Skip to contentSkip to conversation

ARM: stm32: Permit multiple board targets

PATCH New Marek Vasut 4 participants 25 messages Jan 10, 2020 – Jan 20, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/5 ARM: stm32: Permit multiple board targets

Setting TARGET_STM32MP1 in Kconfig always forces SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME to values set by the ST reference platforms. Allow changing that by pulling out the TARGET_STM32MP157C_DK2 and making the ST reference platform settings conditional on TARGET_STM32MP157C_DK2 . Other platforms can now define a different TARGET_ and thus override the SYS_ settings in their Kconfig.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 board/st/stm32mp1/Kconfig | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
board/st/stm32mp1/Kconfig +5 -5
index 4fa2360b4f..c84aa41f06 100644
@@ -1,4 +1,8 @@
-if TARGET_STM32MP1
+config TARGET_STM32MP157C_DK2
+	bool "support of STMicroelectronics STM32MP157C-DK2 Discovery Board"
+	default y
+
+if TARGET_STM32MP157C_DK2
 
 config SYS_BOARD
 	default "stm32mp1"
@@ -22,8 +26,4 @@ config CMD_STBOARD
 	  This compile the stboard command to
 	  read and write the board in the OTP.
 
-config TARGET_STM32MP157C_DK2
-	bool "support of STMicroelectronics STM32MP157C-DK2 Discovery Board"
-	default y
-
 endif
Signature · 1 line
2.24.1
#1 lore raw

PATCH 2/5 ARM: stm32: Allow overriding setup_mac_address()

Let board code override setup_mac_address(), which is useful e.g. if the board derives the MAC address from another source, like an I2C EEPROM.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

---
V2: Add prototype to sys_proto.h

---
 arch/arm/mach-stm32mp/cpu.c                    | 2 +-
 arch/arm/mach-stm32mp/include/mach/sys_proto.h | 2 ++
 2 files changed, 3 insertions(+), 1 deletion(-)
arch/arm/mach-stm32mp/cpu.c +1 -1
index 6a71465494..de7891b5c4 100644
@@ -456,7 +456,7 @@ static void setup_boot_mode(void)
  * If there is no MAC address in the environment, then it will be initialized
  * (silently) from the value in the OTP.
  */
-static int setup_mac_address(void)
+__weak int setup_mac_address(void)
 {
 #if defined(CONFIG_NET)
 	int ret;
arch/arm/mach-stm32mp/include/mach/sys_proto.h +2 -0
index 99eefabf6e..47e57922d1 100644
@@ -30,3 +30,5 @@ u32 get_cpu_package(void);
 
 /* return boot mode */
 u32 get_bootmode(void);
+
+int setup_mac_address(void);
Signature · 1 line
2.24.1
#2 lore raw

PATCH 3/5 ARM: stm32: Fill in missing loadaddr

In reply to Marek Vasut

Since CONFIG_LOADADDR is not set, the default value of $loadaddr variable is not set in the environment either. Set the default load address to 256 MiB from the start of DRAM.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 include/configs/stm32mp1.h | 1 +
 1 file changed, 1 insertion(+)
include/configs/stm32mp1.h +1 -0
index 655833428e..b23dd38794 100644
@@ -36,6 +36,7 @@
  * Needed by "loadb"
  */
 #define CONFIG_SYS_LOAD_ADDR			STM32_DDR_BASE
+#define CONFIG_LOADADDR				0xd0000000
 
 /* ATAGs */
 #define CONFIG_CMDLINE_TAG
Signature · 1 line
2.24.1
#3 lore raw

PATCH 3/5 ARM: stm32: Fill in missing loadaddr

Hi Marek,

Quoted 19 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Since CONFIG_LOADADDR is not set, the default value of $loadaddr variable is not set in the environment either. Set the default load address to 256 MiB from the start of DRAM.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 include/configs/stm32mp1.h | 1 +
 1 file changed, 1 insertion(+)
include/configs/stm32mp1.h index renamed from include/configs/stm32mp1.h +0 -0

655833428e..b23dd38794 100644

include/configs/stm32mp1.h line 39

Quoted 4 lines
include/configs/stm32mp1.h +1 -0
@@ -36,6 +36,7 @@
  * Needed by "loadb"
  */
 #define CONFIG_SYS_LOAD_ADDR			STM32_DDR_BASE
+#define CONFIG_LOADADDR				0xd0000000

A offset a 256 MiB is really huge...
And I don't sure that will fit all the commands (bootm with zImage as it is xpecting to be placed in the first 128 MiB of RAM) and all the products (with lower memory)

I propose to have the same value for the 2 defines which define the default loadaddr with 32MB offset (same value that kernel_addr_r).

in stm32mp1.h, the defines becomes:

/*
* default load address used for command tftp, bootm , loadb, ... */
#define CONFIG_LOADADDR 0xc2000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

Regards
Patrick

#4 lore raw

PATCH 3/5 ARM: stm32: Fill in missing loadaddr

Quoted 31 lines · Patrick DELAUNAY

Hi Marek,

Quoted 19 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Since CONFIG_LOADADDR is not set, the default value of $loadaddr variable is not set in the environment either. Set the default load address to 256 MiB from the start of DRAM.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 include/configs/stm32mp1.h | 1 +
 1 file changed, 1 insertion(+)
include/configs/stm32mp1.h index renamed from include/configs/stm32mp1.h +0 -0

655833428e..b23dd38794 100644

include/configs/stm32mp1.h line 39

Quoted 4 lines
include/configs/stm32mp1.h +1 -0
@@ -36,6 +36,7 @@
  * Needed by "loadb"
  */
 #define CONFIG_SYS_LOAD_ADDR			STM32_DDR_BASE
+#define CONFIG_LOADADDR				0xd0000000

A offset a 256 MiB is really huge...
And I don't sure that will fit all the commands (bootm with zImage as it is xpecting to be placed in the first 128 MiB of RAM) and all the products (with lower memory)

Quoted 2 lines

I propose to have the same value for the 2 defines which define the default loadaddr with 32MB offset (same value that kernel_addr_r).

That's OK.

#5 lore raw

PATCH 3/5 ARM: stm32: Fill in missing loadaddr

Hi Marek,

Quoted 37 lines

From: Marek Vasut <[email protected]>
Sent: mercredi 15 janvier 2020 10:51

Quoted 16 lines · Patrick DELAUNAY

Hi Marek,

Quoted 14 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Since CONFIG_LOADADDR is not set, the default value of $loadaddr variable is not set in the environment either. Set the default load address to 256 MiB from the start of DRAM.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 include/configs/stm32mp1.h | 1 +
 1 file changed, 1 insertion(+)
Quoted 9 lines

include/configs/stm32mp1.h line 38

Quoted 9 lines
include/configs/stm32mp1.h +0 -0

index
655833428e..b23dd38794 100644

include/configs/stm32mp1.h +0 -0
@@ -36,6 +36,7 @@
  * Needed by "loadb"
  */
 #define CONFIG_SYS_LOAD_ADDR
	STM32_DDR_BASE
Quoted 7 lines

include/configs/stm32mp1.h line 39

Quoted 1 line
include/configs/stm32mp1.h +1 -0
+#define CONFIG_LOADADDR				0xd0000000

A offset a 256 MiB is really huge...
And I don't sure that will fit all the commands (bootm with zImage as it is xpecting to be placed in the first 128 MiB of RAM) and all the products (with lower memory)

Quoted 4 lines
Quoted 2 lines

I propose to have the same value for the 2 defines which define the default loadaddr with 32MB offset (same value that kernel_addr_r).

That's OK.

I take the patch with thte proposed offset = 32MB.

/*
- * Needed by "loadb"
+ * default load address used for command tftp, bootm , loadb, ... */
-#define CONFIG_SYS_LOAD_ADDR STM32_DDR_BASE
+#define CONFIG_LOADADDR 0xc2000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

Applied to u-boot-stm32/master, thanks!

Regards
Patrick

#6 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

In reply to Marek Vasut

Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel' is specified.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/stm32mp157c.dtsi | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/dts/stm32mp157c.dtsi +2 -0
index 6c670cf9a3..41aea75213 100644
@@ -1404,11 +1404,13 @@
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",
+				      "eth-ck",
 				      "ethstp",
 				      "syscfg-clk";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
 				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
 				 <&rcc ETHSTP>,
 				 <&rcc SYSCFG>;
 			st,syscon = <&syscfg 0x4>;
Signature · 1 line
2.24.1
#7 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

Hi Marek

Adding Christophe Roullier

Quoted 19 lines · Marek Vasut

Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel' is specified.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/stm32mp157c.dtsi | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/dts/stm32mp157c.dtsi +0 -0
index 6c670cf9a3..41aea75213 100644
@@ -1404,11 +1404,13 @@
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",

arch/arm/dts/stm32mp157c.dtsi line 1416

Quoted 10 lines
arch/arm/dts/stm32mp157c.dtsi +2 -0
+				      "eth-ck",
 				      "ethstp",
 				      "syscfg-clk";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
 				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
 				 <&rcc ETHSTP>,
 				 <&rcc SYSCFG>;
 			st,syscon = <&syscfg 0x4>;

Adding this clock is a particular case, it should be added in the board DT file, not in the SoC DT one.

Our ethernet expert ( Christophe  -in CC) is surprised that you don't need the following pin:

<STM32_PINMUX('G', 8, AF2)>, /* ETH_RMII_ETHCK */

To confirm, can you describe your ethernet config ?

Thanks

#8 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

Quoted 1 line · Patrice CHOTARD

Hi Marek

Hi,

Quoted 36 lines

Adding Christophe Roullier

Quoted 19 lines · Marek Vasut

Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel' is specified.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/stm32mp157c.dtsi | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/dts/stm32mp157c.dtsi +0 -0
index 6c670cf9a3..41aea75213 100644
@@ -1404,11 +1404,13 @@
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",

arch/arm/dts/stm32mp157c.dtsi line 1416

Quoted 10 lines
arch/arm/dts/stm32mp157c.dtsi +2 -0
+				      "eth-ck",
 				      "ethstp",
 				      "syscfg-clk";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
 				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
 				 <&rcc ETHSTP>,
 				 <&rcc SYSCFG>;
 			st,syscon = <&syscfg 0x4>;

Adding this clock is a particular case, it should be added in the board DT file, not in the SoC DT one.

Quoted 5 lines

Our ethernet expert ( Christophe  -in CC) is surprised that you don't need the following pin:

<STM32_PINMUX('G', 8, AF2)>, /* ETH_RMII_ETHCK */

To confirm, can you describe your ethernet config ?

I need 50 MHz RMII clock output for PHY on PA1, PG8 is completely unused.

#9 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

In reply to Marek Vasut

Hi Marek,

+ Christophe (Maintainer in kernel)

Quoted 22 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel'
is specified.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/stm32mp157c.dtsi | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/dts/stm32mp157c.dtsi index renamed from arch/arm/dts/stm32mp157c.dtsi +0 -0

6c670cf9a3..41aea75213 100644

arch/arm/dts/stm32mp157c.dtsi +0 -0
@@ -1404,11 +1404,13 @@
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",

arch/arm/dts/stm32mp157c.dtsi line 1416

Quoted 10 lines
arch/arm/dts/stm32mp157c.dtsi +2 -0
+				      "eth-ck",
 				      "ethstp",
 				      "syscfg-clk";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
 				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
 				 <&rcc ETHSTP>,
 				 <&rcc SYSCFG>;
 			st,syscon = <&syscfg 0x4>;

This clock is optional, not needed by default for STM32MP15x:
this clock is used only for a specific case: Phy without quartz, for all the other case we don't need to switch on this clock.

Normally if it is the case, it should be done in board part, not in SOC device tree (is is the strategy chosen by kernel). Moreover stm32mp157c.dtsi is just a copy of the kernel one, so this patch also need to be accepted by Kernel Maintainers.

NB: if you are in the Phy without crytal 50MHz (rmii + "st,eth_ref_clk_sel" + "eth-ck"),
You should have also the associated pin in the device tree of the board :

+ <STM32_PINMUX('G', 8, AF2)>, /* ETH_RMII_ETHCK */

Christophe you can complete my answer if it is not enough clear.

regards

Patrick

#10 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

Quoted 1 line · Patrick DELAUNAY

Hi Marek,

Hi,

Quoted 29 lines

+ Christophe (Maintainer in kernel)

Quoted 27 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel'
is specified.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/stm32mp157c.dtsi | 2 ++
 1 file changed, 2 insertions(+)
arch/arm/dts/stm32mp157c.dtsi index renamed from arch/arm/dts/stm32mp157c.dtsi +0 -0

6c670cf9a3..41aea75213 100644

arch/arm/dts/stm32mp157c.dtsi +1 -0
@@ -1404,11 +1404,13 @@
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",
+				      "eth-ck",
 				      "ethstp",
 				      "syscfg-clk";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
Quoted 8 lines

arch/arm/dts/stm32mp157c.dtsi line 1416

Quoted 5 lines
arch/arm/dts/stm32mp157c.dtsi +1 -0
 				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
 				 <&rcc ETHSTP>,
 				 <&rcc SYSCFG>;
 			st,syscon = <&syscfg 0x4>;

This clock is optional, not needed by default for STM32MP15x:
this clock is used only for a specific case: Phy without quartz, for all the other case we don't need to switch on this clock.

That's the usecase here.

Quoted 7 lines

Normally if it is the case, it should be done in board part, not in SOC device tree (is is the strategy chosen by kernel). Moreover stm32mp157c.dtsi is just a copy of the kernel one, so this patch also need to be accepted by Kernel Maintainers.

NB: if you are in the Phy without crytal 50MHz (rmii + "st,eth_ref_clk_sel" + "eth-ck"),
You should have also the associated pin in the device tree of the board :

+ <STM32_PINMUX('G', 8, AF2)>, /* ETH_RMII_ETHCK */

My PHY is _NOT_ connected to this pin, the output clock of the SoC are PA1.

Quoted 1 line

Christophe you can complete my answer if it is not enough clear.

I would expect that you should describe _all_ the clock which are routed into the ethernet IP in the DT and if the driver doesn't need some of those clock, the driver should just not enable such clock.

#11 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

Quoted 48 lines · Marek Vasut
Quoted 1 line · Patrick DELAUNAY

Hi Marek,

Hi,

Quoted 28 lines

+ Christophe (Maintainer in kernel)

Quoted 26 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel'
is specified.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
  arch/arm/dts/stm32mp157c.dtsi | 2 ++
  1 file changed, 2 insertions(+)
arch/arm/dts/stm32mp157c.dtsi index renamed from arch/arm/dts/stm32mp157c.dtsi +0 -0

6c670cf9a3..41aea75213 100644

arch/arm/dts/stm32mp157c.dtsi +1 -0
@@ -1404,11 +1404,13 @@
  			clock-names = "stmmaceth",
  				      "mac-clk-tx",
  				      "mac-clk-rx",
+				      "eth-ck",
  				      "ethstp",
  				      "syscfg-clk";
  			clocks = <&rcc ETHMAC>,
Quoted 8 lines

arch/arm/dts/stm32mp157c.dtsi line 1416

Quoted 6 lines
arch/arm/dts/stm32mp157c.dtsi +1 -0
  				 <&rcc ETHTX>,
  				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
  				 <&rcc ETHSTP>,
  				 <&rcc SYSCFG>;
  			st,syscon = <&syscfg 0x4>;

This clock is optional, not needed by default for STM32MP15x:
this clock is used only for a specific case: Phy without quartz, for all the other case we don't need to switch on this clock.

That's the usecase here.

Quoted 6 lines

Normally if it is the case, it should be done in board part, not in SOC device tree (is is the strategy chosen by kernel). Moreover stm32mp157c.dtsi is just a copy of the kernel one, so this patch also need to be accepted by Kernel Maintainers.

NB: if you are in the Phy without crytal 50MHz (rmii + "st,eth_ref_clk_sel" + "eth-ck"),
You should have also the associated pin in the device tree of the board :

Quoted 7 lines
Quoted 1 line

+ <STM32_PINMUX('G', 8, AF2)>, /* ETH_RMII_ETHCK */

My PHY is _NOT_ connected to this pin, the output clock of the SoC are PA1.

Quoted 1 line

Christophe you can complete my answer if it is not enough clear.

I would expect that you should describe _all_ the clock which are routed into the ethernet IP in the DT and if the driver doesn't need some of those clock, the driver should just not enable such clock.

Hi Marek,

You are right, we will add by default all clocks used by stm32mp157, and modify driver to decide if we need to enable it or not.

So ACK to add ETHCK_K in stm32mp157c.dtsi

Regards,

Christophe

#12 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

On 1/13/20 5:14 PM, Christophe ROULLIER wrote:
[...]

Quoted 6 lines
Quoted 4 lines
Quoted 1 line

Christophe you can complete my answer if it is not enough clear.

I would expect that you should describe _all_ the clock which are routed into the ethernet IP in the DT and if the driver doesn't need some of those clock, the driver should just not enable such clock.

Hi Marek,

Hi,

Quoted 4 lines

You are right, we will add by default all clocks used by stm32mp157, and modify driver to decide if we need to enable it or not.

So ACK to add ETHCK_K in stm32mp157c.dtsi

Do you want me to send the kernel patch ? I have it somewhere here too, I can roll it out tomorrow-ish.

#13 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

Quoted 7 lines · Marek Vasut

On 1/13/20 5:14 PM, Christophe ROULLIER wrote:
[...]

Quoted 5 lines
Quoted 4 lines
Quoted 1 line

Christophe you can complete my answer if it is not enough clear.

I would expect that you should describe _all_ the clock which are routed into the ethernet IP in the DT and if the driver doesn't need some of those clock, the driver should just not enable such clock.

Hi Marek,

Quoted 8 lines

Hi,

Quoted 4 lines

You are right, we will add by default all clocks used by stm32mp157, and modify driver to decide if we need to enable it or not.

So ACK to add ETHCK_K in stm32mp157c.dtsi

Do you want me to send the kernel patch ? I have it somewhere here too, I can roll it out tomorrow-ish.

Hi Marek,

I have not changed yet, the kernel and uboot driver code, to manage this behavior. I will implement and push new code soon.

Regards

Christophe.

#14 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

Quoted 13 lines · Christophe ROULLIER
Quoted 12 lines · Marek Vasut

On 1/13/20 5:14 PM, Christophe ROULLIER wrote:
[...]

Quoted 5 lines
Quoted 4 lines
Quoted 1 line

Christophe you can complete my answer if it is not enough clear.

I would expect that you should describe _all_ the clock which are routed into the ethernet IP in the DT and if the driver doesn't need some of those clock, the driver should just not enable such clock.

Hi Marek,

Hi,

Quoted 3 lines

You are right, we will add by default all clocks used by stm32mp157, and modify driver to decide if we need to enable it or not.

Quoted 8 lines
Quoted 3 lines
Quoted 1 line

So ACK to add ETHCK_K in stm32mp157c.dtsi

Do you want me to send the kernel patch ? I have it somewhere here too, I can roll it out tomorrow-ish.

Hi Marek,

I have not changed yet, the kernel and uboot driver code, to manage this behavior. I will implement and push new code soon.

The kernel code already does what is needed. You only need similar patch
to the DT, cfr attachment.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 0001-ARM-dts-stm32-Add-missing-ETHCK-clock-to-ethernet-no.patch
Type: text/x-patch
Size: 1149 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200114/27e6a621/attachment.bin>

#15 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

Quoted 15 lines · Marek Vasut
Quoted 14 lines · Christophe ROULLIER
Quoted 13 lines · Marek Vasut

On 1/13/20 5:14 PM, Christophe ROULLIER wrote:
[...]

Quoted 5 lines
Quoted 4 lines
Quoted 1 line

Christophe you can complete my answer if it is not enough clear.

I would expect that you should describe _all_ the clock which are routed into the ethernet IP in the DT and if the driver doesn't need some of those clock, the driver should just not enable such clock.

Hi Marek,

Hi,

Quoted 4 lines

You are right, we will add by default all clocks used by stm32mp157, and modify driver to decide if we need to enable it or not.

So ACK to add ETHCK_K in stm32mp157c.dtsi

Quoted 8 lines
Quoted 6 lines
Quoted 2 lines

Do you want me to send the kernel patch ? I have it somewhere here too, I can roll it out tomorrow-ish.

Hi Marek,

I have not changed yet, the kernel and uboot driver code, to manage this behavior. I will implement and push new code soon.

The kernel code already does what is needed. You only need similar patch to the DT, cfr attachment.

Yes, I'm aligned Marek (I've also done the glue driver in kernel :-))

But what I need to do in uboot and kernel driver it is to add by default all clocks in dtsi file

and modified driver to manage them in my driver (enable or disable it in function of phy mode, if with or without quartz in PHY etc..)

Regards,

Christophe.

#16 lore raw

PATCH 4/5 ARM: dts: stm32: Add missing ETHCK clock to ethernet node

In reply to Christophe ROULLIER

Hi Marek,

Quoted 66 lines

From: Christophe ROULLIER <[email protected]>
Sent: lundi 13 janvier 2020 17:15

Quoted 41 lines · Marek Vasut
Quoted 1 line · Patrick DELAUNAY

Hi Marek,

Hi,

Quoted 37 lines

+ Christophe (Maintainer in kernel)

Quoted 23 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Add missing 'eth-ck' clock to the ethernet node. These clock are used to generate external clock signal for the PHY in case 'st,eth_ref_clk_sel' is specified.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
  arch/arm/dts/stm32mp157c.dtsi | 2 ++
  1 file changed, 2 insertions(+)
(quoted diff) +0 -0

b/arch/arm/dts/stm32mp157c.dtsi index
6c670cf9a3..41aea75213 100644

arch/arm/dts/stm32mp157c.dtsi +0 -0
@@ -1404,11 +1404,13 @@
  			clock-names = "stmmaceth",
  				      "mac-clk-tx",
  				      "mac-clk-rx",

arch/arm/dts/stm32mp157c.dtsi line 1416

Quoted 10 lines
arch/arm/dts/stm32mp157c.dtsi +2 -0
+				      "eth-ck",
  				      "ethstp",
  				      "syscfg-clk";
  			clocks = <&rcc ETHMAC>,
  				 <&rcc ETHTX>,
  				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
  				 <&rcc ETHSTP>,
  				 <&rcc SYSCFG>;
  			st,syscon = <&syscfg 0x4>;

This clock is optional, not needed by default for STM32MP15x:
this clock is used only for a specific case: Phy without quartz, for all the other

case we don't need to switch on this clock.

Quoted 3 lines

That's the usecase here.

Quoted 1 line

Normally if it is the case, it should be done in board part, not in SOC device

tree (is is the strategy chosen by kernel).

Quoted 1 line
Quoted 1 line

Moreover stm32mp157c.dtsi is just a copy of the kernel one, so this patch also

need to be accepted by Kernel Maintainers.

Quoted 2 lines
Quoted 2 lines

NB: if you are in the Phy without crytal 50MHz (rmii + "st,eth_ref_clk_sel" +

"eth-ck"),

Quoted 9 lines
Quoted 3 lines

You should have also the associated pin in the device tree of the board :

+ <STM32_PINMUX('G', 8, AF2)>, /* ETH_RMII_ETHCK */

My PHY is _NOT_ connected to this pin, the output clock of the SoC are PA1.

Quoted 1 line

Christophe you can complete my answer if it is not enough clear.

I would expect that you should describe _all_ the clock which are routed into the ethernet IP in the DT and if the driver doesn't need some of those clock, the driver should just not enable such clock.

Quoted 6 lines

Hi Marek,

You are right, we will add by default all clocks used by stm32mp157, and modify driver to decide if we need to enable it or not.

So ACK to add ETHCK_K in stm32mp157c.dtsi

Christophe: thanks for ACK,

And I add the patch in U-Boot device tree by advance (the only possible impact is to switch on a not used clock).

Applied to u-boot-stm32/master, thanks!

Regards
Patrick

#17 lore raw

PATCH 5/5 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

In reply to Marek Vasut

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/Makefile                         |   1 +
 .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
 arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
 arch/arm/mach-stm32mp/Kconfig                 |   1 +
 board/dhelectronics/dh_stm32mp1/Kconfig       |  25 +
 board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
 board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
 board/dhelectronics/dh_stm32mp1/board.c       | 777 ++++++++++++++++++
 configs/stm32mp15_dhcom_basic_defconfig       | 140 ++++
 11 files changed, 1675 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
 create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
 create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
 create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
 create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
 create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
arch/arm/dts/Makefile +1 -0
index 983e235f44..82489bc09c 100644
@@ -859,6 +859,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_TARGET_STM32MP1) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157c-dhcom-pdk2-u-boot.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb
arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts new file +7 -0
new file mode 100644
index 0000000000..fd99988570
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>
+ */
+
+#include "stm32mp157c-dhcom-pdk2.dts"
+#include "stm32mp157c-dhcom-u-boot.dtsi"
arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +88 -0

88 lines not on this page · raw message

arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +238 -0

238 lines not on this page · raw message

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +379 -0

379 lines not on this page · raw message

arch/arm/mach-stm32mp/Kconfig +1 -0
index ae28f6e206..1aa5f8a122 100644
@@ -147,5 +147,6 @@ config DEBUG_UART_CLOCK
 endif
 
 source "board/st/stm32mp1/Kconfig"
+source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
 endif
board/dhelectronics/dh_stm32mp1/Kconfig new file +25 -0
new file mode 100644
index 0000000000..e751a3e5ed
@@ -0,0 +1,25 @@
+config TARGET_DH_STM32MP1_PDK2
+	bool "support of DH STM32MP1 PDK2"
+	default y
+
+if TARGET_DH_STM32MP1_PDK2
+
+config SYS_BOARD
+	default "dh_stm32mp1"
+
+config SYS_VENDOR
+	default "dhelectronics"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET_REDUND
+	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
+
+endif
board/dhelectronics/dh_stm32mp1/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..38f54a3da4
@@ -0,0 +1,7 @@
+DH_STM32MP1_PDK2 BOARD
+M:	Marek Vasut <[email protected]>
+S:	Maintained
+F:	arch/arm/dts/stm32mp157c-dhcom*
+F:	board/dhelectronics/dh_stm32mp1/
+F:	configs/stm32mp15_dhcom_basic_defconfig
+F:	include/configs/stm32mp1.h
board/dhelectronics/dh_stm32mp1/Makefile new file +12 -0
new file mode 100644
index 0000000000..a9d28218ef
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+#
+# Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += ../../st/stm32mp1/spl.o
+else
+obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o
+endif
+
+obj-y += ../../st/stm32mp1/board.o board.o
board/dhelectronics/dh_stm32mp1/board.c new file +777 -0

777 lines not on this page · raw message

configs/stm32mp15_dhcom_basic_defconfig new file +140 -0

140 lines not on this page · raw message

Signature · 1 line
2.24.1
#18 lore raw

PATCH 5/5 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Hi Marek,

Quoted 195 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29
To: u-boot at lists.denx.de
Cc: Marek Vasut <[email protected]>; Patrick DELAUNAY <[email protected]>; Patrice CHOTARD <[email protected]>
Subject: [PATCH 5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board
Importance: High

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 arch/arm/dts/Makefile                         |   1 +
 .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
 arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
 arch/arm/mach-stm32mp/Kconfig                 |   1 +
 board/dhelectronics/dh_stm32mp1/Kconfig       |  25 +
 board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
 board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
 board/dhelectronics/dh_stm32mp1/board.c       | 777 ++++++++++++++++++
 configs/stm32mp15_dhcom_basic_defconfig       | 140 ++++
 11 files changed, 1675 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
 create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
 create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
 create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
 create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
 create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
arch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0 -0

983e235f44..82489bc09c 100644

arch/arm/dts/Makefile +1 -0
@@ -859,6 +859,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_TARGET_STM32MP1) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157c-dhcom-pdk2-u-boot.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb
arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts new file +6 -0
new file mode 100644
index 0000000000..fd99988570
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include "stm32mp157c-dhcom-pdk2.dts"
+#include "stm32mp157c-dhcom-u-boot.dtsi"
arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +8 -0
new file mode 100644
index 0000000000..05aa545f55
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include "stm32mp157c-dhcom.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C DHCOM Premium

Developer Kit (2)";

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +48 -0
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth_ref_clk_sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy at 1 {
+			reg = <1>;
+		};
+	};
+};
+
+&pinctrl {
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /*

ETH1_RMII_TXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('G', 14, AF11)>, /*

ETH1_RMII_TXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('B', 11, AF11)>, /*

ETH1_RMII_TX_EN */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 1, AF0)>,   /*

ETH1_RMII_REF_CLK */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO

*/

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC

*/

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +6 -0
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /*

ETH1_RMII_RXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 5, AF11)>,  /*

ETH1_RMII_RXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 7, AF11)>;  /*

ETH1_RMII_CRS_DV */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +7 -0
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /*

ETH1_RMII_TXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('G', 14, ANALOG)>, /*

ETH1_RMII_TXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('B', 11, ANALOG)>, /*

ETH1_RMII_TX_EN */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /*

ETH1_MDIO */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /*

ETH1_MDC */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /*

ETH1_RMII_RXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /*

ETH1_RMII_RXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /*

ETH1_RMII_REF_CLK */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /*

ETH1_RMII_CRS_DV */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +3 -0
+		};
+	};
+};
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +12 -0
new file mode 100644
index 0000000000..320912edd8
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp157-u-boot.dtsi"
+#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
+
+/ {
+	aliases {
+		i2c1 = &i2c2;
+		i2c3 = &i2c4;

arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi line 22

Quoted 10 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +10 -0
+		i2c4 = &i2c5;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		spi0 = &qspi;
+		usb0 = &usbotg_hs;
+	};
+
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";

Excpet if I miss something, You have no led on your board (named = "heartbeat" or "error" ) This 2 line can be remove I think

Quoted 6 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +6 -0
+		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+	};
+
+	led {
+		red {

arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi line 39

Quoted 10 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +10 -0
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+
+		blue {
+			default-state = "on";
+		};
+	};

This blue overridde can be remove I think.

Quoted 601 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +199 -0
+};
+
+&i2c4 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&flash0 {
+	u-boot,dm-spl;
+};
+
+&qspi {
+	u-boot,dm-spl;
+};
+
+&qspi_clk_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk1_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk2_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_PLL4P
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4Q
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll at 0 {
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll at 1 {
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll at 2 {
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
+	pll4: st,pll at 3 {
+		cfg = < 1 49 11 11 11 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
arch/arm/dts/stm32mp157c- renamed from arch/arm/dts/stm32mp157c-dhcom.dtsi +0 -0

dhcom.dtsi
new file mode 100644
index 0000000000..96661ae783

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +228 -0
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */ /dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&dcmi {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_a>;
+	pinctrl-1 = <&dcmi_sleep_pins_a>;
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	status = "okay";
+};
+
+&pwr {
+	pwr-regulators {
+		vdd-supply = <&vdd>;
+		vdd_3v3_usbfs-supply = <&vdd_usb>;
+	};
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a

&qspi_bk2_sleep_pins_a>;

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +149 -0
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	flash1: mx66l51235l at 1 {
+		compatible = "jedec,spi-nor";
+		reg = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,sig-dir;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	status = "disabled";
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 1 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	timer at 5 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 7 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/mach-stm32mp/Kconfig +1 -0
index ae28f6e206..1aa5f8a122 100644
@@ -147,5 +147,6 @@ config DEBUG_UART_CLOCK  endif
 
 source "board/st/stm32mp1/Kconfig"
+source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
 endif
board/dhelectronics/dh_stm32mp1/Kconfig new file +0 -0
new file mode 100644
index 0000000000..e751a3e5ed

board/dhelectronics/dh_stm32mp1/Kconfig line 3

Quoted 3 lines
board/dhelectronics/dh_stm32mp1/Kconfig new file +3 -0
@@ -0,0 +1,25 @@
+config TARGET_DH_STM32MP1_PDK2
+	bool "support of DH STM32MP1 PDK2"
+	default y

Avoid set default y here....
to avoid to activate this config for ST board.

In fact it should be a choice between the 2 targets
- TARGET_DH_STM32MP1_PDK2
- TARGET_ST_STM32MP1

Quoted 43 lines
board/dhelectronics/dh_stm32mp1/Kconfig new file +22 -0
+
+if TARGET_DH_STM32MP1_PDK2
+
+config SYS_BOARD
+	default "dh_stm32mp1"
+
+config SYS_VENDOR
+	default "dhelectronics"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET_REDUND
+	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
+
+endif
board/dhelectronics/dh_stm32mp1/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..38f54a3da4
@@ -0,0 +1,7 @@
+DH_STM32MP1_PDK2 BOARD
+M:	Marek Vasut <[email protected]>
+S:	Maintained
+F:	arch/arm/dts/stm32mp157c-dhcom*
+F:	board/dhelectronics/dh_stm32mp1/
+F:	configs/stm32mp15_dhcom_basic_defconfig
+F:	include/configs/stm32mp1.h
board/dhelectronics/dh_stm32mp1/Makefile new file +0 -0
new file mode 100644
index 0000000000..a9d28218ef

board/dhelectronics/dh_stm32mp1/Makefile line 8

Quoted 8 lines
board/dhelectronics/dh_stm32mp1/Makefile new file +8 -0
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause # # Copyright (C)
+2018, STMicroelectronics - All Rights Reserved #
+
+ifdef CONFIG_SPL_BUILD
+obj-y += ../../st/stm32mp1/spl.o
+else
+obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o endif
+

I don't think you wee to support the command STMicroelctronics board (ref MBxxxx). it is only a internal command for ST : save/read board id in OTP.

Quoted 150 lines
board/dhelectronics/dh_stm32mp1/Makefile new file +1 -0
+obj-y += ../../st/stm32mp1/board.o board.o
board/dhelectronics/dh_stm32mp1/board.c new file +94 -0
new file mode 100644
index 0000000000..54cc3b7587
@@ -0,0 +1,777 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved  */
+
+#include <common.h>
+#include <adc.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <bootm.h>
+#include <clk.h>
+#include <config.h>
+#include <dm.h>
+#include <dm/device.h>
+#include <dm/uclass.h>
+#include <env.h>
+#include <env_internal.h>
+#include <g_dnl.h>
+#include <generic-phy.h>
+#include <i2c.h>
+#include <i2c_eeprom.h>
+#include <init.h>
+#include <led.h>
+#include <memalign.h>
+#include <misc.h>
+#include <mtd.h>
+#include <mtd_node.h>
+#include <netdev.h>
+#include <phy.h>
+#include <power/regulator.h>
+#include <remoteproc.h>
+#include <reset.h>
+#include <syscon.h>
+#include <usb.h>
+#include <usb/dwc2_udc.h>
+#include <watchdog.h>
+
+/* SYSCFG registers */
+#define SYSCFG_BOOTR		0x00
+#define SYSCFG_PMCSETR		0x04
+#define SYSCFG_IOCTRLSETR	0x18
+#define SYSCFG_ICNR		0x1C
+#define SYSCFG_CMPCR		0x20
+#define SYSCFG_CMPENSETR	0x24
+#define SYSCFG_PMCCLRR		0x44
+
+#define SYSCFG_BOOTR_BOOT_MASK		GENMASK(2, 0)
+#define SYSCFG_BOOTR_BOOTPD_SHIFT	4
+
+#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE		BIT(0)
+#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI	BIT(1)
+#define SYSCFG_IOCTRLSETR_HSLVEN_ETH		BIT(2)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC		BIT(3)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SPI		BIT(4)
+
+#define SYSCFG_CMPCR_SW_CTRL		BIT(1)
+#define SYSCFG_CMPCR_READY		BIT(8)
+
+#define SYSCFG_CMPENSETR_MPU_EN		BIT(0)
+
+#define SYSCFG_PMCSETR_ETH_CLK_SEL	BIT(16)
+#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL	BIT(17)
+
+#define SYSCFG_PMCSETR_ETH_SELMII	BIT(20)
+
+#define SYSCFG_PMCSETR_ETH_SEL_MASK	GENMASK(23, 21)
+#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII	0
+#define SYSCFG_PMCSETR_ETH_SEL_RGMII	BIT(21)
+#define SYSCFG_PMCSETR_ETH_SEL_RMII	BIT(23)
+
+/*
+ * Get a global data pointer
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+int setup_mac_address(void)
+{
+	struct udevice *dev;
+	ofnode eeprom;
+	unsigned char enetaddr[6];
+	int ret;
+
+	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
+	if (ret)	/* ethaddr is already set */
+		return 0;
+
+	eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
+	if (!ofnode_valid(eeprom)) {
+		printf("Invalid hardware path to EEPROM!\n");
+		return -ENODEV;
+	}
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom,

&dev);

board/dhelectronics/dh_stm32mp1/board.c new file +46 -0
+	if (ret) {
+		printf("Cannot find EEPROM!\n");
+		return ret;
+	}
+
+	ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
+	if (ret) {
+		printf("Error reading configuration EEPROM!\n");
+		return ret;
+	}
+
+	if (is_valid_ethaddr(enetaddr))
+		eth_env_set_enetaddr("ethaddr", enetaddr);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	int ret;
+	char *mode;
+	u32 otp;
+	struct udevice *dev;
+	const char *fdt_compat;
+	int fdt_compat_len;
+
+	if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
+		mode = "trusted with OP-TEE";
+	else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
+		mode = "trusted";
+	else
+		mode = "basic";
+
+	printf("Board: stm32mp1 in %s mode", mode);
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len)
+		printf(" (%s)", fdt_compat);
+	puts("\n");
+
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev,

STM32_BSEC_SHADOW(BSEC_OTP_BOARD),

board/dhelectronics/dh_stm32mp1/board.c line 149

Quoted 8 lines
board/dhelectronics/dh_stm32mp1/board.c new file +8 -0
+				&otp, sizeof(otp));
+	if (ret > 0 && otp) {
+		printf("Board: MB%04x Var%d Rev.%c-%02d\n",
+		       otp >> 16,
+		       (otp >> 12) & 0xF,
+		       ((otp >> 8) & 0xF) - 1 + 'A',
+		       otp & 0xF);
+	}

This part (read OTP / / display MBxxx ) can be dropped for your board (it is a ST specific part).

Quoted 41 lines
board/dhelectronics/dh_stm32mp1/board.c new file +41 -0
+	return 0;
+}
+
+static void board_key_check(void)
+{
+#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
+	ofnode node;
+	struct gpio_desc gpio;
+	enum forced_boot_mode boot_mode = BOOT_NORMAL;
+
+	node = ofnode_path("/config");
+	if (!ofnode_valid(node)) {
+		debug("%s: no /config node?\n", __func__);
+		return;
+	}
+#ifdef CONFIG_FASTBOOT
+	if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,fastboot-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("Fastboot key pressed, ");
+			boot_mode = BOOT_FASTBOOT;
+		}
+
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+#ifdef CONFIG_CMD_STM32PROG
+	if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,stm32prog-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("STM32Programmer key pressed, ");
+			boot_mode = BOOT_STM32PROG;
+		}
+		dm_gpio_free(NULL, &gpio);
+	}

board/dhelectronics/dh_stm32mp1/board.c line 201

Quoted 10 lines
board/dhelectronics/dh_stm32mp1/board.c new file +10 -0
+#endif
+
+	if (boot_mode != BOOT_NORMAL) {
+		puts("entering download mode...\n");
+		clrsetbits_le32(TAMP_BOOT_CONTEXT,
+				TAMP_BOOT_FORCED_MASK,
+				boot_mode);
+	}
+#endif
+}

Do you support GPIO key press on GPAIOA14 / 15 (as it is done in ST boards EV1 : DK1 / DK2) If no all this function can be dropped.

Quoted 60 lines

+#if defined(CONFIG_USB_GADGET) &&
defined(CONFIG_USB_GADGET_DWC2_OTG)

board/dhelectronics/dh_stm32mp1/board.c new file +25 -0
+
+/* STMicroelectronics STUSB1600 Type-C controller */
+#define STUSB1600_CC_CONNECTION_STATUS		0x0E
+
+/* STUSB1600_CC_CONNECTION_STATUS bitfields */
+#define STUSB1600_CC_ATTACH			BIT(0)
+
+static int stusb1600_init(struct udevice **dev_stusb1600) {
+	ofnode node;
+	struct udevice *dev, *bus;
+	int ret;
+	u32 chip_addr;
+
+	*dev_stusb1600 = NULL;
+
+	/* if node stusb1600 is present, means DK1 or DK2 board */
+	node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
+	if (!ofnode_valid(node))
+		return -ENODEV;
+
+	ret = ofnode_read_u32(node, "reg", &chip_addr);
+	if (ret)
+		return -EINVAL;
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C,

ofnode_get_parent(node),

board/dhelectronics/dh_stm32mp1/board.c new file +17 -0
+					  &bus);
+	if (ret) {
+		printf("bus for stusb1600 not found\n");
+		return -ENODEV;
+	}
+
+	ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
+	if (!ret)
+		*dev_stusb1600 = dev;
+
+	return ret;
+}
+
+static int stusb1600_cable_connected(struct udevice *dev) {
+	u8 status;
+
+	if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status,

1))

board/dhelectronics/dh_stm32mp1/board.c new file +14 -0
+		return 0;
+
+	return status & STUSB1600_CC_ATTACH;
+}
+
+#include <usb/dwc2_udc.h>
+int g_dnl_board_usb_cable_connected(void)
+{
+	struct udevice *stusb1600;
+	struct udevice *dwc2_udc_otg;
+	int ret;
+
+	if (!stusb1600_init(&stusb1600))
+		return stusb1600_cable_connected(stusb1600);

board/dhelectronics/dh_stm32mp1/board.c line 271

Quoted 10 lines
board/dhelectronics/dh_stm32mp1/board.c new file +10 -0
+
+	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
+					  DM_GET_DRIVER(dwc2_udc_otg),
+					  &dwc2_udc_otg);
+	if (!ret)
+		debug("dwc2_udc_otg init failed\n");
+
+	return dwc2_udc_B_session_valid(dwc2_udc_otg);
+}
+

If you don't have STUSB1600 (external usb typeC controller) All this part can dropped.

Quoted 513 lines
board/dhelectronics/dh_stm32mp1/board.c new file +7 -0
+#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11 #define
+STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
+
+int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char
+*name) {
+	if (!strcmp(name, "usb_dnl_dfu"))
+		put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev-
Quoted 1 line

idProduct);

board/dhelectronics/dh_stm32mp1/board.c new file +2 -0
+	else if (!strcmp(name, "usb_dnl_fastboot"))
+

put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,

board/dhelectronics/dh_stm32mp1/board.c new file +3 -0
+			      &dev->idProduct);
+	else
+		put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev-
Quoted 1 line

idProduct);

board/dhelectronics/dh_stm32mp1/board.c new file +91 -0
+
+	return 0;
+}
+
+#endif /* CONFIG_USB_GADGET */
+
+#ifdef CONFIG_LED
+static int get_led(struct udevice **dev, char *led_string) {
+	char *led_name;
+	int ret;
+
+	led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
+	if (!led_name) {
+		pr_debug("%s: could not find %s config string\n",
+			 __func__, led_string);
+		return -ENOENT;
+	}
+	ret = led_get_by_label(led_name, dev);
+	if (ret) {
+		debug("%s: get=%d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int setup_led(enum led_state_t cmd) {
+	struct udevice *dev;
+	int ret;
+
+	ret = get_led(&dev, "u-boot,boot-led");
+	if (ret)
+		return ret;
+
+	ret = led_set_state(dev, cmd);
+	return ret;
+}
+#endif
+
+static void __maybe_unused led_error_blink(u32 nb_blink) { #ifdef
+CONFIG_LED
+	int ret;
+	struct udevice *led;
+	u32 i;
+#endif
+
+	if (!nb_blink)
+		return;
+
+#ifdef CONFIG_LED
+	ret = get_led(&led, "u-boot,error-led");
+	if (!ret) {
+		/* make u-boot,error-led blinking */
+		/* if U32_MAX and 125ms interval, for 17.02 years */
+		for (i = 0; i < 2 * nb_blink; i++) {
+			led_set_state(led, LEDST_TOGGLE);
+			mdelay(125);
+			WATCHDOG_RESET();
+		}
+	}
+#endif
+
+	/* infinite: the boot process must be stopped */
+	if (nb_blink == U32_MAX)
+		hang();
+}
+
+static void sysconf_init(void)
+{
+#ifndef CONFIG_STM32MP1_TRUSTED
+	u8 *syscfg;
+#ifdef CONFIG_DM_REGULATOR
+	struct udevice *pwr_dev;
+	struct udevice *pwr_reg;
+	struct udevice *dev;
+	int ret;
+	u32 otp = 0;
+#endif
+	u32 bootr;
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	/* interconnect update : select master using the port 1 */
+	/* LTDC = AXI_M9 */
+	/* GPU  = AXI_M8 */
+	/* today information is hardcoded in U-Boot */
+	writel(BIT(9), syscfg + SYSCFG_ICNR);
+
+	/* disable Pull-Down for boot pin connected to VDD */
+	bootr = readl(syscfg + SYSCFG_BOOTR);
+	bootr &= ~(SYSCFG_BOOTR_BOOT_MASK <<

SYSCFG_BOOTR_BOOTPD_SHIFT);

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) <<

SYSCFG_BOOTR_BOOTPD_SHIFT;

board/dhelectronics/dh_stm32mp1/board.c new file +4 -0
+	writel(bootr, syscfg + SYSCFG_BOOTR);
+
+#ifdef CONFIG_DM_REGULATOR
+	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH,

QSPI

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX

selection.

board/dhelectronics/dh_stm32mp1/board.c new file +17 -0
+	 * The customer will have to disable this for low frequencies
+	 * or if AFMUX is selected but the function not used, typically for
+	 * TRACE. Otherwise, impact on power consumption.
+	 *
+	 * WARNING:
+	 *   enabling High Speed mode while VDD>2.7V
+	 *   with the OTP product_below_2v5 (OTP 18, BIT 13)
+	 *   erroneously set to 1 can damage the IC!
+	 *   => U-Boot set the register only if VDD < 2.7V (in DT)
+	 *      but this value need to be consistent with board design
+	 */
+	ret = uclass_get_device_by_driver(UCLASS_PMIC,
+					  DM_GET_DRIVER(stm32mp_pwr_pmic),
+					  &pwr_dev);
+	if (!ret) {
+		ret = uclass_get_device_by_driver(UCLASS_MISC,
+

DM_GET_DRIVER(stm32mp_bsec),

board/dhelectronics/dh_stm32mp1/board.c new file +19 -0
+						  &dev);
+		if (ret) {
+			pr_err("Can't find stm32mp_bsec driver\n");
+			return;
+		}
+
+		ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
+		if (ret > 0)
+			otp = otp & BIT(13);
+
+		/* get VDD = vdd-supply */
+		ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
+						  &pwr_reg);
+
+		/* check if VDD is Low Voltage */
+		if (!ret) {
+			if (regulator_get_value(pwr_reg) < 2700000) {
+				writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
+				       SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI

|

board/dhelectronics/dh_stm32mp1/board.c new file +7 -0
+				       SYSCFG_IOCTRLSETR_HSLVEN_ETH |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SPI,
+				       syscfg + SYSCFG_IOCTRLSETR);
+
+				if (!otp)
+					pr_err("product_below_2v5=0: HSLVEN

protected by HW\n");

board/dhelectronics/dh_stm32mp1/board.c new file +3 -0
+			} else {
+				if (otp)
+					pr_err("product_below_2v5=1: HSLVEN

update is destructive, no update as VDD>2.7V\n");

board/dhelectronics/dh_stm32mp1/board.c new file +11 -0
+			}
+		} else {
+			debug("VDD unknown");
+		}
+	}
+#endif
+
+	/* activate automatic I/O compensation
+	 * warning: need to ensure CSI enabled and ready in clock driver
+	 */
+	writel(SYSCFG_CMPENSETR_MPU_EN, syscfg +

SYSCFG_CMPENSETR);

board/dhelectronics/dh_stm32mp1/board.c new file +4 -0
+
+	while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
+		;
+	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);

#endif }

board/dhelectronics/dh_stm32mp1/board.c new file +53 -0
+
+/* board dependent setup after realloc */ int board_init(void) {
+	struct udevice *dev;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
+
+	/* probe all PINCTRL for hog */
+	for (uclass_first_device(UCLASS_PINCTRL, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("probe pincontrol = %s\n", dev->name);
+	}
+
+	board_key_check();
+
+#ifdef CONFIG_DM_REGULATOR
+	regulators_enable_boot_on(_DEBUG);
+#endif
+
+	sysconf_init();
+
+	if (CONFIG_IS_ENABLED(CONFIG_LED))
+		led_default_state();
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	char *boot_device;
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	const void *fdt_compat;
+	int fdt_compat_len;
+	int ret;
+	u32 otp;
+	struct udevice *dev;
+	char buf[10];
+
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len) {
+		if (strncmp(fdt_compat, "st,", 3) != 0)
+			env_set("board_name", fdt_compat);
+		else
+			env_set("board_name", fdt_compat + 3);
+	}
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev,

STM32_BSEC_SHADOW(BSEC_OTP_BOARD),

board/dhelectronics/dh_stm32mp1/board.c new file +88 -0
+				&otp, sizeof(otp));
+	if (!ret && otp) {
+		snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
+		env_set("board_id", buf);
+
+		snprintf(buf, sizeof(buf), "0x%04x",
+			 ((otp >> 8) & 0xF) - 1 + 0xA);
+		env_set("board_rev", buf);
+	}
+#endif
+
+	/* Check the boot-source to disable bootdelay */
+	boot_device = env_get("boot_device");
+	if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
+		env_set("bootdelay", "0");
+
+	return 0;
+}
+
+void board_quiesce_devices(void)
+{
+#ifdef CONFIG_LED
+	setup_led(LEDST_OFF);
+#endif
+}
+
+/* eth init function : weak called in eqos driver */ int
+board_interface_eth_init(struct udevice *dev,
+			     phy_interface_t interface_type) {
+	u8 *syscfg;
+	u32 value;
+	bool eth_clk_sel_reg = false;
+	bool eth_ref_clk_sel_reg = false;
+
+	/* Gigabit Ethernet 125MHz clock selection. */
+	eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
+
+	/* Ethernet 50Mhz RMII clock selection */
+	eth_ref_clk_sel_reg =
+		dev_read_bool(dev, "st,eth_ref_clk_sel");
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	if (!syscfg)
+		return -ENODEV;
+
+	switch (interface_type) {
+	case PHY_INTERFACE_MODE_MII:
+		value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+			SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_GMII:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
+		debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (eth_ref_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII |
+				SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII;
+		debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
+		debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
+		break;
+	default:
+		debug("%s: Do not manage %d interface\n",
+		      __func__, interface_type);
+		/* Do not manage others interfaces */
+		return -EINVAL;
+	}
+
+	/* clear and set ETH configuration bits */
+	writel(SYSCFG_PMCSETR_ETH_SEL_MASK |

SYSCFG_PMCSETR_ETH_SELMII |

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	       SYSCFG_PMCSETR_ETH_REF_CLK_SEL |

SYSCFG_PMCSETR_ETH_CLK_SEL,

board/dhelectronics/dh_stm32mp1/board.c new file +167 -0
+	       syscfg + SYSCFG_PMCCLRR);
+	writel(value, syscfg + SYSCFG_PMCSETR);
+
+	return 0;
+}
+
+enum env_location env_get_location(enum env_operation op, int prio) {
+	if (prio)
+		return ENVL_UNKNOWN;
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+	return ENVL_SPI_FLASH;
+#else
+	return ENVL_NOWHERE;
+#endif
+}
+
+#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
+
+#define MTDPARTS_LEN		256
+#define MTDIDS_LEN		128
+
+/**
+ * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
+ * If we need to access it before the env is relocated, then we need
+ * to use our own stack buffer. gd->env_buf will be too small.
+ *
+ * @param buf temporary buffer pointer MTDPARTS_LEN long
+ * @return mtdparts variable string, NULL if not found  */ static const
+char *env_get_mtdparts(const char *str, char *buf) {
+	if (gd->flags & GD_FLG_ENV_READY)
+		return env_get(str);
+	if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
+		return buf;
+
+	return NULL;
+}
+
+/**
+ * update the variables "mtdids" and "mtdparts" with content of
+mtdparts_<dev>  */ static void board_get_mtdparts(const char *dev,
+			       char *mtdids,
+			       char *mtdparts)
+{
+	char env_name[32] = "mtdparts_";
+	char tmp_mtdparts[MTDPARTS_LEN];
+	const char *tmp;
+
+	/* name of env variable to read = mtdparts_<dev> */
+	strcat(env_name, dev);
+	tmp = env_get_mtdparts(env_name, tmp_mtdparts);
+	if (tmp) {
+		/* mtdids: "<dev>=<dev>, ...." */
+		if (mtdids[0] != '\0')
+			strcat(mtdids, ",");
+		strcat(mtdids, dev);
+		strcat(mtdids, "=");
+		strcat(mtdids, dev);
+
+		/* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
+		if (mtdparts[0] != '\0')
+			strncat(mtdparts, ";", MTDPARTS_LEN);
+		else
+			strcat(mtdparts, "mtdparts=");
+		strncat(mtdparts, dev, MTDPARTS_LEN);
+		strncat(mtdparts, ":", MTDPARTS_LEN);
+		strncat(mtdparts, tmp, MTDPARTS_LEN);
+	}
+}
+
+void board_mtdparts_default(const char **mtdids, const char **mtdparts)
+{
+	struct udevice *dev;
+	static char parts[3 * MTDPARTS_LEN + 1];
+	static char ids[MTDIDS_LEN + 1];
+	static bool mtd_initialized;
+
+	if (mtd_initialized) {
+		*mtdids = ids;
+		*mtdparts = parts;
+		return;
+	}
+
+	memset(parts, 0, sizeof(parts));
+	memset(ids, 0, sizeof(ids));
+
+	/* probe all MTD devices */
+	for (uclass_first_device(UCLASS_MTD, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("mtd device = %s\n", dev->name);
+	}
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_mtdparts("nor0", ids, parts);
+
+	mtd_initialized = true;
+	*mtdids = ids;
+	*mtdparts = parts;
+	debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts); } #endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd) {
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_SET_DFU_ALT_INFO
+#define DFU_ALT_BUF_LEN SZ_1K
+
+static void board_get_alt_info(const char *dev, char *buff) {
+	char var_name[32] = "dfu_alt_info_";
+	int ret;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
+
+	/* name of env variable to read = dfu_alt_info_<dev> */
+	strcat(var_name, dev);
+	ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
+	if (ret) {
+		if (buff[0] != '\0')
+			strcat(buff, "&");
+		strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
+	}
+}
+
+void set_dfu_alt_info(char *interface, char *devstr) {
+	struct udevice *dev;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
+
+	if (env_get("dfu_alt_info"))
+		return;
+
+	memset(buf, 0, sizeof(buf));
+
+	/* probe all MTD devices */
+	mtd_probe_devices();
+
+	board_get_alt_info("ram", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 0, &dev))
+		board_get_alt_info("mmc0", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 1, &dev))
+		board_get_alt_info("mmc1", buf);
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_alt_info("nor0", buf);
+
+	env_set("dfu_alt_info", buf);
+	puts("DFU alt info setting: done\n");
+}
+#endif
+
+static void board_copro_image_process(ulong fw_image, size_t fw_size) {
+	int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
+
+	if (!rproc_is_initialized())
+		if (rproc_init()) {
+			printf("Remote Processor %d initialization failed\n",
+			       id);
+			return;
+		}
+
+	ret = rproc_load(id, fw_image, fw_size);
+	printf("Load Remote Processor %d with data at addr=0x%08lx %u

bytes:%s\n",

board/dhelectronics/dh_stm32mp1/board.c new file +9 -0
+	       id, fw_image, fw_size, ret ? " Failed!" : " Success!");
+
+	if (!ret) {
+		rproc_start(id);
+		env_set("copro_state", "booted");
+	}
+}
+
+U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO,

board_copro_image_process);

configs/stm32mp15_dhcom_basic_defconfig new file +0 -0
new file mode 100644
index 0000000000..e4f331a913

configs/stm32mp15_dhcom_basic_defconfig line 8

Quoted 8 lines
configs/stm32mp15_dhcom_basic_defconfig new file +8 -0
@@ -0,0 +1,140 @@
+CONFIG_ARM=y
+CONFIG_ARCH_STM32MP=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_ENV_SIZE=0x4000
+CONFIG_SPL=y
+CONFIG_TARGET_STM32MP1=y
+# CONFIG_TARGET_STM32MP157C_DK2 is not set

CONFIG_TARGET_DH_STM32MP1_PDK2=y

Quoted 128 lines
configs/stm32mp15_dhcom_basic_defconfig new file +46 -0
+CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y #
+CONFIG_ARMV7_VIRT is not set
+CONFIG_SPL_TEXT_BASE=0x2FFC2500
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+# CONFIG_BOOTSTAGE is not set
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_MTD_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
+CONFIG_SYS_PROMPT="STM32MP> "
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_REMOTEPROC=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_MTDPARTS=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-

extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"

configs/stm32mp15_dhcom_basic_defconfig new file +38 -0
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=10000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_IP_DEFRAG=y
+CONFIG_TFTP_BLOCKSIZE=1536
+CONFIG_STM32_ADC=y
+CONFIG_SPL_BLOCK_CACHE=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_VIRT=y
+CONFIG_DM_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_STM32F7=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_STM32_IPCC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_STM32_SDMMC2=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set

CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y
CONFIG_DWC_ETH_QOS=y

configs/stm32mp15_dhcom_basic_defconfig new file +5 -0
+CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y #
+CONFIG_SPL_PINCTRL_FULL is not set CONFIG_PINCTRL_STMFX=y
+CONFIG_DM_PMIC=y # CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_PMIC_STPMIC1=y CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y

CONFIG_DM_REGULATOR_STM32_VREFBUF=y

configs/stm32mp15_dhcom_basic_defconfig new file +32 -1
+CONFIG_DM_REGULATOR_STPMIC1=y
+CONFIG_REMOTEPROC_STM32_COPRO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_STM32=y
+CONFIG_SERIAL_RX_BUFFER=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_STM32_QSPI=y
+CONFIG_STM32_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="dh"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0483
+CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_DM_VIDEO=y
+CONFIG_BACKLIGHT_GPIO=y
+CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
+CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
+CONFIG_VIDEO_STM32=y
+CONFIG_VIDEO_STM32_DSI=y
+CONFIG_VIDEO_STM32_MAX_XRES=1280
+CONFIG_VIDEO_STM32_MAX_YRES=800
+CONFIG_LZO=y
+CONFIG_FDT_FIXUP_PARTITIONS=y
--
Quoted 2 lines

2.24.1

Regards

Patrick

#19 lore raw

PATCH 5/5 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Hi Marek,

Quoted 15 lines

From: Patrick DELAUNAY
Sent: lundi 13 janvier 2020 15:05

Hi Marek,

Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

---

For information, I merge the serie, except this patch 5/5 on master brach and I sent a pull request for u-boot-stm32-20200117.

For this patch, I propose a rebase and also many modification liked to my previous remark (I remove ST only parts for stboard command, and also led and key management) .

This proposal is present in the branch https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/next

	https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/db48e11b1eccf23f3f9ba26e886a798e74df6a01

your initial patch is in applied https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh

Can you test the "next" branch and check the difference with your initial patch ( applied in dh branch
https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh
=> https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/0ab3ce72f82b946ac0924dfcdc082792f325eb68 )

I hope that I don't remove something really present on the SOM.

If you are OK, can you send a V2 version with the "next" branch content and I will integrate it in master branch for next pull request.

Thanks,

Patrick

Quoted 1,828 lines
Quoted 179 lines
 arch/arm/dts/Makefile                         |   1 +
 .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
 arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
 arch/arm/mach-stm32mp/Kconfig                 |   1 +
 board/dhelectronics/dh_stm32mp1/Kconfig       |  25 +
 board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
 board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
 board/dhelectronics/dh_stm32mp1/board.c       | 777 ++++++++++++++++++
 configs/stm32mp15_dhcom_basic_defconfig       | 140 ++++
 11 files changed, 1675 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
 create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
 create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
 create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
 create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
 create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
arch/arm/dts/Makefile index renamed from arch/arm/dts/Makefile +0 -0

983e235f44..82489bc09c 100644

arch/arm/dts/Makefile +1 -0
@@ -859,6 +859,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_TARGET_STM32MP1) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157c-dhcom-pdk2-u-boot.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb
arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts new file +6 -0
new file mode 100644
index 0000000000..fd99988570
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include "stm32mp157c-dhcom-pdk2.dts"
+#include "stm32mp157c-dhcom-u-boot.dtsi"
arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +8 -0
new file mode 100644
index 0000000000..05aa545f55
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include "stm32mp157c-dhcom.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C DHCOM Premium

Developer Kit (2)";

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +48 -0
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth_ref_clk_sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy at 1 {
+			reg = <1>;
+		};
+	};
+};
+
+&pinctrl {
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /*

ETH1_RMII_TXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('G', 14, AF11)>, /*

ETH1_RMII_TXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('B', 11, AF11)>, /*

ETH1_RMII_TX_EN */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 1, AF0)>,   /*

ETH1_RMII_REF_CLK */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO

*/

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC

*/

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +6 -0
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /*

ETH1_RMII_RXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 5, AF11)>,  /*

ETH1_RMII_RXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 7, AF11)>;  /*

ETH1_RMII_CRS_DV */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +7 -0
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /*

ETH1_RMII_TXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('G', 14, ANALOG)>, /*

ETH1_RMII_TXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('B', 11, ANALOG)>, /*

ETH1_RMII_TX_EN */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /*

ETH1_MDIO */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /*

ETH1_MDC */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /*

ETH1_RMII_RXD0 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /*

ETH1_RMII_RXD1 */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /*

ETH1_RMII_REF_CLK */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +1 -0
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /*

ETH1_RMII_CRS_DV */

arch/arm/dts/stm32mp157c-dhcom-pdk2.dts new file +3 -0
+		};
+	};
+};
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +12 -0
new file mode 100644
index 0000000000..320912edd8
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp157-u-boot.dtsi"
+#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
+
+/ {
+	aliases {
+		i2c1 = &i2c2;
+		i2c3 = &i2c4;

arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi line 22

Quoted 10 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +10 -0
+		i2c4 = &i2c5;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		spi0 = &qspi;
+		usb0 = &usbotg_hs;
+	};
+
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";

Excpet if I miss something, You have no led on your board (named = "heartbeat" or "error" ) This 2 line can be remove I think

Quoted 6 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +6 -0
+		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+	};
+
+	led {
+		red {

arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi line 39

Quoted 10 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +10 -0
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+
+		blue {
+			default-state = "on";
+		};
+	};

This blue overridde can be remove I think.

Quoted 600 lines
arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi new file +199 -0
+};
+
+&i2c4 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&flash0 {
+	u-boot,dm-spl;
+};
+
+&qspi {
+	u-boot,dm-spl;
+};
+
+&qspi_clk_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk1_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk2_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_PLL4P
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4Q
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll at 0 {
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll at 1 {
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll at 2 {
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
+	pll4: st,pll at 3 {
+		cfg = < 1 49 11 11 11 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
(quoted diff) +0 -0

b/arch/arm/dts/stm32mp157c- dhcom.dtsi new file mode 100644 index 0000000000..96661ae783

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +228 -0
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019 Marek Vasut <[email protected]>  */ /dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&dcmi {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_a>;
+	pinctrl-1 = <&dcmi_sleep_pins_a>;
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	status = "okay";
+};
+
+&pwr {
+	pwr-regulators {
+		vdd-supply = <&vdd>;
+		vdd_3v3_usbfs-supply = <&vdd_usb>;
+	};
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a

&qspi_bk2_sleep_pins_a>;

arch/arm/dts/stm32mp157c-dhcom.dtsi new file +149 -0
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	flash1: mx66l51235l at 1 {
+		compatible = "jedec,spi-nor";
+		reg = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,sig-dir;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	status = "disabled";
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 1 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	timer at 5 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 7 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
(quoted diff) +0 -0

b/arch/arm/mach-stm32mp/Kconfig index ae28f6e206..1aa5f8a122 100644

arch/arm/mach-stm32mp/Kconfig +1 -0
@@ -147,5 +147,6 @@ config DEBUG_UART_CLOCK  endif
 
 source "board/st/stm32mp1/Kconfig"
+source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
 endif
board/dhelectronics/dh_stm32mp1/Kconfig new file +0 -0
new file mode 100644
index 0000000000..e751a3e5ed

board/dhelectronics/dh_stm32mp1/Kconfig line 3

Quoted 3 lines
board/dhelectronics/dh_stm32mp1/Kconfig new file +3 -0
@@ -0,0 +1,25 @@
+config TARGET_DH_STM32MP1_PDK2
+	bool "support of DH STM32MP1 PDK2"
+	default y

Avoid set default y here....
to avoid to activate this config for ST board.

In fact it should be a choice between the 2 targets
- TARGET_DH_STM32MP1_PDK2
- TARGET_ST_STM32MP1

Quoted 43 lines
board/dhelectronics/dh_stm32mp1/Kconfig new file +22 -0
+
+if TARGET_DH_STM32MP1_PDK2
+
+config SYS_BOARD
+	default "dh_stm32mp1"
+
+config SYS_VENDOR
+	default "dhelectronics"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET_REDUND
+	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
+
+endif
board/dhelectronics/dh_stm32mp1/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..38f54a3da4
@@ -0,0 +1,7 @@
+DH_STM32MP1_PDK2 BOARD
+M:	Marek Vasut <[email protected]>
+S:	Maintained
+F:	arch/arm/dts/stm32mp157c-dhcom*
+F:	board/dhelectronics/dh_stm32mp1/
+F:	configs/stm32mp15_dhcom_basic_defconfig
+F:	include/configs/stm32mp1.h
board/dhelectronics/dh_stm32mp1/Makefile new file +0 -0
new file mode 100644
index 0000000000..a9d28218ef

board/dhelectronics/dh_stm32mp1/Makefile line 8

Quoted 8 lines
board/dhelectronics/dh_stm32mp1/Makefile new file +8 -0
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause # # Copyright (C)
+2018, STMicroelectronics - All Rights Reserved #
+
+ifdef CONFIG_SPL_BUILD
+obj-y += ../../st/stm32mp1/spl.o
+else
+obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o endif
+

I don't think you wee to support the command STMicroelctronics board (ref MBxxxx).
it is only a internal command for ST : save/read board id in OTP.

Quoted 150 lines
board/dhelectronics/dh_stm32mp1/Makefile new file +1 -0
+obj-y += ../../st/stm32mp1/board.o board.o
board/dhelectronics/dh_stm32mp1/board.c new file +94 -0
new file mode 100644
index 0000000000..54cc3b7587
@@ -0,0 +1,777 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved  */
+
+#include <common.h>
+#include <adc.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <bootm.h>
+#include <clk.h>
+#include <config.h>
+#include <dm.h>
+#include <dm/device.h>
+#include <dm/uclass.h>
+#include <env.h>
+#include <env_internal.h>
+#include <g_dnl.h>
+#include <generic-phy.h>
+#include <i2c.h>
+#include <i2c_eeprom.h>
+#include <init.h>
+#include <led.h>
+#include <memalign.h>
+#include <misc.h>
+#include <mtd.h>
+#include <mtd_node.h>
+#include <netdev.h>
+#include <phy.h>
+#include <power/regulator.h>
+#include <remoteproc.h>
+#include <reset.h>
+#include <syscon.h>
+#include <usb.h>
+#include <usb/dwc2_udc.h>
+#include <watchdog.h>
+
+/* SYSCFG registers */
+#define SYSCFG_BOOTR		0x00
+#define SYSCFG_PMCSETR		0x04
+#define SYSCFG_IOCTRLSETR	0x18
+#define SYSCFG_ICNR		0x1C
+#define SYSCFG_CMPCR		0x20
+#define SYSCFG_CMPENSETR	0x24
+#define SYSCFG_PMCCLRR		0x44
+
+#define SYSCFG_BOOTR_BOOT_MASK		GENMASK(2, 0)
+#define SYSCFG_BOOTR_BOOTPD_SHIFT	4
+
+#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE		BIT(0)
+#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI	BIT(1)
+#define SYSCFG_IOCTRLSETR_HSLVEN_ETH		BIT(2)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC		BIT(3)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SPI		BIT(4)
+
+#define SYSCFG_CMPCR_SW_CTRL		BIT(1)
+#define SYSCFG_CMPCR_READY		BIT(8)
+
+#define SYSCFG_CMPENSETR_MPU_EN		BIT(0)
+
+#define SYSCFG_PMCSETR_ETH_CLK_SEL	BIT(16)
+#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL	BIT(17)
+
+#define SYSCFG_PMCSETR_ETH_SELMII	BIT(20)
+
+#define SYSCFG_PMCSETR_ETH_SEL_MASK	GENMASK(23, 21)
+#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII	0
+#define SYSCFG_PMCSETR_ETH_SEL_RGMII	BIT(21)
+#define SYSCFG_PMCSETR_ETH_SEL_RMII	BIT(23)
+
+/*
+ * Get a global data pointer
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+int setup_mac_address(void)
+{
+	struct udevice *dev;
+	ofnode eeprom;
+	unsigned char enetaddr[6];
+	int ret;
+
+	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
+	if (ret)	/* ethaddr is already set */
+		return 0;
+
+	eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
+	if (!ofnode_valid(eeprom)) {
+		printf("Invalid hardware path to EEPROM!\n");
+		return -ENODEV;
+	}
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom,

&dev);

board/dhelectronics/dh_stm32mp1/board.c new file +46 -0
+	if (ret) {
+		printf("Cannot find EEPROM!\n");
+		return ret;
+	}
+
+	ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
+	if (ret) {
+		printf("Error reading configuration EEPROM!\n");
+		return ret;
+	}
+
+	if (is_valid_ethaddr(enetaddr))
+		eth_env_set_enetaddr("ethaddr", enetaddr);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	int ret;
+	char *mode;
+	u32 otp;
+	struct udevice *dev;
+	const char *fdt_compat;
+	int fdt_compat_len;
+
+	if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
+		mode = "trusted with OP-TEE";
+	else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
+		mode = "trusted";
+	else
+		mode = "basic";
+
+	printf("Board: stm32mp1 in %s mode", mode);
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len)
+		printf(" (%s)", fdt_compat);
+	puts("\n");
+
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev,

STM32_BSEC_SHADOW(BSEC_OTP_BOARD),

board/dhelectronics/dh_stm32mp1/board.c line 149

Quoted 8 lines
board/dhelectronics/dh_stm32mp1/board.c new file +8 -0
+				&otp, sizeof(otp));
+	if (ret > 0 && otp) {
+		printf("Board: MB%04x Var%d Rev.%c-%02d\n",
+		       otp >> 16,
+		       (otp >> 12) & 0xF,
+		       ((otp >> 8) & 0xF) - 1 + 'A',
+		       otp & 0xF);
+	}

This part (read OTP / / display MBxxx ) can be dropped for your board (it is a ST specific part).

Quoted 41 lines
board/dhelectronics/dh_stm32mp1/board.c new file +41 -0
+	return 0;
+}
+
+static void board_key_check(void)
+{
+#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
+	ofnode node;
+	struct gpio_desc gpio;
+	enum forced_boot_mode boot_mode = BOOT_NORMAL;
+
+	node = ofnode_path("/config");
+	if (!ofnode_valid(node)) {
+		debug("%s: no /config node?\n", __func__);
+		return;
+	}
+#ifdef CONFIG_FASTBOOT
+	if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,fastboot-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("Fastboot key pressed, ");
+			boot_mode = BOOT_FASTBOOT;
+		}
+
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+#ifdef CONFIG_CMD_STM32PROG
+	if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,stm32prog-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("STM32Programmer key pressed, ");
+			boot_mode = BOOT_STM32PROG;
+		}
+		dm_gpio_free(NULL, &gpio);
+	}

board/dhelectronics/dh_stm32mp1/board.c line 201

Quoted 10 lines
board/dhelectronics/dh_stm32mp1/board.c new file +10 -0
+#endif
+
+	if (boot_mode != BOOT_NORMAL) {
+		puts("entering download mode...\n");
+		clrsetbits_le32(TAMP_BOOT_CONTEXT,
+				TAMP_BOOT_FORCED_MASK,
+				boot_mode);
+	}
+#endif
+}

Do you support GPIO key press on GPAIOA14 / 15 (as it is done in ST boards EV1 : DK1 / DK2) If no all this function can be dropped.

Quoted 59 lines

+#if defined(CONFIG_USB_GADGET) &&
defined(CONFIG_USB_GADGET_DWC2_OTG)

board/dhelectronics/dh_stm32mp1/board.c new file +25 -0
+
+/* STMicroelectronics STUSB1600 Type-C controller */
+#define STUSB1600_CC_CONNECTION_STATUS		0x0E
+
+/* STUSB1600_CC_CONNECTION_STATUS bitfields */
+#define STUSB1600_CC_ATTACH			BIT(0)
+
+static int stusb1600_init(struct udevice **dev_stusb1600) {
+	ofnode node;
+	struct udevice *dev, *bus;
+	int ret;
+	u32 chip_addr;
+
+	*dev_stusb1600 = NULL;
+
+	/* if node stusb1600 is present, means DK1 or DK2 board */
+	node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
+	if (!ofnode_valid(node))
+		return -ENODEV;
+
+	ret = ofnode_read_u32(node, "reg", &chip_addr);
+	if (ret)
+		return -EINVAL;
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C,

ofnode_get_parent(node),

board/dhelectronics/dh_stm32mp1/board.c new file +17 -0
+					  &bus);
+	if (ret) {
+		printf("bus for stusb1600 not found\n");
+		return -ENODEV;
+	}
+
+	ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
+	if (!ret)
+		*dev_stusb1600 = dev;
+
+	return ret;
+}
+
+static int stusb1600_cable_connected(struct udevice *dev) {
+	u8 status;
+
+	if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status,

1))

board/dhelectronics/dh_stm32mp1/board.c new file +13 -0
+		return 0;
+
+	return status & STUSB1600_CC_ATTACH; }
+
+#include <usb/dwc2_udc.h>
+int g_dnl_board_usb_cable_connected(void)
+{
+	struct udevice *stusb1600;
+	struct udevice *dwc2_udc_otg;
+	int ret;
+
+	if (!stusb1600_init(&stusb1600))
+		return stusb1600_cable_connected(stusb1600);

board/dhelectronics/dh_stm32mp1/board.c line 271

Quoted 10 lines
board/dhelectronics/dh_stm32mp1/board.c new file +10 -0
+
+	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
+					  DM_GET_DRIVER(dwc2_udc_otg),
+					  &dwc2_udc_otg);
+	if (!ret)
+		debug("dwc2_udc_otg init failed\n");
+
+	return dwc2_udc_B_session_valid(dwc2_udc_otg);
+}
+

If you don't have STUSB1600 (external usb typeC controller) All this part can dropped.

Quoted 512 lines
board/dhelectronics/dh_stm32mp1/board.c new file +7 -0
+#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11 #define
+STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
+
+int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char
+*name) {
+	if (!strcmp(name, "usb_dnl_dfu"))
+		put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev-
Quoted 1 line

idProduct);

board/dhelectronics/dh_stm32mp1/board.c new file +2 -0
+	else if (!strcmp(name, "usb_dnl_fastboot"))
+

put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,

board/dhelectronics/dh_stm32mp1/board.c new file +3 -0
+			      &dev->idProduct);
+	else
+		put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev-
Quoted 1 line

idProduct);

board/dhelectronics/dh_stm32mp1/board.c new file +91 -0
+
+	return 0;
+}
+
+#endif /* CONFIG_USB_GADGET */
+
+#ifdef CONFIG_LED
+static int get_led(struct udevice **dev, char *led_string) {
+	char *led_name;
+	int ret;
+
+	led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
+	if (!led_name) {
+		pr_debug("%s: could not find %s config string\n",
+			 __func__, led_string);
+		return -ENOENT;
+	}
+	ret = led_get_by_label(led_name, dev);
+	if (ret) {
+		debug("%s: get=%d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int setup_led(enum led_state_t cmd) {
+	struct udevice *dev;
+	int ret;
+
+	ret = get_led(&dev, "u-boot,boot-led");
+	if (ret)
+		return ret;
+
+	ret = led_set_state(dev, cmd);
+	return ret;
+}
+#endif
+
+static void __maybe_unused led_error_blink(u32 nb_blink) { #ifdef
+CONFIG_LED
+	int ret;
+	struct udevice *led;
+	u32 i;
+#endif
+
+	if (!nb_blink)
+		return;
+
+#ifdef CONFIG_LED
+	ret = get_led(&led, "u-boot,error-led");
+	if (!ret) {
+		/* make u-boot,error-led blinking */
+		/* if U32_MAX and 125ms interval, for 17.02 years */
+		for (i = 0; i < 2 * nb_blink; i++) {
+			led_set_state(led, LEDST_TOGGLE);
+			mdelay(125);
+			WATCHDOG_RESET();
+		}
+	}
+#endif
+
+	/* infinite: the boot process must be stopped */
+	if (nb_blink == U32_MAX)
+		hang();
+}
+
+static void sysconf_init(void)
+{
+#ifndef CONFIG_STM32MP1_TRUSTED
+	u8 *syscfg;
+#ifdef CONFIG_DM_REGULATOR
+	struct udevice *pwr_dev;
+	struct udevice *pwr_reg;
+	struct udevice *dev;
+	int ret;
+	u32 otp = 0;
+#endif
+	u32 bootr;
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	/* interconnect update : select master using the port 1 */
+	/* LTDC = AXI_M9 */
+	/* GPU  = AXI_M8 */
+	/* today information is hardcoded in U-Boot */
+	writel(BIT(9), syscfg + SYSCFG_ICNR);
+
+	/* disable Pull-Down for boot pin connected to VDD */
+	bootr = readl(syscfg + SYSCFG_BOOTR);
+	bootr &= ~(SYSCFG_BOOTR_BOOT_MASK <<

SYSCFG_BOOTR_BOOTPD_SHIFT);

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) <<

SYSCFG_BOOTR_BOOTPD_SHIFT;

board/dhelectronics/dh_stm32mp1/board.c new file +4 -0
+	writel(bootr, syscfg + SYSCFG_BOOTR);
+
+#ifdef CONFIG_DM_REGULATOR
+	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH,

QSPI

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX

selection.

board/dhelectronics/dh_stm32mp1/board.c new file +17 -0
+	 * The customer will have to disable this for low frequencies
+	 * or if AFMUX is selected but the function not used, typically for
+	 * TRACE. Otherwise, impact on power consumption.
+	 *
+	 * WARNING:
+	 *   enabling High Speed mode while VDD>2.7V
+	 *   with the OTP product_below_2v5 (OTP 18, BIT 13)
+	 *   erroneously set to 1 can damage the IC!
+	 *   => U-Boot set the register only if VDD < 2.7V (in DT)
+	 *      but this value need to be consistent with board design
+	 */
+	ret = uclass_get_device_by_driver(UCLASS_PMIC,
+					  DM_GET_DRIVER(stm32mp_pwr_pmic),
+					  &pwr_dev);
+	if (!ret) {
+		ret = uclass_get_device_by_driver(UCLASS_MISC,
+

DM_GET_DRIVER(stm32mp_bsec),

board/dhelectronics/dh_stm32mp1/board.c new file +19 -0
+						  &dev);
+		if (ret) {
+			pr_err("Can't find stm32mp_bsec driver\n");
+			return;
+		}
+
+		ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
+		if (ret > 0)
+			otp = otp & BIT(13);
+
+		/* get VDD = vdd-supply */
+		ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
+						  &pwr_reg);
+
+		/* check if VDD is Low Voltage */
+		if (!ret) {
+			if (regulator_get_value(pwr_reg) < 2700000) {
+				writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
+				       SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI

|

board/dhelectronics/dh_stm32mp1/board.c new file +7 -0
+				       SYSCFG_IOCTRLSETR_HSLVEN_ETH |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SPI,
+				       syscfg + SYSCFG_IOCTRLSETR);
+
+				if (!otp)
+					pr_err("product_below_2v5=0: HSLVEN

protected by HW\n");

board/dhelectronics/dh_stm32mp1/board.c new file +3 -0
+			} else {
+				if (otp)
+					pr_err("product_below_2v5=1: HSLVEN

update is destructive, no update as VDD>2.7V\n");

board/dhelectronics/dh_stm32mp1/board.c new file +11 -0
+			}
+		} else {
+			debug("VDD unknown");
+		}
+	}
+#endif
+
+	/* activate automatic I/O compensation
+	 * warning: need to ensure CSI enabled and ready in clock driver
+	 */
+	writel(SYSCFG_CMPENSETR_MPU_EN, syscfg +

SYSCFG_CMPENSETR);

board/dhelectronics/dh_stm32mp1/board.c new file +4 -0
+
+	while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
+		;
+	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);

#endif }

board/dhelectronics/dh_stm32mp1/board.c new file +53 -0
+
+/* board dependent setup after realloc */ int board_init(void) {
+	struct udevice *dev;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
+
+	/* probe all PINCTRL for hog */
+	for (uclass_first_device(UCLASS_PINCTRL, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("probe pincontrol = %s\n", dev->name);
+	}
+
+	board_key_check();
+
+#ifdef CONFIG_DM_REGULATOR
+	regulators_enable_boot_on(_DEBUG);
+#endif
+
+	sysconf_init();
+
+	if (CONFIG_IS_ENABLED(CONFIG_LED))
+		led_default_state();
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	char *boot_device;
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	const void *fdt_compat;
+	int fdt_compat_len;
+	int ret;
+	u32 otp;
+	struct udevice *dev;
+	char buf[10];
+
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len) {
+		if (strncmp(fdt_compat, "st,", 3) != 0)
+			env_set("board_name", fdt_compat);
+		else
+			env_set("board_name", fdt_compat + 3);
+	}
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev,

STM32_BSEC_SHADOW(BSEC_OTP_BOARD),

board/dhelectronics/dh_stm32mp1/board.c new file +88 -0
+				&otp, sizeof(otp));
+	if (!ret && otp) {
+		snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
+		env_set("board_id", buf);
+
+		snprintf(buf, sizeof(buf), "0x%04x",
+			 ((otp >> 8) & 0xF) - 1 + 0xA);
+		env_set("board_rev", buf);
+	}
+#endif
+
+	/* Check the boot-source to disable bootdelay */
+	boot_device = env_get("boot_device");
+	if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
+		env_set("bootdelay", "0");
+
+	return 0;
+}
+
+void board_quiesce_devices(void)
+{
+#ifdef CONFIG_LED
+	setup_led(LEDST_OFF);
+#endif
+}
+
+/* eth init function : weak called in eqos driver */ int
+board_interface_eth_init(struct udevice *dev,
+			     phy_interface_t interface_type) {
+	u8 *syscfg;
+	u32 value;
+	bool eth_clk_sel_reg = false;
+	bool eth_ref_clk_sel_reg = false;
+
+	/* Gigabit Ethernet 125MHz clock selection. */
+	eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
+
+	/* Ethernet 50Mhz RMII clock selection */
+	eth_ref_clk_sel_reg =
+		dev_read_bool(dev, "st,eth_ref_clk_sel");
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	if (!syscfg)
+		return -ENODEV;
+
+	switch (interface_type) {
+	case PHY_INTERFACE_MODE_MII:
+		value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+			SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_GMII:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
+		debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (eth_ref_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII |
+				SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII;
+		debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
+		debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
+		break;
+	default:
+		debug("%s: Do not manage %d interface\n",
+		      __func__, interface_type);
+		/* Do not manage others interfaces */
+		return -EINVAL;
+	}
+
+	/* clear and set ETH configuration bits */
+	writel(SYSCFG_PMCSETR_ETH_SEL_MASK |

SYSCFG_PMCSETR_ETH_SELMII |

board/dhelectronics/dh_stm32mp1/board.c new file +1 -0
+	       SYSCFG_PMCSETR_ETH_REF_CLK_SEL |

SYSCFG_PMCSETR_ETH_CLK_SEL,

board/dhelectronics/dh_stm32mp1/board.c new file +166 -0
+	       syscfg + SYSCFG_PMCCLRR);
+	writel(value, syscfg + SYSCFG_PMCSETR);
+
+	return 0;
+}
+
+enum env_location env_get_location(enum env_operation op, int prio) {
+	if (prio)
+		return ENVL_UNKNOWN;
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+	return ENVL_SPI_FLASH;
+#else
+	return ENVL_NOWHERE;
+#endif
+}
+
+#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
+
+#define MTDPARTS_LEN		256
+#define MTDIDS_LEN		128
+
+/**
+ * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
+ * If we need to access it before the env is relocated, then we need
+ * to use our own stack buffer. gd->env_buf will be too small.
+ *
+ * @param buf temporary buffer pointer MTDPARTS_LEN long
+ * @return mtdparts variable string, NULL if not found  */ static
+const char *env_get_mtdparts(const char *str, char *buf) {
+	if (gd->flags & GD_FLG_ENV_READY)
+		return env_get(str);
+	if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
+		return buf;
+
+	return NULL;
+}
+
+/**
+ * update the variables "mtdids" and "mtdparts" with content of
+mtdparts_<dev>  */ static void board_get_mtdparts(const char *dev,
+			       char *mtdids,
+			       char *mtdparts)
+{
+	char env_name[32] = "mtdparts_";
+	char tmp_mtdparts[MTDPARTS_LEN];
+	const char *tmp;
+
+	/* name of env variable to read = mtdparts_<dev> */
+	strcat(env_name, dev);
+	tmp = env_get_mtdparts(env_name, tmp_mtdparts);
+	if (tmp) {
+		/* mtdids: "<dev>=<dev>, ...." */
+		if (mtdids[0] != '\0')
+			strcat(mtdids, ",");
+		strcat(mtdids, dev);
+		strcat(mtdids, "=");
+		strcat(mtdids, dev);
+
+		/* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
+		if (mtdparts[0] != '\0')
+			strncat(mtdparts, ";", MTDPARTS_LEN);
+		else
+			strcat(mtdparts, "mtdparts=");
+		strncat(mtdparts, dev, MTDPARTS_LEN);
+		strncat(mtdparts, ":", MTDPARTS_LEN);
+		strncat(mtdparts, tmp, MTDPARTS_LEN);
+	}
+}
+
+void board_mtdparts_default(const char **mtdids, const char
+**mtdparts) {
+	struct udevice *dev;
+	static char parts[3 * MTDPARTS_LEN + 1];
+	static char ids[MTDIDS_LEN + 1];
+	static bool mtd_initialized;
+
+	if (mtd_initialized) {
+		*mtdids = ids;
+		*mtdparts = parts;
+		return;
+	}
+
+	memset(parts, 0, sizeof(parts));
+	memset(ids, 0, sizeof(ids));
+
+	/* probe all MTD devices */
+	for (uclass_first_device(UCLASS_MTD, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("mtd device = %s\n", dev->name);
+	}
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_mtdparts("nor0", ids, parts);
+
+	mtd_initialized = true;
+	*mtdids = ids;
+	*mtdparts = parts;
+	debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts); }
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd) {
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_SET_DFU_ALT_INFO
+#define DFU_ALT_BUF_LEN SZ_1K
+
+static void board_get_alt_info(const char *dev, char *buff) {
+	char var_name[32] = "dfu_alt_info_";
+	int ret;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
+
+	/* name of env variable to read = dfu_alt_info_<dev> */
+	strcat(var_name, dev);
+	ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
+	if (ret) {
+		if (buff[0] != '\0')
+			strcat(buff, "&");
+		strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
+	}
+}
+
+void set_dfu_alt_info(char *interface, char *devstr) {
+	struct udevice *dev;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
+
+	if (env_get("dfu_alt_info"))
+		return;
+
+	memset(buf, 0, sizeof(buf));
+
+	/* probe all MTD devices */
+	mtd_probe_devices();
+
+	board_get_alt_info("ram", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 0, &dev))
+		board_get_alt_info("mmc0", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 1, &dev))
+		board_get_alt_info("mmc1", buf);
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_alt_info("nor0", buf);
+
+	env_set("dfu_alt_info", buf);
+	puts("DFU alt info setting: done\n"); } #endif
+
+static void board_copro_image_process(ulong fw_image, size_t fw_size) {
+	int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
+
+	if (!rproc_is_initialized())
+		if (rproc_init()) {
+			printf("Remote Processor %d initialization failed\n",
+			       id);
+			return;
+		}
+
+	ret = rproc_load(id, fw_image, fw_size);
+	printf("Load Remote Processor %d with data at addr=0x%08lx %u

bytes:%s\n",

board/dhelectronics/dh_stm32mp1/board.c new file +9 -0
+	       id, fw_image, fw_size, ret ? " Failed!" : " Success!");
+
+	if (!ret) {
+		rproc_start(id);
+		env_set("copro_state", "booted");
+	}
+}
+
+U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO,

board_copro_image_process);

configs/stm32mp15_dhcom_basic_defconfig new file +0 -0
new file mode 100644
index 0000000000..e4f331a913

configs/stm32mp15_dhcom_basic_defconfig line 8

Quoted 8 lines
configs/stm32mp15_dhcom_basic_defconfig new file +8 -0
@@ -0,0 +1,140 @@
+CONFIG_ARM=y
+CONFIG_ARCH_STM32MP=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_ENV_SIZE=0x4000
+CONFIG_SPL=y
+CONFIG_TARGET_STM32MP1=y
+# CONFIG_TARGET_STM32MP157C_DK2 is not set

CONFIG_TARGET_DH_STM32MP1_PDK2=y

Quoted 46 lines
configs/stm32mp15_dhcom_basic_defconfig new file +46 -0
+CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y #
+CONFIG_ARMV7_VIRT is not set
+CONFIG_SPL_TEXT_BASE=0x2FFC2500
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+# CONFIG_BOOTSTAGE is not set
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_MTD_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
+CONFIG_SYS_PROMPT="STM32MP> "
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_REMOTEPROC=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_MTDPARTS=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-
Quoted 2 lines

extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-

parents hwlocks"

Quoted 38 lines
configs/stm32mp15_dhcom_basic_defconfig new file +38 -0
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=10000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_IP_DEFRAG=y
+CONFIG_TFTP_BLOCKSIZE=1536
+CONFIG_STM32_ADC=y
+CONFIG_SPL_BLOCK_CACHE=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_VIRT=y
+CONFIG_DM_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_STM32F7=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_STM32_IPCC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_STM32_SDMMC2=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
Quoted 4 lines

CONFIG_SPI_FLASH_MTD=y +CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y CONFIG_DWC_ETH_QOS=y
+CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y

#

Quoted 38 lines
configs/stm32mp15_dhcom_basic_defconfig new file +4 -0
+CONFIG_SPL_PINCTRL_FULL is not set CONFIG_PINCTRL_STMFX=y
+CONFIG_DM_PMIC=y # CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_PMIC_STPMIC1=y CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y

CONFIG_DM_REGULATOR_STM32_VREFBUF=y

configs/stm32mp15_dhcom_basic_defconfig new file +32 -1
+CONFIG_DM_REGULATOR_STPMIC1=y
+CONFIG_REMOTEPROC_STM32_COPRO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_STM32=y
+CONFIG_SERIAL_RX_BUFFER=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_STM32_QSPI=y
+CONFIG_STM32_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="dh"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0483
+CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_DM_VIDEO=y
+CONFIG_BACKLIGHT_GPIO=y
+CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
+CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
+CONFIG_VIDEO_STM32=y
+CONFIG_VIDEO_STM32_DSI=y
+CONFIG_VIDEO_STM32_MAX_XRES=1280
+CONFIG_VIDEO_STM32_MAX_YRES=800
+CONFIG_LZO=y
+CONFIG_FDT_FIXUP_PARTITIONS=y
--
Quoted 2 lines

2.24.1

Regards

Patrick

#20 lore raw

PATCH 5/5 ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Quoted 1 line · Patrick DELAUNAY

Hi Marek,

Hi,

Quoted 27 lines
Quoted 15 lines

From: Patrick DELAUNAY
Sent: lundi 13 janvier 2020 15:05

Hi Marek,

Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP157C and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

---

For information, I merge the serie, except this patch 5/5 on master brach and I sent a pull request for u-boot-stm32-20200117.

For this patch, I propose a rebase and also many modification liked to my previous remark (I remove ST only parts for stboard command, and also led and key management) .

This proposal is present in the branch https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/next

	https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/db48e11b1eccf23f3f9ba26e886a798e74df6a01

your initial patch is in applied https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh

Quoted 7 lines

Can you test the "next" branch and check the difference with your initial patch ( applied in dh branch
https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh
=> https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/0ab3ce72f82b946ac0924dfcdc082792f325eb68 )

I hope that I don't remove something really present on the SOM.

If you are OK, can you send a V2 version with the "next" branch content and I will integrate it in master branch for next pull request.

Will do. I will rebase on master once your PR is in and then send V2.

[...]

#21 lore raw

PATCH 1/5 ARM: stm32: Permit multiple board targets

In reply to Marek Vasut

Hi Marek,

Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Setting TARGET_STM32MP1 in Kconfig always forces SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME to values set by the ST reference platforms. Allow changing that by pulling out the TARGET_STM32MP157C_DK2 and making the ST reference platform settings conditional on TARGET_STM32MP157C_DK2 .
Other platforms can now define a different TARGET_ and thus override the SYS_ settings in their Kconfig.

It seens my configuration between SOC (STM32MP15x) and BOARD is not clean...

So I prepare a patchset to change it.
But I will apply it after your serie...
to avoid regression on your board

Regards Patrick

Quoted 4 lines
Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

---

#22 lore raw

PATCH 1/5 ARM: stm32: Permit multiple board targets

Quoted 15 lines · Patrick DELAUNAY

Hi Marek,

Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Setting TARGET_STM32MP1 in Kconfig always forces SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME to values set by the ST reference platforms. Allow changing that by pulling out the TARGET_STM32MP157C_DK2 and making the ST reference platform settings conditional on TARGET_STM32MP157C_DK2 .
Other platforms can now define a different TARGET_ and thus override the SYS_ settings in their Kconfig.

Quoted 7 lines

It seens my configuration between SOC (STM32MP15x) and BOARD is not clean...

So I prepare a patchset to change it.
But I will apply it after your serie...
to avoid regression on your board

Regards Patrick

Can you apply whatever you feel applicable from the series I posted and push it to some git repo, so I don't have to reset all things over and over again ?

#23 lore raw

PATCH 1/5 ARM: stm32: Permit multiple board targets

Hi Marek,

Quoted 23 lines

From: Marek Vasut <[email protected]>
Sent: lundi 13 janvier 2020 12:08

Quoted 14 lines · Patrick DELAUNAY

Hi Marek,

Quoted 11 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Setting TARGET_STM32MP1 in Kconfig always forces SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME to values set by the ST reference platforms. Allow changing that by pulling out the TARGET_STM32MP157C_DK2 and making the ST reference platform settings conditional on
TARGET_STM32MP157C_DK2 .
Other platforms can now define a different TARGET_ and thus override the SYS_ settings in their Kconfig.

Quoted 3 lines

It seens my configuration between SOC (STM32MP15x) and BOARD is not

clean...

Quoted 1 line
Quoted 8 lines
Quoted 5 lines

So I prepare a patchset to change it.
But I will apply it after your serie...
to avoid regression on your board

Regards Patrick

Can you apply whatever you feel applicable from the series I posted and push it to some git repo, so I don't have to reset all things over and over again ?

Sure.

https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git

=> branch master : the paches accepted
[V3] stm32mp1: configs: Make all boot devices in distro boot conditional

[2/5] ARM: stm32: Allow overriding setup_mac_address()

They will be included in my next pull request

=> branch next
+ my serie = http://patchwork.ozlabs.org/project/uboot/list/?series=152828
+ your serie (including my proposals of update)
http://patchwork.ozlabs.org/project/uboot/list/?series=152293

[3/5] ARM: stm32: Fill in missing loadaddr
=> I change address to 0xc2000000

[5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board
I make a lot of modification after my serie and my review....

Can you check the delta and tell me if it is working...

NB: no more needed after my serie => [1/5] ARM: stm32: Permit multiple board targets i

PS: [4/5] ARM: dts: stm32: Add missing ETHCK clock to ethernet node
I ma waiting Christophe / kernel feedback....

Patrick

#24 lore raw

PATCH 1/5 ARM: stm32: Permit multiple board targets

Quoted 56 lines · Patrick DELAUNAY

Hi Marek,

Quoted 23 lines

From: Marek Vasut <[email protected]>
Sent: lundi 13 janvier 2020 12:08

Quoted 14 lines · Patrick DELAUNAY

Hi Marek,

Quoted 11 lines

From: Marek Vasut <[email protected]>
Sent: vendredi 10 janvier 2020 01:29

Setting TARGET_STM32MP1 in Kconfig always forces SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME to values set by the ST reference platforms. Allow changing that by pulling out the TARGET_STM32MP157C_DK2 and making the ST reference platform settings conditional on
TARGET_STM32MP157C_DK2 .
Other platforms can now define a different TARGET_ and thus override the SYS_ settings in their Kconfig.

Quoted 3 lines

It seens my configuration between SOC (STM32MP15x) and BOARD is not

clean...

Quoted 1 line
Quoted 8 lines
Quoted 5 lines

So I prepare a patchset to change it.
But I will apply it after your serie...
to avoid regression on your board

Regards Patrick

Can you apply whatever you feel applicable from the series I posted and push it to some git repo, so I don't have to reset all things over and over again ?

Sure.

https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git

=> branch master : the paches accepted
[V3] stm32mp1: configs: Make all boot devices in distro boot conditional

[2/5] ARM: stm32: Allow overriding setup_mac_address()

They will be included in my next pull request

=> branch next
+ my serie = http://patchwork.ozlabs.org/project/uboot/list/?series=152828
+ your serie (including my proposals of update)
http://patchwork.ozlabs.org/project/uboot/list/?series=152293

[3/5] ARM: stm32: Fill in missing loadaddr
=> I change address to 0xc2000000

[5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board
I make a lot of modification after my serie and my review....

Quoted 8 lines

Can you check the delta and tell me if it is working...

NB: no more needed after my serie => [1/5] ARM: stm32: Permit multiple board targets i

PS: [4/5] ARM: dts: stm32: Add missing ETHCK clock to ethernet node
I ma waiting Christophe / kernel feedback....

Should be OK, thanks.