.status; +} + +/** +* drm_disable_scrambling - disable scrambling +* @connector: target drm_connector +* @adapter: i2c adapter for SCDC channel +* @force: disable scrambling, even if its already disabled +* +* Write the TMDS config over SCDC channel, and disable scrambling +* Return: True if scrambling is successfully disabled, false otherwise. +*/ +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force) +{ +u8 config; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; + +if (!hdmi_info->scr_info.status && !force) { +DRM_DEBUG_KMS ("Scrambling already disabled\n" ); +return true; + } + +if (drm_scdc_readb (adapter,SCDC_TMDS_CONFIG , &config) <0 ) { +DRM_ERROR ("Failed to read tmds config\n" ); +return false; + } + + config &= ~SCDC_SCRAMBLING_ENABLE ; + +if (drm_scdc_writeb (adapter,SCDC_TMDS_CONFIG , config) <0 ) { +DRM_ERROR ("Failed to enable scrambling, write error\n" ); +return false; + } + + hdmi_info->scr_info.status =drm_check_scrambling_status (adapter); +return !hdmi_info->scr_info.status; +} +static void drm_parse_hdmi_deep_color_info (struct drm_connector *connector,const u8 *hdmi) {@@ -3928,8 +4055,10 @@ static void drm_parse_cea_ext(struct drm_connector *connector,if (cea_db_is_hdmi_vsdb (db))drm_parse_hdmi_vsdb_video (connector, db); -if (cea_db_is_hdmi_forum_vsdb (db)) +if (cea_db_is_hdmi_forum_vsdb (db)) {drm_detect_hdmi_scdc (connector, db); +drm_detect_hdmi_scrambling (connector, db); + } } }include/drm/drm_connector.h +0
-0@@ -90,6 +90,26 @@ enum subpixel_order { };
Quoted 14 lines
include/drm/drm_connector.h enum subpixel_order { · line 105
Quoted 13 lines
include/drm/drm_connector.h +13
-0+ +/** +* struct scrambling: sink's scrambling support. +*/ +struct scrambling { +/** +* @supported: scrambling supported for rates > 340Mhz. +*/ +bool supported; +/** +* @low_clocks: scrambling supported for rates <= 340Mhz. +*/ +bool low_clocks;The naming for low and high clock rates looks asymmetric.
I dont get it, I dont have a high clock here, can you please elaborate ?
- Shashank
Quoted 20 lines
Quoted 20 lines
include/drm/drm_connector.h +11
-0+/** +* @status: scrambling enabled/disabled ? +*/ +bool status; +}; + +/** * struct drm_hdmi_info - runtime data about the connected sink * @@ -108,6 +128,10 @@ struct drm_hdmi_info {* @scdc_rr: sink is capable of generating scdc read request. */ bool scdc_rr; +/** +* scr_info: sink's scrambling support and capabilities. +*/ +struct scrambling scr_info; };
Quoted 16 lines
Quoted 6 lines
include/drm/drm_connector.h +0
-0/** include/drm/drm_edid.h +0
-0include/drm/drm_edid.h void drm_edid_get_monitor_name(struct edid *edid, char *name, · line 470
Quoted 10 lines
include/drm/drm_edid.h +5
-1@@ -462,5 +462,9 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,struct drm_display_mode *drm_mode_find_dmt (struct drm_device *dev,int hsize,int vsize,int fresh,bool rb); - +bool drm_enable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_disable_scrambling (struct drm_connector *connector, +struct i2c_adapter *adapter,bool force); +bool drm_check_scrambling_status (struct i2c_adapter *adapter);#endif /* __DRM_EDID_H__ */
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH 5/6 drm/i915: enable scrambling
In reply to Shashank SharmaGeminilake platform has a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.
--- drivers/gpu/drm/i915/i915_reg.h | 2 ++ drivers/gpu/drm/i915/intel_ddi.c | 5 +++++ drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_hdmi.c | 42 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 51 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +2 -0
@@ -7807,6 +7807,8 @@ enum {#define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12)#define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8)#define TRANS_DDI_BFI_ENABLE (1<<4) +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0)/* DisplayPort Transport Control */ #define _DP_TP_CTL_A 0x64040
drivers/gpu/drm/i915/intel_ddi.c +5 -0
@@ -1278,6 +1278,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) temp |=TRANS_DDI_MODE_SELECT_HDMI ; else temp |= TRANS_DDI_MODE_SELECT_DVI; + +if (IS_GEMINILAKE (dev_priv)) { + temp |=intel_hdmi_check_scrambling (intel_encoder, + &intel_crtc->config->base.adjusted_mode); + } }else if (type ==INTEL_OUTPUT_ANALOG ) { temp |=TRANS_DDI_MODE_SELECT_FDI ; temp |= (intel_crtc->config->fdi_lanes -1 ) <<1 ;
drivers/gpu/drm/i915/intel_drv.h +2 -0
@@ -1588,6 +1588,8 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,bool intel_hdmi_compute_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config,struct drm_connector_state *conn_state); +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode);void intel_dp_dual_mode_set_tmds_output (struct intel_hdmi *hdmi,bool enable);
drivers/gpu/drm/i915/intel_hdmi.c +42 -0
48 lines not on this page · raw message
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/6] drm/i915: enable scrambling
Quoted 66 lines · Shashank Sharma
Geminilake platform has a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 2 ++ drivers/gpu/drm/i915/intel_ddi.c | 5 +++++ drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_hdmi.c | 42 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 51 insertions(+)drivers/gpu/drm/i915/i915_reg.h +2
-0@@ -7807,6 +7807,8 @@ enum {#define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12)#define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8)#define TRANS_DDI_BFI_ENABLE (1<<4) +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0)/* DisplayPort Transport Control */ #define _DP_TP_CTL_A 0x64040drivers/gpu/drm/i915/intel_ddi.c +5
-0@@ -1278,6 +1278,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) temp |=TRANS_DDI_MODE_SELECT_HDMI ; else temp |= TRANS_DDI_MODE_SELECT_DVI; + +if (IS_GEMINILAKE (dev_priv)) { + temp |=intel_hdmi_check_scrambling (intel_encoder, + &intel_crtc->config->base.adjusted_mode); + } }else if (type ==INTEL_OUTPUT_ANALOG ) { temp |=TRANS_DDI_MODE_SELECT_FDI ; temp |= (intel_crtc->config->fdi_lanes -1 ) <<1 ;drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -1588,6 +1588,8 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,bool intel_hdmi_compute_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config,struct drm_connector_state *conn_state); +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode);void intel_dp_dual_mode_set_tmds_output (struct intel_hdmi *hdmi,bool enable);drivers/gpu/drm/i915/intel_hdmi.c +1
-0@@ -1795,6 +1795,48 @@ static void intel_hdmi_destroy(struct drm_connector *connector) intel_hdmi->aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; } +static void
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1808
Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +10
-0+intel_hdmi_enable_scrambling(struct drm_connector *connector) +{ +struct drm_i915_private *dev_priv = connector->dev->dev_private; +struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector); +struct i2c_adapter *adapter = +intel_gmbus_get_adapter (dev_priv, intel_hdmi->ddc_bus); + +if (!drm_enable_scrambling (connector, adapter, true)) +DRM_ERROR ("Request to enable scrambling failed\n" ); +}
I don't like hiding this somewhere deep like this. It should be somewhere much higher up.
And I'm thinkign we might want to track the scrambler state in the crtc state.
Quoted 36 lines
drivers/gpu/drm/i915/intel_hdmi.c +31
-0+ +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode) +{ +struct intel_hdmi *intel_hdmi =enc_to_intel_hdmi (&intel_encoder->base); +struct drm_connector *connector = &intel_hdmi->attached_connector->base; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +uint32_t hdmi_config =0 ; + +DRM_DEBUG_KMS ("Checking scrambling for enc:%s connector:%s\n" , + intel_encoder->base.name, connector->name); + +if (mode->clock <340000 ) { +if (hdmi_info->scr_info.low_clocks) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } +return hdmi_config; + } + +/* Enable scrambling for clocks > 340M */ +if (hdmi_info->scr_info.supported) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } + +/* Scrambling or not, if clock > 340M, set high char rate */ + hdmi_config |=TRANS_DDI_HIGH_TMDS_CHAR_RATE ; +return hdmi_config; +} +static u8 intel_hdmi_ddc_pin (struct drm_i915_private *dev_priv,enum port port) {Signature · 1 line
1.9.1
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/6] drm/i915: enable scrambling
Regards
Shashank
Quoted 66 lines · Ville Syrjälä
Quoted 65 lines · Shashank Sharma
Geminilake platform has a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 2 ++ drivers/gpu/drm/i915/intel_ddi.c | 5 +++++ drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_hdmi.c | 42 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 51 insertions(+)drivers/gpu/drm/i915/i915_reg.h +2
-0@@ -7807,6 +7807,8 @@ enum {#define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12)#define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8)#define TRANS_DDI_BFI_ENABLE (1<<4) +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0)/* DisplayPort Transport Control */ #define _DP_TP_CTL_A 0x64040drivers/gpu/drm/i915/intel_ddi.c +5
-0@@ -1278,6 +1278,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) temp |=TRANS_DDI_MODE_SELECT_HDMI ; else temp |= TRANS_DDI_MODE_SELECT_DVI; + +if (IS_GEMINILAKE (dev_priv)) { + temp |=intel_hdmi_check_scrambling (intel_encoder, + &intel_crtc->config->base.adjusted_mode); + } }else if (type ==INTEL_OUTPUT_ANALOG ) { temp |=TRANS_DDI_MODE_SELECT_FDI ; temp |= (intel_crtc->config->fdi_lanes -1 ) <<1 ;drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -1588,6 +1588,8 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,bool intel_hdmi_compute_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config,struct drm_connector_state *conn_state); +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode);void intel_dp_dual_mode_set_tmds_output (struct intel_hdmi *hdmi,bool enable);drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -1795,6 +1795,48 @@ static void intel_hdmi_destroy(struct drm_connector *connector) intel_hdmi->aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; }
Quoted 13 lines
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1808
Quoted 11 lines
drivers/gpu/drm/i915/intel_hdmi.c +11
-0+static void +intel_hdmi_enable_scrambling (struct drm_connector *connector) +{ +struct drm_i915_private *dev_priv = connector->dev->dev_private; +struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector); +struct i2c_adapter *adapter = +intel_gmbus_get_adapter (dev_priv, intel_hdmi->ddc_bus); + +if (!drm_enable_scrambling (connector, adapter, true)) +DRM_ERROR ("Request to enable scrambling failed\n" ); +}I don't like hiding this somewhere deep like this. It should be somewhere much higher up.
Why ? All we need to do here is enable two bits in transcoder control register, which is already being programmed in a calling function, so I dont see the use case, but I might be missing some bigger picture. Can you please elaborate on this ?
Quoted 3 lines
And I'm thinkign we might want to track the scrambler state in the crtc state.
Yes, that's a pretty good way to track dynamic status of scrambler, do you think we should add this in drm_crtc_state itself ?
- Shashank
Quoted 28 lines
Quoted 28 lines
drivers/gpu/drm/i915/intel_hdmi.c +28
-0+ +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode) +{ +struct intel_hdmi *intel_hdmi =enc_to_intel_hdmi (&intel_encoder->base); +struct drm_connector *connector = &intel_hdmi->attached_connector->base; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +uint32_t hdmi_config =0 ; + +DRM_DEBUG_KMS ("Checking scrambling for enc:%s connector:%s\n" , + intel_encoder->base.name, connector->name); + +if (mode->clock <340000 ) { +if (hdmi_info->scr_info.low_clocks) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } +return hdmi_config; + } + +/* Enable scrambling for clocks > 340M */ +if (hdmi_info->scr_info.supported) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } + +/* Scrambling or not, if clock > 340M, set high char rate */ + hdmi_config |=TRANS_DDI_HIGH_TMDS_CHAR_RATE ;
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0+return hdmi_config; +} +static u8 intel_hdmi_ddc_pin (struct drm_i915_private *dev_priv,enum port port) {Signature · 1 line
1.9.1
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 5/6] drm/i915: enable scrambling
Quoted 85 lines · Shashank
Regards
Shashank
Quoted 66 lines · Ville Syrjälä
Quoted 65 lines · Shashank Sharma
Geminilake platform has a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 2 ++ drivers/gpu/drm/i915/intel_ddi.c | 5 +++++ drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_hdmi.c | 42 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 51 insertions(+)drivers/gpu/drm/i915/i915_reg.h +2
-0@@ -7807,6 +7807,8 @@ enum {#define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12)#define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8)#define TRANS_DDI_BFI_ENABLE (1<<4) +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0)/* DisplayPort Transport Control */ #define _DP_TP_CTL_A 0x64040drivers/gpu/drm/i915/intel_ddi.c +5
-0@@ -1278,6 +1278,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) temp |=TRANS_DDI_MODE_SELECT_HDMI ; else temp |= TRANS_DDI_MODE_SELECT_DVI; + +if (IS_GEMINILAKE (dev_priv)) { + temp |=intel_hdmi_check_scrambling (intel_encoder, + &intel_crtc->config->base.adjusted_mode); + } }else if (type ==INTEL_OUTPUT_ANALOG ) { temp |=TRANS_DDI_MODE_SELECT_FDI ; temp |= (intel_crtc->config->fdi_lanes -1 ) <<1 ;drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -1588,6 +1588,8 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,bool intel_hdmi_compute_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config,struct drm_connector_state *conn_state); +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode);void intel_dp_dual_mode_set_tmds_output (struct intel_hdmi *hdmi,bool enable);drivers/gpu/drm/i915/intel_hdmi.c +0
-0@@ -1795,6 +1795,48 @@ static void intel_hdmi_destroy(struct drm_connector *connector) intel_hdmi->aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; }Quoted 13 lines
drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1808
Quoted 11 lines
drivers/gpu/drm/i915/intel_hdmi.c +11
-0+static void +intel_hdmi_enable_scrambling (struct drm_connector *connector) +{ +struct drm_i915_private *dev_priv = connector->dev->dev_private; +struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector); +struct i2c_adapter *adapter = +intel_gmbus_get_adapter (dev_priv, intel_hdmi->ddc_bus); + +if (!drm_enable_scrambling (connector, adapter, true)) +DRM_ERROR ("Request to enable scrambling failed\n" ); +}I don't like hiding this somewhere deep like this. It should be somewhere much higher up.
Quoted 5 lines
Why ? All we need to do here is enable two bits in transcoder control register, which is already being
programmed in a calling function, so I dont see the use case, but I might be missing some bigger picture.
Can you please elaborate on this ?
We're talking to the display here, which is rather surprising to happen from a function thing that on the first glance doesn't even seem to touch the hardware.
Quoted 6 lines
Quoted 3 lines
And I'm thinkign we might want to track the scrambler state in the crtc state.
Yes, that's a pretty good way to track dynamic status of scrambler, do you think we should add this in
drm_crtc_stateitself ?
I'd just start with intel specific state and later we can see what everyone else wants to do and potentially unify a bit.
Quoted 38 lines
- Shashank
Quoted 36 lines
Quoted 36 lines
drivers/gpu/drm/i915/intel_hdmi.c +31
-0+ +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode) +{ +struct intel_hdmi *intel_hdmi =enc_to_intel_hdmi (&intel_encoder->base); +struct drm_connector *connector = &intel_hdmi->attached_connector->base; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +uint32_t hdmi_config =0 ; + +DRM_DEBUG_KMS ("Checking scrambling for enc:%s connector:%s\n" , + intel_encoder->base.name, connector->name); + +if (mode->clock <340000 ) { +if (hdmi_info->scr_info.low_clocks) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } +return hdmi_config; + } + +/* Enable scrambling for clocks > 340M */ +if (hdmi_info->scr_info.supported) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } + +/* Scrambling or not, if clock > 340M, set high char rate */ + hdmi_config |=TRANS_DDI_HIGH_TMDS_CHAR_RATE ; +return hdmi_config; +} +static u8 intel_hdmi_ddc_pin (struct drm_i915_private *dev_priv,enum port port) {Signature · 1 line
1.9.1
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 5/6] drm/i915: enable scrambling
Regards
Shashank
Quoted 86 lines · Ville Syrjälä
Quoted 85 lines · Shashank
Regards
Shashank
Quoted 79 lines · Ville Syrjälä
Quoted 66 lines · Shashank Sharma
Geminilake platform has a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 2 ++ drivers/gpu/drm/i915/intel_ddi.c | 5 +++++ drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_hdmi.c | 42 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 51 insertions(+)drivers/gpu/drm/i915/i915_reg.h +2
-0@@ -7807,6 +7807,8 @@ enum {#define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12)#define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8)#define TRANS_DDI_BFI_ENABLE (1<<4) +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0)/* DisplayPort Transport Control */ #define _DP_TP_CTL_A 0x64040drivers/gpu/drm/i915/intel_ddi.c +5
-0@@ -1278,6 +1278,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) temp |=TRANS_DDI_MODE_SELECT_HDMI ; else temp |= TRANS_DDI_MODE_SELECT_DVI; + +if (IS_GEMINILAKE (dev_priv)) { + temp |=intel_hdmi_check_scrambling (intel_encoder, + &intel_crtc->config->base.adjusted_mode); + } }else if (type ==INTEL_OUTPUT_ANALOG ) { temp |=TRANS_DDI_MODE_SELECT_FDI ; temp |= (intel_crtc->config->fdi_lanes -1 ) <<1 ;drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -1588,6 +1588,8 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,bool intel_hdmi_compute_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config,struct drm_connector_state *conn_state); +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode);void intel_dp_dual_mode_set_tmds_output (struct intel_hdmi *hdmi,bool enable);drivers/gpu/drm/i915/intel_hdmi.c +1
-0@@ -1795,6 +1795,48 @@ static void intel_hdmi_destroy(struct drm_connector *connector) intel_hdmi->aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; } +static voiddrivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1808
Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +10
-0+intel_hdmi_enable_scrambling(struct drm_connector *connector) +{ +struct drm_i915_private *dev_priv = connector->dev->dev_private; +struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector); +struct i2c_adapter *adapter = +intel_gmbus_get_adapter (dev_priv, intel_hdmi->ddc_bus); + +if (!drm_enable_scrambling (connector, adapter, true)) +DRM_ERROR ("Request to enable scrambling failed\n" ); +}I don't like hiding this somewhere deep like this. It should be somewhere much higher up.
Quoted 8 lines
Quoted 5 lines
Why ? All we need to do here is enable two bits in transcoder control register, which is already being
programmed in a calling function, so I dont see the use case, but I might be missing some bigger picture.
Can you please elaborate on this ?We're talking to the display here, which is rather surprising to happen from a function thing that on the first glance doesn't even seem to touch the hardware.
I kind of agree with this, and I am also tempted now to shift this call upwards, but I want to keep this close to port enabling as well, as the HDMI 2.0 spec says:
"Max time period between a source enables scrambling on monitor, and starts sending scrambled
video should be 100ms" else the sink might choose to disable scrambling.
Considering this, where do you think would be right place to enabled scrambling on monitor ?
- Shashank
Quoted 37 lines
Quoted 5 lines
Quoted 2 lines
And I'm thinkign we might want to track the scrambler state in the crtc state.
Yes, that's a pretty good way to track dynamic status of scrambler, do you think we should add this in
drm_crtc_stateitself ?I'd just start with intel specific state and later we can see what everyone else wants to do and potentially unify a bit.
Quoted 29 lines
- Shashank
Quoted 28 lines
Quoted 28 lines
drivers/gpu/drm/i915/intel_hdmi.c +28
-0+ +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode) +{ +struct intel_hdmi *intel_hdmi =enc_to_intel_hdmi (&intel_encoder->base); +struct drm_connector *connector = &intel_hdmi->attached_connector->base; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +uint32_t hdmi_config =0 ; + +DRM_DEBUG_KMS ("Checking scrambling for enc:%s connector:%s\n" , + intel_encoder->base.name, connector->name); + +if (mode->clock <340000 ) { +if (hdmi_info->scr_info.low_clocks) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } +return hdmi_config; + } + +/* Enable scrambling for clocks > 340M */ +if (hdmi_info->scr_info.supported) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } + +/* Scrambling or not, if clock > 340M, set high char rate */ + hdmi_config |=TRANS_DDI_HIGH_TMDS_CHAR_RATE ;
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_hdmi.c +3
-0+return hdmi_config; +} +static u8 intel_hdmi_ddc_pin (struct drm_i915_private *dev_priv,enum port port) {Signature · 1 line
1.9.1
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH 5/6] drm/i915: enable scrambling
Quoted 107 lines · Shashank
Regards
Shashank
Quoted 86 lines · Ville Syrjälä
Quoted 85 lines · Shashank
Regards
Shashank
Quoted 79 lines · Ville Syrjälä
Quoted 66 lines · Shashank Sharma
Geminilake platform has a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.
Signed-off-by Shashank Sharma <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 2 ++ drivers/gpu/drm/i915/intel_ddi.c | 5 +++++ drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_hdmi.c | 42 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 51 insertions(+)drivers/gpu/drm/i915/i915_reg.h +2
-0@@ -7807,6 +7807,8 @@ enum {#define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12)#define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8)#define TRANS_DDI_BFI_ENABLE (1<<4) +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0)/* DisplayPort Transport Control */ #define _DP_TP_CTL_A 0x64040drivers/gpu/drm/i915/intel_ddi.c +5
-0@@ -1278,6 +1278,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) temp |=TRANS_DDI_MODE_SELECT_HDMI ; else temp |= TRANS_DDI_MODE_SELECT_DVI; + +if (IS_GEMINILAKE (dev_priv)) { + temp |=intel_hdmi_check_scrambling (intel_encoder, + &intel_crtc->config->base.adjusted_mode); + } }else if (type ==INTEL_OUTPUT_ANALOG ) { temp |=TRANS_DDI_MODE_SELECT_FDI ; temp |= (intel_crtc->config->fdi_lanes -1 ) <<1 ;drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -1588,6 +1588,8 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,bool intel_hdmi_compute_config (struct intel_encoder *encoder,struct intel_crtc_state *pipe_config,struct drm_connector_state *conn_state); +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode);void intel_dp_dual_mode_set_tmds_output (struct intel_hdmi *hdmi,bool enable);drivers/gpu/drm/i915/intel_hdmi.c +1
-0@@ -1795,6 +1795,48 @@ static void intel_hdmi_destroy(struct drm_connector *connector) intel_hdmi->aspect_ratio =HDMI_PICTURE_ASPECT_NONE ; } +static voiddrivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1808
Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +10
-0+intel_hdmi_enable_scrambling(struct drm_connector *connector) +{ +struct drm_i915_private *dev_priv = connector->dev->dev_private; +struct intel_hdmi *intel_hdmi =intel_attached_hdmi (connector); +struct i2c_adapter *adapter = +intel_gmbus_get_adapter (dev_priv, intel_hdmi->ddc_bus); + +if (!drm_enable_scrambling (connector, adapter, true)) +DRM_ERROR ("Request to enable scrambling failed\n" ); +}I don't like hiding this somewhere deep like this. It should be somewhere much higher up.
Quoted 8 lines
Quoted 5 lines
Why ? All we need to do here is enable two bits in transcoder control register, which is already being
programmed in a calling function, so I dont see the use case, but I might be missing some bigger picture.
Can you please elaborate on this ?We're talking to the display here, which is rather surprising to happen from a function thing that on the first glance doesn't even seem to touch the hardware.
I kind of agree with this, and I am also tempted now to shift this call upwards, but I want to
keep this close to port enabling as well, as the HDMI 2.0 spec says:
"Max time period between a source enables scrambling on monitor, and starts sending scrambled
video should be 100ms" else the sink might choose to disable scrambling.
Quoted 2 lines
Considering this, where do you think would be right place to enabled scrambling on monitor ?
intel_enable_ddi() is where we presumbly enable the port, so maybe there.
Quoted 47 lines
- Shashank
Quoted 45 lines
Quoted 5 lines
Quoted 2 lines
And I'm thinkign we might want to track the scrambler state in the crtc state.
Yes, that's a pretty good way to track dynamic status of scrambler, do you think we should add this in
drm_crtc_stateitself ?I'd just start with intel specific state and later we can see what everyone else wants to do and potentially unify a bit.
Quoted 37 lines
- Shashank
Quoted 36 lines
Quoted 36 lines
drivers/gpu/drm/i915/intel_hdmi.c +31
-0+ +uint32_t intel_hdmi_check_scrambling (struct intel_encoder *intel_encoder, +struct drm_display_mode *mode) +{ +struct intel_hdmi *intel_hdmi =enc_to_intel_hdmi (&intel_encoder->base); +struct drm_connector *connector = &intel_hdmi->attached_connector->base; +struct drm_hdmi_info *hdmi_info = &connector->display_info.hdmi_info; +uint32_t hdmi_config =0 ; + +DRM_DEBUG_KMS ("Checking scrambling for enc:%s connector:%s\n" , + intel_encoder->base.name, connector->name); + +if (mode->clock <340000 ) { +if (hdmi_info->scr_info.low_clocks) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } +return hdmi_config; + } + +/* Enable scrambling for clocks > 340M */ +if (hdmi_info->scr_info.supported) { +intel_hdmi_enable_scrambling (connector); + hdmi_config |=TRANS_DDI_HDMI_SCRAMBLING ; + } + +/* Scrambling or not, if clock > 340M, set high char rate */ + hdmi_config |=TRANS_DDI_HIGH_TMDS_CHAR_RATE ; +return hdmi_config; +} +static u8 intel_hdmi_ddc_pin (struct drm_i915_private *dev_priv,enum port port) {Signature · 1 line
1.9.1
Signature · 6 lines
Ville Syrjälä Intel OTC _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
PATCH 6/6 drm/i915: allow HDMI 2.0 clock rates
In reply to Shashank SharmaGeminilake has a native HDMI 2.0 controller, which is capable of driving clocks upto 594Mhz. This patch updates the max tmds clock limit for the same.
--- drivers/gpu/drm/i915/intel_hdmi.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/gpu/drm/i915/intel_hdmi.c +2 -0
@@ -1209,6 +1209,8 @@ static int intel_hdmi_source_max_tmds_clock(struct drm_i915_private *dev_priv) {if (IS_G4X (dev_priv))return 165000 ; +else if (IS_GEMINILAKE (dev_priv)) +return 594000 ;else if (IS_HASWELL (dev_priv) ||INTEL_INFO (dev_priv)->gen >=8 )return 300000 ;else
Signature · 6 lines
1.9.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.BAT: failure for HDMI 2.0: Scrambling support in DRM layer
In reply to Shashank Sharma== Series Details ==
== Series Details ==
Series: HDMI 2.0: Scrambling support in DRM layer
URL : https://patchwork.freedesktop.org/series/18915/
State : failure
== Summary ==
CHECK usr/include/linux/byteorder/ (2 files) CHECK usr/include/linux/android/ (1 files) CHECK usr/include/linux/caif/ (2 files) CHECK usr/include/linux/iio/ (2 files) CHECK usr/include/linux/netfilter_ipv4/ (9 files) CHECK usr/include/linux/netfilter_bridge/ (17 files) CHECK usr/include/linux/can/ (5 files) CHECK usr/include/linux/raid/ (2 files) CHECK usr/include/linux/nfsd/ (5 files) CHECK usr/include/linux/hdlc/ (1 files) CHECK usr/include/linux/isdn/ (1 files) CHECK usr/include/linux/netfilter/ (87 files) CHECK usr/include/linux/tc_act/ (14 files) CHECK usr/include/linux/netfilter_arp/ (2 files) CHECK usr/include/linux/hsi/ (2 files) CHECK usr/include/linux/tc_ematch/ (4 files) CHECK usr/include/linux/mmc/ (1 files) CHECK usr/include/linux/dvb/ (8 files) CHECK usr/include/linux/sunrpc/ (1 files) CHECK usr/include/linux/wimax/ (1 files) CHECK usr/include/linux/spi/ (1 files) CHECK usr/include/linux/netfilter/ipset/ (4 files) CHECK usr/include/linux/usb/ (11 files) CHECK usr/include/linux/ (443 files) CHECK usr/include/linux/netfilter_ipv6/ (12 files) CHECK usr/include/asm/ (62 files) GEN .version CHK include/generated/compile.h UPD include/generated/compile.h CC init/version.o LD init/built-in.o LD vmlinux.o MODPOST vmlinux.o KSYM .tmp_kallsyms1.o KSYM .tmp_kallsyms2.o LD vmlinux SORTEX vmlinux SYSMAP System.map CC arch/x86/boot/a20.o AS arch/x86/boot/bioscall.o CC arch/x86/boot/cmdline.o HOSTCC arch/x86/boot/mkcpustr CC arch/x86/boot/early_serial_console.o CC arch/x86/boot/cpuflags.o CC arch/x86/boot/cpucheck.o AS arch/x86/boot/copy.o CC arch/x86/boot/edd.o CC arch/x86/boot/main.o AS arch/x86/boot/pmjump.o CC arch/x86/boot/printf.o CC arch/x86/boot/memory.o CC arch/x86/boot/regs.o CC arch/x86/boot/string.o CC arch/x86/boot/pm.o CC arch/x86/boot/video.o CC arch/x86/boot/version.o CC arch/x86/boot/video-vesa.o CC arch/x86/boot/video-vga.o CC arch/x86/boot/video-mode.o CC arch/x86/boot/video-bios.o CC arch/x86/boot/tty.o HOSTCC arch/x86/boot/tools/build Building modules, stage 2. LDS arch/x86/boot/compressed/vmlinux.lds AS arch/x86/boot/compressed/head_64.o VOFFSET arch/x86/boot/compressed/../voffset.h CPUSTR arch/x86/boot/cpustr.h CC arch/x86/boot/compressed/string.o MODPOST 97 modules CC arch/x86/boot/compressed/cmdline.o CC arch/x86/boot/compressed/error.o OBJCOPY arch/x86/boot/compressed/vmlinux.bin HOSTCC arch/x86/boot/compressed/mkpiggy CC arch/x86/boot/compressed/early_serial_console.o CC arch/x86/boot/compressed/eboot.o AS arch/x86/boot/compressed/efi_stub_64.o CC arch/x86/boot/cpu.o CC arch/x86/boot/compressed/cpuflags.o XZKERN arch/x86/boot/compressed/vmlinux.bin.xz
ERROR: "drm_enable_scrambling" [drivers/gpu/drm/i915/i915.ko] undefined! scripts/Makefile.modpost:91: recipe for target '__modpost' failed make[1]: *** [__modpost] Error 1
Makefile:1196: recipe for target 'modules' failed
make: *** [modules] Error 2
make: *** Waiting for unfinished jobs....
CC arch/x86/boot/compressed/misc.o
MKPIGGY arch/x86/boot/compressed/piggy.S
AS arch/x86/boot/compressed/piggy.o
DATAREL arch/x86/boot/compressed/vmlinux
LD arch/x86/boot/compressed/vmlinux
ZOFFSET arch/x86/boot/zoffset.h
OBJCOPY arch/x86/boot/vmlinux.bin
AS arch/x86/boot/header.o
LD arch/x86/boot/setup.elf
OBJCOPY arch/x86/boot/setup.bin
BUILD arch/x86/boot/bzImage
Setup is 16412 bytes (padded to 16896 bytes).
System is 4853 kB
CRC e574db06
Kernel: arch/x86/boot/bzImage is ready (#1)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: ✗ Fi.CI.BAT: failure for HDMI 2.0: Scrambling support in DRM layer
I build bzImage, keeping I915 as part of kernel (not as a module) Looks like I need to add EXPORT_SYMBOL(drm_enable_scrambling) Will cover this in V2.
Regards
Shashank
-----Original Message-----
From: Patchwork [mailto:[email protected]]
Sent: Wednesday, February 1, 2017 6:33 PM
To: Sharma, Shashank <[email protected]>
Cc: [email protected]
Subject: ✗ Fi.CI.BAT: failure for HDMI 2.0: Scrambling support in DRM layer
== Series Details ==
Series: HDMI 2.0: Scrambling support in DRM layer
URL : https://patchwork.freedesktop.org/series/18915/
State : failure
== Summary ==
CHECK usr/include/linux/byteorder/ (2 files) CHECK usr/include/linux/android/ (1 files) CHECK usr/include/linux/caif/ (2 files) CHECK usr/include/linux/iio/ (2 files) CHECK usr/include/linux/netfilter_ipv4/ (9 files) CHECK usr/include/linux/netfilter_bridge/ (17 files) CHECK usr/include/linux/can/ (5 files) CHECK usr/include/linux/raid/ (2 files) CHECK usr/include/linux/nfsd/ (5 files) CHECK usr/include/linux/hdlc/ (1 files) CHECK usr/include/linux/isdn/ (1 files) CHECK usr/include/linux/netfilter/ (87 files) CHECK usr/include/linux/tc_act/ (14 files) CHECK usr/include/linux/netfilter_arp/ (2 files) CHECK usr/include/linux/hsi/ (2 files) CHECK usr/include/linux/tc_ematch/ (4 files) CHECK usr/include/linux/mmc/ (1 files) CHECK usr/include/linux/dvb/ (8 files) CHECK usr/include/linux/sunrpc/ (1 files) CHECK usr/include/linux/wimax/ (1 files) CHECK usr/include/linux/spi/ (1 files) CHECK usr/include/linux/netfilter/ipset/ (4 files) CHECK usr/include/linux/usb/ (11 files) CHECK usr/include/linux/ (443 files) CHECK usr/include/linux/netfilter_ipv6/ (12 files) CHECK usr/include/asm/ (62 files) GEN .version CHK include/generated/compile.h UPD include/generated/compile.h CC init/version.o LD init/built-in.o LD vmlinux.o MODPOST vmlinux.o KSYM .tmp_kallsyms1.o KSYM .tmp_kallsyms2.o LD vmlinux SORTEX vmlinux SYSMAP System.map CC arch/x86/boot/a20.o AS arch/x86/boot/bioscall.o CC arch/x86/boot/cmdline.o HOSTCC arch/x86/boot/mkcpustr CC arch/x86/boot/early_serial_console.o CC arch/x86/boot/cpuflags.o CC arch/x86/boot/cpucheck.o AS arch/x86/boot/copy.o CC arch/x86/boot/edd.o CC arch/x86/boot/main.o AS arch/x86/boot/pmjump.o CC arch/x86/boot/printf.o CC arch/x86/boot/memory.o CC arch/x86/boot/regs.o CC arch/x86/boot/string.o CC arch/x86/boot/pm.o CC arch/x86/boot/video.o CC arch/x86/boot/version.o CC arch/x86/boot/video-vesa.o CC arch/x86/boot/video-vga.o CC arch/x86/boot/video-mode.o CC arch/x86/boot/video-bios.o CC arch/x86/boot/tty.o HOSTCC arch/x86/boot/tools/build Building modules, stage 2. LDS arch/x86/boot/compressed/vmlinux.lds AS arch/x86/boot/compressed/head_64.o VOFFSET arch/x86/boot/compressed/../voffset.h CPUSTR arch/x86/boot/cpustr.h CC arch/x86/boot/compressed/string.o MODPOST 97 modules CC arch/x86/boot/compressed/cmdline.o CC arch/x86/boot/compressed/error.o OBJCOPY arch/x86/boot/compressed/vmlinux.bin HOSTCC arch/x86/boot/compressed/mkpiggy CC arch/x86/boot/compressed/early_serial_console.o CC arch/x86/boot/compressed/eboot.o AS arch/x86/boot/compressed/efi_stub_64.o CC arch/x86/boot/cpu.o CC arch/x86/boot/compressed/cpuflags.o XZKERN arch/x86/boot/compressed/vmlinux.bin.xz
ERROR: "drm_enable_scrambling" [drivers/gpu/drm/i915/i915.ko] undefined! scripts/Makefile.modpost:91: recipe for target '__modpost' failed make[1]: *** [__modpost] Error 1
Makefile:1196: recipe for target 'modules' failed
make: *** [modules] Error 2
make: *** Waiting for unfinished jobs....
CC arch/x86/boot/compressed/misc.o
MKPIGGY arch/x86/boot/compressed/piggy.S
AS arch/x86/boot/compressed/piggy.o
DATAREL arch/x86/boot/compressed/vmlinux
LD arch/x86/boot/compressed/vmlinux
ZOFFSET arch/x86/boot/zoffset.h
OBJCOPY arch/x86/boot/vmlinux.bin
AS arch/x86/boot/header.o
LD arch/x86/boot/setup.elf
OBJCOPY arch/x86/boot/setup.bin
BUILD arch/x86/boot/bzImage
Setup is 16412 bytes (padded to 16896 bytes).
System is 4853 kB
CRC e574db06
Kernel: arch/x86/boot/bzImage is ready (#1)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx