Skip to contentSkip to conversation

Access VNC Server via DNAT

DISCUSSION Joel Pearson 3 participants 4 messages Sep 20, 2003 – Sep 23, 2003

lore
Share & tools
lore
#0 lore raw

Hey,

I have a vnc server that is on my local lan at home that I'd like to be able to access from the internet via my internet gateway linux box. I've read a little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s 192.168.0.2 -j DNAT --to 192.168.0.25:5904
But it says it can't connect to the server. At the moment I'm just trying to get the port forwarding to work on my local lan, but it doesn't seem to be working. I've read of people haveing this working using a somewhat similar iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a

Does anyone know why this isn't working?

Thanks

Joel

#1 lore raw

----- Original Message -----
From: "Joel Pearson" <[email protected]>
To: <[email protected]>
Sent: Saturday, September 20, 2003 7:26 PM
Subject: Access VNC Server via DNAT

Quoted 3 lines

Hey,

I have a vnc server that is on my local lan at home that I'd like to be

able

Quoted 1 line

to access from the internet via my internet gateway linux box. I've read

a

Quoted 3 lines

little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s

192.168.0.2 -j

Quoted 1 line

DNAT --to 192.168.0.25:5904

If your internet interface is eth0, you need to do /sbin/iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -j DNAT --to-destination 192.168.0.25

Please note the above rule will allow you to connect only from internet.

Quoted 1 line

But it says it can't connect to the server. At the moment I'm just trying

to

Quoted 11 lines

get the port forwarding to work on my local lan, but it doesn't seem to be working. I've read of people haveing this working using a somewhat similar iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a

Does anyone know why this isn't working?

Thanks

Joel

Venkatesh K

#2 lore raw

Hey,

Thanks for your help, I managed to get it working in the end, one of my problems as you said was that the rule only worked from the internet (when I was testing at home), and I somehow managed to screw my firewall rules so that when I tried the DNAT thing at work and tried to access from home it was dropping packets.
Restarted iptables then everything was happy, so I don't really know how long it was actually working for, but its working now so I'm happy :-)

Thanks

Joel
"Venkatesh. K" <[email protected]> wrote in message news:012d01c380e0$0b35f120$2800a8c0@karu...

Quoted 7 lines

----- Original Message -----
From: "Joel Pearson" <[email protected]>
To: <[email protected]>
Sent: Saturday, September 20, 2003 7:26 PM
Subject: Access VNC Server via DNAT

Quoted 5 lines
Quoted 3 lines

Hey,

I have a vnc server that is on my local lan at home that I'd like to be

able

Quoted 1 line

to access from the internet via my internet gateway linux box. I've

read

Quoted 4 lines

a

Quoted 3 lines

little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s

Quoted 10 lines

192.168.0.2 -j

Quoted 1 line

DNAT --to 192.168.0.25:5904

If your internet interface is eth0, you need to do /sbin/iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -j DNAT --to-destination 192.168.0.25

Please note the above rule will allow you to connect only from internet.

Quoted 1 line

But it says it can't connect to the server. At the moment I'm just

trying

Quoted 2 lines

to

Quoted 1 line

get the port forwarding to work on my local lan, but it doesn't seem to

be

Quoted 1 line
Quoted 1 line

working. I've read of people haveing this working using a somewhat

similar

Quoted 14 lines
Quoted 9 lines

iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a

Does anyone know why this isn't working?

Thanks

Joel

Venkatesh K

#3 lore raw
In reply to Joel Pearson

Other than connection tracking, if you are using stateful, there are not any special modules needed. I will also add, allowing VNC to penetrate the firewall is not the best of ideas, but very possible to do it securely if you are smart and crafty about it. Here are a couple of thoughts which should help you. First, confirm what port your VNC server is Listening on. The VNC port range is: VNC_PORTS="5900:5910". So, take a look at this.

Having said that, it will also take a minimum of two rules to penetrate the firewall. 1) DNAT correct listening port through to the correct server as you have done with:

iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 59xx -s 192.168.0.2 -j DNAT --to 192.168.0.25:59xx

That's only half of it. You must then accept the packet once it is has been DNATTED, such as:

$IPT -t filter -A FORWARD -i $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j LOG --log-prefix "ACCEPT INBOUND VNC: " $IPT -t filter -A FORWARD -i $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j ACCEPT
$IPT -t filter -A FORWARD -o $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j LOG --log-prefix "ACCEPT OUTBOUND VNC: " $IPT -t filter -A FORWARD -o $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j ACCEPT

Additionally, if you are using connection tracking, you must ACCEPT as ESTABLISHED and RELATED as well. Hope this helps.

-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Joel Pearson
Sent: Saturday, September 20, 2003 6:57 AM
To: [email protected]
Subject: Access VNC Server via DNAT

Hey,

I have a vnc server that is on my local lan at home that I'd like to be able to access from the internet via my internet gateway linux box. I've read a little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s 192.168.0.2 -j DNAT --to 192.168.0.25:5904
But it says it can't connect to the server. At the moment I'm just trying to get the port forwarding to work on my local lan, but it doesn't seem to be working. I've read of people haveing this working using a somewhat similar iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a

Does anyone know why this isn't working?

Thanks

Joel