clk: rockchip: mark pclk_uart2 as critical on rk3328
Subsystems (2)
PATCH 1/1 clk: rockchip: mark pclk_uart2 as critical on rk3328
The rk3328 uart2 port is used as boot console and to debug. During the boot pclk_uart2 is disabled by a clk_disable_unused initcall. Fix the uart2 function by marking pclk_uart2 as critical on rk3328. Also add sclk_uart2 as that is needed for the same DT node.
--- drivers/clk/rockchip/clk-rk3328.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/clk/rockchip/clk-rk3328.c +2 -0
@@ -875,6 +875,8 @@ static const char *const rk3328_critical_clocks[] __initconst = {"aclk_gmac_niu" ,"pclk_gmac_niu" ,"pclk_phy_niu" , +"pclk_uart2" , + "sclk_uart2", };static void __init rk3328_clk_init (struct device_node *np)
Signature · 1 line
2.11.0
Quoted 5 lines · Johan Jonker
The rk3328 uart2 port is used as boot console and to debug. During the boot
pclk_uart2is disabled by aclk_disable_unusedinitcall. Fix the uart2 function by markingpclk_uart2as critical on rk3328. Also addsclk_uart2as that is needed for the same DT node.
Hmm, given that those are named in the DT as the "baudclk" and "apb_pclk" that dw8250_probe() explicitly claims, they really shouldn't be unused :/
On my RK3328 box they appear to be prepared and enabled OK:
[robin@nemulon-9 ~]$ sudo grep uart2 /sys/kernel/debug/clk/clk_summary
sclk_uart2 1 1 0 24000000 0 0 50000
pclk_uart2 1 1 0 75000000 0 0 50000...
Robin.
Quoted 19 lines
Signed-off-by Johan Jonker <[email protected]>--- drivers/clk/rockchip/clk-rk3328.c | 2 ++ 1 file changed, 2 insertions(+)drivers/clk/rockchip/clk-rk3328.c +2
-0@@ -875,6 +875,8 @@ static const char *const rk3328_critical_clocks[] __initconst = {"aclk_gmac_niu" ,"pclk_gmac_niu" ,"pclk_phy_niu" , +"pclk_uart2" , + "sclk_uart2", };static void __init rk3328_clk_init (struct device_node *np)
Hi Robin and others,
Just a clarification.
Test is done on rk3318 A95X Z2 that uses rk3328.dtsi. Almost everything works fine now except for uart2. Front display also works now with ported custom vfd driver for the SM1628 clone used.
When I include a printk function for debugging in clk_disable_unused_subtree I get this list of disabled clocks below. Could you list the rk3328 clocks that are turned off? Is there a difference?
boot options including:
earlycon=uart8250,mmio32,0xff130000,keep
console=ttyS2,1500000n8
But the real console in which one can type ends up on ttyUSB0. Without console defined in the command line it's only usb keyboard and hdmi monitor. Output on ttyS2 stops right after:
[ 1.309231] C:pclk_uart2 -> pclk_bus
To see more I have to include clk_ignore_unused to the command line. In clk-px30.c they also included pclk_uart2 to the critical list. Could Elaine Zhang give more info on that?
Kind regards,
Johan Jonker
static void __init clk_disable_unused_subtree(struct clk_core *core)
{
struct clk_core *child;
unsigned long flags;
lockdep_assert_held(&prepare_lock);
hlist_for_each_entry(child, &core->children, child_node)
clk_disable_unused_subtree(child);
if (core->flags & CLK_OPS_PARENT_ENABLE)
clk_core_prepare_enable(core->parent);
if (clk_pm_runtime_get(core))
goto unprepare_out;
flags = clk_enable_lock();
if (core->enable_count)
goto unlock_out;
if (core->flags & CLK_IGNORE_UNUSED)
goto unlock_out;
/*
* some gate clocks have special needs during the disable-unused
* sequence. call .disable_unused if available, otherwise fall
* back to .disable
*/
if (clk_core_is_enabled(core)) {
trace_clk_disable(core);////////////
// >>> Include debug here <<<
printk("C:%s -> %s\n", core->name, core->parent ? core->parent->name :"*");
////////////
if (core->ops->disable_unused) core->ops->disable_unused(core->hw); else if (core->ops->disable) core->ops->disable(core->hw); trace_clk_disable_complete(core); }
unlock_out:
clk_enable_unlock(flags); clk_pm_runtime_put(core); unprepare_out: if (core->flags & CLK_OPS_PARENT_ENABLE) clk_core_disable_unprepare(core->parent); }
label kernel
kernel /Image-CLK
fdt /rk3318-a95x-z2-CYX-led.dtb
append root=/dev/mmcblk0p5 console=tty0 console=ttyUSB0,115200n8console=ttyS2,1500000n8 initcall_debug=1 debug drm.debug=0xe earlycon=uart8250,mmio32,0xff130000,keep swiotlb=1 kpti=0 no_console_suspend=1 consoleblank=0 rootwait
[ 1.282096] calling clk_disable_unused+0x0/0x110 @ 1 [ 1.282705] C:sclk_timer5 -> xin24m [ 1.283115] C:sclk_timer4 -> xin24m [ 1.283524] C:sclk_timer3 -> xin24m [ 1.283932] C:sclk_timer2 -> xin24m [ 1.284340] C:sclk_timer1 -> xin24m [ 1.284748] C:sclk_timer0 -> xin24m [ 1.285158] C:clk_otp -> xin24m [ 1.285536] C:aclk_mac2io -> aclk_gmac [ 1.286035] C:pclk_mac2io -> pclk_gmac [ 1.286483] C:clk_rga -> gpll [ 1.286834] C:aclk_gpu -> aclk_gpu_pre [ 1.287284] C:aclk_tsp -> aclk_bus_pre [ 1.287723] C:aclk_dcf -> aclk_bus_pre [ 1.288162] C:pclk_acodecphy -> pclk_phy_pre [ 1.295372] C:pclk_dcf -> pclk_bus [ 1.309231] C:pclk_uart2 -> pclk_bus [ 1.322902] C:pclk_uart1 -> pclk_bus [ 1.329133] C:pclk_uart0 -> pclk_bus [ 1.335230] C:pclk_spi -> pclk_bus [ 1.341538] C:pclk_stimer -> pclk_bus [ 1.341543] C:pclk_i2c3 -> pclk_bus [ 1.341547] C:pclk_i2c2 -> pclk_bus [ 1.341551] C:pclk_i2c1 -> pclk_bus [ 1.341554] C:pclk_i2c0 -> pclk_bus [ 1.341562] C:hclk_pdm -> hclk_bus_pre [ 1.341566] C:hclk_crypto_slv -> hclk_bus_pre [ 1.341574] C:hclk_crypto_mst -> hclk_bus_pre [ 1.395518] C:hclk_tsp -> hclk_bus_pre [ 1.401131] C:hclk_spdif_8ch -> hclk_bus_pre [ 1.406791] C:hclk_i2s2_2ch -> hclk_bus_pre [ 1.421229] C:hclk_i2s1_8ch -> hclk_bus_pre [ 1.426642] C:hclk_i2s0_8ch -> hclk_bus_pre [ 1.431878] C:clk_wifi -> cpll [ 1.436987] C:sclk_vdec_core -> cpll [ 1.442045] C:sclk_vdec_cabac -> cpll [ 1.446982] C:aclk_rga -> aclk_rga_pre [ 1.451825] C:aclk_hdcp -> aclk_vio_pre [ 1.456574] C:aclk_cif -> aclk_vio_pre [ 1.461226] C:aclk_iep -> aclk_vio_pre [ 1.465794] C:pclk_hdcp -> hclk_vio_pre [ 1.470401] C:hclk_hdcp -> hclk_vio_pre [ 1.470406] C:hclk_rga -> hclk_vio_pre [ 1.470411] C:hclk_cif -> hclk_vio_pre [ 1.470415] C:hclk_iep -> hclk_vio_pre [ 1.470424] C:clk_mac2io_out -> cpll [ 1.470432] C:clk_mac2io_ref -> clk_mac2io [ 1.470440] C:clk_mac2io_rx -> clk_mac2io [ 1.507448] C:clk_mac2io_tx -> clk_mac2io [ 1.511778] C:clk_mac2io_refout -> clk_mac2io [ 1.516094] C:clk_mac2io_src -> cpll [ 1.520315] C:clk_ref_usb3otg_src -> cpll [ 1.524560] C:clk_sdmmc_ext -> cpll [ 1.528701] C:hclk_sdmmc_ext -> hclk_peri [ 1.532850] C:clk_cif_src -> cpll [ 1.536945] C:sclk_venc_dsp -> cpll [ 1.541006] C:sclk_venc_core -> cpll [ 1.544972] C:aclk_h264 -> aclk_rkvenc [ 1.548936] C:aclk_h265 -> aclk_rkvenc [ 1.552794] C:hclk_h264 -> hclk_rkvenc [ 1.556580] C:pclk_h265 -> hclk_rkvenc [ 1.560373] C:aclk_rkvdec -> aclk_rkvdec_pre [ 1.564227] C:hclk_rkvdec -> hclk_rkvdec_pre [ 1.568096] C:clk_spi -> cpll [ 1.571981] C:clk_crypto -> cpll [ 1.575897] C:clk_i2c3 -> cpll [ 1.579795] C:clk_i2c2 -> cpll [ 1.583657] C:clk_i2c1 -> cpll [ 1.587521] C:clk_i2c0 -> cpll [ 1.591357] C:i2s2_out -> clk_i2s2 [ 1.595170] C:clk_i2s2 -> i2s2_pre [ 1.599020] C:i2s1_out -> clk_i2s1 [ 1.602893] C:clk_i2s1 -> i2s1_pre [ 1.606749] C:clk_i2s0 -> i2s0_pre [ 1.610519] C:clk_tsp -> cpll [ 1.614239] C:clk_pdm -> apll [ 1.617877] C:clk_hsadc_tsp -> * [ 1.621718] initcall clk_disable_unused+0x0/0x110 returned 0 after
331056 usecs
Quoted 39 lines · Robin Murphy
Quoted 5 lines · Johan Jonker
The rk3328 uart2 port is used as boot console and to debug. During the boot
pclk_uart2is disabled by aclk_disable_unusedinitcall. Fix the uart2 function by markingpclk_uart2as critical on rk3328. Also addsclk_uart2as that is needed for the same DT node.Hmm, given that those are named in the DT as the "baudclk" and "
apb_pclk" thatdw8250_probe()explicitly claims, they really shouldn't be unused :/On my RK3328 box they appear to be prepared and enabled OK:
[robin@nemulon-9 ~]$ sudo grep uart2
/sys/kernel/debug/clk/clk_summarysclk_uart2 1 1 0 24000000 0 0 50000 pclk_uart2 1 1 0 75000000 0 0 50000...
Robin.
Quoted 19 lines
Signed-off-by Johan Jonker <[email protected]>--- drivers/clk/rockchip/clk-rk3328.c | 2 ++ 1 file changed, 2 insertions(+)drivers/clk/rockchip/clk-rk3328.c +2
-0@@ -875,6 +875,8 @@ static const char *const rk3328_critical_clocks[] __initconst = {"aclk_gmac_niu" ,"pclk_gmac_niu" ,"pclk_phy_niu" , +"pclk_uart2" , + "sclk_uart2", };static void __init rk3328_clk_init (struct device_node *np)
Quoted 11 lines · Johan Jonker
Hi Robin and others,
Just a clarification.
Test is done on rk3318 A95X Z2 that usesrk3328.dtsi. Almost everything works fine now except for uart2. Front display also works now with ported custom vfd driver for the SM1628 clone used.When I include a printk function for debugging in
clk_disable_unused_subtreeI get this list of disabled clocks below. Could you list the rk3328 clocks that are turned off? Is there a difference?
I couldn't be bothered to rebuild a modified kernel package, so I just rebooted with "trace_event=clk_disable,clk_enable":
[robin@nemulon-9 ~]$ sudo grep uart /sys/kernel/debug/tracing/trace
<idle>-0 [000] d... 0.000000: clk_enable: clk_uart2_div
<idle>-0 [000] d... 0.000000: clk_enable: clk_uart2_frac
<idle>-0 [000] d... 0.000000: clk_disable: clk_uart2_frac
<idle>-0 [000] d... 0.000000: clk_disable: clk_uart2_div
<idle>-0 [000] d... 0.000000: clk_enable: clk_uart1_div
<idle>-0 [000] d... 0.000000: clk_enable: clk_uart1_frac
<idle>-0 [000] d... 0.000000: clk_disable: clk_uart1_frac
<idle>-0 [000] d... 0.000000: clk_disable: clk_uart1_div
<idle>-0 [000] d... 0.000000: clk_enable: clk_uart0_div
<idle>-0 [000] d... 0.000000: clk_enable: clk_uart0_frac
<idle>-0 [000] d... 0.000000: clk_disable: clk_uart0_frac
<idle>-0 [000] d... 0.000000: clk_disable: clk_uart0_div
swapper/0-1 [002] d... 5.397599: clk_enable: sclk_uart2
swapper/0-1 [002] d... 5.397619: clk_enable: pclk_uart2
swapper/0-1 [002] d... 5.398056: clk_disable: sclk_uart2
swapper/0-1 [002] d... 5.398081: clk_enable: sclk_uart2
swapper/0-1 [003] d... 5.716848: clk_disable: pclk_uart1
swapper/0-1 [003] d... 5.716850: clk_disable: pclk_uart0
swapper/0-1 [003] d... 5.718596: clk_disable: sclk_uart2
swapper/0-1 [003] d... 5.718612: clk_enable: sclk_uart2
(agetty)-554 [003] d... 12.662968: clk_disable: sclk_uart2
(agetty)-554 [003] d... 12.662995: clk_enable: sclk_uart2This looks as I would expect - UART2 is the only one enabled in DT, so pclk_uart2 gets enabled when the driver loads and stays that way, while the events for pclk_uart{0,1} correlate with clk_disable_unused() running at the final round of initcalls:
[ 5.398003] ff130000.serial: ttyS2 at MMIO 0xff130000 (irq = 14, base_baud = 1500000) is a 16550A [ 5.470655] printk: console [ttyS2] enabled ... [ 5.756099] Run /init as init process
FWIW I have "earlycon=uart8250,mmio32,0xff130000" on my command line, but no explicit console argument - that's going to ttyS2 by virtue of the DT "stdout-path".
Robin.
Quoted 204 lines
boot options including:
earlycon=uart8250,mmio32,0xff130000,keep
console=ttyS2,1500000n8But the real console in which one can type ends up on ttyUSB0. Without console defined in the command line it's only usb keyboard and hdmi monitor. Output on ttyS2 stops right after:
[ 1.309231] C:pclk_uart2 -> pclk_busTo see more I have to include
clk_ignore_unusedto the command line. Inclk-px30.cthey also includedpclk_uart2to the critical list. Could Elaine Zhang give more info on that?Kind regards,
Johan Jonker
static void
__initclk_disable_unused_subtree(struct clk_core *core){ struct clk_core *child; unsigned long flags; lockdep_assert_held(&prepare_lock); hlist_for_each_entry(child, &core->children, child_node) clk_disable_unused_subtree(child); if (core->flags & CLK_OPS_PARENT_ENABLE) clk_core_prepare_enable(core->parent); if (clk_pm_runtime_get(core)) goto unprepare_out; flags = clk_enable_lock(); if (core->enable_count) goto unlock_out; if (core->flags & CLK_IGNORE_UNUSED) goto unlock_out; /* * some gate clocks have special needs during the disable-unused * sequence. call .disable_unused if available, otherwise fall * back to .disable */ if (clk_core_is_enabled(core)) { trace_clk_disable(core);////////////
// >>> Include debug here <<<printk("C:%s -> %s\n", core->name, core->parent ? core->parent->name :"*");
////////////
if (core->ops->disable_unused) core->ops->disable_unused(core->hw); else if (core->ops->disable) core->ops->disable(core->hw); trace_clk_disable_complete(core); }
unlock_out:clk_enable_unlock(flags); clk_pm_runtime_put(core); unprepare_out: if (core->flags & CLK_OPS_PARENT_ENABLE) clk_core_disable_unprepare(core->parent); }label kernel
kernel /Image-CLK fdt /rk3318-a95x-z2-CYX-led.dtb append root=/dev/mmcblk0p5 console=tty0 console=ttyUSB0,115200n8console=ttyS2,1500000n8 initcall_debug=1 debug drm.debug=0xe earlycon=uart8250,mmio32,0xff130000,keep swiotlb=1 kpti=0 no_console_suspend=1 consoleblank=0 rootwait
[ 1.282096] calling clk_disable_unused+0x0/0x110 @ 1 [ 1.282705] C:sclk_timer5 -> xin24m [ 1.283115] C:sclk_timer4 -> xin24m [ 1.283524] C:sclk_timer3 -> xin24m [ 1.283932] C:sclk_timer2 -> xin24m [ 1.284340] C:sclk_timer1 -> xin24m [ 1.284748] C:sclk_timer0 -> xin24m [ 1.285158] C:clk_otp -> xin24m [ 1.285536] C:aclk_mac2io -> aclk_gmac [ 1.286035] C:pclk_mac2io -> pclk_gmac [ 1.286483] C:clk_rga -> gpll [ 1.286834] C:aclk_gpu -> aclk_gpu_pre [ 1.287284] C:aclk_tsp -> aclk_bus_pre [ 1.287723] C:aclk_dcf -> aclk_bus_pre [ 1.288162] C:pclk_acodecphy -> pclk_phy_pre [ 1.295372] C:pclk_dcf -> pclk_bus [ 1.309231] C:pclk_uart2 -> pclk_bus [ 1.322902] C:pclk_uart1 -> pclk_bus [ 1.329133] C:pclk_uart0 -> pclk_bus [ 1.335230] C:pclk_spi -> pclk_bus [ 1.341538] C:pclk_stimer -> pclk_bus [ 1.341543] C:pclk_i2c3 -> pclk_bus [ 1.341547] C:pclk_i2c2 -> pclk_bus [ 1.341551] C:pclk_i2c1 -> pclk_bus [ 1.341554] C:pclk_i2c0 -> pclk_bus [ 1.341562] C:hclk_pdm -> hclk_bus_pre [ 1.341566] C:hclk_crypto_slv -> hclk_bus_pre [ 1.341574] C:hclk_crypto_mst -> hclk_bus_pre [ 1.395518] C:hclk_tsp -> hclk_bus_pre [ 1.401131] C:hclk_spdif_8ch -> hclk_bus_pre [ 1.406791] C:hclk_i2s2_2ch -> hclk_bus_pre [ 1.421229] C:hclk_i2s1_8ch -> hclk_bus_pre [ 1.426642] C:hclk_i2s0_8ch -> hclk_bus_pre [ 1.431878] C:clk_wifi -> cpll [ 1.436987] C:sclk_vdec_core -> cpll [ 1.442045] C:sclk_vdec_cabac -> cpll [ 1.446982] C:aclk_rga -> aclk_rga_pre [ 1.451825] C:aclk_hdcp -> aclk_vio_pre [ 1.456574] C:aclk_cif -> aclk_vio_pre [ 1.461226] C:aclk_iep -> aclk_vio_pre [ 1.465794] C:pclk_hdcp -> hclk_vio_pre [ 1.470401] C:hclk_hdcp -> hclk_vio_pre [ 1.470406] C:hclk_rga -> hclk_vio_pre [ 1.470411] C:hclk_cif -> hclk_vio_pre [ 1.470415] C:hclk_iep -> hclk_vio_pre [ 1.470424] C:clk_mac2io_out -> cpll [ 1.470432] C:clk_mac2io_ref -> clk_mac2io [ 1.470440] C:clk_mac2io_rx -> clk_mac2io [ 1.507448] C:clk_mac2io_tx -> clk_mac2io [ 1.511778] C:clk_mac2io_refout -> clk_mac2io [ 1.516094] C:clk_mac2io_src -> cpll [ 1.520315] C:clk_ref_usb3otg_src -> cpll [ 1.524560] C:clk_sdmmc_ext -> cpll [ 1.528701] C:hclk_sdmmc_ext -> hclk_peri [ 1.532850] C:clk_cif_src -> cpll [ 1.536945] C:sclk_venc_dsp -> cpll [ 1.541006] C:sclk_venc_core -> cpll [ 1.544972] C:aclk_h264 -> aclk_rkvenc [ 1.548936] C:aclk_h265 -> aclk_rkvenc [ 1.552794] C:hclk_h264 -> hclk_rkvenc [ 1.556580] C:pclk_h265 -> hclk_rkvenc [ 1.560373] C:aclk_rkvdec -> aclk_rkvdec_pre [ 1.564227] C:hclk_rkvdec -> hclk_rkvdec_pre [ 1.568096] C:clk_spi -> cpll [ 1.571981] C:clk_crypto -> cpll [ 1.575897] C:clk_i2c3 -> cpll [ 1.579795] C:clk_i2c2 -> cpll [ 1.583657] C:clk_i2c1 -> cpll [ 1.587521] C:clk_i2c0 -> cpll [ 1.591357] C:i2s2_out -> clk_i2s2 [ 1.595170] C:clk_i2s2 -> i2s2_pre [ 1.599020] C:i2s1_out -> clk_i2s1 [ 1.602893] C:clk_i2s1 -> i2s1_pre [ 1.606749] C:clk_i2s0 -> i2s0_pre [ 1.610519] C:clk_tsp -> cpll [ 1.614239] C:clk_pdm -> apll [ 1.617877] C:clk_hsadc_tsp -> * [ 1.621718] initcall clk_disable_unused+0x0/0x110 returned 0 after331056 usecs
Quoted 39 lines · Robin Murphy
Quoted 5 lines · Johan Jonker
The rk3328 uart2 port is used as boot console and to debug. During the boot
pclk_uart2is disabled by aclk_disable_unusedinitcall. Fix the uart2 function by markingpclk_uart2as critical on rk3328. Also addsclk_uart2as that is needed for the same DT node.Hmm, given that those are named in the DT as the "baudclk" and "
apb_pclk" thatdw8250_probe()explicitly claims, they really shouldn't be unused :/On my RK3328 box they appear to be prepared and enabled OK:
[robin@nemulon-9 ~]$ sudo grep uart2
/sys/kernel/debug/clk/clk_summarysclk_uart2 1 1 0 24000000 0 0 50000 pclk_uart2 1 1 0 75000000 0 0 50000...
Robin.
Quoted 19 lines
Signed-off-by Johan Jonker <[email protected]>--- drivers/clk/rockchip/clk-rk3328.c | 2 ++ 1 file changed, 2 insertions(+)drivers/clk/rockchip/clk-rk3328.c +2
-0@@ -875,6 +875,8 @@ static const char *const rk3328_critical_clocks[] __initconst = {"aclk_gmac_niu" ,"pclk_gmac_niu" ,"pclk_phy_niu" , +"pclk_uart2" , + "sclk_uart2", };static void __init rk3328_clk_init (struct device_node *np)
Quoted 16 lines · Johan Jonker
The rk3328 uart2 port is used as boot console and to debug. During the boot
pclk_uart2is disabled by aclk_disable_unusedinitcall. Fix the uart2 function by markingpclk_uart2as critical on rk3328. Also addsclk_uart2as that is needed for the same DT node.Signed-off-by Johan Jonker <[email protected]>--- drivers/clk/rockchip/clk-rk3328.c | 2 ++ 1 file changed, 2 insertions(+)drivers/clk/rockchip/clk-rk3328.c +0
-0
drivers/clk/rockchip/clk-rk3328.c static const char *const rk3328_critical_clocks[] __initconst = { · line 881
Quoted 7 lines
drivers/clk/rockchip/clk-rk3328.c +2
-0@@ -875,6 +875,8 @@ static const char *const rk3328_critical_clocks[] __initconst = {"aclk_gmac_niu" ,"pclk_gmac_niu" ,"pclk_phy_niu" , +"pclk_uart2" , + "sclk_uart2", };
Not need to mark the uart2 as critical clocks, the uart clk will enabled by uart driver probe(dw8250_probe()).
For your question, Please check the uart2 dts node "status = okay".
Or You can send me the complete log, I check the status of uart2.
Quoted 1 line
drivers/clk/rockchip/clk-rk3328.c +0
-0static void __init rk3328_clk_init (struct device_node *np)
Hi Elaine, Robin,
Thank you for your help!
This patch can go in the garbage bin.
It turns out that with SERIAL_8250 also SERIAL_8250_DW must be selected... ;)
It's not in the Kconfig help description. Shouldn't that be automatically be included for Rockchip? Example:
config SERIAL_8250
tristate "8250/16550 and compatible serial support" depends on !S390
select SERIAL_CORE
select SERIAL_MCTRL_GPIO if GPIOLIB
select SERIAL_8250_DW if ARCH_ROCKCHIP
Thank Robin for the introduction to FTRACE!
mount -t tracefs tracefs /sys/kernel/tracing
cd /sys/kernel/tracing
# Without SERIAL_8250_DW
/sys/kernel/tracing # cat trace | grep uart2
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div
swapper/0-1 [002] d..1 1.916746: clk_disable: pclk_uart2/sys/kernel/tracing # cat trace | grep uart
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_div
swapper/0-1 [002] d..1 1.916746: clk_disable: pclk_uart2
swapper/0-1 [002] d..1 1.923959: clk_disable: pclk_uart1
swapper/0-1 [002] d..1 1.930741: clk_disable: pclk_uart0# With SERIAL_8250_DW
/sys/kernel/tracing # cat trace | grep uart2
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div
swapper/0-1 [002] d..1 0.923180: clk_enable: sclk_uart2
swapper/0-1 [002] d..1 0.923224: clk_enable: pclk_uart2
swapper/0-1 [002] d..1 0.925259: clk_disable: sclk_uart2
swapper/0-1 [002] d..1 0.925295: clk_enable: sclk_uart2
swapper/0-1 [003] d..1 2.208605: clk_disable: sclk_uart2
swapper/0-1 [003] d..1 2.208646: clk_enable: sclk_uart2/sys/kernel/tracing # cat trace | grep uart
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_div
<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_frac
<idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_div
swapper/0-1 [002] d..1 0.920034: clk_enable: sclk_uart0
swapper/0-1 [002] d..1 0.920085: clk_enable: pclk_uart0
kworker/2:1-32 [002] d..1 0.922596: clk_disable: sclk_uart0
kworker/2:1-32 [002] d..1 0.922613: clk_disable: pclk_uart0
swapper/0-1 [002] d..1 0.923180: clk_enable: sclk_uart2
swapper/0-1 [002] d..1 0.923224: clk_enable: pclk_uart2
swapper/0-1 [002] d..1 0.925259: clk_disable: sclk_uart2
swapper/0-1 [002] d..1 0.925295: clk_enable: sclk_uart2
swapper/0-1 [003] d..1 1.914158: clk_disable: pclk_uart1
swapper/0-1 [003] d..1 2.208605: clk_disable: sclk_uart2
swapper/0-1 [003] d..1 2.208646: clk_enable: sclk_uart2Quoted 37 lines · elaine.zhang
Quoted 24 lines · Johan Jonker
The rk3328 uart2 port is used as boot console and to debug. During the boot
pclk_uart2is disabled by aclk_disable_unusedinitcall. Fix the uart2 function by markingpclk_uart2as critical on rk3328. Also addsclk_uart2as that is needed for the same DT node.Signed-off-by Johan Jonker <[email protected]>---
drivers/clk/rockchip/clk-rk3328.c| 2 ++1 file changed, 2 insertions(+)drivers/clk/rockchip/clk-rk3328.c +2
-0@@ -875,6 +875,8 @@ static const char *const rk3328_critical_clocks[]__initconst = { "aclk_gmac_niu", "pclk_gmac_niu", "pclk_phy_niu", + "pclk_uart2", + "sclk_uart2", };Quoted 1 line
Not need to mark the uart2 as critical clocks, the uart clk will enabled by uart driver probe(dw8250_probe()).
For your question, Please check the uart2 dts node "status = okay".
Or You can send me the complete log, I check the status of uart2.
Quoted 1 line
static void
__initrk3328_clk_init(struct device_node *np)
Quoted 11 lines · Johan Jonker
Hi Elaine, Robin,
Thank you for your help!
This patch can go in the garbage bin.
It turns out that withSERIAL_8250alsoSERIAL_8250_DWmust be selected... ;)It's not in the
Kconfighelp description. Shouldn't that be automatically be included for Rockchip? Example:
Quoted 6 lines
config
SERIAL_8250
tristate "8250/16550 and compatible serial support" depends on !S390
selectSERIAL_CORE
selectSERIAL_MCTRL_GPIOif GPIOLIB
selectSERIAL_8250_DWifARCH_ROCKCHIP
Our Konfig:
config SERIAL_8250
tristate "8250/16550 and compatible serial support" depends on !S390
select SERIAL_CORE
config SERIAL_8250_DW
tristate "Support for Synopsys DesignWare 8250 quirks" depends on SERIAL_8250
So SERIAL_8250 and SERIAL_8250_DW must be selected.
If you use select SERIAL_8250_DW if ARCH_ROCKCHIP, check the CONIF_ARCH_ROCKCHIP=y. In our rockchip_defconfig the CONIF_ARCH_ROCKCHIP=y by default.
Quoted 113 lines
Thank Robin for the introduction to FTRACE!
mount -t tracefs tracefs
/sys/kernel/tracingcd
/sys/kernel/tracing# Without
SERIAL_8250_DW
/sys/kernel/tracing# cat trace | grep uart2<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div swapper/0-1 [002] d..1 1.916746: clk_disable: pclk_uart2
/sys/kernel/tracing# cat trace | grep uart<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_div swapper/0-1 [002] d..1 1.916746: clk_disable: pclk_uart2 swapper/0-1 [002] d..1 1.923959: clk_disable: pclk_uart1 swapper/0-1 [002] d..1 1.930741: clk_disable: pclk_uart0# With
SERIAL_8250_DW
/sys/kernel/tracing# cat trace | grep uart2<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div swapper/0-1 [002] d..1 0.923180: clk_enable: sclk_uart2 swapper/0-1 [002] d..1 0.923224: clk_enable: pclk_uart2 swapper/0-1 [002] d..1 0.925259: clk_disable: sclk_uart2 swapper/0-1 [002] d..1 0.925295: clk_enable: sclk_uart2 swapper/0-1 [003] d..1 2.208605: clk_disable: sclk_uart2 swapper/0-1 [003] d..1 2.208646: clk_enable: sclk_uart2
/sys/kernel/tracing# cat trace | grep uart<idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart2_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart1_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart1_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_div <idle>-0 [000] d..2 0.000000: clk_enable: clk_uart0_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_frac <idle>-0 [000] d..2 0.000000: clk_disable: clk_uart0_div swapper/0-1 [002] d..1 0.920034: clk_enable: sclk_uart0 swapper/0-1 [002] d..1 0.920085: clk_enable: pclk_uart0 kworker/2:1-32 [002] d..1 0.922596: clk_disable: sclk_uart0 kworker/2:1-32 [002] d..1 0.922613: clk_disable: pclk_uart0 swapper/0-1 [002] d..1 0.923180: clk_enable: sclk_uart2 swapper/0-1 [002] d..1 0.923224: clk_enable: pclk_uart2 swapper/0-1 [002] d..1 0.925259: clk_disable: sclk_uart2 swapper/0-1 [002] d..1 0.925295: clk_enable: sclk_uart2 swapper/0-1 [003] d..1 1.914158: clk_disable: pclk_uart1 swapper/0-1 [003] d..1 2.208605: clk_disable: sclk_uart2 swapper/0-1 [003] d..1 2.208646: clk_enable: sclk_uart2Quoted 35 lines · elaine.zhang
Quoted 17 lines · Johan Jonker
The rk3328 uart2 port is used as boot console and to debug. During the boot
pclk_uart2is disabled by aclk_disable_unusedinitcall. Fix the uart2 function by markingpclk_uart2as critical on rk3328. Also addsclk_uart2as that is needed for the same DT node.Signed-off-by Johan Jonker <[email protected]>--- drivers/clk/rockchip/clk-rk3328.c | 2 ++ 1 file changed, 2 insertions(+)drivers/clk/rockchip/clk-rk3328.c +0
-0drivers/clk/rockchip/clk-rk3328.c static const char *const rk3328_critical_clocks[] · line 882
Quoted 8 lines
drivers/clk/rockchip/clk-rk3328.c +2
-0@@ -875,6 +875,8 @@ static const char *const rk3328_critical_clocks[]__initconst = { "aclk_gmac_niu", "pclk_gmac_niu", "pclk_phy_niu", + "pclk_uart2", + "sclk_uart2", };Not need to mark the uart2 as critical clocks, the uart clk will enabled by uart driver probe(dw8250_probe()).
For your question, Please check the uart2 dts node "status = okay".
Or You can send me the complete log, I check the status of uart2.
Quoted 1 line
static void
__initrk3328_clk_init(struct device_node *np)