Skip to contentSkip to conversation

405EP U-boot/Linux Question (CFG_OCM_DATA_ADDR)

U-Boot Pawel Pastuszak 2 participants 2 messages Jan 28, 2009 – Jan 29, 2009

lore
Share & tools
lore
#0 lore raw

Hi guys,

I was wondering if some one could give me an hand with OCM for PPC405EP

So my goal is to Access *CFG_BOOTCOUNT_ADDR *value in Linux based on
http://www.denx.de/wiki/view/DULG/UBootBootCountLimit

In u-boot it works fine but ... but how to i talk to this memory range in linux.

I tried the following but no luck.
ulong * save_addr = ioremap( (CFG_OCM_DATA_ADDR + CFG_BOOTCOUNT_ADDR),8
);

    if (save_addr[1] != BOOTCOUNT_MAGIC)
        return 0;
    else
        return save_addr[0];

u-boot config file setting:
#define *CFG_OCM_DATA_ADDR* 0xF8000000

#define CFG_OCM_DATA_SIZE   0x1000
#define CFG_INIT_RAM_ADDR   CFG_OCM_DATA_ADDR /* inside of OCM      */
#define CFG_INIT_RAM_END    CFG_OCM_DATA_SIZE /* End of used area in RAM

*/

#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data
*/
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) /* reserve some memory for POST and BOOT limit info */ #define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 24)

/* extra data in OCM */

#define CFG_POST_WORD_ADDR  (CFG_GBL_DATA_OFFSET - 4)
#define CFG_POST_MAGIC      (CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 8)
#define CFG_POST_VAL        (CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 12)

#ifdef CONFIG_BOOTCOUNT_LIMIT /* reserve 2 word for bootcount limit */ #define CFG_BOOTCOUNT_ADDR (CFG_GBL_DATA_OFFSET - 24) //#define *CFG_BOOTCOUNT_ADDR* (CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET -
16)
#endif

Any suggestion?

#1 lore raw
Quoted 4 lines · Pawel Pastuszak

I was wondering if some one could give me an hand with OCM for PPC405EP

So my goal is to Access *CFG_BOOTCOUNT_ADDR *value in Linux based on
http://www.denx.de/wiki/view/DULG/UBootBootCountLimit

Please note that its CONFIG_SYS_BOOTCOUNT_ADDR now.

Quoted 11 lines

In u-boot it works fine but ... but how to i talk to this memory range in linux.

I tried the following but no luck.
ulong * save_addr = ioremap( (CFG_OCM_DATA_ADDR + CFG_BOOTCOUNT_ADDR),8
);

    if (save_addr[1] != BOOTCOUNT_MAGIC)
        return 0;
    else
        return save_addr[0];

And what's the result of the above code? Do you get an exception? Or some unreasonable values?

Which kernel version are you using?

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================