Skip to contentSkip to conversation

imx8mq: Generate a single bootable flash.bin again

PATCH In review Patrick Wildt 2 participants 2 messages Jan 8, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 imx8mq: Generate a single bootable flash.bin again

All i.MX8MQ boards have been converted to binman, which makes it necessary to flash both flash.bin and u-boot.itb to get a bootable system. Prior to the conversion, only flash.bin was needed.

Such new requirement breaks existing distro mechanisms to generate the final binary because the extra u-boot.itb is now required.

Generate a final flash.bin that can be used again as a single bootable binary to keep the original behavior.

After this change the SPL binary is called spl.bin, which is a more descriptive name for its purpose, and can still be used standalone (for example, for secure boot purposes).

Also update imx8mq_evk.rst to remove the u-boot.itb copy step.

This is a cherry-pick of 028abfd9b157 ("imx8mm-evk: Generate a single bootable flash.bin again") adjusted to apply to i.MX8MQ.

---
 arch/arm/dts/imx8mq-u-boot.dtsi      | 19 ++++++++++++++++++-
 arch/arm/mach-imx/imx8m/imximage.cfg |  2 +-
 doc/board/nxp/imx8mq_evk.rst         |  1 -
 3 files changed, 19 insertions(+), 3 deletions(-)
arch/arm/dts/imx8mq-u-boot.dtsi +18 -1
index 2c10e9b645..8a6075c77b 100644
@@ -50,7 +50,9 @@
 		};
 	};
 
-	flash {
+	spl {
+		filename = "spl.bin";
+
 		mkimage {
 			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000";
 
@@ -119,4 +121,19 @@
 			};
 		};
 	};
+
+	imx-boot {
+		filename = "flash.bin";
+		pad-byte = <0x00>;
+
+		spl: blob-ext@1 {
+			offset = <0x0>;
+			filename = "spl.bin";
+		};
+
+		uboot: blob-ext@2 {
+			offset = <0x57c00>;
+			filename = "u-boot.itb";
+		};
+	};
 };
arch/arm/mach-imx/imx8m/imximage.cfg +1 -1
index 9c6eaf0a6d..2a3f959183 100644
@@ -8,4 +8,4 @@
 FIT
 BOOT_FROM	sd
 SIGNED_HDMI	signed_hdmi.bin
-LOADER		mkimage.flash.mkimage	0x7e1000
+LOADER		u-boot-spl-ddr.bin	0x7e1000
doc/board/nxp/imx8mq_evk.rst +0 -1
index 92eeda79aa..aa1ecfb47a 100644
@@ -50,7 +50,6 @@ Burn the flash.bin to MicroSD card offset 33KB:
 .. code-block:: bash
 
    $sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33 conv=notrunc
-   $sudo dd if=u-boot.itb of=/dev/sd[x] bs=1024 seek=384 conv=notrunc
 
 Boot
 ----
Signature · 1 line
2.34.1
Reviewed-by on v2 1/1
#1 lore raw
Quoted 14 lines · Patrick Wildt

All i.MX8MQ boards have been converted to binman, which makes it necessary to flash both flash.bin and u-boot.itb to get a bootable system. Prior to the conversion, only flash.bin was needed.

Such new requirement breaks existing distro mechanisms to generate the final binary because the extra u-boot.itb is now required.

Generate a final flash.bin that can be used again as a single bootable binary to keep the original behavior.

After this change the SPL binary is called spl.bin, which is a more descriptive name for its purpose, and can still be used standalone (for example, for secure boot purposes).

Quoted 6 lines

Also update imx8mq_evk.rst to remove the u-boot.itb copy step.

This is a cherry-pick of 028abfd9b157 ("imx8mm-evk: Generate a single bootable flash.bin again") adjusted to apply to i.MX8MQ.

Thanks for the updated commit log:

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-60 Fax: (+49)-8142-66989-80 Email: [email protected]