ARM: dts: stm32: Drop QSPI CS2 on DHCOM
Subsystems (3)
PATCH 1/1 ARM: dts: stm32: Drop QSPI CS2 on DHCOM
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash at 1.
--- arch/arm/dts/stm32mp15xx-dhcom.dtsi | 13 ++----------- 1 file changed, 2 insertions(+), 11 deletions(-)
arch/arm/dts/stm32mp15xx-dhcom.dtsi +2 -11
@@ -299,8 +299,8 @@ &qspi { pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; #address-cells = <1>; #size-cells = <0>;
@@ -314,15 +314,6 @@ #address-cells = <1>; #size-cells = <1>; }; - - flash1: mx66l51235l at 1 { - compatible = "jedec,spi-nor"; - reg = <1>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; }; &rng1 {
Signature · 1 line
2.28.0
PATCH 1/1 ARM: dts: stm32: Drop QSPI CS2 on DHCOM
Hi Marek
Quoted 30 lines · Marek Vasut
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash at 1.
Signed-off-by Marek Vasut <[email protected]>Cc Patrice Chotard <[email protected]>Cc Patrick Delaunay <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcom.dtsi | 13 ++----------- 1 file changed, 2 insertions(+), 11 deletions(-)arch/arm/dts/stm32mp15xx-dhcom.dtsi +2
-4@@ -299,8 +299,8 @@ &qspi { pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; #address-cells = <1>; #size-cells = <0>;@@ -314,15 +314,6 @@ #address-cells = <1>; #size-cells = <1>; }; - - flash1: mx66l51235l at 1 {
arch/arm/dts/stm32mp15xx-dhcom.dtsi line 319
Quoted 10 lines
arch/arm/dts/stm32mp15xx-dhcom.dtsi +0
-7- compatible = "jedec,spi-nor"; - reg = <1>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; }; &rng1 {
Thanks
Patrice
PATCH 1/1 ARM: dts: stm32: Drop QSPI CS2 on DHCOM
In reply to Marek VasutHi Marek,
Quoted 8 lines
From: Marek Vasut <[email protected]>
Sent: mercredi 28 octobre 2020 21:38
To: u-boot at lists.denx.de
Cc: Marek Vasut <[email protected]>; Patrice CHOTARD <[email protected]>; Patrick DELAUNAY <[email protected]>
Subject: [PATCH] ARM: dts: stm32: Drop QSPI CS2 on DHCOM
Importance: High
Quoted 9 lines
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash at 1.
Signed-off-by Marek Vasut <[email protected]>Cc Patrice Chotard <[email protected]>Cc Patrick Delaunay <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcom.dtsi | 13 ++----------- 1 file changed, 2 insertions(+), 11 deletions(-)
Thanks
Patrick
PATCH 1/1 ARM: dts: stm32: Drop QSPI CS2 on DHCOM
In reply to Marek VasutHi Marek,
Quoted 12 lines
From: Marek Vasut <[email protected]>
Sent: mercredi 28 octobre 2020 21:38The QSPI CS2 is not used on DHCOM, remove the pinmux and flash at 1.
Signed-off-by Marek Vasut <[email protected]>Cc Patrice Chotard <[email protected]>Cc Patrick Delaunay <[email protected]>--- arch/arm/dts/stm32mp15xx-dhcom.dtsi | 13 ++----------- 1 file changed, 2 insertions(+), 11 deletions(-)
Applied to u-boot-stm/master, thanks!
Regards
Patrick