hw/isa/piix4: Remove MIPS Malta specific bits
v2 cover hw/isa/piix4: Remove MIPS Malta specific bits
Since v1:
- bswap -> tswap (Bernhard)
Bernhard posted a series merging both PIIX3/PIIX4 models in one [1]. Due to Malta-specific board code forced into the PIIX4 reset values, Bernhard had to include an array of "register values at reset" as a class property. This is not wrong, but to model properly the model, we should simply use the hardware real reset values, not try to bend the model to please the Malta board.
This series fix this issue by having the Malta bootloader code setting the board-specific PIIX4 IRQ routing values.
Note patch 2 still misses an equivalent nanoMIPS code.
Regards,
Phil.
[1] https://lore.kernel.org/qemu-devel/[email protected]/
Based-on: <[email protected]>
https://lore.kernel.org/qemu-devel/[email protected]/
Philippe Mathieu-Daudé (3):
hw/mips/malta: Introduce PIIX4_PCI_DEVFN definition hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader hw/isa/piix4: Correct IRQRC[A:D] reset values
hw/isa/piix4.c | 8 ++++---- hw/mips/malta.c | 23 ++++++++++++++++++++++- 2 files changed, 26 insertions(+), 5 deletions(-)
Signature · 1 line
2.37.3
PATCH v2 1/3 hw/mips/malta: Introduce PIIX4_PCI_DEVFN definition
The PIIX4 PCI-ISA bridge function is always located at 10:0. Since we want to re-use its address, add the PIIX4_PCI_DEVFN definition.
--- hw/mips/malta.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
hw/mips/malta.c +3 -1
@@ -72,6 +72,8 @@#define MAX_IDE_BUS 2 +#define PIIX4_PCI_DEVFN PCI_DEVFN(10, 0) + typedef struct { MemoryRegion iomem; MemoryRegion iomem_lo; /* 0 - 0x900 */
@@ -1377,7 +1379,7 @@ void mips_malta_init(MachineState *machine)empty_slot_init ("GT64120" ,0 ,0x20000000 );/* Southbridge */ - piix4 =pci_create_simple_multifunction (pci_bus,PCI_DEVFN (10 ,0 ), true, + piix4 =pci_create_simple_multifunction (pci_bus,PIIX4_PCI_DEVFN , true,TYPE_PIIX4_PCI_DEVICE ); dev =DEVICE (piix4); isa_bus =ISA_BUS (qdev_get_child_bus (dev,"isa.0" ));
Signature · 1 line
2.37.3
Re: [PATCH v2 1/3] hw/mips/malta: Introduce PIIX4_PCI_DEVFN definition
Am 27. Oktober 2022 20:47:18 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 6 lines
The PIIX4 PCI-ISA bridge function is always located at 10:0. Since we want to re-use its address, add the
PIIX4_PCI_DEVFNdefinition.Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
Quoted 25 lines
hw/mips/malta.c| 4 +++-1 file changed, 3 insertions(+), 1 deletion(-)hw/mips/malta.c +3
-1@@ -72,6 +72,8 @@#define MAX_IDE_BUS 2 +#define PIIX4_PCI_DEVFN PCI_DEVFN(10, 0) + typedef struct { MemoryRegion iomem; MemoryRegion iomem_lo; /* 0 - 0x900 */@@ -1377,7 +1379,7 @@ void mips_malta_init(MachineState *machine)empty_slot_init ("GT64120" ,0 ,0x20000000 );/* Southbridge */ - piix4 =pci_create_simple_multifunction (pci_bus,PCI_DEVFN (10 ,0 ), true, + piix4 =pci_create_simple_multifunction (pci_bus,PIIX4_PCI_DEVFN , true,TYPE_PIIX4_PCI_DEVICE ); dev =DEVICE (piix4); isa_bus =ISA_BUS (qdev_get_child_bus (dev,"isa.0" ));
PATCH v2 2/3 hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
In reply to Philippe Mathieu-DaudéLinux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in write_bootloader().
Upon introduction in commit 5c2b87e34d ("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.
Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
---
FIXME: Missing the nanoMIPS counter-part!
--- hw/mips/malta.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
hw/mips/malta.c +19 -0
@@ -804,6 +804,8 @@ static void write_bootloader_nanomips(uint8_t *base, uint64_t run_addr,stw_p (p++,0x8422 );stw_p (p++,0x9088 );/* sw t0, 0x88(t1) */ +/* TODO set PIIX IRQC[A:D] routing values! */ +stw_p (p++,0xe320 |NM_HI1 (kernel_entry));stw_p (p++,NM_HI2 (kernel_entry));
@@ -841,6 +843,9 @@ static void write_bootloader_nanomips(uint8_t *base, uint64_t run_addr,static void write_bootloader (uint8_t *base,uint64_t run_addr,uint64_t kernel_entry) { +const char pci_pins_cfg[PCI_NUM_PINS ] = { +10 ,10 ,11 ,11 /* PIIX IRQRC[A:D] */ + };uint32_t *p;/* Small bootloader */
@@ -915,6 +920,20 @@ static void write_bootloader(uint8_t *base, uint64_t run_addr,#undef cpu_to_gt32 +/* +* The PIIX ISA bridge is on PCI bus 0 dev 10 func 0. +* Load the PIIX IRQC[A:D] routing config address, then +* write routing configuration to the config data register. +*/ +bl_gen_write_u32 (&p,/* GT_PCI0_CFGADDR */ +cpu_mips_phys_to_kseg1 (NULL ,0x1be00000 +0xcf8 ), +tswap32 ((1 <<31 )/* ConfigEn */ + |PCI_BUILD_BDF (0 ,PIIX4_PCI_DEVFN ) <<8 + |PIIX_PIRQCA )); +bl_gen_write_u32 (&p,/* GT_PCI0_CFGDATA */ +cpu_mips_phys_to_kseg1 (NULL ,0x1be00000 +0xcfc ), +tswap32 (ldl_be_p (pci_pins_cfg))); + bl_gen_jump_kernel(&p, true, ENVP_VADDR - 64,/*
Signature · 1 line
2.37.3
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 8 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.
Quoted 8 lines
Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!
Who will be taking care of this? I have absolutely no clue how the write_bootloader functions work, so I don't see how to fix it.
Couldn't we just do it like in pegasos2_init() where the registers are initialized by QEMU directly if there is no bootloader binary configured? I could do that.
Best regards,
Bernhard
Quoted 48 lines
---
hw/mips/malta.c| 19 +++++++++++++++++++1 file changed, 19 insertions(+)hw/mips/malta.c +19
-0@@ -804,6 +804,8 @@ static void write_bootloader_nanomips(uint8_t *base, uint64_t run_addr,stw_p (p++,0x8422 );stw_p (p++,0x9088 );/* sw t0, 0x88(t1) */ +/* TODO set PIIX IRQC[A:D] routing values! */ +stw_p (p++,0xe320 |NM_HI1 (kernel_entry));stw_p (p++,NM_HI2 (kernel_entry));@@ -841,6 +843,9 @@ static void write_bootloader_nanomips(uint8_t *base, uint64_t run_addr,static void write_bootloader (uint8_t *base,uint64_t run_addr,uint64_t kernel_entry) { +const char pci_pins_cfg[PCI_NUM_PINS ] = { +10 ,10 ,11 ,11 /* PIIX IRQRC[A:D] */ + };uint32_t *p;/* Small bootloader */ @@ -915,6 +920,20 @@ static void write_bootloader(uint8_t *base, uint64_t run_addr,#undef cpu_to_gt32 +/* +* The PIIX ISA bridge is on PCI bus 0 dev 10 func 0. +* Load the PIIX IRQC[A:D] routing config address, then +* write routing configuration to the config data register. +*/ +bl_gen_write_u32 (&p,/* GT_PCI0_CFGADDR */ +cpu_mips_phys_to_kseg1 (NULL ,0x1be00000 +0xcf8 ), +tswap32 ((1 <<31 )/* ConfigEn */ + |PCI_BUILD_BDF (0 ,PIIX4_PCI_DEVFN ) <<8 + |PIIX_PIRQCA )); +bl_gen_write_u32 (&p,/* GT_PCI0_CFGDATA */ +cpu_mips_phys_to_kseg1 (NULL ,0x1be00000 +0xcfc ), +tswap32 (ldl_be_p (pci_pins_cfg))); + bl_gen_jump_kernel(&p, true, ENVP_VADDR - 64,/*
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Quoted 16 lines · Bernhard Beschow
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 13 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Quoted 5 lines
Quoted 3 lines
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.
Oh actually I wrote that and tested it but context switched and forgot about it... I'll look back when I get some time, probably around the release.
Quoted 1 line
Couldn't we just do it like in
pegasos2_init()where the registers are initialized by QEMU directly if there is no bootloader binary configured? I could do that.
I rather mimic bootloaders... maybe a matter of taste?
Regards,
Phil.
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Am 21. November 2022 22:43:50 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 21 lines · Bernhard Beschow
Quoted 20 lines
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 16 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!
Quoted 8 lines
Quoted 1 line
Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.Oh actually I wrote that and tested it but context switched and forgot about it... I'll look back when I get some time, probably around the release.
Quoted 1 line
Couldn't we just do it like in
pegasos2_init()where the registers are initialized by QEMU directly if there is no bootloader binary configured? I could do that.I rather mimic bootloaders... maybe a matter of taste?
I don't mind either way. I meant that I could help with the second approach but not with the current one since I have no clue whatsoever how it works. There are just too many magic constants that don't make any sense to me, and too many layers of indirection, for example.
Anyway, I'm asking for the current state because I'm pretty much ready for posting a v3 of my PIIX consolidation series which now depends on this series.
Best regards,
Bernhard
Quoted 4 lines
Regards,
Phil.
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Hello,
Quoted 25 lines · Bernhard Beschow
Am 21. November 2022 22:43:50 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 24 lines · Bernhard Beschow
Quoted 14 lines
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 13 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Quoted 5 lines
Quoted 3 lines
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.Oh actually I wrote that and tested it but context switched and forgot about it... I'll look back when I get some time, probably around the release.
Unrelated to this but found it while looking at malta.c now: another possible clean up is to replace the local generate_eeprom_spd() func with spd_data_generate() from hw/i2c/smbus_eeprom.c that other boards use already but I did not change malta because I could not test it. If you can test malta then it should be an easy change and simplify malta.c a bit.
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
Couldn't we just do it like in
pegasos2_init()where the registers are initialized by QEMU directly if there is no bootloader binary configured? I could do that.I rather mimic bootloaders... maybe a matter of taste?
Is that a bootloader or a replacement firmware? To me bootloader is some OS specific binary that is loaded by firware to boot an OS. But there are OS independent bootloaders like grub so maybe you could emulate something like that, I don't know what malta does.
If there's no firmware binary QEMU should provide something to replace it to give the expected environment for the binary loaded by -kernel. In case of pegasos2 the init method sets up regs to init devices as done by the firmware and the rest is implemented by VOF (loaded from pc-bios) that provices the OpenFirmware client interface. The device setup in init is needed because VOF does not do that.
Quoted 1 line
I don't mind either way. I meant that I could help with the second approach but not with the current one since I have no clue whatsoever how it works. There are just too many magic constants that don't make any sense to me, and too many layers of indirection, for example.
If malta has a replacement firmware for this case maybe it could be stored in a binary in pc-bios and loaded from there instead of writing it in hex to guest memory. That binary could even be assembled from source which should make it simpler to write and change. Or is YAMON open source? According to this page it is: https://www.mips.com/develop/tools/boot-loaders/ so maybe it could be included as a firmware binary instead of being emulated?
Regards,
BALATON Zoltan
Quoted 11 lines
Anyway, I'm asking for the current state because I'm pretty much ready for posting a v3 of my PIIX consolidation series which now depends on this series.
Best regards,
BernhardQuoted 4 lines
Regards,
Phil.
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Quoted 32 lines
2022年11月22日 12:37,BALATON Zoltan <[email protected]> 写道:
Hello,
Quoted 25 lines · Bernhard Beschow
Am 21. November 2022 22:43:50 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 24 lines · Bernhard Beschow
Quoted 14 lines
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 13 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Quoted 5 lines
Quoted 3 lines
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.Oh actually I wrote that and tested it but context switched and forgot about it... I'll look back when I get some time, probably around the release.
I can try to adopt existing boot loader helper functions, just a matter of opcodes I think.
Quoted 7 lines
Unrelated to this but found it while looking at
malta.cnow: another possible clean up is to replace the localgenerate_eeprom_spd()func withspd_data_generate()fromhw/i2c/smbus_eeprom.cthat other boards use already but I did not change malta because I could not test it. If you can test malta then it should be an easy change and simplifymalta.ca bit.Quoted 2 lines
Quoted 2 lines
Quoted 1 line
Couldn't we just do it like in
pegasos2_init()where the registers are initialized by QEMU directly if there is no bootloader binary configured? I could do that.I rather mimic bootloaders... maybe a matter of taste?
Is that a bootloader or a replacement firmware? To me bootloader is some OS specific binary that is loaded by firware to boot an OS. But there are OS independent bootloaders like grub so maybe you could emulate something like that, I don't know what malta does.
YAMON is a OS-dependent and HW-dependent firmware like u-boot.
Quoted 6 lines
If there's no firmware binary QEMU should provide something to replace it to give the expected environment for the binary loaded by -kernel. In case of pegasos2 the init method sets up regs to init devices as done by the firmware and the rest is implemented by VOF (loaded from pc-bios) that provices the OpenFirmware client interface. The device setup in init is needed because VOF does not do that.
Quoted 1 line
I don't mind either way. I meant that I could help with the second approach but not with the current one since I have no clue whatsoever how it works. There are just too many magic constants that don't make any sense to me, and too many layers of indirection, for example.
If malta has a replacement firmware for this case maybe it could be stored in a binary in pc-bios and loaded from there instead of writing it in hex to guest memory. That binary could even be assembled from source which should make it simpler to write and change. Or is YAMON open source? According to this page it is: https://www.mips.com/develop/tools/boot-loaders/ so maybe it could be included as a firmware binary instead of being emulated?
Hmm, YAMON was a open source software but I’m unable to find a copy of source for Malta board comes with GT chipset that QEMU emulated. So nowadays we mainly use -kernel feature to do direct kernel boot.
Direct kernel boot is really a brilliant function that I don’t want to lose :-)
Thanks
- Jiaxun
Quoted 14 lines
Regards,
BALATON ZoltanQuoted 10 lines
Anyway, I'm asking for the current state because I'm pretty much ready for posting a v3 of my PIIX consolidation series which now depends on this series.
Best regards,
BernhardQuoted 4 lines
Regards,
Phil.
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
In reply to Bernhard BeschowAm 21. November 2022 15:34:05 UTC schrieb Bernhard Beschow <[email protected]>:
Quoted 16 lines
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 13 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Quoted 5 lines
Quoted 3 lines
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.
Ping
Quoted 52 lines
Couldn't we just do it like in
pegasos2_init()where the registers are initialized by QEMU directly if there is no bootloader binary configured? I could do that.Best regards,
BernhardQuoted 48 lines
---
hw/mips/malta.c| 19 +++++++++++++++++++1 file changed, 19 insertions(+)hw/mips/malta.c +19
-0@@ -804,6 +804,8 @@ static void write_bootloader_nanomips(uint8_t *base, uint64_t run_addr,stw_p (p++,0x8422 );stw_p (p++,0x9088 );/* sw t0, 0x88(t1) */ +/* TODO set PIIX IRQC[A:D] routing values! */ +stw_p (p++,0xe320 |NM_HI1 (kernel_entry));stw_p (p++,NM_HI2 (kernel_entry));@@ -841,6 +843,9 @@ static void write_bootloader_nanomips(uint8_t *base, uint64_t run_addr,static void write_bootloader (uint8_t *base,uint64_t run_addr,uint64_t kernel_entry) { +const char pci_pins_cfg[PCI_NUM_PINS ] = { +10 ,10 ,11 ,11 /* PIIX IRQRC[A:D] */ + };uint32_t *p;/* Small bootloader */ @@ -915,6 +920,20 @@ static void write_bootloader(uint8_t *base, uint64_t run_addr,#undef cpu_to_gt32 +/* +* The PIIX ISA bridge is on PCI bus 0 dev 10 func 0. +* Load the PIIX IRQC[A:D] routing config address, then +* write routing configuration to the config data register. +*/ +bl_gen_write_u32 (&p,/* GT_PCI0_CFGADDR */ +cpu_mips_phys_to_kseg1 (NULL ,0x1be00000 +0xcf8 ), +tswap32 ((1 <<31 )/* ConfigEn */ + |PCI_BUILD_BDF (0 ,PIIX4_PCI_DEVFN ) <<8 + |PIIX_PIRQCA )); +bl_gen_write_u32 (&p,/* GT_PCI0_CFGDATA */ +cpu_mips_phys_to_kseg1 (NULL ,0x1be00000 +0xcfc ), +tswap32 (ldl_be_p (pci_pins_cfg))); + bl_gen_jump_kernel(&p, true, ENVP_VADDR - 64,/*
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Quoted 19 lines · Bernhard Beschow
Am 21. November 2022 15:34:05 UTC schrieb Bernhard Beschow <[email protected]>:
Quoted 16 lines
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 13 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.Ping
This comment has been taken care of:
https://lore.kernel.org/qemu-devel/[email protected]/
However while testing the MIPS pull request I prepared I found a bug in the GT64120 which I'm trying to fix since various days... Unfortunately your series depends on it, so this is a blocking issue. Sorry for this long delay...
Phil.
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Am 31. Dezember 2022 13:44:00 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 24 lines · Bernhard Beschow
Quoted 23 lines
Am 21. November 2022 15:34:05 UTC schrieb Bernhard Beschow <[email protected]>:
Quoted 20 lines
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 16 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.Ping
This comment has been taken care of:
https://lore.kernel.org/qemu-devel/[email protected]/
Ah, now I see where this is going.
Quoted 4 lines
However while testing the MIPS pull request I prepared I found a bug in the GT64120 which I'm trying to fix since various days... Unfortunately your series depends on it, so this is a blocking issue. Sorry for this long delay...
Don't worry.
How can the bug be reproduced? Is there a test run in the CI? Note that I get a 404 when trying to access https://gitlab.com/philmd/qemu/-/commits/mips-testing/ .
Best regards,
Bernhard
Quoted 2 lines
Phil.
Re: [PATCH v2 2/3] hw/mips/malta: Set PIIX4 IRQ routes in embedded bootloader
Quoted 36 lines · Bernhard Beschow
Am 31. Dezember 2022 13:44:00 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 24 lines · Bernhard Beschow
Quoted 23 lines
Am 21. November 2022 15:34:05 UTC schrieb Bernhard Beschow <[email protected]>:
Quoted 20 lines
Am 27. Oktober 2022 20:47:19 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 16 lines
Linux kernel expects the northbridge & southbridge chipsets configured by the BIOS firmware. We emulate that by writing a tiny bootloader code in
write_bootloader().Upon introduction in commit
5c2b87e34d("PIIX4 support"), the PIIX4 configuration space included values specific to the Malta board.Set the Malta-specific IRQ routing values in the embedded bootloader, so the next commit can remove the Malta specific bits from the PIIX4 PCI-ISA bridge and make it generic (matching the real hardware).
Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
FIXME: Missing the nanoMIPS counter-part!Quoted 6 lines
Quoted 3 lines
Quoted 1 line
Who will be taking care of this? I have absolutely no clue how the
write_bootloaderfunctions work, so I don't see how to fix it.Ping
This comment has been taken care of:
https://lore.kernel.org/qemu-devel/[email protected]/Ah, now I see where this is going.
Quoted 8 lines
Quoted 4 lines
However while testing the MIPS pull request I prepared I found a bug in the GT64120 which I'm trying to fix since various days... Unfortunately your series depends on it, so this is a blocking issue. Sorry for this long delay...
Don't worry.
How can the bug be reproduced? Is there a test run in the CI?
My problem was on big-endian hosts, now fixed by:
https://lore.kernel.org/qemu-devel/[email protected]/
Quoted 1 line
Note that I get a 404 when trying to access https://gitlab.com/philmd/qemu/-/commits/mips-testing/ .
Oh for some reason my repository was set for 'project members', I now changed that to 'everyone'.
I'll rebuild the mips-testing queue later today or tomorrow and restart my testing.
Regards,
Phil.
PATCH v2 3/3 hw/isa/piix4: Correct IRQRC[A:D] reset values
In reply to Philippe Mathieu-DaudéIRQRC[A:D] registers reset value is 0x80. We were forcing the MIPS Malta machine routing to be able to boot a Linux kernel without any bootloader.
We now have these registers initialized in the Malta machine write_bootloader(), so we can use the correct reset values.
--- hw/isa/piix4.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
hw/isa/piix4.c +4 -4
@@ -115,10 +115,10 @@ static void piix4_isa_reset(DeviceState *dev) pci_conf[0x4c ] =0x4d ; pci_conf[0x4e ] =0x03 ; pci_conf[0x4f ] =0x00 ; - pci_conf[0x60 ] =0x0a ;// PCI A -> IRQ 10 - pci_conf[0x61 ] =0x0a ;// PCI B -> IRQ 10 - pci_conf[0x62 ] =0x0b ;// PCI C -> IRQ 11 - pci_conf[0x63 ] =0x0b ;// PCI D -> IRQ 11 + pci_conf[0x60 ] =0x80 ; + pci_conf[0x61 ] =0x80 ; + pci_conf[0x62 ] =0x80 ; + pci_conf[0x63 ] =0x80 ; pci_conf[0x69 ] =0x02 ; pci_conf[0x70 ] =0x80 ; pci_conf[0x76 ] =0x0c ;
Signature · 1 line
2.37.3
Re: [PATCH v2 3/3] hw/isa/piix4: Correct IRQRC[A:D] reset values
Am 27. Oktober 2022 20:47:20 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 8 lines
IRQRC[A:D] registers reset value is
0x80. We were forcing the MIPS Malta machine routing to be able to boot a Linux kernel without any bootloader.
We now have these registers initialized in the Malta machinewrite_bootloader(), so we can use the correct reset values.Signed-off-by Philippe Mathieu-Daudé <[email protected]>---
Quoted 22 lines
hw/isa/piix4.c| 8 ++++----1 file changed, 4 insertions(+), 4 deletions(-)hw/isa/piix4.c +4
-4@@ -115,10 +115,10 @@ static void piix4_isa_reset(DeviceState *dev) pci_conf[0x4c ] =0x4d ; pci_conf[0x4e ] =0x03 ; pci_conf[0x4f ] =0x00 ; - pci_conf[0x60 ] =0x0a ;// PCI A -> IRQ 10 - pci_conf[0x61 ] =0x0a ;// PCI B -> IRQ 10 - pci_conf[0x62 ] =0x0b ;// PCI C -> IRQ 11 - pci_conf[0x63 ] =0x0b ;// PCI D -> IRQ 11 + pci_conf[0x60 ] =0x80 ; + pci_conf[0x61 ] =0x80 ; + pci_conf[0x62 ] =0x80 ; + pci_conf[0x63 ] =0x80 ; pci_conf[0x69 ] =0x02 ; pci_conf[0x70 ] =0x80 ; pci_conf[0x76 ] =0x0c ;
Re: [PATCH v2 3/3] hw/isa/piix4: Correct IRQRC[A:D] reset values
In reply to Philippe Mathieu-DaudéAm 27. Oktober 2022 20:47:20 UTC schrieb "Philippe Mathieu-Daudé" <[email protected]>:
Quoted 7 lines
IRQRC[A:D] registers reset value is
0x80. We were forcing the MIPS Malta machine routing to be able to boot a Linux kernel without any bootloader.
We now have these registers initialized in the Malta machinewrite_bootloader(), so we can use the correct reset values.Signed-off-by Philippe Mathieu-Daudé <[email protected]>
https://lists.nongnu.org/archive/html/qemu-devel/2022-12/msg03048.html :
Quoted 23 lines
---
hw/isa/piix4.c| 8 ++++----1 file changed, 4 insertions(+), 4 deletions(-)hw/isa/piix4.c +4
-4@@ -115,10 +115,10 @@ static void piix4_isa_reset(DeviceState *dev) pci_conf[0x4c ] =0x4d ; pci_conf[0x4e ] =0x03 ; pci_conf[0x4f ] =0x00 ; - pci_conf[0x60 ] =0x0a ;// PCI A -> IRQ 10 - pci_conf[0x61 ] =0x0a ;// PCI B -> IRQ 10 - pci_conf[0x62 ] =0x0b ;// PCI C -> IRQ 11 - pci_conf[0x63 ] =0x0b ;// PCI D -> IRQ 11 + pci_conf[0x60 ] =0x80 ; + pci_conf[0x61 ] =0x80 ; + pci_conf[0x62 ] =0x80 ; + pci_conf[0x63 ] =0x80 ; pci_conf[0x69 ] =0x02 ; pci_conf[0x70 ] =0x80 ; pci_conf[0x76 ] =0x0c ;
Quoted 11 lines · Philippe Mathieu-Daudé
Since v1:
- bswap -> tswap (Bernhard)Bernhard posted a series merging both PIIX3/PIIX4 models in one [1]. Due to Malta-specific board code forced into the PIIX4 reset values, Bernhard had to include an array of "register values at reset" as a class property. This is not wrong, but to model properly the model, we should simply use the hardware real reset values, not try to bend the model to please the Malta board.
Quoted 4 lines
This series fix this issue by having the Malta bootloader code setting the board-specific PIIX4 IRQ routing values.
Note patch 2 still misses an equivalent nanoMIPS code.
So this series won't be merged until this is added, but it should be enough to let Bernhard keep working on the "Consolidate PIIX series".