Add basic node support for Mediatek MT8183 SoC
Subsystems (3)
v11 cover Add basic node support for Mediatek MT8183 SoC
MT8183 is a SoC based on 64bit ARMv8 architecture.
It contains 4 CA53 and 4 CA73 cores.
MT8183 share many HW IP with MT65xx series.
This patchset was tested on MT8183 evaluation board and use correct clock to shell.
Based on v5.2-rc1
Change in v11:
New add spi node, efuse node, pinctrl node, auxadc node, and capacity-dmips-mhz field
Change in v10:
Add the L2 cache node to prevent warning on unable to detect cache hierarchy.
Change in v9:
Remove pio node since binding is not documented yet
Change in v8:
1. Fix interrupt-parent of pio node
2. Remove pinfunc.h and spi node patches
Change in v7:
1. Place all the MMIO peripherals under one or more simple-bus nodes
2. Make the pinfunc.h and spi node into seperate patch
3. Modify SPIs pamerater from 4 back to 3
and remove patch "support 4 interrupt parameters for sysirq"
4. Rename intpol-controller to interrupt-controller
5. Rename pinctrl@1000b000 to pinctrl@10005000
Change in v6:
1. Remove power and iommu nodes
2. Fix dtb build warning
3. Fix pinctrl binding doc
4. Fix '_' in node names
Change in v5:
1. Collect all device tree nodes to the last patch
2. Add PMU
3. Add Signed-off-by
4. Remove clock driver code and binding doc
5. Add pinctrl, iommu, spi, and pwrap nodes
Change in v4:
1. Correct syntax error in dtsi
2. Add MT8183 clock support
Change in v3:
1. Fill out GICC, GICH, GICV regions
2. Update Copyright to 2018
Change in v2:
1. Split dt-bindings into different patches
2. Correct bindings for supported SoCs (mtk-uart.txt)
Ben Ho (1):
arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and
Makefile
Erin Lo (1):
arm64: dts: mt8183: add spi node
Hsin-Yi, Wang (1):
arm64: dts: mt8183: add capacity-dmips-mhz
Michael Mei (1):
arm64: dts: mt8183: add efuse and Mediatek Chip id node to read
Zhiyong Tao (2):
arm64: dts: mt8183: add pinctrl device node
arm64: dts: mt8183: Add auxadc device node
arch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 140 ++++++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 447 ++++++++++++++++++++ 3 files changed, 588 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-evb.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8183.dtsi
--
1.8.1.1.dirty
PATCH v11 1/6 arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile
From: Ben Ho <[email protected]>
Add basic chip support for Mediatek 8183, include
uart node with correct uart clocks, pwrap device
Add clock controller nodes, include topckgen, infracfg, apmixedsys and subsystem.
--- arch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 31 +++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 311 ++++++++++++++++++++++++++++ 3 files changed, 343 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-evb.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8183.dtsi
arch/arm64/boot/dts/mediatek/Makefile +1 -0
@@ -7,3 +7,4 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
arch/arm64/boot/dts/mediatek/mt8183-evb.dts new file +31 -0
@@ -0,0 +1,31 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (c) 2018 MediaTek Inc. + * Author: Ben Ho <[email protected]> + * Erin Lo <[email protected]> + */ + +/dts-v1/; +#include "mt8183.dtsi" + +/ { + model = "MediaTek MT8183 evaluation board"; + compatible = "mediatek,mt8183-evb", "mediatek,mt8183"; + + aliases { + serial0 = &uart0; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0x80000000>; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; +}; + +&uart0 { + status = "okay"; +};
arch/arm64/boot/dts/mediatek/mt8183.dtsi new file +311 -0
311 lines not on this page · raw message
Signature · 1 line
1.8.1.1.dirty
PATCH v11 2/6 arm64: dts: mt8183: add capacity-dmips-mhz
In reply to Erin LoFrom: "Hsin-Yi, Wang" <[email protected]>
Pinned the frequency to the max and run dhrystone to get the value. little cpu: 11071 (max freq: 1989000)
big cpu: 15293 (max freq: 1989000)
11071 : 15293 ~= 741 : 1024
--- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/mediatek/mt8183.dtsi +8 -0
@@ -56,6 +56,7 @@ compatible = "arm,cortex-a53"; reg = <0x000>; enable-method = "psci"; + capacity-dmips-mhz = <741>; }; cpu1: cpu@1 {
@@ -63,6 +64,7 @@ compatible = "arm,cortex-a53"; reg = <0x001>; enable-method = "psci"; + capacity-dmips-mhz = <741>; }; cpu2: cpu@2 {
@@ -70,6 +72,7 @@ compatible = "arm,cortex-a53"; reg = <0x002>; enable-method = "psci"; + capacity-dmips-mhz = <741>; }; cpu3: cpu@3 {
@@ -77,6 +80,7 @@ compatible = "arm,cortex-a53"; reg = <0x003>; enable-method = "psci"; + capacity-dmips-mhz = <741>; }; cpu4: cpu@100 {
@@ -84,6 +88,7 @@ compatible = "arm,cortex-a73"; reg = <0x100>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; }; cpu5: cpu@101 {
@@ -91,6 +96,7 @@ compatible = "arm,cortex-a73"; reg = <0x101>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; }; cpu6: cpu@102 {
@@ -98,6 +104,7 @@ compatible = "arm,cortex-a73"; reg = <0x102>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; }; cpu7: cpu@103 {
@@ -105,6 +112,7 @@ compatible = "arm,cortex-a73"; reg = <0x103>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; }; };
Signature · 1 line
1.8.1.1.dirty
PATCH v11 3/6 arm64: dts: mt8183: add pinctrl device node
In reply to Erin LoFrom: Zhiyong Tao <[email protected]>
The commit adds pinctrl device node for mt8183
--- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+)
arch/arm64/boot/dts/mediatek/mt8183.dtsi +25 -0
@@ -8,6 +8,7 @@ #include <dt-bindings/clock/mt8183-clk.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> +#include "mt8183-pinfunc.h" / { compatible = "mediatek,mt8183";
@@ -204,6 +205,30 @@ #clock-cells = <1>; }; + pio: pinctrl@10005000 { + compatible = "mediatek,mt8183-pinctrl"; + reg = <0 0x10005000 0 0x1000>, + <0 0x11f20000 0 0x1000>, + <0 0x11e80000 0 0x1000>, + <0 0x11e70000 0 0x1000>, + <0 0x11e90000 0 0x1000>, + <0 0x11d30000 0 0x1000>, + <0 0x11d20000 0 0x1000>, + <0 0x11c50000 0 0x1000>, + <0 0x11f30000 0 0x1000>, + <0 0x1000b000 0 0x1000>; + reg-names = "iocfg0", "iocfg1", "iocfg2", + "iocfg3", "iocfg4", "iocfg5", + "iocfg6", "iocfg7", "iocfg8", + "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 192>; + interrupt-controller; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <2>; + }; + apmixedsys: syscon@1000c000 { compatible = "mediatek,mt8183-apmixedsys", "syscon"; reg = <0 0x1000c000 0 0x1000>;
Signature · 1 line
1.8.1.1.dirty
PATCH v11 4/6 arm64: dts: mt8183: Add auxadc device node
In reply to Erin LoFrom: Zhiyong Tao <[email protected]>
Add auxadc device node for MT8183
---
This patch is based on patch "https://patchwork.kernel.org/patch/10913941/".
--- arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 4 ++++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 10 ++++++++++ 2 files changed, 14 insertions(+)
arch/arm64/boot/dts/mediatek/mt8183-evb.dts +4 -0
@@ -26,6 +26,10 @@ }; }; +&auxadc { + status = "okay"; +}; + &uart0 { status = "okay"; };
arch/arm64/boot/dts/mediatek/mt8183.dtsi +10 -0
@@ -245,6 +245,16 @@ clock-names = "spi", "wrap"; }; + auxadc: auxadc@11001000 { + compatible = "mediatek,mt8183-auxadc", + "mediatek,mt8173-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&infracfg CLK_INFRA_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; + status = "disabled"; + }; + uart0: serial@11002000 { compatible = "mediatek,mt8183-uart", "mediatek,mt6577-uart";
Signature · 1 line
1.8.1.1.dirty
PATCH v11 5/6 arm64: dts: mt8183: add spi node
In reply to Erin LoAdd spi DTS node to the mt8183 and mt8183-evb.
--- arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 105 ++++++++++++++++++++++++++++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 78 +++++++++++++++++++++ 2 files changed, 183 insertions(+)
arch/arm64/boot/dts/mediatek/mt8183-evb.dts +105 -0
@@ -30,6 +30,111 @@ status = "okay"; }; +&pio { + spi_pins_0: spi0{ + pins_spi{ + pinmux = <PINMUX_GPIO85__FUNC_SPI0_MI>, + <PINMUX_GPIO86__FUNC_SPI0_CSB>, + <PINMUX_GPIO87__FUNC_SPI0_MO>, + <PINMUX_GPIO88__FUNC_SPI0_CLK>; + bias-disable; + }; + }; + + spi_pins_1: spi1{ + pins_spi{ + pinmux = <PINMUX_GPIO161__FUNC_SPI1_A_MI>, + <PINMUX_GPIO162__FUNC_SPI1_A_CSB>, + <PINMUX_GPIO163__FUNC_SPI1_A_MO>, + <PINMUX_GPIO164__FUNC_SPI1_A_CLK>; + bias-disable; + }; + }; + + spi_pins_2: spi2{ + pins_spi{ + pinmux = <PINMUX_GPIO0__FUNC_SPI2_CSB>, + <PINMUX_GPIO1__FUNC_SPI2_MO>, + <PINMUX_GPIO2__FUNC_SPI2_CLK>, + <PINMUX_GPIO94__FUNC_SPI2_MI>; + bias-disable; + }; + }; + + spi_pins_3: spi3{ + pins_spi{ + pinmux = <PINMUX_GPIO21__FUNC_SPI3_MI>, + <PINMUX_GPIO22__FUNC_SPI3_CSB>, + <PINMUX_GPIO23__FUNC_SPI3_MO>, + <PINMUX_GPIO24__FUNC_SPI3_CLK>; + bias-disable; + }; + }; + + spi_pins_4: spi4{ + pins_spi{ + pinmux = <PINMUX_GPIO17__FUNC_SPI4_MI>, + <PINMUX_GPIO18__FUNC_SPI4_CSB>, + <PINMUX_GPIO19__FUNC_SPI4_MO>, + <PINMUX_GPIO20__FUNC_SPI4_CLK>; + bias-disable; + }; + }; + + spi_pins_5: spi5{ + pins_spi{ + pinmux = <PINMUX_GPIO13__FUNC_SPI5_MI>, + <PINMUX_GPIO14__FUNC_SPI5_CSB>, + <PINMUX_GPIO15__FUNC_SPI5_MO>, + <PINMUX_GPIO16__FUNC_SPI5_CLK>; + bias-disable; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins_0>; + mediatek,pad-select = <0>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins_1>; + mediatek,pad-select = <0>; + status = "okay"; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins_2>; + mediatek,pad-select = <0>; + status = "okay"; +}; + +&spi3 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins_3>; + mediatek,pad-select = <0>; + status = "okay"; +}; + +&spi4 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins_4>; + mediatek,pad-select = <0>; + status = "okay"; +}; + +&spi5 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins_5>; + mediatek,pad-select = <0>; + status = "okay"; + +}; + &uart0 { status = "okay"; };
arch/arm64/boot/dts/mediatek/mt8183.dtsi +78 -0
84 lines not on this page · raw message
Signature · 1 line
1.8.1.1.dirty
PATCH v11 6/6 arm64: dts: mt8183: add efuse and Mediatek Chip id node to read
In reply to Erin LoFrom: Michael Mei <[email protected]>
support for reading chip ID and efuse
---
This patch is based on this patch:
https://patchwork.kernel.org/patch/10953029/
--- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
arch/arm64/boot/dts/mediatek/mt8183.dtsi +15 -0
@@ -156,6 +156,15 @@ compatible = "simple-bus"; ranges; + soc_data: soc_data@8000000 { + compatible = "mediatek,mt8183-efuse", + "mediatek,efuse"; + reg = <0 0x08000000 0 0x0010>; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + }; + gic: interrupt-controller@c000000 { compatible = "arm,gic-v3"; #interrupt-cells = <4>;
@@ -369,6 +378,12 @@ #clock-cells = <1>; }; + efuse: efuse@11f10000 { + compatible = "mediatek,mt8183-efuse", + "mediatek,efuse"; + reg = <0 0x11f10000 0 0x1000>; + }; + mfgcfg: syscon@13000000 { compatible = "mediatek,mt8183-mfgcfg", "syscon"; reg = <0 0x13000000 0 0x1000>;
Signature · 1 line
1.8.1.1.dirty
Matthias Brugger
maintainerQuoted 7 lines · Erin Lo
MT8183 is a SoC based on 64bit ARMv8 architecture.
It contains 4 CA53 and 4 CA73 cores.
MT8183 share many HW IP with MT65xx series.
This patchset was tested on MT8183 evaluation board and use correct clock to shell.Based on v5.2-rc1
Pushed all to v5.2-next/dts64
Please send patches to update the bindings of auxadc and efuse. They use the fallback right now, but we should make sure to have the binding in sync.
Regards,
Matthias
Quoted 74 lines
Change in v11:
New add spi node, efuse node, pinctrl node, auxadc node, and capacity-dmips-mhz fieldChange in v10:
Add the L2 cache node to prevent warning on unable to detect cache hierarchy.Change in v9:
Remove pio node since binding is not documented yetChange in v8:
1. Fix interrupt-parent of pio node
2. Removepinfunc.hand spi node patchesChange in v7:
1. Place all the MMIO peripherals under one or more simple-bus nodes
2. Make thepinfunc.hand spi node into seperate patch
3. Modify SPIs pamerater from 4 back to 3
and remove patch "support 4 interrupt parameters for sysirq"
4. Rename intpol-controller to interrupt-controller
5. Rename pinctrl@1000b000 to pinctrl@10005000Change in v6:
1. Remove power and iommu nodes
2. Fix dtb build warning
3. Fix pinctrl binding doc
4. Fix '_' in node namesChange in v5:
1. Collect all device tree nodes to the last patch
2. Add PMU
3. Add Signed-off-by
4. Remove clock driver code and binding doc
5. Add pinctrl, iommu, spi, and pwrap nodesChange in v4:
1. Correct syntax error in dtsi
2. Add MT8183 clock supportChange in v3:
1. Fill out GICC, GICH, GICV regions
2. Update Copyright to 2018Change in v2:
1. Split dt-bindings into different patches
2. Correct bindings for supported SoCs (mtk-uart.txt)Ben Ho (1):
arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and
MakefileErin Lo (1):
arm64: dts: mt8183: add spi nodeHsin-Yi, Wang (1):
arm64: dts: mt8183: add capacity-dmips-mhzMichael Mei (1):
arm64: dts: mt8183: add efuse and Mediatek Chip id node to readZhiyong Tao (2):
arm64: dts: mt8183: add pinctrl device node
arm64: dts: mt8183: Add auxadc device nodearch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 140 ++++++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 447 ++++++++++++++++++++ 3 files changed, 588 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-evb.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8183.dtsi--
1.8.1.1.dirty