PCI: make pci_dev_is_disconnected() helper public for other drivers
Subsystems (3)
RFC PATCH v10 3/5 PCI: make pci_dev_is_disconnected() helper public for other drivers
Make pci_dev_is_disconnected() public so that it can be called from Intel VT-d driver to quickly fix/workaround the surprise removal unplug hang issue for those ATS capable devices on PCIe switch downstream hotplug capable ports.
Beside pci_device_is_present() function, this one has no config space space access, so is light enough to optimize the normal pure surprise removal and safe removal flow.
--- drivers/pci/pci.h | 5 ----- include/linux/pci.h | 5 +++++ 2 files changed, 5 insertions(+), 5 deletions(-)
drivers/pci/pci.h +0 -5
@@ -366,11 +366,6 @@ static inline int pci_dev_set_disconnected(struct pci_dev *dev, void *unused)return 0 ; } -static inline bool pci_dev_is_disconnected (const struct pci_dev *dev) -{ -return dev->error_state == pci_channel_io_perm_failure; -} -/* pci_dev priv_flags */ #define PCI_DEV_ADDED 0#define PCI_DPC_RECOVERED 1
include/linux/pci.h +5 -0
@@ -2506,6 +2506,11 @@ static inline struct pci_dev *pcie_find_root_port(struct pci_dev *dev)return NULL ; } +static inline bool pci_dev_is_disconnected (const struct pci_dev *dev) +{ +return dev->error_state == pci_channel_io_perm_failure; +} +void pci_request_acs (void );bool pci_acs_enabled (struct pci_dev *pdev,u16 acs_flags); bool pci_acs_path_enabled(struct pci_dev *start,
Signature · 1 line
2.31.1
RFC PATCH v10 4/5 iommu/vt-d: don't issue ATS Invalidation request when device is disconnected
Except those aggressive hotplug cases - surprise remove a hotplug device while its safe removal is requested and handled in process by:
1. pull it out directly.
2. turn off its power.
3. bring the link down.
4. just died there that moment.
etc, in a word, 'gone' or 'disconnected'.
Mostly are regular normal safe removal and surprise removal unplug. these hot unplug handling process could be optimized for fix the ATS Invalidation hang issue by calling pci_dev_is_disconnected() in function devtlb_invalidation_with_pasid() to check target device state to avoid sending meaningless ATS Invalidation request to iommu when device is gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)
For safe removal, device wouldn't be removed untill the whole software handling process is done, it wouldn't trigger the hard lock up issue caused by too long ATS Invalidation timeout wait. In safe removal path, device state isn't set to pci_channel_io_perm_failure in pciehp_unconfigure_device() by checking 'presence' parameter, calling pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will return false there, wouldn't break the function.
For surprise removal, device state is set to pci_channel_io_perm_failure in pciehp_unconfigure_device(), means device is already gone (disconnected) call pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will return true to break the function not to send ATS Invalidation request to the disconnected device blindly, thus avoid the further long time waiting triggers the hard lockup.
safe removal & surprise removal
pciehp_ist()
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device(presence)
--- drivers/iommu/intel/pasid.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/iommu/intel/pasid.c +2 -0
@@ -480,6 +480,8 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu,if (!info || !info->ats_enabled)return ; +if (pci_dev_is_disconnected (to_pci_dev (dev))) +return ;/* * When PASID 0 is used, it indicates RID2PASID(DMA request w/o PASID), * devTLB flush w/o PASID should be used. For non-zero PASID under
Signature · 1 line
2.31.1
Baolu Lu
maintainerRe: [RFC PATCH v10 4/5] iommu/vt-d: don't issue ATS Invalidation request when device is disconnected
Quoted 51 lines · Ethan Zhao
Except those aggressive hotplug cases - surprise remove a hotplug device while its safe removal is requested and handled in process by:
1. pull it out directly.
2. turn off its power.
3. bring the link down.
4. just died there that moment.etc, in a word, 'gone' or 'disconnected'.
Mostly are regular normal safe removal and surprise removal unplug. these hot unplug handling process could be optimized for fix the ATS Invalidation hang issue by calling
pci_dev_is_disconnected()in functiondevtlb_invalidation_with_pasid()to check target device state to avoid sending meaningless ATS Invalidation request to iommu when device is gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)For safe removal, device wouldn't be removed untill the whole software handling process is done, it wouldn't trigger the hard lock up issue caused by too long ATS Invalidation timeout wait. In safe removal path, device state isn't set to
pci_channel_io_perm_failureinpciehp_unconfigure_device()by checking 'presence' parameter, callingpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return false there, wouldn't break the function.For surprise removal, device state is set to
pci_channel_io_perm_failureinpciehp_unconfigure_device(), means device is already gone (disconnected) callpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return true to break the function not to send ATS Invalidation request to the disconnected device blindly, thus avoid the further long time waiting triggers the hard lockup.safe removal & surprise removal
pciehp_ist()
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device(presence)Tested-by Haorong Ye <[email protected]>Signed-off-by Ethan Zhao <[email protected]>--- drivers/iommu/intel/pasid.c | 2 ++ 1 file changed, 2 insertions(+)drivers/iommu/intel/pasid.c +0
-0
drivers/iommu/intel/pasid.c devtlb_invalidation_with_pasid(struct intel_iommu *iommu, · line 484
Quoted 5 lines
drivers/iommu/intel/pasid.c +2
-0@@ -480,6 +480,8 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu,if (!info || !info->ats_enabled)return ; +if (pci_dev_is_disconnected (to_pci_dev (dev))) +return ;
Why do you need the above after changes in PATCH 2/5? It's unnecessary and not complete. We have other places where device TLB invalidation is issued, right?
drivers/iommu/intel/pasid.c devtlb_invalidation_with_pasid(struct intel_iommu *iommu, · line 487
Quoted 3 lines
drivers/iommu/intel/pasid.c +0
-0/* * When PASID 0 is used, it indicates RID2PASID(DMA request w/o PASID), * devTLB flush w/o PASID should be used. For non-zero PASID under
Best regards,
baolu
Re: [RFC PATCH v10 4/5] iommu/vt-d: don't issue ATS Invalidation request when device is disconnected
Quoted 47 lines · Baolu Lu
Quoted 46 lines · Ethan Zhao
Except those aggressive hotplug cases - surprise remove a hotplug device while its safe removal is requested and handled in process by:
1. pull it out directly.
2. turn off its power.
3. bring the link down.
4. just died there that moment.etc, in a word, 'gone' or 'disconnected'.
Mostly are regular normal safe removal and surprise removal unplug. these hot unplug handling process could be optimized for fix the ATS Invalidation hang issue by calling
pci_dev_is_disconnected()in functiondevtlb_invalidation_with_pasid()to check target device state to avoid sending meaningless ATS Invalidation request to iommu when device is gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)For safe removal, device wouldn't be removed untill the whole software handling process is done, it wouldn't trigger the hard lock up issue caused by too long ATS Invalidation timeout wait. In safe removal path, device state isn't set to
pci_channel_io_perm_failureinpciehp_unconfigure_device()by checking 'presence' parameter, callingpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return false there, wouldn't break the function.For surprise removal, device state is set to
pci_channel_io_perm_failureinpciehp_unconfigure_device(), means device is already gone (disconnected) callpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return true to break the function not to send ATS Invalidation request to the disconnected device blindly, thus avoid the further long time waiting triggers the hard lockup.safe removal & surprise removal
pciehp_ist()
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device(presence)Tested-by Haorong Ye <[email protected]>Signed-off-by Ethan Zhao <[email protected]>---
drivers/iommu/intel/pasid.c| 2 ++1 file changed, 2 insertions(+)
Quoted 14 lines
drivers/iommu/intel/pasid.c devtlb_invalidation_with_pasid(struct intel_iommu · line 484
Quoted 10 lines
drivers/iommu/intel/pasid.c +1
-0@@ -480,6 +480,8 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, if (!info || !info->ats_enabled) return; + if (pci_dev_is_disconnected(to_pci_dev(dev))) + return;Why do you need the above after changes in PATCH 2/5? It's unnecessary and not complete. We have other places where device TLB invalidation is issued, right?
This one could be regarded as optimization, no need to trapped into rabbit
hole if we could predict the result. because the bad thing is we don't know
what response to us in the rabbit hole from third party switch (bridges will
feedback timeout to requester as PCIe spec mentioned if the endpoint is
gone).
Thanks,
Ethan
Quoted 7 lines
Quoted 4 lines
drivers/iommu/intel/pasid.c +0
-0/** When PASID 0 is used, it indicates RID2PASID(DMA request w/o PASID), * devTLB flush w/o PASID should be used. For non-zero PASID under
Best regards,
baolu
Baolu Lu
maintainerRe: [RFC PATCH v10 4/5] iommu/vt-d: don't issue ATS Invalidation request when device is disconnected
Quoted 66 lines · Ethan Zhao
Quoted 47 lines · Baolu Lu
Quoted 46 lines · Ethan Zhao
Except those aggressive hotplug cases - surprise remove a hotplug device while its safe removal is requested and handled in process by:
1. pull it out directly.
2. turn off its power.
3. bring the link down.
4. just died there that moment.etc, in a word, 'gone' or 'disconnected'.
Mostly are regular normal safe removal and surprise removal unplug. these hot unplug handling process could be optimized for fix the ATS Invalidation hang issue by calling
pci_dev_is_disconnected()in functiondevtlb_invalidation_with_pasid()to check target device state to avoid sending meaningless ATS Invalidation request to iommu when device is gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)For safe removal, device wouldn't be removed untill the whole software handling process is done, it wouldn't trigger the hard lock up issue caused by too long ATS Invalidation timeout wait. In safe removal path, device state isn't set to
pci_channel_io_perm_failureinpciehp_unconfigure_device()by checking 'presence' parameter, callingpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return false there, wouldn't break the function.For surprise removal, device state is set to
pci_channel_io_perm_failureinpciehp_unconfigure_device(), means device is already gone (disconnected) callpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return true to break the function not to send ATS Invalidation request to the disconnected device blindly, thus avoid the further long time waiting triggers the hard lockup.safe removal & surprise removal
pciehp_ist()
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device(presence)Tested-by Haorong Ye <[email protected]>Signed-off-by Ethan Zhao <[email protected]>---
drivers/iommu/intel/pasid.c| 2 ++1 file changed, 2 insertions(+)Quoted 14 lines
drivers/iommu/intel/pasid.c devtlb_invalidation_with_pasid(struct intel_iommu · line 484
Quoted 10 lines
drivers/iommu/intel/pasid.c +1
-0@@ -480,6 +480,8 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, if (!info || !info->ats_enabled) return; + if (pci_dev_is_disconnected(to_pci_dev(dev))) + return;Why do you need the above after changes in PATCH 2/5? It's unnecessary and not complete. We have other places where device TLB invalidation is issued, right?
This one could be regarded as optimization, no need to trapped into rabbit
Quoted 7 lines
hole if we could predict the result. because the bad thing is we don't know
what response to us in the rabbit hole from third party switch (bridges will
feedback timeout to requester as PCIe spec mentioned if the endpoint is
gone).
The IOMMU hardware has its own timeout mechanism. This timeout might happen if:
1) The link to the endpoint is broken, so the invalidation completion message is lost on the way.
2) The device has a longer timeout value, so the device is still busy with handling the cache invalidation when IOMMU's timeout is triggered.
Here, we are doing the following:
For Case 1, we return -ETIMEDOUT directly. For Case 2, we attempt to retry.
Best regards,
baolu
Re: [RFC PATCH v10 4/5] iommu/vt-d: don't issue ATS Invalidation request when device is disconnected
Quoted 84 lines · Baolu Lu
Quoted 66 lines · Ethan Zhao
Quoted 47 lines · Baolu Lu
Quoted 46 lines · Ethan Zhao
Except those aggressive hotplug cases - surprise remove a hotplug device while its safe removal is requested and handled in process by:
1. pull it out directly.
2. turn off its power.
3. bring the link down.
4. just died there that moment.etc, in a word, 'gone' or 'disconnected'.
Mostly are regular normal safe removal and surprise removal unplug. these hot unplug handling process could be optimized for fix the ATS Invalidation hang issue by calling
pci_dev_is_disconnected()in functiondevtlb_invalidation_with_pasid()to check target device state to avoid sending meaningless ATS Invalidation request to iommu when device is gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)For safe removal, device wouldn't be removed untill the whole software handling process is done, it wouldn't trigger the hard lock up issue caused by too long ATS Invalidation timeout wait. In safe removal path, device state isn't set to
pci_channel_io_perm_failureinpciehp_unconfigure_device()by checking 'presence' parameter, callingpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return false there, wouldn't break the function.For surprise removal, device state is set to
pci_channel_io_perm_failureinpciehp_unconfigure_device(), means device is already gone (disconnected) callpci_dev_is_disconnected()indevtlb_invalidation_with_pasid()will return true to break the function not to send ATS Invalidation request to the disconnected device blindly, thus avoid the further long time waiting triggers the hard lockup.safe removal & surprise removal
pciehp_ist()
pciehp_handle_presence_or_link_change()
pciehp_disable_slot()
remove_board()
pciehp_unconfigure_device(presence)Tested-by Haorong Ye <[email protected]>Signed-off-by Ethan Zhao <[email protected]>---
drivers/iommu/intel/pasid.c| 2 ++1 file changed, 2 insertions(+)Quoted 14 lines
drivers/iommu/intel/pasid.c devtlb_invalidation_with_pasid(struct · line 484
Quoted 10 lines
drivers/iommu/intel/pasid.c +1
-0@@ -480,6 +480,8 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu, if (!info || !info->ats_enabled) return; + if (pci_dev_is_disconnected(to_pci_dev(dev))) + return;Why do you need the above after changes in PATCH 2/5? It's unnecessary and not complete. We have other places where device TLB invalidation is issued, right?
This one could be regarded as optimization, no need to trapped into rabbit
Quoted 7 lines
hole if we could predict the result. because the bad thing is we don't know
what response to us in the rabbit hole from third party switch (bridges will
feedback timeout to requester as PCIe spec mentioned if the endpoint is
gone).
The IOMMU hardware has its own timeout mechanism. This timeout might happen if:
1) The link to the endpoint is broken, so the invalidation completion message is lost on the way.
2) The device has a longer timeout value, so the device is still busy with handling the cache invalidation when IOMMU's timeout is triggered.
Quoted 4 lines
Here, we are doing the following:
For Case 1, we return
-ETIMEDOUTdirectly. For Case 2, we attempt to retry.
Yes, Intel VT-d will setup a hardware timer if devtlb invalidation issued and
wait descripton submitted, that hardware timer is limited resource, will tick
till gets the timeout if the endpoint is dead/broken etc.
even we bail out in qi_submit_sync() for case #1, the hardware timer still
ticks there, if many of such request issued, the iommu will run out of
hardware resouce. so we should avoid such case as possible as we could.
though the Intel VT-d says the timeout value will not more than "
PCIe read timeout", but in fact, we got more than 12 seconds before get
ITE.
for case #2, the retry has pre-conditon as I know, there is fault, cleared.
So I call it "rabbit hole".
To run into that rabbit hole is last choice, not best.
Thanks,
Ethan
Quoted 3 lines
Best regards,
baolu
RFC PATCH v10 5/5 iommu/vt-d: don't loop for timeout ATS Invalidation request forever
In reply to Ethan ZhaoWhen the ATS Invalidation request timeout happens, the qi_submit_sync() will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as the fq_timer to issue invalidation request, cause the system lockup as following
[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002
RAX: 0000000000000101 RBX: ffffffffab36c2a0 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffab36c2a0
RBP: ffffffffab36c2a0 R8: 0000000000000001 R9: 0000000000000000
R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14: ffff9e10d71b1c88 R15: ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
--- drivers/iommu/intel/dmar.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/iommu/intel/dmar.c +1 -1
@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu, struct qi_desc *desc,reclaim_free_desc (qi);raw_spin_unlock_irqrestore (&qi->q_lock, flags); -if (rc == -EAGAIN ) +if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;if (iotlb_start_ktime)
Signature · 1 line
2.31.1
Re: [RFC PATCH v10 5/5] iommu/vt-d: don't loop for timeout ATS Invalidation request forever
Quoted 13 lines · Ethan Zhao
When the ATS Invalidation request timeout happens, the
qi_submit_sync()will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as thefq_timerto issue invalidation request, cause the system lockup as following[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002RAX: 0000000000000101 RBX:
ffffffffab36c2a0RCX: 0000000000000000RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffffffffab36c2a0
Quoted 7 lines
RBP:
ffffffffab36c2a0R8: 0000000000000001 R9: 0000000000000000R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14:
ffff9e10d71b1c88R15:ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#12 [ffffb202f268cdc8] native_queued_spin_lock_slowpath at ffffffffa9d1025c
#13 [ffffb202f268cdc8] do_raw_spin_lock at ffffffffa9d121f1
#14 [ffffb202f268cdd8] _raw_spin_lock_irqsave at ffffffffaa51795b
#15 [ffffb202f268cdf8] iommu_flush_dev_iotlb at ffffffffaa20df48
#16 [ffffb202f268ce28] iommu_flush_iova at ffffffffaa20e182
#17 [ffffb202f268ce60] iova_domain_flush at ffffffffaa220e27
#18 [ffffb202f268ce70] fq_flush_timeout at ffffffffaa221c9d
#19 [ffffb202f268cea8] call_timer_fn at ffffffffa9d46661
#20 [ffffb202f268cf08] run_timer_softirq at ffffffffa9d47933
#21 [ffffb202f268cf98] __softirqentry_text_start at ffffffffaa8000e0
#22 [ffffb202f268cff0] asm_call_sysvec_on_stack at ffffffffaa60114f
This part get lost perhpas I append "----" here.
Thanks,
Ethan
Quoted 25 lines
(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
Signed-off-by Ethan Zhao <[email protected]>--- drivers/iommu/intel/dmar.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/iommu/intel/dmar.c +1
-1@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu, struct qi_desc *desc,reclaim_free_desc (qi);raw_spin_unlock_irqrestore (&qi->q_lock, flags); -if (rc == -EAGAIN ) +if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;if (iotlb_start_ktime)
Baolu Lu
maintainerRe: [RFC PATCH v10 5/5] iommu/vt-d: don't loop for timeout ATS Invalidation request forever
In reply to Ethan ZhaoQuoted 37 lines · Ethan Zhao
When the ATS Invalidation request timeout happens, the
qi_submit_sync()will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as thefq_timerto issue invalidation request, cause the system lockup as following[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002RAX: 0000000000000101 RBX:
ffffffffab36c2a0RCX: 0000000000000000RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffffffffab36c2a0RBP:
ffffffffab36c2a0R8: 0000000000000001 R9: 0000000000000000R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14:
ffff9e10d71b1c88R15:ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
Signed-off-by Ethan Zhao <[email protected]>--- drivers/iommu/intel/dmar.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/iommu/intel/dmar.c +0
-0
drivers/iommu/intel/dmar.c int qi_submit_sync(struct intel_iommu *iommu, struct qi_desc *desc, · line 1459
Quoted 8 lines
drivers/iommu/intel/dmar.c +1
-1@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu, struct qi_desc *desc,reclaim_free_desc (qi);raw_spin_unlock_irqrestore (&qi->q_lock, flags); -if (rc == -EAGAIN ) +if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;if (iotlb_start_ktime)
Above is also unnecessary if qi_check_fault() returns -ETIMEDOUT, instead of -EAGAIN. Or did I miss anything?
Best regards,
baolu
Re: [RFC PATCH v10 5/5] iommu/vt-d: don't loop for timeout ATS Invalidation request forever
Quoted 33 lines · Baolu Lu
Quoted 32 lines · Ethan Zhao
When the ATS Invalidation request timeout happens, the
qi_submit_sync()will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as thefq_timerto issue invalidation request, cause the system lockup as following[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002RAX: 0000000000000101 RBX:
ffffffffab36c2a0RCX: 0000000000000000RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffffffffab36c2a0RBP:
ffffffffab36c2a0R8: 0000000000000001 R9: 0000000000000000R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14:
ffff9e10d71b1c88R15:ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
Signed-off-by Ethan Zhao <[email protected]>---
drivers/iommu/intel/dmar.c| 2 +-1 file changed, 1 insertion(+), 1 deletion(-)
Quoted 16 lines
Quoted 12 lines
drivers/iommu/intel/dmar.c +1
-0@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu,struct qi_desc *desc, reclaim_free_desc(qi); raw_spin_unlock_irqrestore(&qi->q_lock, flags); - if (rc == -EAGAIN) + if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;Quoted 1 line
if (
iotlb_start_ktime)Above is also unnecessary if
qi_check_fault()returns-ETIMEDOUT, instead of-EAGAIN. Or did I miss anything?
It is pro if we fold it into qi_check_fault(), the con is we have to add
more parameter to qi_check_fault(), no need check invalidation type
of QI_DIOTLB_TYPE&QI_DEIOTLB_TYPE in qi_check_fault() ?
Thanks,
Ethan
Quoted 3 lines
Best regards,
baolu
Baolu Lu
maintainerRe: [RFC PATCH v10 5/5] iommu/vt-d: don't loop for timeout ATS Invalidation request forever
Quoted 52 lines · Ethan Zhao
Quoted 33 lines · Baolu Lu
Quoted 32 lines · Ethan Zhao
When the ATS Invalidation request timeout happens, the
qi_submit_sync()will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as thefq_timerto issue invalidation request, cause the system lockup as following[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002RAX: 0000000000000101 RBX:
ffffffffab36c2a0RCX: 0000000000000000RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffffffffab36c2a0RBP:
ffffffffab36c2a0R8: 0000000000000001 R9: 0000000000000000R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14:
ffff9e10d71b1c88R15:ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
Signed-off-by Ethan Zhao <[email protected]>---
drivers/iommu/intel/dmar.c| 2 +-1 file changed, 1 insertion(+), 1 deletion(-)Quoted 16 lines
Quoted 12 lines
drivers/iommu/intel/dmar.c +1
-0@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu,struct qi_desc *desc, reclaim_free_desc(qi); raw_spin_unlock_irqrestore(&qi->q_lock, flags); - if (rc == -EAGAIN) + if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;Quoted 1 line
if (
iotlb_start_ktime)Above is also unnecessary if
qi_check_fault()returns-ETIMEDOUT, instead of-EAGAIN. Or did I miss anything?
Quoted 5 lines
It is pro if we fold it into
qi_check_fault(), the con is we have to addmore parameter to
qi_check_fault(), no need check invalidation typeof QI_DIOTLB_TYPE&QI_DEIOTLB_TYPE in
qi_check_fault()?
No need to check the request type as multiple requests might be batched together in a single call. This is also the reason why I asked you to add a flag bit to this helper and make the intention explicit, say,
"This includes requests to interact with a PCI endpoint. The device may
become unavailable at any time, so do not attempt to retry if ITE is detected and the device has gone away."
Best regards,
baolu
Re: [RFC PATCH v10 5/5] iommu/vt-d: don't loop for timeout ATS Invalidation request forever
Quoted 59 lines · Baolu Lu
Quoted 52 lines · Ethan Zhao
Quoted 33 lines · Baolu Lu
Quoted 32 lines · Ethan Zhao
When the ATS Invalidation request timeout happens, the
qi_submit_sync()will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as thefq_timerto issue invalidation request, cause the system lockup as following[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002RAX: 0000000000000101 RBX:
ffffffffab36c2a0RCX: 0000000000000000RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffffffffab36c2a0RBP:
ffffffffab36c2a0R8: 0000000000000001 R9: 0000000000000000R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14:
ffff9e10d71b1c88R15:ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
Signed-off-by Ethan Zhao <[email protected]>---
drivers/iommu/intel/dmar.c| 2 +-1 file changed, 1 insertion(+), 1 deletion(-)Quoted 16 lines
Quoted 12 lines
drivers/iommu/intel/dmar.c +1
-0@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu,struct qi_desc *desc, reclaim_free_desc(qi); raw_spin_unlock_irqrestore(&qi->q_lock, flags); - if (rc == -EAGAIN) + if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;Quoted 1 line
if (
iotlb_start_ktime)Above is also unnecessary if
qi_check_fault()returns-ETIMEDOUT, instead of-EAGAIN. Or did I miss anything?Quoted 5 lines
It is pro if we fold it into
qi_check_fault(), the con is we have to addmore parameter to
qi_check_fault(), no need check invalidation typeof QI_DIOTLB_TYPE&QI_DEIOTLB_TYPE in
qi_check_fault()?
Quoted 7 lines
No need to check the request type as multiple requests might be batched together in a single call. This is also the reason why I asked you to add a flag bit to this helper and make the intention explicit, say,
"This includes requests to interact with a PCI endpoint. The device may become unavailable at any time, so do not attempt to retry if ITE is detected and the device has gone away."
That is to say, the usage of this function finally becomes that way,
the user space interface could submit request with mixed iotlb & devtlb
invalidation together in the queue or seperated iotlb/devtlb invalidation.
we depend on caller to pass the QI_OPT_CHECK_ENDPOINT as option
bit to bail out even there is other iotlb invalidation in the same batch ?
then is user's call to choose retry the iotbl /devtlb invalidation or not.
if the caller hits the case the endpoint dead, the caller will get -ETIMEDOUT/
-ENOTCONN as returned value, but no real ITE in its interested list, to
tell userland user what happened, we fake a DMA_FSTS_ITE for user ?
given we wouldn't read a ITE from DMA_FSTS_REG that moment.
1. checking the first request for devTLB invalidation will miss chance to
check endpoint state if the iotlb & devtlb invalidation were mixed.
here explict option bit would be better. while valid pdev does the
same thing. so if pdev passed, no need to check for QI_DIOTLB_TYPE
|| QI_EIOTLB_TYPE in qi_submit_sync() & qi_check_fault().
2. seems not perfect to drop or retry whole batch of request if there is
devtlb invalidation within the batch, let caller to choose the later action
is simpler than making the qi_submit_sync() too complex.
3. fake a DMA_FSTS_ITE for user's interested list on behalf of hardware
is better than no error/ fault feedback to user even it is predicted not
happened yet.
my cents.
Thanks,
Ethan
Quoted 3 lines
Best regards,
baolu
Re: [RFC PATCH v10 5/5] iommu/vt-d: don't loop for timeout ATS Invalidation request forever
Quoted 106 lines · Ethan Zhao
Quoted 59 lines · Baolu Lu
Quoted 52 lines · Ethan Zhao
Quoted 33 lines · Baolu Lu
Quoted 32 lines · Ethan Zhao
When the ATS Invalidation request timeout happens, the
qi_submit_sync()will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as thefq_timerto issue invalidation request, cause the system lockup as following[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002RAX: 0000000000000101 RBX:
ffffffffab36c2a0RCX: 0000000000000000RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffffffffab36c2a0RBP:
ffffffffab36c2a0R8: 0000000000000001 R9: 0000000000000000R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14:
ffff9e10d71b1c88R15:ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
Signed-off-by Ethan Zhao <[email protected]>---
drivers/iommu/intel/dmar.c| 2 +-1 file changed, 1 insertion(+), 1 deletion(-)Quoted 16 lines
Quoted 12 lines
drivers/iommu/intel/dmar.c +1
-0@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu, struct qi_desc *desc, reclaim_free_desc(qi); raw_spin_unlock_irqrestore(&qi->q_lock, flags); - if (rc == -EAGAIN) + if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;Quoted 1 line
if (
iotlb_start_ktime)Above is also unnecessary if
qi_check_fault()returns-ETIMEDOUT, instead of-EAGAIN. Or did I miss anything?Quoted 5 lines
It is pro if we fold it into
qi_check_fault(), the con is we have to addmore parameter to
qi_check_fault(), no need check invalidation typeof QI_DIOTLB_TYPE&QI_DEIOTLB_TYPE in
qi_check_fault()?Quoted 7 lines
No need to check the request type as multiple requests might be batched together in a single call. This is also the reason why I asked you to add a flag bit to this helper and make the intention explicit, say,
"This includes requests to interact with a PCI endpoint. The device may become unavailable at any time, so do not attempt to retry if ITE is detected and the device has gone away."
That is to say, the usage of this function finally becomes that way,
the user space interface could submit request with mixed iotlb & devtlb
invalidation together in the queue or seperated iotlb/devtlb invalidation.
we depend on caller to pass the
QI_OPT_CHECK_ENDPOINTas optionbit to bail out even there is other iotlb invalidation in the same batch ?
then is user's call to choose retry the iotbl /devtlb invalidation or not.
if the caller hits the case the endpoint dead, the caller will get
(quoted diff) +0
-2-ETIMEDOUT/ -ENOTCONN as returned value, but no real ITE in its interested list, totell userland user what happened, we fake a
DMA_FSTS_ITEfor user ?given we wouldn't read a ITE from
DMA_FSTS_REGthat moment.1. checking the first request for devTLB invalidation will miss chance to
check endpoint state if the iotlb & devtlb invalidation were mixed.
here explict option bit would be better. while valid pdev does the
same thing. so if pdev passed, no need to check for
QI_DIOTLB_TYPE||
QI_EIOTLB_TYPEinqi_submit_sync()&qi_check_fault().2. seems not perfect to drop or retry whole batch of request if there is
devtlb invalidation within the batch, let caller to choose the later action
Quoted 10 lines
is simpler than making the
qi_submit_sync()too complex.3. fake a
DMA_FSTS_ITEfor user's interested list on behalf of hardwareis better than no error/ fault feedback to user even it is predicted not
happened yet.
See Intel VT-d spec r4.1, section 4.3 & section 6.5.2.10
We should keep the original retry logic intact, in order to not break
the fault handling flow. only breaks the loop when endpoint device
is gone with returned error code to reflect the reality. not -ETIMEOUT,
that is not triggered yet, but will hit ITE later about previous request,
and software should handle it smoothly to let the other subsequent
requests could be done in next try.
Thanks,
Ethan
Quoted 13 lines
my cents.
Thanks,
Ethan
Quoted 3 lines
Best regards,
baolu
Re: [RFC PATCH v10 5/5] iommu/vt-d: don't loop for timeout ATS Invalidation request forever
In reply to Ethan ZhaoQuoted 37 lines · Ethan Zhao
When the ATS Invalidation request timeout happens, the
qi_submit_sync()will restart and loop for the invalidation request forever till it is done, it will block another Invalidation thread such as thefq_timerto issue invalidation request, cause the system lockup as following[exception RIP: native_queued_spin_lock_slowpath+92]
RIP: ffffffffa9d1025c RSP: ffffb202f268cdc8 RFLAGS: 00000002RAX: 0000000000000101 RBX:
ffffffffab36c2a0RCX: 0000000000000000RDX: 0000000000000000 RSI: 0000000000000000 RDI:
ffffffffab36c2a0RBP:
ffffffffab36c2a0R8: 0000000000000001 R9: 0000000000000000R10: 0000000000000010 R11: 0000000000000018 R12: 0000000000000000
R13: 0000000000000004 R14:
ffff9e10d71b1c88R15:ffff9e10d71b1980
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018(the left part of exception see the hotplug case of ATS capable device)
If one endpoint device just no response to the ATS Invalidation request, but is not gone, it will bring down the whole system, to avoid such case, don't try the timeout ATS Invalidation request forever.
Signed-off-by Ethan Zhao <[email protected]>--- drivers/iommu/intel/dmar.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/iommu/intel/dmar.c +0
-0
drivers/iommu/intel/dmar.c int qi_submit_sync(struct intel_iommu *iommu, struct qi_desc *desc, · line 1459
Quoted 8 lines
drivers/iommu/intel/dmar.c +1
-1@@ -1453,7 +1453,7 @@ int qi_submit_sync(struct intel_iommu *iommu, struct qi_desc *desc,reclaim_free_desc (qi);raw_spin_unlock_irqrestore (&qi->q_lock, flags); -if (rc == -EAGAIN ) +if (rc == -EAGAIN && type !=QI_DIOTLB_TYPE && type !=QI_DEIOTLB_TYPE ) goto restart;if (iotlb_start_ktime)
mark, only break the loop when the sid of ITE is the same as current target
pdev. need check the target dev is pf or vf.
The ITE is possible left by previous devtlb invalidation request for other device.
Thanks,
Ethan
Baolu Lu
maintainerQuoted 9 lines · Ethan Zhao
Make
pci_dev_is_disconnected()public so that it can be called from Intel VT-d driver to quickly fix/workaround the surprise removal unplug hang issue for those ATS capable devices on PCIe switch downstream hotplug capable ports.Beside
pci_device_is_present()function, this one has no config space space access, so is light enough to optimize the normal pure surprise removal and safe removal flow.
Quoted 6 lines
Tested-by Haorong Ye<[email protected]>Signed-off-by Ethan Zhao<[email protected]>--- drivers/pci/pci.h | 5 ----- include/linux/pci.h | 5 +++++ 2 files changed, 5 insertions(+), 5 deletions(-)
This should be moved before PATCH 2/5? Otherwise, PATCH 2/5 couldn't be compiled.
Best regards,
baolu
Quoted 10 lines · Baolu Lu
Quoted 9 lines · Ethan Zhao
Make
pci_dev_is_disconnected()public so that it can be called from Intel VT-d driver to quickly fix/workaround the surprise removal unplug hang issue for those ATS capable devices on PCIe switch downstream hotplug capable ports.Beside
pci_device_is_present()function, this one has no config space space access, so is light enough to optimize the normal pure surprise removal and safe removal flow.
Quoted 8 lines
Quoted 6 lines
Tested-by Haorong Ye<[email protected]>Signed-off-by Ethan Zhao<[email protected]>---
drivers/pci/pci.h | 5 -----
include/linux/pci.h| 5 +++++2 files changed, 5 insertions(+), 5 deletions(-)This should be moved before PATCH 2/5? Otherwise, PATCH 2/5 couldn't be
Seems the order was mixed when send-email was abort by network connection
and sent again.
[3/5] &[4/5] goes to upset. though the subject order is right.
anyway will resend in next version.
Thanks,
Ethan
Quoted 4 lines
compiled.
Best regards,
baolu