Skip to contentSkip to conversation

Need help booting linux on 8265 eval board

U-Boot-Users   2 participants 2 messages Apr 18, 2004

lore
Share & tools
lore

 

author
#0 lore raw

Hi,
I have problem booting linux on 8265 eval board. when I boot the linux
kernel, the board be dead. the registers look like

to be some default values(use powertap pro). I try u-boot1.1, ppcboot1.1.5; linux kernel 2.4.4 2.4.18 2.4.20.

(1)about kernel
vim Makefile, arch=ppc CROSS_COMPILE=ppc_82xx
vim arch/ppc/platforms/ads826x.h, IMAP_ADDR=0x04700000 BCSR=0x04500000 then make mrproper/make ads826x_config/make oldconfig/make dep/make pImage (bd info struct is quite same between uboot and linux)

Is there anything I had ignored?

(2)let's see!(I add some "printf" to display values, "console=ttyS0,9600" is added)
=> bootm ffa00000 ffc00000
## Booting image at ffa00000 ...

   Image Name:   Linux-2.4.20-pre7ncsd1
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    634729 Bytes = 619 kB = 0 MB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Current stack ends at 0x03F7FC48 => set upper limit to 0x00800000 ## cmdline at 0x007FFF00 ... 0x007FFF23

memstart    = 0x00000000
memsize     = 0x04000000
flashstart  = 0xFF800000
flashsize   = 0x00800000
flashoffset = 0x00000000
sramstart   = 0x00000000
sramsize    = 0x00000000
immr_base   = 0x04700000
bootflags   = 0x00000001
vco         = 266.666 MHz
sccfreq     = 66.666 MHz
brgfreq     = 16.666 MHz
intfreq     = 166.666 MHz
cpmfreq     = 133.333 MHz
busfreq     = 33.333 MHz
ethaddr     = 00:10:EC:00:30:8C
IP addr     = 8.6.0.1
baudrate    =   9600 bps
## Loading RAMDisk Image at ffc00000 ...
   Image Name:   Simple Ramdisk-Image
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    567988 Bytes = 554 kB = 0 MB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## initrd at 0xFFC00040 ... 0xFFC8AAF3 (len=567988=0x8AAB4)
Loading Ramdisk to 03ef4000, end 03f7eab4 ... OK
## Transferring control to Linux (at address 00000000) ...

then the board is dead and the LED(FCC link) coruscate . (I have modified clock calculations for this board. it's the reason?) any ideas? thanks a lot!

--
liu
liutomorrow at hotmail.com

_________________________________________________________________
???? MSN Explorer: http://explorer.msn.com/lccn/

#1 lore raw
Quoted 4 lines · In message <[email protected]> you wrote:

I have problem booting linux on 8265 eval board. when I boot the linux
kernel, the board be dead. the registers look like
to be some default values(use powertap pro). I try u-boot1.1, ppcboot1.1.5;

Be careful. User the default values as defined in U-Boot and Linux, and DON'T change these unless you know EXACTLY what you are doing.

Quoted 2 lines

vim Makefile, arch=ppc CROSS_COMPILE=ppc_82xx
vim arch/ppc/platforms/ads826x.h, IMAP_ADDR=0x04700000 BCSR=0x04500000

This cannot work. Please leave the mapping as defined by U-Boot and Linux.

Quoted 4 lines

then the board is dead and the LED(FCC link) coruscate . (I have modified clock calculations for this board. it's the reason?) any ideas? thanks a lot!

You seem to modify a lot of stuff without konwing exactly why - don;t do this. The default values are there for a reason - they are known to work.

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-4596-87  Fax: (+49)-8142-4596-88  Email: wd at denx.de
"There are three principal ways to lose money: wine, women, and engi-
neers. While the first two are more pleasant, the third is by far the
more certain."                           - Baron Rothschild, ca. 1800