implement I2C retries for mXT1368
Subsystems (6)
v2 cover implement I2C retries for mXT1368
According to datasheet, mXT1386 chip has a WAKE line, it is used to wake the chip up from deep sleep mode before communicating with it via the I2C-compatible interface.
if the WAKE line is connected to a GPIO line, the line must be asserted 25 ms before the host attempts to communicate with the mXT1386.
If the WAKE line is connected to the SCL pin, the mXT1386 will send a NACK on the first attempt to address it, the host must then retry 25 ms later.
This patch adds compatible string "atmel,mXT1386" for mXT1386 controller, when I2C transfer on mXT1386 fails, retry the transfer once after a 25 ms sleep.
Jiada Wang (3):
dt-bindings: input: atmel: add compatible for mXT1386
Input: atmel_mxt_ts - implement I2C retries for mXT1368
ARM: tegra: add mXT1386 compatible
---
v2:
add bool retry_i2c_transfers to struct mxt_data, to indicate whether retry is needed when i2c transfer fails
v1: initial version
--- .../bindings/input/atmel,maxtouch.txt | 1 + .../boot/dts/tegra20-acer-a500-picasso.dts | 2 +- drivers/input/touchscreen/atmel_mxt_ts.c | 62 +++++++++++++++---- 3 files changed, 52 insertions(+), 13 deletions(-)
Signature · 1 line
2.17.1
PATCH v2 1/3 dt-bindings: input: atmel: add compatible for mXT1386
Document the mXT1386 compatible string.
--- Documentation/devicetree/bindings/input/atmel,maxtouch.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/input/atmel,maxtouch.txt +1 -0
@@ -3,6 +3,7 @@ Atmel maXTouch touchscreen/touchpad Required properties: - compatible: atmel,maxtouch + atmel,mXT1386 The following compatibles have been used in various products but are deprecated:
Signature · 1 line
2.17.1
Re: [PATCH v2 1/3] dt-bindings: input: atmel: add compatible for mXT1386
25.09.2020 16:52, Jiada Wang пишет:
Quoted 13 lines
Document the mXT1386 compatible string.
Signed-off-by Jiada Wang <[email protected]>--- Documentation/devicetree/bindings/input/atmel,maxtouch.txt | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/input/atmel,maxtouch.txt +0
-0
Documentation/devicetree/bindings/input/atmel,maxtouch.txt Atmel maXTouch touchscreen/touchpad · line 9
Quoted 7 lines
Documentation/devicetree/bindings/input/atmel,maxtouch.txt +1
-0@@ -3,6 +3,7 @@ Atmel maXTouch touchscreen/touchpad Required properties: - compatible: atmel,maxtouch + atmel,mXT1386 The following compatibles have been used in various products but are deprecated:
Re: [PATCH v2 1/3] dt-bindings: input: atmel: add compatible for mXT1386
In reply to Jiada WangQuoted 12 lines · Jiada Wang
Document the mXT1386 compatible string.
Signed-off-by Jiada Wang <[email protected]>--- Documentation/devicetree/bindings/input/atmel,maxtouch.txt | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/input/atmel,maxtouch.txt +0
-0
Documentation/devicetree/bindings/input/atmel,maxtouch.txt Atmel maXTouch touchscreen/touchpad · line 6
Quoted 4 lines
Documentation/devicetree/bindings/input/atmel,maxtouch.txt +1
-0@@ -3,6 +3,7 @@ Atmel maXTouch touchscreen/touchpad Required properties: - compatible: atmel,maxtouch + atmel,mXT1386
Compatible strings are preferred to be all lowercase.
Thierry
Re: [PATCH v2 1/3] dt-bindings: input: atmel: add compatible for mXT1386
Hi Thierry
Thanks for your comment
Quoted 8 lines · Thierry Reding
Quoted 7 lines · Jiada Wang
Document the mXT1386 compatible string.
Signed-off-by Jiada Wang <[email protected]>--- Documentation/devicetree/bindings/input/atmel,maxtouch.txt | 1 + 1 file changed, 1 insertion(+)
Quoted 11 lines
Documentation/devicetree/bindings/input/atmel,maxtouch.txt Atmel maXTouch touchscreen/touchpad · line 6
Quoted 9 lines
Documentation/devicetree/bindings/input/atmel,maxtouch.txt +1
-0@@ -3,6 +3,7 @@ Atmel maXTouch touchscreen/touchpad Required properties: - compatible: atmel,maxtouch + atmel,mXT1386Compatible strings are preferred to be all lowercase.
I will update to use lowercase
Thanks,
Jiada
Quoted 3 lines
Thierry
PATCH v2 2/3 Input: atmel_mxt_ts - implement I2C retries for mXT1368
In reply to Jiada WangAccording to datasheet, mXT1386 chip has a WAKE line, it is used to wake the chip up from deep sleep mode before communicating with it via the I2C-compatible interface.
if the WAKE line is connected to a GPIO line, the line must be asserted 25 ms before the host attempts to communicate with the mXT1386. If the WAKE line is connected to the SCL pin, the mXT1386 will send a NACK on the first attempt to address it, the host must then retry 25 ms later.
This patch adds compatible string "atmel,mXT1386" for mXT1386 controller, when I2C transfer on mXT1386 fails, retry the transfer once after a 25 ms sleep.
--- drivers/input/touchscreen/atmel_mxt_ts.c | 62 +++++++++++++++++++----- 1 file changed, 50 insertions(+), 12 deletions(-)
drivers/input/touchscreen/atmel_mxt_ts.c +50 -12
@@ -198,6 +198,7 @@ enum t100_type {#define MXT_CRC_TIMEOUT 1000/* msec */ #define MXT_FW_RESET_TIME 3000/* msec */ #define MXT_FW_CHG_TIMEOUT 300/* msec */ +#define MXT_WAKEUP_TIME 25/* msec */ /* Command to unlock bootloader */ #define MXT_UNLOCK_CMD_MSB 0xaa
@@ -340,6 +341,9 @@ struct mxt_data {unsigned int t19_num_keys;enum mxt_suspend_mode suspend_mode; + +/* Indicates whether retry is needed when i2c transfer fails */ +bool retry_i2c_transfers; };struct mxt_vb2_buffer {
@@ -627,7 +631,9 @@ static int mxt_send_bootloader_cmd(struct mxt_data *data, bool unlock)static int __mxt_read_reg (struct i2c_client *client,u16 reg,u16 len,void *val) { +struct mxt_data *data =i2c_get_clientdata (client);struct i2c_msg xfer[2 ]; +bool retried = false;u8 buf[2 ];int ret;
@@ -646,22 +652,30 @@ static int __mxt_read_reg(struct i2c_client *client, xfer[1 ].len = len; xfer[1 ].buf = val; - ret =i2c_transfer (client->adapter, xfer,2 ); -if (ret ==2 ) { - ret =0 ; - }else { -if (ret >=0 ) - ret = -EIO ; +retry_read: + ret =i2c_transfer (client->adapter, xfer,ARRAY_SIZE (xfer)); +if (ret !=ARRAY_SIZE (xfer)) { +if (data->retry_i2c_transfers && !retried) { +dev_dbg (&client->dev,"i2c retry\n" ); +/* TODO: add WAKE-GPIO support */ +msleep (MXT_WAKEUP_TIME ); + retried = true; + goto retry_read; + } + ret = ret <0 ? ret : -EIO ;dev_err (&client->dev,"%s: i2c transfer failed (%d)\n" , __func__, ret); +return ret; } -return ret; +return 0 ; }static int __mxt_write_reg (struct i2c_client *client,u16 reg,u16 len,const void *val) { +struct mxt_data *data =i2c_get_clientdata (client); +bool retried = false;u8 *buf;size_t count;int ret;
@@ -675,14 +689,21 @@ static int __mxt_write_reg(struct i2c_client *client, u16 reg, u16 len, buf[1 ] = (reg >>8 ) &0xff ;memcpy (&buf[2 ], val, len); +retry_write: ret =i2c_master_send (client, buf, count); -if (ret == count) { - ret =0 ; - }else { -if (ret >=0 ) - ret = -EIO ; +if (ret != count) { +if (data->retry_i2c_transfers && !retried) { +dev_dbg (&client->dev,"i2c retry\n" ); +/* TODO: add WAKE-GPIO support */ +msleep (MXT_WAKEUP_TIME ); + retried = true; + goto retry_write; + } + ret = ret <0 ? ret : -EIO ;dev_err (&client->dev,"%s: i2c send failed (%d)\n" , __func__, ret); + }else { + ret =0 ; }kfree (buf);
@@ -3084,6 +3105,7 @@ static const struct dmi_system_id chromebook_T9_suspend_dmi[] = {static int mxt_probe (struct i2c_client *client,const struct i2c_device_id *id) { +struct device_node *np = client->dev.of_node;struct mxt_data *data;int error;
@@ -3158,6 +3180,20 @@ static int mxt_probe(struct i2c_client *client, const struct i2c_device_id *id)msleep (MXT_RESET_INVALID_CHG ); } +/* +* The mXT1386 has a dedicated WAKE-line that could be connected to a +* dedicated GPIO, or to the I2C SCL pin, or permanently asserted LOW. +* It's used for waking controller from a deep-sleep and it needs to be +* asserted LOW for 25 milliseconds before issuing I2C transfer if controller +* was in a deep-sleep mode. If WAKE-line is connected to I2C SCL pin, then +* the first I2C transfer will get an instant NAK and transfer needs to be +* retried after 25ms. There are too many places in the code where the wake-up +* needs to be inserted, hence it's much easier to add a retry to the common +* I2C accessors, also given that the WAKE-GPIO is unsupported by the driver. +*/ +if (of_device_is_compatible (np,"atmel,mXT1386" )) + data->retry_i2c_transfers = true; + error =mxt_initialize (data);if (error)return error;
@@ -3235,6 +3271,7 @@ static SIMPLE_DEV_PM_OPS(mxt_pm_ops, mxt_suspend, mxt_resume);static const struct of_device_id mxt_of_match[] = { { .compatible ="atmel,maxtouch" , }, + { .compatible ="atmel,mXT1386" , },/* Compatibles listed below are deprecated */ { .compatible ="atmel,qt602240_ts" , }, { .compatible ="atmel,atmel_mxt_ts" , },
@@ -3259,6 +3296,7 @@ static const struct i2c_device_id mxt_id[] = { { "atmel_mxt_tp", 0 }, { "maxtouch", 0 }, { "mXT224", 0 }, + { "mXT1386", 0 }, { } };MODULE_DEVICE_TABLE (i2c, mxt_id);
Signature · 1 line
2.17.1
Re: [PATCH v2 2/3] Input: atmel_mxt_ts - implement I2C retries for mXT1368
25.09.2020 16:52, Jiada Wang пишет:
Quoted 10 lines
According to datasheet, mXT1386 chip has a WAKE line, it is used to wake the chip up from deep sleep mode before communicating with it via the I2C-compatible interface.
if the WAKE line is connected to a GPIO line, the line must be asserted 25 ms before the host attempts to communicate with the mXT1386. If the WAKE line is connected to the SCL pin, the mXT1386 will send a NACK on the first attempt to address it, the host must then retry 25 ms later.
Quoted 8 lines
This patch adds compatible string "atmel,mXT1386" for mXT1386 controller, when I2C transfer on mXT1386 fails, retry the transfer once after a 25 ms sleep.
Signed-off-by Jiada Wang <[email protected]>--- drivers/input/touchscreen/atmel_mxt_ts.c | 62 +++++++++++++++++++----- 1 file changed, 50 insertions(+), 12 deletions(-)
Hello, Jiada! Thank you very much!
Will be nice if this patch could land to v5.10 :)
PATCH v2 3/3 ARM: tegra: add mXT1386 compatible
In reply to Jiada WangAdd mXT1386 compatible for "touchscreen@4c".
--- arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +1 -1
@@ -428,7 +428,7 @@ }; touchscreen@4c { - compatible = "atmel,maxtouch"; + compatible = "atmel,mXT1386", "atmel,maxtouch"; reg = <0x4c>; atmel,cfg_name = "maxtouch-acer-iconia-tab-a500.cfg";
Signature · 1 line
2.17.1
Re: [PATCH v2 3/3] ARM: tegra: add mXT1386 compatible
25.09.2020 16:52, Jiada Wang пишет:
Quoted 13 lines
Add mXT1386 compatible for "touchscreen@4c".
Signed-off-by Jiada Wang <[email protected]>--- arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +0
-0
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts line 434
Quoted 8 lines
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +1
-1@@ -428,7 +428,7 @@ }; touchscreen@4c { - compatible = "atmel,maxtouch"; + compatible = "atmel,mXT1386", "atmel,maxtouch"; reg = <0x4c>; atmel,cfg_name = "maxtouch-acer-iconia-tab-a500.cfg";