sunxi: add OrangePi Zero 3 board support
cover sunxi: add OrangePi Zero 3 board support
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC. Compared to its predecessor OrangePi Zero 2, the new board uses LPDDR4 DRAM instead of DDR3 DRAM, and an X-Powers AXP313 PMIC instead of the AXP305.
U-Boot gained support for both LPDDR4 DRAM and the new PMIC just recently, so add a user for those features by adding a defconfig for the new board.
To make this work, patch 1/3 introduces support for zBIT SPI NOR flash chip, and patch 2/3 removes the default AXP305 PMIC selection when compiling for H616 SoCs.
Patch 3/3 then adds the defconfig. The DT was already synced from the Linux kernel repo a few weeks ago.
Cheers,
Andre
Andre Przywara (3):
mtd: spi-nor: Add support for zBIT ZB25VQ128
sunxi: H616: remove default AXP305 selection
sunxi: H616: Add OrangePi Zero 3 board support
arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero2_defconfig | 1 + configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ configs/x96_mate_defconfig | 1 + drivers/mtd/spi/Kconfig | 5 +++++ drivers/mtd/spi/spi-nor-ids.c | 5 +++++ drivers/power/Kconfig | 1 - 8 files changed, 48 insertions(+), 1 deletion(-) create mode 100644 configs/orangepi_zero3_defconfig
Signature · 1 line
2.35.8
PATCH 1/3 mtd: spi-nor: Add support for zBIT ZB25VQ128
Add support for the zBIT ZB25VQ128 (128M-bit) SPI NOR flash memory chip, as used on the Xunlong Orange Pi Zero 3 board.
--- drivers/mtd/spi/Kconfig | 5 +++++ drivers/mtd/spi/spi-nor-ids.c | 5 +++++ 2 files changed, 10 insertions(+)
drivers/mtd/spi/Kconfig +5 -0
@@ -224,6 +224,11 @@ config SPI_FLASH_XTX Add support for various XTX (XTX Technology Limited) SPI flash chips (XT25xxx). +config SPI_FLASH_ZBIT + bool "ZBIT SPI flash support" + help + Add support for Zbit Semiconductor Inc. SPI flash chips (ZB25xxx). + endif config SPI_FLASH_USE_4K_SECTORS
drivers/mtd/spi/spi-nor-ids.c +5 -0
@@ -571,6 +571,11 @@ const struct flash_info spi_nor_ids[] = { SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, { INFO("xt25w01g", 0x0b651B, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, +#endif +#ifdef CONFIG_SPI_FLASH_ZBIT + /* Zbit Semiconductor Inc. */ + { INFO("zb25vq128", 0x5e4018, 0, 64 * 1024, 256, + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, #endif { }, };
Signature · 1 line
2.35.8
PATCH 2/3 sunxi: H616: remove default AXP305 selection
In reply to Andre PrzywaraThe original H616 devices released about three years ago were typically paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig, and move the PMIC selection into the board defconfig files instead.
--- configs/orangepi_zero2_defconfig | 1 + configs/x96_mate_defconfig | 1 + drivers/power/Kconfig | 1 - 3 files changed, 2 insertions(+), 1 deletion(-)
configs/orangepi_zero2_defconfig +1 -0
@@ -19,6 +19,7 @@ CONFIG_SYS_I2C_SPEED=400000 CONFIG_SPI_FLASH_MACRONIX=y CONFIG_PHY_REALTEK=y CONFIG_SUN8I_EMAC=y +CONFIG_AXP305_POWER=y CONFIG_SPI=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y
configs/x96_mate_defconfig +1 -0
@@ -18,6 +18,7 @@ CONFIG_SPL_SYS_I2C_LEGACY=y CONFIG_SYS_I2C_MVTWSI=y CONFIG_SYS_I2C_SLAVE=0x7f CONFIG_SYS_I2C_SPEED=400000 +CONFIG_AXP305_POWER=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y
drivers/power/Kconfig +0 -1
@@ -56,7 +56,6 @@ choice depends on ARCH_SUNXI default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 - default AXP305_POWER if MACH_SUN50I_H616 default AXP818_POWER if MACH_SUN8I_A83T default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_V3S
Signature · 1 line
2.35.8
Re: [PATCH 2/3] sunxi: H616: remove default AXP305 selection
Quoted 8 lines · Andre Przywara
The original H616 devices released about three years ago were typically paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the
Kconfig, and move the PMIC selection into the board defconfig files instead.Signed-off-by Andre Przywara <[email protected]>
Best Regards,
Jaehoon Chung
Quoted 42 lines
--- configs/orangepi_zero2_defconfig | 1 + configs/x96_mate_defconfig | 1 + drivers/power/Kconfig | 1 - 3 files changed, 2 insertions(+), 1 deletion(-)configs/orangepi_zero2_defconfig +1
-0@@ -19,6 +19,7 @@ CONFIG_SYS_I2C_SPEED=400000 CONFIG_SPI_FLASH_MACRONIX=y CONFIG_PHY_REALTEK=y CONFIG_SUN8I_EMAC=y +CONFIG_AXP305_POWER=y CONFIG_SPI=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=yconfigs/x96_mate_defconfig +1
-0@@ -18,6 +18,7 @@ CONFIG_SPL_SYS_I2C_LEGACY=y CONFIG_SYS_I2C_MVTWSI=y CONFIG_SYS_I2C_SLAVE=0x7f CONFIG_SYS_I2C_SPEED=400000 +CONFIG_AXP305_POWER=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=ydrivers/power/Kconfig +0
-1@@ -56,7 +56,6 @@ choice depends on ARCH_SUNXI default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 - default AXP305_POWER if MACH_SUN50I_H616 default AXP818_POWER if MACH_SUN8I_A83T default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_V3S
PATCH 3/3 sunxi: H616: Add OrangePi Zero 3 board support
In reply to Andre PrzywaraThe OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
--- arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+) create mode 100644 configs/orangepi_zero3_defconfig
arch/arm/dts/Makefile +1 -0
@@ -835,6 +835,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ sun50i-h616-orangepi-zero2.dtb \ + sun50i-h618-orangepi-zero3.dtb \ sun50i-h616-x96-mate.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \
board/sunxi/MAINTAINERS +5 -0
@@ -455,6 +455,11 @@ M: Jernej Skrabec <[email protected]> S: Maintained F: configs/orangepi_zero2_defconfig +ORANGEPI ZERO 3 BOARD +M: Andre Przywara <[email protected]> +S: Maintained +F: configs/orangepi_zero3_defconfig + ORANGEPI PC 2 BOARD M: Andre Przywara <[email protected]> S: Maintained
configs/orangepi_zero3_defconfig new file +30 -0
@@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e +CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 +CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 +CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR4=y +CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_SPI_FLASH_ZBIT=y +CONFIG_PHY_MOTORCOMM=y +CONFIG_SUN8I_EMAC=y +CONFIG_AXP313_POWER=y +CONFIG_SPI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y
Signature · 1 line
2.35.8
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
Hi Andre!
Thanks for your patches. I started checking and noticed that USB storage was not working:
=> usb reset
resetting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... 1 USB Device(s) found scanning bus usb@5200400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found => usb storage
No storage devices, perhaps not 'usb start'ed..?
Otherwise my OpiZero3 (4GB) board looks working.
Ethernet works with my 10 Mbps usb-dongle.
sf probe detect spi nor flash:
=> sf probe
SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Loading the kernel and running the operating system (from microsd) also without problems.
Quoted 85 lines · Andre Przywara
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the
Makefileto actually build the .dtb.The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+)create mode 100644 configs/orangepi_zero3_defconfig
arch/arm/dts/Makefile +1
-0@@ -835,6 +835,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ sun50i-h616-orangepi-zero2.dtb \ + sun50i-h618-orangepi-zero3.dtb \ sun50i-h616-x96-mate.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \board/sunxi/MAINTAINERS +5
-0@@ -455,6 +455,11 @@ M: Jernej Skrabec <[email protected]> S: Maintained F: configs/orangepi_zero2_defconfig +ORANGEPI ZERO 3 BOARD +M: Andre Przywara <[email protected]> +S: Maintained +F: configs/orangepi_zero3_defconfig + ORANGEPI PC 2 BOARD M: Andre Przywara <[email protected]> S: Maintainedconfigs/orangepi_zero3_defconfig new file +30
-0@@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e +CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 +CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 +CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR4=y +CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_SPI_FLASH_ZBIT=y +CONFIG_PHY_MOTORCOMM=y +CONFIG_SUN8I_EMAC=y +CONFIG_AXP313_POWER=y +CONFIG_SPI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
On Sat, 25 Nov 2023 20:43:12 +0300
Mikhail Kalashnikov <[email protected]> wrote:
Hi Mikhail,
Quoted 4 lines
Hi Andre!
Thanks for your patches. I started checking and noticed that USB storage was not working:
Quoted 9 lines
=> usb reset
resetting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... 1 USB Device(s) found scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> usb storage
No storage devices, perhaps not 'usb start'ed..?
Ah, thanks for the report, seems I didn't even test this!
So digging around I figured it's working in Linux, and it's the right USB port, but we are missing the VBUS power switch, which is a GPIO controlled regulator. There are pending patches to pick this from the devicetree[1], but we are not there yet, so we need:CONFIG_USB1_VBUS_PIN="PC16"
in the defconfig, for now. I will update the file. The same is actually missing from the OrangePi Zero2 defconfig, I will send a patch ASAP.
Quoted 8 lines
Otherwise my OpiZero3 (4GB) board looks working.
Ethernet works with my 10 Mbps usb-dongle.sf probe detect spi nor flash:
=> sf probe
SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
Quoted 4 lines
Loading the kernel and running the operating system (from microsd) also without problems.
Tested-by Mikhail Kalashnikov <[email protected]>
Great, thanks for the tag!
Cheers,
Andre
Quoted 87 lines · Andre Przywara
Quoted 85 lines
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the
Makefileto actually build the .dtb.The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+)create mode 100644 configs/orangepi_zero3_defconfig
arch/arm/dts/Makefile +1
-0@@ -835,6 +835,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ sun50i-h616-orangepi-zero2.dtb \ + sun50i-h618-orangepi-zero3.dtb \ sun50i-h616-x96-mate.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \board/sunxi/MAINTAINERS +5
-0@@ -455,6 +455,11 @@ M: Jernej Skrabec <[email protected]> S: Maintained F: configs/orangepi_zero2_defconfig +ORANGEPI ZERO 3 BOARD +M: Andre Przywara <[email protected]> +S: Maintained +F: configs/orangepi_zero3_defconfig + ORANGEPI PC 2 BOARD M: Andre Przywara <[email protected]> S: Maintainedconfigs/orangepi_zero3_defconfig new file +30
-0@@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e +CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 +CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 +CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR4=y +CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_SPI_FLASH_ZBIT=y +CONFIG_PHY_MOTORCOMM=y +CONFIG_SUN8I_EMAC=y +CONFIG_AXP313_POWER=y +CONFIG_SPI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110". I am not sure of the details of the boot.cmd. The output below came from the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.
I was able to install u-boot to the SPI flash memory and there is a warning message from that also: " Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning - spi_flash_probe_bus_cs() failed, using default environment"
Thank you for your advice on getting something to boot. None of the Debian installer images were suitable. Even SID was at 6.1. I built the latest Linux 6.6.2 and wrestled with the rootfs before I got it running. I built the tested u-boot with this system, as a test of system stability.
defconfig used + emac patches
CONFIG_ARM=yCONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" CONFIG_SPL=y CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f CONFIG_MACH_SUN50I_H616=y CONFIG_SUNXI_DRAM_H616_LPDDR4=y
#CONFIG_DRAM_CLK=792 CONFIG_USB1_VBUS_PIN="PC16"
#CONFIG_R_I2C_ENABLE=yCONFIG_SPL_SPI_SUNXI=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_I2C=yCONFIG_SPL_SYS_I2C_LEGACY=y CONFIG_SYS_I2C_MVTWSI=y CONFIG_SYS_I2C_SLAVE=0x7f CONFIG_SYS_I2C_SPEED=400000 CONFIG_SPI_FLASH_ZBIT=yCONFIG_PHY_MOTORCOMM=yCONFIG_SUN8I_EMAC=yCONFIG_AXP313_POWER=yCONFIG_SPI=yCONFIG_USB_EHCI_HCD=yCONFIG_USB_OHCI_HCD=yCONFIG_USB_MUSB_GADGET=y
Console Output:
U-Boot 2024.01-rc3-00009-g9e53e45292-dirty (Nov 25 2023 - 18:32:16 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiB Core: 57 devices, 25 uclasses, devicetree: separate WDT: Not starting watchdog@30090a0 MMC: mmc@4020000: 0
Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning - spi_flash_probe_bus_cs() failed, using default environment
Loading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 **
In: serial@5000000 Out: serial@5000000 Err: serial@5000000
Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1: usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110
Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 15193.5 MB = 14.8 GB (31116288 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot/boot.scr
3636 bytes read in 1 ms (3.5 MiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from usb
205 bytes read in 1 ms (200.2 KiB/s)
Failed to load '/boot/dtb/allwinner/sun50i-h618-orangepi-zero3.dtb' libfdt fdt_check_header(): FDT_ERR_BADMAGIC
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command. Aborting!
4203 bytes read in 4 ms (1 MiB/s)
Applying kernel provided DT fixup script (sun50i-h616-fixup.scr) ## Executing script at 45000000
7088139 bytes read in 325 ms (20.8 MiB/s)
9419107 bytes read in 430 ms (20.9 MiB/s)
Uncompressing Kernel Image
Moving Image from 0x40080000 to 0x40200000, end=41800000 ## Loading init Ramdisk from Legacy Image at 4ff00000 ...
Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
ERROR: Did not find a cmdline Flattened Device Tree
Quoted 131 lines · Andre Przywara
On Sat, 25 Nov 2023 20:43:12 +0300
Mikhail Kalashnikov<[email protected]> wrote:Hi Mikhail,
Quoted 4 lines
Hi Andre!
Thanks for your patches. I started checking and noticed that USB storage was not working:Quoted 9 lines
=> usb reset
resetting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... 1 USB Device(s) found scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> usb storage
No storage devices, perhaps not 'usb start'ed..?Ah, thanks for the report, seems I didn't even test this!
So digging around I figured it's working in Linux, and it's the right USB port, but we are missing the VBUS power switch, which is a GPIO controlled regulator. There are pending patches to pick this from the devicetree[1], but we are not there yet, so we need:CONFIG_USB1_VBUS_PIN="PC16"
in the defconfig, for now. I will update the file. The same is actually missing from the OrangePi Zero2 defconfig, I will send a patch ASAP.Quoted 8 lines
Otherwise my OpiZero3 (4GB) board looks working.
Ethernet works with my 10 Mbps usb-dongle.sf probe detect spi nor flash:
=> sf probe
SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiBQuoted 4 lines
Loading the kernel and running the operating system (from microsd) also without problems.
Tested-by Mikhail Kalashnikov<[email protected]>Great, thanks for the tag!
Cheers,
AndreQuoted 86 lines · Andre Przywara
Quoted 85 lines
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the
Makefileto actually build the .dtb.The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
Signed-off-by Andre Przywara<[email protected]>--- arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+)create mode 100644 configs/orangepi_zero3_defconfig
arch/arm/dts/Makefile +1
-0@@ -835,6 +835,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ sun50i-h616-orangepi-zero2.dtb \ + sun50i-h618-orangepi-zero3.dtb \ sun50i-h616-x96-mate.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \board/sunxi/MAINTAINERS +5
-0@@ -455,6 +455,11 @@ M: Jernej Skrabec<[email protected]> S: Maintained F: configs/orangepi_zero2_defconfig +ORANGEPI ZERO 3 BOARD +M: Andre Przywara<[email protected]> +S: Maintained +F: configs/orangepi_zero3_defconfig + ORANGEPI PC 2 BOARD M: Andre Przywara<[email protected]> S: Maintainedconfigs/orangepi_zero3_defconfig new file +30
-0@@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e +CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 +CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 +CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR4=y +CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_SPI_FLASH_ZBIT=y +CONFIG_PHY_MOTORCOMM=y +CONFIG_SUN8I_EMAC=y +CONFIG_AXP313_POWER=y +CONFIG_SPI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
On Sat, 25 Nov 2023 20:27:05 -0800
Stephen Graf <[email protected]> wrote:
Hi Stephen,
Quoted 2 lines
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110".
This is a normal, though admittedly confusing message if no SD card is inserted. The code tries to (unconditionally) access the SD card, and sees that no card is there, the missing respond to the voltage select command is just the first real proof of this.
Quoted 6 lines
I am not sure of the details of the boot.cmd. The output below came from
the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.I was able to install u-boot to the SPI flash memory and there is a warning message from that also: " Loading Environment from SPIFlash...
jedec_spi_norflash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning -spi_flash_probe_bus_cs()failed, using default environment"
So for a start there is no environment on the SPI flash yet, so it wouldn't do anything. But the "unrecognised JEDEC id bytes" message doesn't sound right. Can you dig into this? Do you have patch 1/3 applied, which tells U-Boot about 0x5e meaning zBIT?
Quoted 105 lines
Thank you for your advice on getting something to boot. None of the Debian installer images were suitable. Even SID was at 6.1. I built the latest Linux 6.6.2 and wrestled with the rootfs before I got it running. I built the tested u-boot with this system, as a test of system stability.
defconfig used + emac patches
CONFIG_ARM=yCONFIG_ARCH_SUNXI=yCONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3"CONFIG_SPL=yCONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0eCONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0eCONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeeeCONFIG_DRAM_SUN50I_H616_TPR6=0x44000000CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100fCONFIG_MACH_SUN50I_H616=yCONFIG_SUNXI_DRAM_H616_LPDDR4=y
#CONFIG_DRAM_CLK=792CONFIG_USB1_VBUS_PIN="PC16"
#CONFIG_R_I2C_ENABLE=yCONFIG_SPL_SPI_SUNXI=y
#CONFIG_SYS_MALLOC_CLEAR_ON_INITis not setCONFIG_SPL_I2C=yCONFIG_SPL_SYS_I2C_LEGACY=yCONFIG_SYS_I2C_MVTWSI=yCONFIG_SYS_I2C_SLAVE=0x7fCONFIG_SYS_I2C_SPEED=400000CONFIG_SPI_FLASH_ZBIT=yCONFIG_PHY_MOTORCOMM=yCONFIG_SUN8I_EMAC=yCONFIG_AXP313_POWER=yCONFIG_SPI=yCONFIG_USB_EHCI_HCD=yCONFIG_USB_OHCI_HCD=yCONFIG_USB_MUSB_GADGET=yConsole Output:
U-Boot 2024.01-rc3-00009-g9e53e45292-dirty (Nov 25 2023 - 18:32:16 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiB Core: 57 devices, 25 uclasses, devicetree: separate WDT: Not starting watchdog@30090a0 MMC: mmc@4020000: 0Loading Environment from SPIFlash...
jedec_spi_norflash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning -spi_flash_probe_bus_cs()failed, using default environmentLoading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 **
In: serial@5000000 Out: serial@5000000 Err: serial@5000000Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1:usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 15193.5 MB = 14.8 GB (31116288 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script/boot/boot.scr
3636 bytes read in 1 ms (3.5 MiB/s)
## Executing script at4fc00000
U-boot loaded from SD
Boot script loaded from usb
205 bytes read in 1 ms (200.2 KiB/s)
Failed to load '/boot/dtb/allwinner/sun50i-h618-orangepi-zero3.dtb' libfdtfdt_check_header():FDT_ERR_BADMAGIC
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command. Aborting!
4203 bytes read in 4 ms (1 MiB/s)
Applying kernel provided DT fixup script (sun50i-h616-fixup.scr) ## Executing script at 45000000
7088139 bytes read in 325 ms (20.8 MiB/s)
9419107 bytes read in 430 ms (20.9 MiB/s)
Uncompressing Kernel Image
Moving Image from0x40080000to0x40200000, end=41800000 ## Loading init Ramdisk from Legacy Image at4ff00000...
Quoted 7 lines
Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OKERROR: Did not find a cmdline Flattened Device Tree
OK, so this is because you don't have the OPi Zero3 DTB on your image. And this is frankly not needed, because U-Boot carries this very DTB already.
In general this is some old school boot sequence, with a uImage wrapped initrd and the DTB loaded from disk. The wrapped initrd is mostly an small annoyance from a developers point of view, so this is fine.
But can you tweak the boot script to use "$fdtcontroladdr", instead of trying load a DTB from "disk"?
So remove (or ignore) the "load .... $fdt_addr_r ..." line, and change the booti command to use "$fdtcontroladdr" instead of "$fdt_addr_r". That should be all you need.
Good luck!
Cheers,
Andre
Quoted 132 lines · Andre Przywara
Quoted 131 lines
On Sat, 25 Nov 2023 20:43:12 +0300
Mikhail Kalashnikov<[email protected]> wrote:Hi Mikhail,
Quoted 4 lines
Hi Andre!
Thanks for your patches. I started checking and noticed that USB storage was not working:Quoted 9 lines
=> usb reset
resetting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... 1 USB Device(s) found scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> usb storage
No storage devices, perhaps not 'usb start'ed..?Ah, thanks for the report, seems I didn't even test this!
So digging around I figured it's working in Linux, and it's the right USB port, but we are missing the VBUS power switch, which is a GPIO controlled regulator. There are pending patches to pick this from the devicetree[1], but we are not there yet, so we need:CONFIG_USB1_VBUS_PIN="PC16"
in the defconfig, for now. I will update the file. The same is actually missing from the OrangePi Zero2 defconfig, I will send a patch ASAP.Quoted 8 lines
Otherwise my OpiZero3 (4GB) board looks working.
Ethernet works with my 10 Mbps usb-dongle.sf probe detect spi nor flash:
=> sf probe
SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiBQuoted 4 lines
Loading the kernel and running the operating system (from microsd) also without problems.
Tested-by Mikhail Kalashnikov<[email protected]>Great, thanks for the tag!
Cheers,
AndreQuoted 86 lines · Andre Przywara
Quoted 85 lines
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the
Makefileto actually build the .dtb.The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
Signed-off-by Andre Przywara<[email protected]>--- arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+)create mode 100644 configs/orangepi_zero3_defconfig
arch/arm/dts/Makefile +1
-0@@ -835,6 +835,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ sun50i-h616-orangepi-zero2.dtb \ + sun50i-h618-orangepi-zero3.dtb \ sun50i-h616-x96-mate.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \board/sunxi/MAINTAINERS +5
-0@@ -455,6 +455,11 @@ M: Jernej Skrabec<[email protected]> S: Maintained F: configs/orangepi_zero2_defconfig +ORANGEPI ZERO 3 BOARD +M: Andre Przywara<[email protected]> +S: Maintained +F: configs/orangepi_zero3_defconfig + ORANGEPI PC 2 BOARD M: Andre Przywara<[email protected]> S: Maintainedconfigs/orangepi_zero3_defconfig new file +30
-0@@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e +CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 +CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 +CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR4=y +CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_SPI_FLASH_ZBIT=y +CONFIG_PHY_MOTORCOMM=y +CONFIG_SUN8I_EMAC=y +CONFIG_AXP313_POWER=y +CONFIG_SPI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
Yes I forgot about the zBIT patch. With this patch also included I built and retested u-boot loaded from SPI flash. The two warning/error messages disappeared and the flash worked properly and booted from a USB device.
There was one message that I did not understand:
"Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment"
I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0
Console log of boot:
U-Boot SPL 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800)
DRAM: 1024 MiB
Trying to boot from sunxi SPI
NOTICE: BL31: v2.10.0 (debug):v2.10.0 NOTICE: BL31: Built : 18:07:18, Nov 23 2023 NOTICE: BL31: Detected Allwinner H616 SoC (1823) NOTICE: BL31: Found U-Boot DTB at 0x4a0b2798, model: OrangePi Zero3 INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP305 on RSB ERROR: RSB: set run-time address: 0x10003 INFO: Could not init RSB: -65539 INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for erratum 855873 was applied INFO: BL31: cortex_a53: CPU workaround for erratum 1530924 was applied INFO: PSCI: Suspend is unavailable INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9 INFO: Changed devicetree.
U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiB Core: 57 devices, 25 uclasses, devicetree: separate WDT: Not starting watchdog@30090a0 MMC: mmc@4020000: 0
Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
Loading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 **
In: serial@5000000 Out: serial@5000000 Err: serial@5000000
Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1: usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110
Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 3828.0 MB = 3.7 GB (7839744 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 1 ms (1.5 MiB/s)
## Executing script at 4fc00000
Mainline u-boot / new-style environment detected.
This installer medium does not contain a suitable device-tree file for this system (allwinner/sun50i-h618-orangepi-zero3.dtb). Aborting boot process. SCRIPT FAILED: continuing...
Found U-Boot script /boot/boot.scr
621 bytes read in 2 ms (302.7 KiB/s)
## Executing script at 4fc00000
19472 bytes read in 3 ms (6.2 MiB/s)
Working FDT set to 4fa00000
7088139 bytes read in 326 ms (20.7 MiB/s)
22491144 bytes read in 1031 ms (20.8 MiB/s)
Moving Image from 0x40080000 to 0x40200000, end=41800000
## Loading init Ramdisk from Legacy Image at 4ff00000 ...
Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
Booting using the fdt blob at 0x4fa00000
Working FDT set to 4fa00000
Loading Ramdisk to 4993d000, end 49fff7cb ... OK
Loading Device Tree to 00000000498cf000, end 000000004993cfff ... OK
Working FDT set to 498cf000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.6.2 (orangepi@orangepizero3) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Nov 25 18:37:47 UTC 2023
Quoted 25 lines · Andre Przywara
On Sat, 25 Nov 2023 20:27:05 -0800
Stephen Graf <[email protected]> wrote:Hi Stephen,
Quoted 2 lines
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110".
This is a normal, though admittedly confusing message if no SD card is inserted. The code tries to (unconditionally) access the SD card, and sees that no card is there, the missing respond to the voltage select command is just the first real proof of this.
Quoted 6 lines
I am not sure of the details of the boot.cmd. The output below came from
the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.I was able to install u-boot to the SPI flash memory and there is a warning message from that also: " Loading Environment from SPIFlash...
jedec_spi_norflash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning -spi_flash_probe_bus_cs()failed, using default environment"So for a start there is no environment on the SPI flash yet, so it wouldn't do anything. But the "unrecognised JEDEC id bytes" message doesn't sound right. Can you dig into this? Do you have patch 1/3 applied, which tells U-Boot about
0x5emeaning zBIT?
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
Since the last test I rebuilt u-boot without the
"CONFIG_DRAM_CLK=792" in the defconfig and got the wrong DRAM size problem (showing 2G instead of 1G). I had to do a power down/up to see this. Are you planning to add this parameter to your patch?
U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 12:25:33 -0800) Allwin ner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 2 GiB
Quoted 150 lines · Stephen Graf
Yes I forgot about the zBIT patch. With this patch also included I built and retested u-boot loaded from SPI flash. The two warning/error messages disappeared and the flash worked properly and booted from a USB device.
There was one message that I did not understand:
"Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment"I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0Console log of boot:
U-Boot SPL 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800)
DRAM: 1024 MiB
Trying to boot from sunxi SPI
NOTICE: BL31: v2.10.0 (debug):v2.10.0
NOTICE: BL31: Built : 18:07:18, Nov 23 2023
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at0x4a0b2798, model: OrangePi Zero3 INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP305 on RSB
ERROR: RSB: set run-time address:0x10003
INFO: Could not init RSB: -65539
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31:cortex_a53: CPU workaround for erratum 855873 was applied INFO: BL31:cortex_a53: CPU workaround for erratum 1530924 was applied INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address =0x4a000000
INFO: SPSR =0x3c9
INFO: Changed devicetree.U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero3
DRAM: 1 GiB
Core: 57 devices, 25 uclasses, devicetree: separate
WDT: Not starting watchdog@30090a0
MMC: mmc@4020000: 0
Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environmentLoading Environment from FAT... Card did not respond to voltage select! : -110 ** Bad device specification mmc 0 **
In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1:usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 3828.0 MB = 3.7 GB (7839744 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 1 ms (1.5 MiB/s)
## Executing script at4fc00000
Mainline u-boot / new-style environment detected.
This installer medium does not contain a suitable device-tree file for this system (allwinner/sun50i-h618-orangepi-zero3.dtb). Aborting boot process. SCRIPT FAILED: continuing...
Found U-Boot script/boot/boot.scr
621 bytes read in 2 ms (302.7 KiB/s)
## Executing script at4fc00000
19472 bytes read in 3 ms (6.2 MiB/s)
Working FDT set to4fa00000
7088139 bytes read in 326 ms (20.7 MiB/s)
22491144 bytes read in 1031 ms (20.8 MiB/s)
Moving Image from0x40080000to0x40200000, end=41800000
## Loading init Ramdisk from Legacy Image at4ff00000...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at4fa00000
Booting using the fdt blob at0x4fa00000
Working FDT set to4fa00000
Loading Ramdisk to4993d000, end49fff7cb... OK
Loading Device Tree to00000000498cf000, end000000004993cfff... OK
Working FDT set to498cf000Starting kernel ...
[ 0.000000] Booting Linux on physical CPU
0x0000000000[0x410fd034]
[ 0.000000] Linux version 6.6.2 (orangepi@orangepizero3) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Nov 25 18:37:47 UTC 2023Quoted 25 lines · Andre Przywara
On Sat, 25 Nov 2023 20:27:05 -0800
Stephen Graf <[email protected]> wrote:Hi Stephen,
Quoted 2 lines
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110".
This is a normal, though admittedly confusing message if no SD card is inserted. The code tries to (unconditionally) access the SD card, and sees that no card is there, the missing respond to the voltage select command is just the first real proof of this.
Quoted 6 lines
I am not sure of the details of the boot.cmd. The output below came from
the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.I was able to install u-boot to the SPI flash memory and there is a warning message from that also: " Loading Environment from SPIFlash...
jedec_spi_norflash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning -spi_flash_probe_bus_cs()failed, using default environment"So for a start there is no environment on the SPI flash yet, so it wouldn't do anything. But the "unrecognised JEDEC id bytes" message doesn't sound right. Can you dig into this? Do you have patch 1/3 applied, which tells U-Boot about
0x5emeaning zBIT?
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
On Mon, 27 Nov 2023 14:31:19 -0800
Stephen Graf <[email protected]> wrote:
Hi,
Quoted 4 lines
Since the last test I rebuilt u-boot without the "
CONFIG_DRAM_CLK=792" in the defconfig and got the wrong DRAM size problem (showing 2G instead of 1G). I had to do a power down/up to see this. Are you planning to add this parameter to your patch?
This symptom is pretty surely not directly related to the DRAM frequency, it's caused by a missing barrier or delay *somewhere*. People report that this is fixed by adding another "dsb();" at the beginning of the mctl_mem_matches() function, but I don't have a good explanation why exactly there, and would like to avoid submitting patches that "just seem to work (TM)".
If I find some time, I will try to setup some automated environment where I can run some experiments with different barrier locations. I can offer some rationale for putting it at the end of the function(s) that call mctl_mem_matches(), so hope that this fixes it.
Cheers,
Andre
Quoted 181 lines
U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 12:25:33
-0800) Allwin ner
TechnologyCPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 2 GiBQuoted 170 lines · Stephen Graf
Yes I forgot about the zBIT patch. With this patch also included I built and retested u-boot loaded from SPI flash. The two warning/error messages disappeared and the flash worked properly and booted from a USB device.
There was one message that I did not understand:
"Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment"I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0Console log of boot:
U-Boot SPL 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800)
DRAM: 1024 MiB
Trying to boot from sunxi SPI
NOTICE: BL31: v2.10.0 (debug):v2.10.0
NOTICE: BL31: Built : 18:07:18, Nov 23 2023
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at0x4a0b2798, model: OrangePi Zero3 INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP305 on RSB
ERROR: RSB: set run-time address:0x10003
INFO: Could not init RSB: -65539
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31:cortex_a53: CPU workaround for erratum 855873 was applied INFO: BL31:cortex_a53: CPU workaround for erratum 1530924 was applied INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address =0x4a000000
INFO: SPSR =0x3c9
INFO: Changed devicetree.U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero3
DRAM: 1 GiB
Core: 57 devices, 25 uclasses, devicetree: separate
WDT: Not starting watchdog@30090a0
MMC: mmc@4020000: 0
Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environmentLoading Environment from FAT... Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1:usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 3828.0 MB = 3.7 GB (7839744 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 1 ms (1.5 MiB/s)
## Executing script at4fc00000
Mainline u-boot / new-style environment detected.
This installer medium does not contain a suitable device-tree file for this system (allwinner/sun50i-h618-orangepi-zero3.dtb). Aborting boot process.
SCRIPT FAILED: continuing...
Found U-Boot script/boot/boot.scr
621 bytes read in 2 ms (302.7 KiB/s)
## Executing script at4fc00000
19472 bytes read in 3 ms (6.2 MiB/s)
Working FDT set to4fa00000
7088139 bytes read in 326 ms (20.7 MiB/s)
22491144 bytes read in 1031 ms (20.8 MiB/s)
Moving Image from0x40080000to0x40200000, end=41800000
## Loading init Ramdisk from Legacy Image at4ff00000...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at4fa00000
Booting using the fdt blob at0x4fa00000
Working FDT set to4fa00000
Loading Ramdisk to4993d000, end49fff7cb... OK
Loading Device Tree to00000000498cf000, end000000004993cfff... OK
Working FDT set to498cf000Starting kernel ...
[ 0.000000] Booting Linux on physical CPU
0x0000000000[0x410fd034] [ 0.000000] Linux version 6.6.2 (orangepi@orangepizero3) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Nov 25 18:37:47 UTC 2023Quoted 30 lines · Andre Przywara
On Sat, 25 Nov 2023 20:27:05 -0800
Stephen Graf <[email protected]> wrote:Hi Stephen,
Quoted 3 lines
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110".
This is a normal, though admittedly confusing message if no SD card is inserted. The code tries to (unconditionally) access the SD card, and sees that no card is there, the missing respond to the voltage select command is just the first real proof of this.
Quoted 10 lines
I am not sure of the details of the boot.cmd. The output below came from the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.
I was able to install u-boot to the SPI flash memory and there is a warning message from that also: "
Loading Environment from SPIFlash...jedec_spi_norflash@0:
unrecognized JEDEC id bytes: 5e, 40, 18
*** Warning -spi_flash_probe_bus_cs()failed, using default environment"So for a start there is no environment on the SPI flash yet, so it wouldn't do anything. But the "unrecognised JEDEC id bytes" message doesn't sound right. Can you dig into this? Do you have patch 1/3 applied, which tells U-Boot about
0x5emeaning zBIT?
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
I got the initial defconfig that I started testing with from:
https://gist.github.com/iuncuim/2150b7a5317700314393665260ca628e
which has CONFIG_DRAM_CLK=792.
Just a few hours ago, when I was testing without this parameter, my system misbehaved and refused to reboot. The file system was corrupted and I had to reinstall the rootfs to get it going again. I put the u-boot with the CONFIG_DRAM_CLK=792 back on it.
I will retest the system by building u-boot which is what I was doing when it crashed.
Quoted 207 lines · Andre Przywara
On Mon, 27 Nov 2023 14:31:19 -0800
Stephen Graf <[email protected]> wrote:Hi,
Quoted 4 lines
Since the last test I rebuilt u-boot without the "
CONFIG_DRAM_CLK=792" in the defconfig and got the wrong DRAM size problem (showing 2G instead of 1G). I had to do a power down/up to see this. Are you planning to add this parameter to your patch?This symptom is pretty surely not directly related to the DRAM frequency, it's caused by a missing barrier or delay *somewhere*. People report that this is fixed by adding another "
dsb();" at the beginning of themctl_mem_matches()function, but I don't have a good explanation why exactly there, and would like to avoid submitting patches that "just seem to work (TM)".If I find some time, I will try to setup some automated environment where I can run some experiments with different barrier locations. I can offer some rationale for putting it at the end of the function(s) that call
mctl_mem_matches(), so hope that this fixes it.Cheers,
AndreQuoted 181 lines
U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 12:25:33
-0800) Allwin ner
TechnologyCPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 2 GiBQuoted 170 lines · Stephen Graf
Yes I forgot about the zBIT patch. With this patch also included I built and retested u-boot loaded from SPI flash. The two warning/error messages disappeared and the flash worked properly and booted from a USB device.
There was one message that I did not understand:
"Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment"I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0Console log of boot:
U-Boot SPL 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800)
DRAM: 1024 MiB
Trying to boot from sunxi SPI
NOTICE: BL31: v2.10.0 (debug):v2.10.0
NOTICE: BL31: Built : 18:07:18, Nov 23 2023
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at0x4a0b2798, model: OrangePi Zero3 INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP305 on RSB
ERROR: RSB: set run-time address:0x10003
INFO: Could not init RSB: -65539
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31:cortex_a53: CPU workaround for erratum 855873 was applied INFO: BL31:cortex_a53: CPU workaround for erratum 1530924 was applied INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address =0x4a000000
INFO: SPSR =0x3c9
INFO: Changed devicetree.U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero3
DRAM: 1 GiB
Core: 57 devices, 25 uclasses, devicetree: separate
WDT: Not starting watchdog@30090a0
MMC: mmc@4020000: 0
Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environmentLoading Environment from FAT... Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1:usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 3828.0 MB = 3.7 GB (7839744 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 1 ms (1.5 MiB/s)
## Executing script at4fc00000
Mainline u-boot / new-style environment detected.
This installer medium does not contain a suitable device-tree file for this system (allwinner/sun50i-h618-orangepi-zero3.dtb). Aborting boot process.
SCRIPT FAILED: continuing...
Found U-Boot script/boot/boot.scr
621 bytes read in 2 ms (302.7 KiB/s)
## Executing script at4fc00000
19472 bytes read in 3 ms (6.2 MiB/s)
Working FDT set to4fa00000
7088139 bytes read in 326 ms (20.7 MiB/s)
22491144 bytes read in 1031 ms (20.8 MiB/s)
Moving Image from0x40080000to0x40200000, end=41800000
## Loading init Ramdisk from Legacy Image at4ff00000...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at4fa00000
Booting using the fdt blob at0x4fa00000
Working FDT set to4fa00000
Loading Ramdisk to4993d000, end49fff7cb... OK
Loading Device Tree to00000000498cf000, end000000004993cfff... OK
Working FDT set to498cf000Starting kernel ...
[ 0.000000] Booting Linux on physical CPU
0x0000000000[0x410fd034] [ 0.000000] Linux version 6.6.2 (orangepi@orangepizero3) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Nov 25 18:37:47 UTC 2023Quoted 30 lines · Andre Przywara
On Sat, 25 Nov 2023 20:27:05 -0800
Stephen Graf <[email protected]> wrote:Hi Stephen,
Quoted 3 lines
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110".
This is a normal, though admittedly confusing message if no SD card is inserted. The code tries to (unconditionally) access the SD card, and sees that no card is there, the missing respond to the voltage select command is just the first real proof of this.
Quoted 10 lines
I am not sure of the details of the boot.cmd. The output below came from the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.
I was able to install u-boot to the SPI flash memory and there is a warning message from that also: "
Loading Environment from SPIFlash...jedec_spi_norflash@0:
unrecognized JEDEC id bytes: 5e, 40, 18
*** Warning -spi_flash_probe_bus_cs()failed, using default environment"So for a start there is no environment on the SPI flash yet, so it wouldn't do anything. But the "unrecognised JEDEC id bytes" message doesn't sound right. Can you dig into this? Do you have patch 1/3 applied, which tells U-Boot about
0x5emeaning zBIT?
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
In reply to Andre PrzywaraI did some digging into the orangepi SDK and it sort of looks like the zero3 is set up for dram_clk = 792. I use their image as a fallback and it has been stable (built linux kernel and set up debian rootfs).
from https://github.com/orangepi-xunlong/orangepi-build.git
external/packages/pack-uboot/sun50iw9/bin/dts/orangepizero3-u-boot-legacy.dts:
dram_type = <0x8>;
external/packages/pack-uboot/sun50iw9/bin/sys_config/sys_config_orangepizero3.fex
[dram_para]dram_clk = 792dram_type = 8dram_dx_odt = 0x07070707dram_dx_dri = 0x0e0e0e0edram_ca_dri = 0x0e0edram_odt_en = 0xaaaaeeeedram_para1 = 0x30fadram_para2 = 0x0000dram_mr0 = 0x0dram_mr1 = 0x34dram_mr2 = 0x1bdram_mr3 = 0x33dram_mr4 = 0x3dram_mr5 = 0x0dram_mr6 = 0x0dram_mr11 = 0x4dram_mr12 = 0x72dram_mr13 = 0x0dram_mr14 = 0x9dram_mr16 = 0x0dram_mr17 = 0x0dram_mr22 = 0x24dram_tpr0 = 0x0dram_tpr1 = 0x0dram_tpr2 = 0x0dram_tpr3 = 0x0dram_tpr6 = 0x35808080dram_tpr10 = 0x402f6663dram_tpr11 = 0x36363535dram_tpr12 = 0x10101110dram_tpr13 = 0x2080C60
[dram_para16]dram_clk = 792dram_type = 8dram_dx_odt = 0x07070707dram_dx_dri = 0x0e0e0e0edram_ca_dri = 0x0e0edram_odt_en = 0xaaaaeeeedram_para1 = 0x30fadram_para2 = 0x0000dram_mr0 = 0x0dram_mr1 = 0x34dram_mr2 = 0x1bdram_mr3 = 0x33dram_mr4 = 0x3dram_mr5 = 0x0dram_mr6 = 0x0dram_mr11 = 0x4dram_mr12 = 0x72dram_mr13 = 0x0dram_mr14 = 0x9dram_mr16 = 0x0dram_mr17 = 0x0dram_mr22 = 0x24dram_tpr0 = 0x0dram_tpr1 = 0x0dram_tpr2 = 0x0dram_tpr3 = 0x0dram_tpr6 = 0x35808080dram_tpr10 = 0x402f6663dram_tpr11 = 0x36363535dram_tpr12 = 0x10101110dram_tpr13 = 0x2080C60
Quoted 207 lines · Andre Przywara
On Mon, 27 Nov 2023 14:31:19 -0800
Stephen Graf <[email protected]> wrote:Hi,
Quoted 4 lines
Since the last test I rebuilt u-boot without the "
CONFIG_DRAM_CLK=792" in the defconfig and got the wrong DRAM size problem (showing 2G instead of 1G). I had to do a power down/up to see this. Are you planning to add this parameter to your patch?This symptom is pretty surely not directly related to the DRAM frequency, it's caused by a missing barrier or delay *somewhere*. People report that this is fixed by adding another "
dsb();" at the beginning of themctl_mem_matches()function, but I don't have a good explanation why exactly there, and would like to avoid submitting patches that "just seem to work (TM)".If I find some time, I will try to setup some automated environment where I can run some experiments with different barrier locations. I can offer some rationale for putting it at the end of the function(s) that call
mctl_mem_matches(), so hope that this fixes it.Cheers,
AndreQuoted 181 lines
U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 12:25:33
-0800) Allwin ner
TechnologyCPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 2 GiBQuoted 170 lines · Stephen Graf
Yes I forgot about the zBIT patch. With this patch also included I built and retested u-boot loaded from SPI flash. The two warning/error messages disappeared and the flash worked properly and booted from a USB device.
There was one message that I did not understand:
"Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment"I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0Console log of boot:
U-Boot SPL 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800)
DRAM: 1024 MiB
Trying to boot from sunxi SPI
NOTICE: BL31: v2.10.0 (debug):v2.10.0
NOTICE: BL31: Built : 18:07:18, Nov 23 2023
NOTICE: BL31: Detected Allwinner H616 SoC (1823)
NOTICE: BL31: Found U-Boot DTB at0x4a0b2798, model: OrangePi Zero3 INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP305 on RSB
ERROR: RSB: set run-time address:0x10003
INFO: Could not init RSB: -65539
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31:cortex_a53: CPU workaround for erratum 855873 was applied INFO: BL31:cortex_a53: CPU workaround for erratum 1530924 was applied INFO: PSCI: Suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address =0x4a000000
INFO: SPSR =0x3c9
INFO: Changed devicetree.U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero3
DRAM: 1 GiB
Core: 57 devices, 25 uclasses, devicetree: separate
WDT: Not starting watchdog@30090a0
MMC: mmc@4020000: 0
Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environmentLoading Environment from FAT... Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in
MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1:usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 3828.0 MB = 3.7 GB (7839744 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 1 ms (1.5 MiB/s)
## Executing script at4fc00000
Mainline u-boot / new-style environment detected.
This installer medium does not contain a suitable device-tree file for this system (allwinner/sun50i-h618-orangepi-zero3.dtb). Aborting boot process.
SCRIPT FAILED: continuing...
Found U-Boot script/boot/boot.scr
621 bytes read in 2 ms (302.7 KiB/s)
## Executing script at4fc00000
19472 bytes read in 3 ms (6.2 MiB/s)
Working FDT set to4fa00000
7088139 bytes read in 326 ms (20.7 MiB/s)
22491144 bytes read in 1031 ms (20.8 MiB/s)
Moving Image from0x40080000to0x40200000, end=41800000
## Loading init Ramdisk from Legacy Image at4ff00000...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at4fa00000
Booting using the fdt blob at0x4fa00000
Working FDT set to4fa00000
Loading Ramdisk to4993d000, end49fff7cb... OK
Loading Device Tree to00000000498cf000, end000000004993cfff... OK
Working FDT set to498cf000Starting kernel ...
[ 0.000000] Booting Linux on physical CPU
0x0000000000[0x410fd034] [ 0.000000] Linux version 6.6.2 (orangepi@orangepizero3) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Nov 25 18:37:47 UTC 2023Quoted 30 lines · Andre Przywara
On Sat, 25 Nov 2023 20:27:05 -0800
Stephen Graf <[email protected]> wrote:Hi Stephen,
Quoted 3 lines
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110".
This is a normal, though admittedly confusing message if no SD card is inserted. The code tries to (unconditionally) access the SD card, and sees that no card is there, the missing respond to the voltage select command is just the first real proof of this.
Quoted 10 lines
I am not sure of the details of the boot.cmd. The output below came from the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.
I was able to install u-boot to the SPI flash memory and there is a warning message from that also: "
Loading Environment from SPIFlash...jedec_spi_norflash@0:
unrecognized JEDEC id bytes: 5e, 40, 18
*** Warning -spi_flash_probe_bus_cs()failed, using default environment"So for a start there is no environment on the SPI flash yet, so it wouldn't do anything. But the "unrecognised JEDEC id bytes" message doesn't sound right. Can you dig into this? Do you have patch 1/3 applied, which tells U-Boot about
0x5emeaning zBIT?
mdt_debug write
In reply to Andre PrzywaraBelow is the consol log from trying to use mtd_debug write. It returned immediately with a strange success message.
root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success
I then used the cat command to write to the SPI flash which took a few seconds to execute:
root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0
Quoted 18 lines
Quoted 18 lines
Quoted 18 lines
I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success
Re: mdt_debug write
Hi Stephen,
Quoted 5 lines · Stephen Graf
Below is the consol log from trying to use
mtd_debugwrite. It returned immediately with a strange success message.root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success
interesting, I was under the impression that "mtd_debug write" would be the way to write to flash. In hindsight, the "debug" in that name should have probably put me off. Anyway, "cat" is probably not a good choice, "dd" is better, but it looks like "flashcp" (also part of mtdutils) is the go-to tool, since it does the required erasing automatically and also reportedly does some error detection. Can you please test this?
# flashcp u-boot-sunxi-with-spl.bin /dev/mtd0 I would test this on my end ASAP as well.
Do you feel like sending a patch to the U-Boot documentation to get this changed then?
Thanks,
Andre
Quoted 25 lines
I then used the cat command to write to the SPI flash which took a few seconds to execute:
root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0Quoted 18 lines
Quoted 18 lines
Quoted 18 lines
I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success
Re: mdt_debug write
Thank you for the update Andre.
The flashcp worked. I rebooted without an SD card and the new u-boot started properly.
Now as to making a patch file, I will give it a try. Keep in mind that when I started my working career the concept of patching was to shuffle a deck of IBM 80 column punched cards.
Console output:
root@orangepizero3:~# flashcp -v /home/sysadmin/u-boot-sunxi-with-spl.bin_with_792_clk /dev/mtd0 Erasing blocks: 206/206 (100%) Writing data: 822k/822k (100%) Verifying data: 822k/822k (100%) root@orangepizero3:~#
Quoted 18 lines · Andre Przywara
Hi Stephen,
Quoted 5 lines · Stephen Graf
Below is the consol log from trying to use
mtd_debugwrite. It returned immediately with a strange success message.root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Successinteresting, I was under the impression that "
mtd_debugwrite" would be the way to write to flash. In hindsight, the "debug" in that name should have probably put me off. Anyway, "cat" is probably not a good choice, "dd" is better, but it looks like "flashcp" (also part of mtdutils) is the go-to tool, since it does the required erasing automatically and also reportedly does some error detection. Can you please test this?# flashcp u-boot-sunxi-with-spl.bin /dev/mtd0 I would test this on my end ASAP as well.Do you feel like sending a patch to the U-Boot documentation to get this changed then?
Thanks,
Andre
Re: mdt_debug write
In reply to Andre PrzywaraIs the attached patch file going in the right direction?
Quoted 9 lines · Andre Przywara
Hi Stephen,
Quoted 5 lines · Stephen Graf
Below is the console log from trying to use
mtd_debugwrite. It returned immediately with a strange success message.root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success
Quoted 9 lines
interesting, I was under the impression that "
mtd_debugwrite" would be the way to write to flash. In hindsight, the "debug" in that name should have probably put me off. Anyway, "cat" is probably not a good choice, "dd" is better, but it looks like "flashcp" (also part of mtdutils) is the go-to tool, since it does the required erasing automatically and also reportedly does some error detection. Can you please test this?# flashcp u-boot-sunxi-with-spl.bin /dev/mtd0 I would test this on my end ASAP as well.Do you feel like sending a patch to the U-Boot documentation to get this changed then?
Thanks,
Andre
board/allwinner/sunxi.rst_updated 2023-11-29 16:48:03.682352328 -0800 renamed from board/allwinner/sunxi.rst 2023-11-28 21:31:06.844607403 -0800 +1 -2
@@ -251,8 +251,7 @@ # apt-get install mtd-utils # mtdinfo - # mtd_debug erase /dev/mtdX 0 0xf0000 - # mtd_debug write /dev/mtdX 0 0xf0000 u-boot-sunxi-with-spl.bin + # flashcp -v u-boot-sunxi-with-spl.bin /dev/mtdX ``/dev/mtdX`` needs to be replaced with the respective device name, as listed in the output of ``mtdinfo``.
Re: mdt_debug write
Hi Stephen,
Quoted 1 line · Stephen Graf
Is the attached patch file going in the right direction?
yes, thanks, the change itself looks alright, but it needs to be:
- in a separate email, with a descriptive subject, prefixed by [PATCH]
- have the diff inline, not as an attachment (to allow easy commenting in an email thread)
- have a Signed-off-by: tag with your name and email address. This is to signify that the change is an original one made by you and you are happy to submit this under the (GPL) license conditions.
- an explanation *why* this change is required (mtd_debug write being not reliable, etc)
- sent to the U-Boot list and the maintainer (me)
Look at the U-Boot mailing list (archive) for examples.
"git format-patch" creates everything in the right format (mbox), and "git send-email" will send this via an SMTP server you point it to. Or you import this into your client.
If you could try this (with the Signed-off-by being the most important change), I am happy to submit this with the next push.
Thanks,
Andre
Quoted 20 lines · Andre Przywara
Quoted 18 lines
Hi Stephen,
Quoted 5 lines · Stephen Graf
Below is the console log from trying to use
mtd_debugwrite. It returned immediately with a strange success message.root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Successinteresting, I was under the impression that "
mtd_debugwrite" would be the way to write to flash. In hindsight, the "debug" in that name should have probably put me off. Anyway, "cat" is probably not a good choice, "dd" is better, but it looks like "flashcp" (also part of mtdutils) is the go-to tool, since it does the required erasing automatically and also reportedly does some error detection. Can you please test this?# flashcp u-boot-sunxi-with-spl.bin /dev/mtd0 I would test this on my end ASAP as well.Do you feel like sending a patch to the U-Boot documentation to get this changed then?
Thanks,
Andre
PATCH 1/1 correct documentation for SPI flashing
The mtd_debug write does not work in this context. The flashcp command does work, provides both the erase and write functions and with the verbose option gives good feedback.
--- doc/board/allwinner/sunxi.rst | 3 +-- 1 file changed, 1 insertions(+), 2 deletions(-)
doc/board/allwinner/sunxi.rst +1 -2
@@ -251,8 +251,7 @@ the SPI flash content from Linux, using the `MTD utils`_:: # apt-get install mtd-utils # mtdinfo - # mtd_debug erase /dev/mtdX 0 0xf0000 - # mtd_debug write /dev/mtdX 0 0xf0000 u-boot-sunxi-with-spl.bin + # flashcp -v u-boot-sunxi-with-spl.bin /dev/mtdX ``/dev/mtdX`` needs to be replaced with the respective device name, as listed in the output of ``mtdinfo``.
---
Quoted 40 lines · Andre Przywara
Hi Stephen,
Quoted 1 line · Stephen Graf
Is the attached patch file going in the right direction?
yes, thanks, the change itself looks alright, but it needs to be:
- in a separate email, with a descriptive subject, prefixed by [PATCH]
- have the diff inline, not as an attachment (to allow easy commenting in an email thread)
- have a Signed-off-by: tag with your name and email address. This is to signify that the change is an original one made by you and you are happy to submit this under the (GPL) license conditions.
- an explanation *why* this change is required (mtd_debugwrite being not reliable, etc)
- sent to the U-Boot list and the maintainer (me)Look at the U-Boot mailing list (archive) for examples.
"git format-patch" creates everything in the right format (mbox), and "git send-email" will send this via an SMTP server you point it to. Or you import this into your client.If you could try this (with the Signed-off-by being the most important change), I am happy to submit this with the next push.
Thanks,
AndreQuoted 20 lines · Andre Przywara
Quoted 18 lines
Hi Stephen,
Quoted 5 lines · Stephen Graf
Below is the console log from trying to use
mtd_debugwrite. It returned immediately with a strange success message.root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Successinteresting, I was under the impression that "
mtd_debugwrite" would be the way to write to flash. In hindsight, the "debug" in that name should have probably put me off. Anyway, "cat" is probably not a good choice, "dd" is better, but it looks like "flashcp" (also part of mtdutils) is the go-to tool, since it does the required erasing automatically and also reportedly does some error detection. Can you please test this?# flashcp u-boot-sunxi-with-spl.bin /dev/mtd0 I would test this on my end ASAP as well.Do you feel like sending a patch to the U-Boot documentation to get this changed then?
Thanks,
Andre
Re: [PATCH 1/1] correct documentation for SPI flashing
On Fri, 1 Dec 2023 10:50:39 -0800
Stephen Graf <[email protected]> wrote:
Hi Stephen,
thanks for the patch, and you almost nailed it, some little things:
- The patch should start a new thread on the list, so do not reply to an existing discussion or (un)related patch. This avoids the patch getting buried in longish threads and helps tools like patchworks to find and process it. Also please just send the patch, and avoid any quoted text from previous discussions outside of the commit message.
- Please prefix your commit message with some context tags, in this case "sunxi: ", so that people scanning the list can ignore it if it's outside their scope of interest.
- Please limit commit messages to 75 characters per line.
$ scripts/checkpatch.pl 0001-correct_documentation_for_SPI_flashing.patch will do some checks on the patch and would report this.
Anyway, those are minor things, I will just fix them while committing.
Quoted 4 lines
The
mtd_debugwrite does not work in this context. The flashcp command does work, provides both the erase and write functions and with the verbose option gives good feedback.Signed-off-by Stephen Graf <[email protected]>
Cheers,
Andre
Quoted 62 lines
--- doc/board/allwinner/sunxi.rst | 3 +-- 1 file changed, 1 insertions(+), 2 deletions(-)doc/board/allwinner/sunxi.rst +1
-3@@ -251,8 +251,7 @@ the SPI flash content from Linux, using the `MTD utils`_:: # apt-get install mtd-utils # mtdinfo - # mtd_debug erase /dev/mtdX 0 0xf0000 - # mtd_debug write /dev/mtdX 0 0xf0000 u-boot-sunxi-with-spl.bin + # flashcp -v u-boot-sunxi-with-spl.bin /dev/mtdX ``/dev/mtdX`` needs to be replaced with the respective device name, as listed in the output of ``mtdinfo``. ---Quoted 40 lines · Andre Przywara
Hi Stephen,
Quoted 1 line · Stephen Graf
Is the attached patch file going in the right direction?
yes, thanks, the change itself looks alright, but it needs to be:
- in a separate email, with a descriptive subject, prefixed by [PATCH]
- have the diff inline, not as an attachment (to allow easy commenting in an email thread)
- have a Signed-off-by: tag with your name and email address. This is to signify that the change is an original one made by you and you are happy to submit this under the (GPL) license conditions.
- an explanation *why* this change is required (mtd_debugwrite being not reliable, etc)
- sent to the U-Boot list and the maintainer (me)Look at the U-Boot mailing list (archive) for examples.
"git format-patch" creates everything in the right format (mbox), and "git send-email" will send this via an SMTP server you point it to. Or you import this into your client.If you could try this (with the Signed-off-by being the most important change), I am happy to submit this with the next push.
Thanks,
AndreQuoted 20 lines · Andre Przywara
Quoted 18 lines
Hi Stephen,
Quoted 5 lines · Stephen Graf
Below is the console log from trying to use
mtd_debugwrite. It returned immediately with a strange success message.root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Successinteresting, I was under the impression that "
mtd_debugwrite" would be the way to write to flash. In hindsight, the "debug" in that name should have probably put me off. Anyway, "cat" is probably not a good choice, "dd" is better, but it looks like "flashcp" (also part of mtdutils) is the go-to tool, since it does the required erasing automatically and also reportedly does some error detection. Can you please test this?# flashcp u-boot-sunxi-with-spl.bin /dev/mtd0 I would test this on my end ASAP as well.Do you feel like sending a patch to the U-Boot documentation to get this changed then?
Thanks,
Andre
OrangePI Zero3 memory timing testing
In reply to Andre PrzywaraSome testing results:
With the default DRAM timing of 30x24=720, most often when my system boots it comes up with DRAM 2G, but I have a 1G system. Once in a while the boot shows 1G. When it shows 2G the linux OS also shows 2G and continuing does not make much sense.
On one boot where u-boot reported 1G the OS agreed and I ran memtester successfully.
If I build u-boot with CONFIG_DRAM_CLK=792 (33*24=792) I have never seen my system boot with anything other than DRAM 1G showing in u-boot. I ran memtester successfully and this system has been stable running linux 6.6.2.
Andre, if you can put together a few patches I can test them to see which works.
If anyone else with different variations of the Zero3 would test with the two DRAM timings and report results.
I also use the Zunlong image on occasion and it consistently shows 1G and from my poking around I think it runs at a 792 clk.
Console output with DRAM default:
U-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 22:46:39 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 2 GiB
Last login: Wed Nov 29 09:35:15 PST 2023 on ttyS0
root@orangepizero3:~# free -h
total used free shared buff/cache
available
Mem: 1.9Gi 139Mi 1.7Gi 360Ki 82Mi
1.7Gi
Swap: 0B 0B 0BU-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 22:46:39 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiB
root@orangepizero3:~# free -h
total used free shared buff/cache
available
Mem: 917Mi 137Mi 766Mi 360Ki 79Mi
780Mi
Swap: 0B 0B 0Broot@orangepizero3:~# memtester 700M 1 memtester version 4.6.0 (64-bit) Copyright (C) 2001-2020 Charles Cazabon. Licensed under the GNU General Public License version 2 (only).
pagesize is 4096
pagesizemask is 0xfffffffffffff000
want 700MB (734003200 bytes)
got 700MB (734003200 bytes), trying mlock ...locked. Loop 1/1:
Stuck Address : ok Random Value : ok Compare XOR : ok Compare SUB : ok Compare MUL : ok Compare DIV : ok Compare OR : ok Compare AND : ok Sequential Increment: ok Solid Bits : ok Block Sequential : ok Checkerboard : ok Bit Spread : ok Bit Flip : ok Walking Ones : ok Walking Zeroes : ok 8-bit Writes : ok 16-bit Writes : ok
Done.
Console output with DRAM clk 792:
U-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 21:34:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiB
root@orangepizero3:~# free -h
total used free shared buff/cache
available
Mem: 917Mi 134Mi 768Mi 360Ki 79Mi
782Mi
Swap: 0B 0B 0Broot@orangepizero3:~# memtester 700M 1 memtester version 4.6.0 (64-bit) Copyright (C) 2001-2020 Charles Cazabon. Licensed under the GNU General Public License version 2 (only).
pagesize is 4096
pagesizemask is 0xfffffffffffff000
want 700MB (734003200 bytes)
got 700MB (734003200 bytes), trying mlock ...locked. Loop 1/1:
Stuck Address : ok Random Value : ok Compare XOR : ok Compare SUB : ok Compare MUL : ok Compare DIV : ok Compare OR : ok Compare AND : ok Sequential Increment: ok Solid Bits : ok Block Sequential : ok Checkerboard : ok Bit Spread : ok Bit Flip : ok Walking Ones : ok Walking Zeroes : ok 8-bit Writes : ok 16-bit Writes : ok
Done.
Quoted 16 lines · Andre Przywara
This symptom is pretty surely not directly related to the DRAM frequency, it's caused by a missing barrier or delay *somewhere*. People report that this is fixed by adding another "
dsb();" at the beginning of themctl_mem_matches()function, but I don't have a good explanation why exactly there, and would like to avoid submitting patches that "just seem to work (TM)".If I find some time, I will try to setup some automated environment where I can run some experiments with different barrier locations. I can offer some rationale for putting it at the end of the function(s) that call
mctl_mem_matches(), so hope that this fixes it.Cheers,
Andre
Re: OrangePI Zero3 memory timing testing
Hi Stephen,
Quoted 7 lines · Stephen Graf
Some testing results:
With the default DRAM timing of 30x24=720, most often when my system boots it comes up with DRAM 2G, but I have a 1G system. Once in a while the boot shows 1G. When it shows 2G the linux OS also shows 2G and continuing does not make much sense.
On one boot where u-boot reported 1G the OS agreed and I ran memtester successfully.
If I build u-boot with
CONFIG_DRAM_CLK=792(33*24=792) I have never seen my system boot with anything other than DRAM 1G showing in u-boot. I ran
Interesting, many thanks for the elaborate experiments!
To be fair, the timing parameters were from Xunlong's setup, so with 792 MHz, but I remember that in my early testing this failed more often than not, so I reverted back to 720MHz. But I had different parameters back then, I believe. I will try to arrange some boot loop, to see how it fares with the 792 MHz, though I believe you that it's more stable. If that works, I will send a v2 with the USB and the DRAM clock fixed.
Thanks again for testing and the report!
Cheers,
Andre
Quoted 138 lines
memtester successfully and this system has been stable running linux 6.6.2.
Andre, if you can put together a few patches I can test them to see which works.
If anyone else with different variations of the Zero3 would test with the two DRAM timings and report results.
I also use the Zunlong image on occasion and it consistently shows 1G and from my poking around I think it runs at a 792 clk.
Console output with DRAM default:
U-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 22:46:39 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero3
DRAM: 2 GiBLast login: Wed Nov 29 09:35:15 PST 2023 on ttyS0
root@orangepizero3:~# free -h total used free shared buff/cache available Mem: 1.9Gi 139Mi 1.7Gi 360Ki 82Mi 1.7Gi Swap: 0B 0B 0BU-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 22:46:39 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero3
DRAM: 1 GiBroot@orangepizero3:~# free -h total used free shared buff/cache available Mem: 917Mi 137Mi 766Mi 360Ki 79Mi 780Mi Swap: 0B 0B 0Broot@orangepizero3:~# memtester 700M 1 memtester version 4.6.0 (64-bit) Copyright (C) 2001-2020 Charles Cazabon. Licensed under the GNU General Public License version 2 (only).pagesize is 4096
pagesizemask is0xfffffffffffff000
want 700MB (734003200 bytes)
got 700MB (734003200 bytes), trying mlock ...locked. Loop 1/1:
Stuck Address : ok
Random Value : ok
Compare XOR : ok
Compare SUB : ok
Compare MUL : ok
Compare DIV : ok
Compare OR : ok
Compare AND : ok
Sequential Increment: ok
Solid Bits : ok
Block Sequential : ok
Checkerboard : ok
Bit Spread : ok
Bit Flip : ok
Walking Ones : ok
Walking Zeroes : ok
8-bit Writes : ok
16-bit Writes : okDone.
Console output with DRAM clk 792:
U-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 21:34:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I)
Model: OrangePi Zero3
DRAM: 1 GiBroot@orangepizero3:~# free -h total used free shared buff/cache available Mem: 917Mi 134Mi 768Mi 360Ki 79Mi 782Mi Swap: 0B 0B 0Broot@orangepizero3:~# memtester 700M 1 memtester version 4.6.0 (64-bit) Copyright (C) 2001-2020 Charles Cazabon. Licensed under the GNU General Public License version 2 (only).pagesize is 4096
pagesizemask is0xfffffffffffff000
want 700MB (734003200 bytes)
got 700MB (734003200 bytes), trying mlock ...locked. Loop 1/1:
Stuck Address : ok
Random Value : ok
Compare XOR : ok
Compare SUB : ok
Compare MUL : ok
Compare DIV : ok
Compare OR : ok
Compare AND : ok
Sequential Increment: ok
Solid Bits : ok
Block Sequential : ok
Checkerboard : ok
Bit Spread : ok
Bit Flip : ok
Walking Ones : ok
Walking Zeroes : ok
8-bit Writes : ok
16-bit Writes : okDone.
Quoted 16 lines · Andre Przywara
This symptom is pretty surely not directly related to the DRAM frequency, it's caused by a missing barrier or delay *somewhere*. People report that this is fixed by adding another "
dsb();" at the beginning of themctl_mem_matches()function, but I don't have a good explanation why exactly there, and would like to avoid submitting patches that "just seem to work (TM)".If I find some time, I will try to setup some automated environment where I can run some experiments with different barrier locations. I can offer some rationale for putting it at the end of the function(s) that call
mctl_mem_matches(), so hope that this fixes it.Cheers,
Andre
Re: OrangePI Zero3 memory timing testing
Hello,
Please try to insert udelay() calls in addition to dsb() in the mctl_mem_matches()
and see if this helps. I suspect that there's just no way to do perfectly reliable
synchronization all the way from the CPU to DRAM and back in this particular scenario (which involves wacky things, such as accessing aliased physical memory addresses). So just having a generous delay may do the job and solve all the timing issues.
Another comment is about the use of memtester program. It's actually not very sensitive to memory reliability problems as-is.
Back in A10/A20 and H3 days, it was necessary to run memtester simultaneously with a Mali GPU rendered spinning textured cube animation for best results:
https://github.com/ssvb/lima-memtester
For example, a misconfigured H3 DRAM was showing no problems at all in the memtester test at 624MHz, but couldn't survive memtester together with the spinning textured cube until downclocked to 384MHz. Only aggressive simultaneous access from both CPU and GPU really exposes reliability problems. The other types of DMA transfers couldn't replace the GPU. It was also possible to use the G2D accelerator instead of the Mali GPU, but only when performing 90 degrees rotations. Doing simple non-rotated blits with G2D was useless and couldn't expose reliability problems.
I would suggest to install 3D drivers (whatever is available for the modern kernels
nowadays) and run some textured spinning cube demo together with memtester before deciding that your DRAM configuration is alright.
Quoted 174 lines · Andre Przywara
Hi Stephen,
Quoted 7 lines · Stephen Graf
Some testing results:
With the default DRAM timing of 30x24=720, most often when my system boots it comes up with DRAM 2G, but I have a 1G system. Once in a while the boot shows 1G. When it shows 2G the linux OS also shows 2G and continuing does not make much sense.
Quoted 5 lines
On one boot where u-boot reported 1G the OS agreed and I ran memtester successfully.
If I build u-boot with
CONFIG_DRAM_CLK=792(33*24=792) I have never seen my system boot with anything other than DRAM 1G showing in u-boot. I ranInteresting, many thanks for the elaborate experiments!
To be fair, the timing parameters were from Xunlong's setup, so with 792 MHz, but I remember that in my early testing this failed more often than not, so I reverted back to 720MHz. But I had different parameters back then, I believe. I will try to arrange some boot loop, to see how it fares with the 792 MHz, though I believe you that it's more stable. If that works, I will send a v2 with the USB and the DRAM clock fixed.Thanks again for testing and the report!
Cheers,
AndreQuoted 144 lines
memtester successfully and this system has been stable running linux 6.6.2.
Andre, if you can put together a few patches I can test them to see which works.
If anyone else with different variations of the Zero3 would test with the two DRAM timings and report results.
I also use the Zunlong image on occasion and it consistently shows 1G and from my poking around I think it runs at a 792 clk.
Console output with DRAM default:
U-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 22:46:39 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 2 GiBLast login: Wed Nov 29 09:35:15 PST 2023 on ttyS0
root@orangepizero3:~# free -h total used free shared buff/cache available Mem: 1.9Gi 139Mi 1.7Gi 360Ki 82Mi 1.7Gi Swap: 0B 0B 0BU-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 22:46:39 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiBroot@orangepizero3:~# free -h total used free shared buff/cache available Mem: 917Mi 137Mi 766Mi 360Ki 79Mi 780Mi Swap: 0B 0B 0Broot@orangepizero3:~# memtester 700M 1 memtester version 4.6.0 (64-bit) Copyright (C) 2001-2020 Charles Cazabon. Licensed under the GNU General Public License version 2 (only).pagesize is 4096
pagesizemask is0xfffffffffffff000
want 700MB (734003200 bytes)
got 700MB (734003200 bytes), trying mlock ...locked. Loop 1/1:Stuck Address : ok Random Value : ok Compare XOR : ok Compare SUB : ok Compare MUL : ok Compare DIV : ok Compare OR : ok Compare AND : ok Sequential Increment: ok Solid Bits : ok Block Sequential : ok Checkerboard : ok Bit Spread : ok Bit Flip : ok Walking Ones : ok Walking Zeroes : ok 8-bit Writes : ok 16-bit Writes : okDone.
Console output with DRAM clk 792:
U-Boot 2024.01-rc3-00028-g43f2873fa9-dirty (Nov 28 2023 - 21:34:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiBroot@orangepizero3:~# free -h total used free shared buff/cache available Mem: 917Mi 134Mi 768Mi 360Ki 79Mi 782Mi Swap: 0B 0B 0Broot@orangepizero3:~# memtester 700M 1 memtester version 4.6.0 (64-bit) Copyright (C) 2001-2020 Charles Cazabon. Licensed under the GNU General Public License version 2 (only).pagesize is 4096
pagesizemask is0xfffffffffffff000
want 700MB (734003200 bytes)
got 700MB (734003200 bytes), trying mlock ...locked. Loop 1/1:Stuck Address : ok Random Value : ok Compare XOR : ok Compare SUB : ok Compare MUL : ok Compare DIV : ok Compare OR : ok Compare AND : ok Sequential Increment: ok Solid Bits : ok Block Sequential : ok Checkerboard : ok Bit Spread : ok Bit Flip : ok Walking Ones : ok Walking Zeroes : ok 8-bit Writes : ok 16-bit Writes : okDone.
Quoted 16 lines · Andre Przywara
This symptom is pretty surely not directly related to the DRAM frequency, it's caused by a missing barrier or delay *somewhere*. People report that this is fixed by adding another "
dsb();" at the beginning of themctl_mem_matches()function, but I don't have a good explanation why exactly there, and would like to avoid submitting patches that "just seem to work (TM)".If I find some time, I will try to setup some automated environment where I can run some experiments with different barrier locations. I can offer some rationale for putting it at the end of the function(s) that call
mctl_mem_matches(), so hope that this fixes it.Cheers,
Andre
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
In reply to Stephen GrafOn Mon, 27 Nov 2023 12:21:44 -0800
Stephen Graf <[email protected]> wrote:
Hi Stephen!
Quoted 4 lines
Yes I forgot about the zBIT patch. With this patch also included I built and retested u-boot loaded from SPI flash. The two warning/error messages disappeared and the flash worked properly and booted from a USB device.
Great!
Quoted 4 lines
There was one message that I did not understand:
"Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment"
This is because there is no environment saved on the SPI flash (yet). You just copied the U-Boot image, the environment is in a separate area (behind that), defined by CONFIG_ENV_OFFSET, which is 64K below 1MB. There could be any kind of garbage there, initially, and U-Boot fortunately protects the environment with a checksum, so detects that this is not valid data, and falls back to the built-in environment. And frankly this is probably all you ever need, I think these days there is little that needs to be saved in the environment. If you want to give it a try, type "saveenv" on the U-Boot prompt. On the next boot U-Boot would detect this now properly initialised data region and you will probably not see the message anymore. But again this really only makes sense if you *change* something in the environment and want that preserved across reboots.
Quoted 4 lines
I tried to follow the u-boot documentation on writing the SPI flash but had problems with the write command. When issued it returned immediately. The erase command took about 5 sec to execute. I researched use of mtd commands and got a suggestion to use cat instead, which worked.
Mmh, can you elaborate on that? Did you mean you piped in the data into the mtd_debug command? Or did you write directly to /dev/mtd0, using cat? And which version of mtd_debug was this, exactly? I guess the official one from Debian Bookworm?
Cheers,
Andre
Quoted 151 lines
"root@orangepizero3:~# mtdinfo Count of MTD devices: 1 Present MTD devices: mtd0 Sysfs interface supported: yes root@orangepizero3:~# mtd_debug erase /dev/mtd0 0 0xf0000 Erased 983040 bytes from address 0x00000000 in flash root@orangepizero3:~# mtd_debug write /dev/mtd0 0 0xf0000 /home/sysadmin/u-boot-sunxi-with-spl.bin file_to_flash: fread, size 0xf0000, n 0xf0000 fread(): Success root@orangepizero3:~# cat /home/sysadmin/u-boot-sunxi-with-spl.bin > /dev/mtd0Console log of boot:
U-Boot SPL 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800)
DRAM: 1024 MiB
Trying to boot from sunxi SPINOTICE: BL31: v2.10.0 (debug):v2.10.0 NOTICE: BL31: Built : 18:07:18, Nov 23 2023 NOTICE: BL31: Detected Allwinner H616 SoC (1823) NOTICE: BL31: Found U-Boot DTB at 0x4a0b2798, model: OrangePi Zero3 INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP305 on RSB ERROR: RSB: set run-time address: 0x10003 INFO: Could not init RSB: -65539 INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for erratum 855873 was applied INFO: BL31: cortex_a53: CPU workaround for erratum 1530924 was applied INFO: PSCI: Suspend is unavailable INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9 INFO: Changed devicetree.U-Boot 2024.01-rc3-00012-g1fcf078f54-dirty (Nov 27 2023 - 10:17:46 -0800) Allwinner Technology
CPU: Allwinner H616 (SUN50I) Model: OrangePi Zero3 DRAM: 1 GiB Core: 57 devices, 25 uclasses, devicetree: separate WDT: Not starting watchdog@30090a0 MMC: mmc@4020000: 0Loading Environment from SPIFlash... SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environmentLoading Environment from FAT... Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **In: serial@5000000 Out: serial@5000000 Err: serial@5000000Allwinner mUSB OTG (Peripheral)
Net: eth0: ethernet@5020000using musb-hdrc, OUT ep1out IN ep1in STATUS
ep2in
MAC de:ad:be:ef:00:01
HOST MAC de:ad:be:ef:00:00
RNDIS ready
, eth1:usb_ether
starting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
Device NOT ready
Request Sense returned 02 3A 00
2 USB Device(s) found
scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110Device 0: Vendor: Generic- Rev: 1.00 Prod: SD/MMC
Type: Removable Hard Disk
Capacity: 3828.0 MB = 3.7 GB (7839744 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 1 ms (1.5 MiB/s)
## Executing script at4fc00000
Mainline u-boot / new-style environment detected.
This installer medium does not contain a suitable device-tree file for this system (allwinner/sun50i-h618-orangepi-zero3.dtb). Aborting boot process.
SCRIPT FAILED: continuing...
Found U-Boot script/boot/boot.scr
621 bytes read in 2 ms (302.7 KiB/s)
## Executing script at4fc00000
19472 bytes read in 3 ms (6.2 MiB/s)
Working FDT set to4fa00000
7088139 bytes read in 326 ms (20.7 MiB/s)
22491144 bytes read in 1031 ms (20.8 MiB/s)
Moving Image from0x40080000to0x40200000, end=41800000
## Loading init Ramdisk from Legacy Image at4ff00000...Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 7088075 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 4fa00000 Booting using the fdt blob at 0x4fa00000 Working FDT set to 4fa00000 Loading Ramdisk to 4993d000, end 49fff7cb ... OK Loading Device Tree to 00000000498cf000, end 000000004993cfff ... OKWorking FDT set to
498cf000Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.6.2 (orangepi@orangepizero3) (gcc (Debian12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sat Nov 25 18:37:47 UTC 2023
Quoted 25 lines · Andre Przywara
On Sat, 25 Nov 2023 20:27:05 -0800
Stephen Graf <[email protected]> wrote:Hi Stephen,
Quoted 2 lines
I built u-boot with the additional parameter for usb and it works, I think. There was one message that might be of concern " Card did not respond to voltage select! : -110".
This is a normal, though admittedly confusing message if no SD card is inserted. The code tries to (unconditionally) access the SD card, and sees that no card is there, the missing respond to the voltage select command is just the first real proof of this.
Quoted 6 lines
I am not sure of the details of the boot.cmd. The output below came from
the supplier image on an SD plugged into a USB card reader. The SD slot of the board was empty.I was able to install u-boot to the SPI flash memory and there is a warning message from that also: " Loading Environment from SPIFlash...
jedec_spi_norflash@0: unrecognized JEDEC id bytes: 5e, 40, 18 *** Warning -spi_flash_probe_bus_cs()failed, using default environment"So for a start there is no environment on the SPI flash yet, so it wouldn't do anything. But the "unrecognised JEDEC id bytes" message doesn't sound right. Can you dig into this? Do you have patch 1/3 applied, which tells U-Boot about
0x5emeaning zBIT?
Re: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
In reply to Andre PrzywaraOn 26.11.2023 03:23, Andre Przywara wrote:
Hi Andre,
Quoted 18 lines
On Sat, 25 Nov 2023 20:43:12 +0300
Mikhail Kalashnikov <[email protected]> wrote:Hi Mikhail,
Quoted 4 lines
Hi Andre!
Thanks for your patches. I started checking and noticed that USB storage was not working:Quoted 9 lines
=> usb reset
resetting USB...
Bus usb@5200000: USB EHCI 1.00
Bus usb@5200400: USB OHCI 1.0
scanning bus usb@5200000 for devices... 1 USB Device(s) found scanning bus usb@5200400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
=> usb storage
No storage devices, perhaps not 'usb start'ed..?
Quoted 6 lines
Ah, thanks for the report, seems I didn't even test this! So digging around I figured it's working in Linux, and it's the right USB port, but we are missing the VBUS power switch, which is a GPIO controlled regulator. There are pending patches to pick this from the devicetree[1], but we are not there yet, so we need:
CONFIG_USB1_VBUS_PIN="PC16"
With that usb storage work. Also I successfully loaded u-boot image to spi
with command:
sunxi-fel -p spiflash-write 0 u-boot-sunxi-with-spl.bin
100% [================================================] 828 kB, 74.7 kB/s
After that u-boot successful started from spi.
Best regards,
Mikhail
Quoted 107 lines
in the defconfig, for now. I will update the file. The same is actually missing from the OrangePi Zero2 defconfig, I will send a patch ASAP.
Quoted 8 lines
Otherwise my OpiZero3 (4GB) board looks working.
Ethernet works with my 10 Mbps usb-dongle.sf probe detect spi nor flash:
=> sf probe
SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiBQuoted 4 lines
Loading the kernel and running the operating system (from microsd) also without problems.
Tested-by Mikhail Kalashnikov <[email protected]>Great, thanks for the tag!
Cheers,
AndreQuoted 86 lines · Andre Przywara
Quoted 85 lines
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the
Makefileto actually build the .dtb.The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+)create mode 100644 configs/orangepi_zero3_defconfig
arch/arm/dts/Makefile +1
-0@@ -835,6 +835,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \ sun50i-h6-tanix-tx6-mini.dtb dtb-$(CONFIG_MACH_SUN50I_H616) += \ sun50i-h616-orangepi-zero2.dtb \ + sun50i-h618-orangepi-zero3.dtb \ sun50i-h616-x96-mate.dtb dtb-$(CONFIG_MACH_SUN50I) += \ sun50i-a64-amarula-relic.dtb \board/sunxi/MAINTAINERS +5
-0@@ -455,6 +455,11 @@ M: Jernej Skrabec <[email protected]> S: Maintained F: configs/orangepi_zero2_defconfig +ORANGEPI ZERO 3 BOARD +M: Andre Przywara <[email protected]> +S: Maintained +F: configs/orangepi_zero3_defconfig + ORANGEPI PC 2 BOARD M: Andre Przywara <[email protected]> S: Maintainedconfigs/orangepi_zero3_defconfig new file +30
-0@@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h618-orangepi-zero3" +CONFIG_SPL=y +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x07070707 +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e +CONFIG_DRAM_SUN50I_H616_ODT_EN=0xaaaaeeee +CONFIG_DRAM_SUN50I_H616_TPR6=0x44000000 +CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6663 +CONFIG_DRAM_SUN50I_H616_TPR11=0x24242624 +CONFIG_DRAM_SUN50I_H616_TPR12=0x0f0f100f +CONFIG_MACH_SUN50I_H616=y +CONFIG_SUNXI_DRAM_H616_LPDDR4=y +CONFIG_R_I2C_ENABLE=y +CONFIG_SPL_SPI_SUNXI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL_I2C=y +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_SYS_I2C_SLAVE=0x7f +CONFIG_SYS_I2C_SPEED=400000 +CONFIG_SPI_FLASH_ZBIT=y +CONFIG_PHY_MOTORCOMM=y +CONFIG_SUN8I_EMAC=y +CONFIG_AXP313_POWER=y +CONFIG_SPI=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_MUSB_GADGET=y
Bob McChesney
Tested-byRe: [PATCH 3/3] sunxi: H616: Add OrangePi Zero 3 board support
In reply to Mikhail KalashnikovQuoted 23 lines · Mikhail Kalashnikov
Tested-by Mikhail Kalashnikov <[email protected]>Quoted 20 lines · Andre Przywara
The OrangePi Zero 3 is a small development board featuring the Allwinner H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for which was recently added to U-Boot.Add a defconfig file selecting the right drivers and DRAM options. Since the .dts file was synced from the Linux kernel repo already, we just need to add one line to the
Makefileto actually build the .dtb.The DRAM parameters were derived from the values found in the BSP DRAM drivers on the SPI NOR flash.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/dts/Makefile | 1 + board/sunxi/MAINTAINERS | 5 +++++ configs/orangepi_zero3_defconfig | 30 ++++++++++++++++++++++++++++++ 3 files changed, 36 insertions(+)create mode 100644 configs/orangepi_zero3_defconfig
Am I ok to just tag onto Mikhail's email to add my tested tag? I've got a 4GB Orange Pi Zero 3 and can confirm that it works, despite any limitations that may be present.
Regards,
Bob