dt-bindings: convert ata/cortina,gemini-sata-bridge to yaml
Subsystems (2)
PATCH v4 1/1 dt-bindings: convert ata/cortina,gemini-sata-bridge to yaml
This patch converts ata/cortina,gemini-sata-bridge binding to yaml
---
Change since v1:
- fixed cosmetic nits reported by Damien Le Moal Changes since v2:
- Added blank lines between properties
- Removed useless quotes and label
- Re-indented description
Change since v3:
- fixed all min/maxitems reported by Krzysztof Kozlowski
.../ata/cortina,gemini-sata-bridge.txt | 55 --------- .../ata/cortina,gemini-sata-bridge.yaml | 109 ++++++++++++++++++ 2 files changed, 109 insertions(+), 55 deletions(-) delete mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt create mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt deleted +0 -55
@@ -1,55 +0,0 @@ -* Cortina Systems Gemini SATA Bridge - -The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that -takes two Faraday Technology FTIDE010 PATA controllers and bridges -them in different configurations to two SATA ports. - -Required properties: -- compatible: should be - "cortina,gemini-sata-bridge" -- reg: registers and size for the block -- resets: phandles to the reset lines for both SATA bridges -- reset-names: must be "sata0", "sata1" -- clocks: phandles to the compulsory peripheral clocks -- clock-names: must be "SATA0_PCLK", "SATA1_PCLK" -- syscon: a phandle to the global Gemini system controller -- cortina,gemini-ata-muxmode: tell the desired multiplexing mode for - the ATA controller and SATA bridges. Values 0..3: - Mode 0: ata0 master <-> sata0 - ata1 master <-> sata1 - ata0 slave interface brought out on IDE pads - Mode 1: ata0 master <-> sata0 - ata1 master <-> sata1 - ata1 slave interface brought out on IDE pads - Mode 2: ata1 master <-> sata1 - ata1 slave <-> sata0 - ata0 master and slave interfaces brought out - on IDE pads - Mode 3: ata0 master <-> sata0 - ata0 slave <-> sata1 - ata1 master and slave interfaces brought out - on IDE pads - -Optional boolean properties: -- cortina,gemini-enable-ide-pins: enables the PATA to IDE connection. - The muxmode setting decides whether ATA0 or ATA1 is brought out, - and whether master, slave or both interfaces get brought out. -- cortina,gemini-enable-sata-bridge: enables the PATA to SATA bridge - inside the Gemnini SoC. The Muxmode decides what PATA blocks will - be muxed out and how. - -Example: - -sata: sata@46000000 { - compatible = "cortina,gemini-sata-bridge"; - reg = <0x46000000 0x100>; - resets = <&rcon 26>, <&rcon 27>; - reset-names = "sata0", "sata1"; - clocks = <&gcc GEMINI_CLK_GATE_SATA0>, - <&gcc GEMINI_CLK_GATE_SATA1>; - clock-names = "SATA0_PCLK", "SATA1_PCLK"; - syscon = <&syscon>; - cortina,gemini-ata-muxmode = <3>; - cortina,gemini-enable-ide-pins; - cortina,gemini-enable-sata-bridge; -};
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +109 -0
109 lines not on this page · raw message
Signature · 1 line
2.34.1
Quoted 123 lines · Corentin Labbe
This patch converts ata/cortina,gemini-sata-bridge binding to yaml
Reviewed-by Linus Walleij <[email protected]>Acked-by Damien Le Moal <[email protected]>Signed-off-by Corentin Labbe <[email protected]>---
Change since v1:
- fixed cosmetic nits reported by Damien Le Moal Changes since v2:
- Added blank lines between properties
- Removed useless quotes and label
- Re-indented description
Change since v3:
- fixed all min/maxitems reported by Krzysztof Kozlowski.../ata/cortina,gemini-sata-bridge.txt | 55 --------- .../ata/cortina,gemini-sata-bridge.yaml | 109 ++++++++++++++++++ 2 files changed, 109 insertions(+), 55 deletions(-) delete mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt create mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yamlDocumentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt deleted +0
-55@@ -1,55 +0,0 @@ -* Cortina Systems Gemini SATA Bridge - -The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that -takes two Faraday Technology FTIDE010 PATA controllers and bridges -them in different configurations to two SATA ports. - -Required properties: -- compatible: should be - "cortina,gemini-sata-bridge" -- reg: registers and size for the block -- resets: phandles to the reset lines for both SATA bridges -- reset-names: must be "sata0", "sata1" -- clocks: phandles to the compulsory peripheral clocks -- clock-names: must be "SATA0_PCLK", "SATA1_PCLK" -- syscon: a phandle to the global Gemini system controller -- cortina,gemini-ata-muxmode: tell the desired multiplexing mode for - the ATA controller and SATA bridges. Values 0..3: - Mode 0: ata0 master <-> sata0 - ata1 master <-> sata1 - ata0 slave interface brought out on IDE pads - Mode 1: ata0 master <-> sata0 - ata1 master <-> sata1 - ata1 slave interface brought out on IDE pads - Mode 2: ata1 master <-> sata1 - ata1 slave <-> sata0 - ata0 master and slave interfaces brought out - on IDE pads - Mode 3: ata0 master <-> sata0 - ata0 slave <-> sata1 - ata1 master and slave interfaces brought out - on IDE pads - -Optional boolean properties: -- cortina,gemini-enable-ide-pins: enables the PATA to IDE connection. - The muxmode setting decides whether ATA0 or ATA1 is brought out, - and whether master, slave or both interfaces get brought out. -- cortina,gemini-enable-sata-bridge: enables the PATA to SATA bridge - inside the Gemnini SoC. The Muxmode decides what PATA blocks will - be muxed out and how. - -Example: - -sata: sata@46000000 { - compatible = "cortina,gemini-sata-bridge"; - reg = <0x46000000 0x100>; - resets = <&rcon 26>, <&rcon 27>; - reset-names = "sata0", "sata1"; - clocks = <&gcc GEMINI_CLK_GATE_SATA0>, - <&gcc GEMINI_CLK_GATE_SATA1>; - clock-names = "SATA0_PCLK", "SATA1_PCLK"; - syscon = <&syscon>; - cortina,gemini-ata-muxmode = <3>; - cortina,gemini-enable-ide-pins; - cortina,gemini-enable-sata-bridge; -};Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +35
-0@@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/cortina,gemini-sata-bridge.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cortina Systems Gemini SATA Bridge + +maintainers: + - Linus Walleij <[email protected]> + +description: | + The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that + takes two Faraday Technology FTIDE010 PATA controllers and bridges + them in different configurations to two SATA ports. + +properties: + compatible: + const: cortina,gemini-sata-bridge + + reg: + maxItems: 1 + + resets: + minItems: 2 + maxItems: 2 + description: phandles to the reset lines for both SATA bridges + + reset-names: + items: + - const: sata0 + - const: sata1 + + clocks: + minItems: 2
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml line 45
Quoted 10 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +10
-0+ maxItems: 2 + description: phandles to the compulsory peripheral clocks + + clock-names: + items: + - const: SATA0_PCLK + - const: SATA1_PCLK + + syscon: + maxItems: 1
My bad, I am sorry for misleading you earlier, this is just a phandle, so should be without any min/maxItems.
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml line 48
Quoted 3 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +3
-0+ $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to the global Gemini system controller +
With maxItems removed:
Best regards,
Krzysztof