Access VNC Server via DNAT
Hey,
I have a vnc server that is on my local lan at home that I'd like to be able to access from the internet via my internet gateway linux box. I've read a little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s 192.168.0.2 -j DNAT --to 192.168.0.25:5904
But it says it can't connect to the server. At the moment I'm just trying to get the port forwarding to work on my local lan, but it doesn't seem to be working. I've read of people haveing this working using a somewhat similar iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a
Does anyone know why this isn't working?
Thanks
Joel
----- Original Message -----
From: "Joel Pearson" <[email protected]>
To: <[email protected]>
Sent: Saturday, September 20, 2003 7:26 PM
Subject: Access VNC Server via DNAT
Quoted 3 lines
Hey,
I have a vnc server that is on my local lan at home that I'd like to be
able
Quoted 1 line
to access from the internet via my internet gateway linux box. I've read
a
Quoted 3 lines
little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s
192.168.0.2 -j
Quoted 1 line
DNAT --to 192.168.0.25:5904
If your internet interface is eth0, you need to do /sbin/iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -j DNAT --to-destination 192.168.0.25
Please note the above rule will allow you to connect only from internet.
Quoted 1 line
But it says it can't connect to the server. At the moment I'm just trying
to
Quoted 11 lines
get the port forwarding to work on my local lan, but it doesn't seem to be working. I've read of people haveing this working using a somewhat similar iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a
Does anyone know why this isn't working?
Thanks
Joel
Venkatesh K
Hey,
Thanks for your help, I managed to get it working in the end, one of my problems as you said was that the rule only worked from the internet (when I was testing at home), and I somehow managed to screw my firewall rules so that when I tried the DNAT thing at work and tried to access from home it was dropping packets.
Restarted iptables then everything was happy, so I don't really know how long it was actually working for, but its working now so I'm happy :-)
Thanks
Joel
"Venkatesh. K" <[email protected]> wrote in message news:012d01c380e0$0b35f120$2800a8c0@karu...
Quoted 7 lines
----- Original Message -----
From: "Joel Pearson" <[email protected]>
To: <[email protected]>
Sent: Saturday, September 20, 2003 7:26 PM
Subject: Access VNC Server via DNAT
Quoted 5 lines
Quoted 3 lines
Hey,
I have a vnc server that is on my local lan at home that I'd like to be
able
Quoted 1 line
to access from the internet via my internet gateway linux box. I've
read
Quoted 4 lines
a
Quoted 3 lines
little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s
Quoted 10 lines
192.168.0.2 -j
Quoted 1 line
DNAT --to 192.168.0.25:5904
If your internet interface is eth0, you need to do
/sbin/iptables-t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -j DNAT --to-destination 192.168.0.25Please note the above rule will allow you to connect only from internet.
Quoted 1 line
But it says it can't connect to the server. At the moment I'm just
trying
Quoted 2 lines
to
Quoted 1 line
get the port forwarding to work on my local lan, but it doesn't seem to
be
Quoted 1 line
Quoted 1 line
working. I've read of people haveing this working using a somewhat
similar
Quoted 14 lines
Quoted 9 lines
iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a
Does anyone know why this isn't working?
Thanks
Joel
Venkatesh K
Other than connection tracking, if you are using stateful, there are not any special modules needed. I will also add, allowing VNC to penetrate the firewall is not the best of ideas, but very possible to do it securely if you are smart and crafty about it. Here are a couple of thoughts which should help you. First, confirm what port your VNC server is Listening on. The VNC port range is: VNC_PORTS="5900:5910". So, take a look at this.
Having said that, it will also take a minimum of two rules to penetrate the firewall. 1) DNAT correct listening port through to the correct server as you have done with:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 59xx -s 192.168.0.2 -j DNAT --to 192.168.0.25:59xx
That's only half of it. You must then accept the packet once it is has been DNATTED, such as:
$IPT -t filter -A FORWARD -i $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j LOG --log-prefix "ACCEPT INBOUND VNC: " $IPT -t filter -A FORWARD -i $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j ACCEPT
$IPT -t filter -A FORWARD -o $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j LOG --log-prefix "ACCEPT OUTBOUND VNC: " $IPT -t filter -A FORWARD -o $FW_INET_IFACE -p tcp --destination-port $VNC_PORTS -m state --state NEW -j ACCEPT
Additionally, if you are using connection tracking, you must ACCEPT as ESTABLISHED and RELATED as well. Hope this helps.
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Joel Pearson
Sent: Saturday, September 20, 2003 6:57 AM
To: [email protected]
Subject: Access VNC Server via DNAT
Hey,
I have a vnc server that is on my local lan at home that I'd like to be able to access from the internet via my internet gateway linux box. I've read a little bit about it but I can't get my gateway to forward to ports, I've tried this:
iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 5904 -s 192.168.0.2 -j DNAT --to 192.168.0.25:5904
But it says it can't connect to the server. At the moment I'm just trying to get the port forwarding to work on my local lan, but it doesn't seem to be working. I've read of people haveing this working using a somewhat similar iptables command, is there some module I'm supposed to load to make this happen? My server is running RedHat 8 with iptables v1.2.6a
Does anyone know why this isn't working?
Thanks
Joel