[2.4.25] scsi29160 card-aic7xxx, HP Ultrium 230 tape read/write failure
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 28 lines · Jin Suh
Hello,
I recently upgraded my kernel to 2.4.25. I have a strange error using 2.4.25 with Ultrium 230 tape drive. I wrote 4gb data unto the tape and read back to verify md5sum value. It died when it read around 1.3gb data from tape saying following:
(scsi0:A:3:0): parity error detected in Data-in phase. SEQADDR(0x84) SCSIRATE(0x98)
(scsi0:A:3:0): Unexpected busfree in Message-out phase SEQADDR ==0x16b
st0: Error 70000 (sugg. bt0x0, driver bt0x0, host bt0x7).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
........When I tried to read it again using:
dd if=/dev/st0 bs=1024 conv=noerror,sync | md5sum
Quoted 8 lines
I got the following:
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
dd: opening '/dev/st0': Input/Output errorI tested the same thing unto the HP Exabyte and HP SuperStore DAT24. Both worked without problems. But it happened on the HP Ultrium 230 tape drive. Everything used to work fine with 2.4.20 kernel before. Is there any patch for 2.4.25? Do you have any idea?
Hi Jin,
CCing linux-scsi to get more input.
I dont have much clues unfortunately -- reading the SCSI error messages it looks like a parity error.
Can you try 2.4.20 again? Find out where this problem started.
It might be a physical drive problem too which was not failing when you ran 2.4.20.
It appears to be my mistake. At first, I doubt my terminator but I had it on the back of the drive. I fixed it again and switched the scsi cable. It worked OK. Sorry for the interruptions.
Now, I have another problem. I am still using the 2.4.25 kernel with HP Ultrium 230 scsi tape drive. Could you take a look at the following:
st0: Error with sense data: Current st09:00: sns = 70 5
ASC=53 ASCQ= 2
Raw sense data:0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0e 0x00 0x00 0x00 0x00 0x53 0x02 0x00 0x00 0x1c 0x01 0x00 0x00 0x00 0x00
scsi0: Someone reset channel A
I didn't touch any cable or drive. I got this message. I tested my tape drive and it worked fine. Do you have any idea what is going on?
Thanks,
Jin
Quoted 49 lines · --- Marcelo Tosatti
Quoted 3 lines · Jin Suh
Hello,
I recently upgraded my kernel to 2.4.25. I have a strange error using
2.4.25
Quoted 1 line
with Ultrium 230 tape drive. I wrote 4gb data unto the tape and read back
to
Quoted 1 line
verify md5sum value. It died when it read around 1.3gb data from tape
saying
Quoted 23 lines
following:
(scsi0:A:3:0): parity error detected in Data-in phase. SEQADDR(0x84) SCSIRATE(0x98)
(scsi0:A:3:0): Unexpected busfree in Message-out phase SEQADDR ==0x16b
st0: Error 70000 (sugg. bt0x0, driver bt0x0, host bt0x7).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
........When I tried to read it again using:
dd if=/dev/st0 bs=1024 conv=noerror,sync | md5sumQuoted 7 lines
I got the following:
st0: Error 10000 (sugg. bt0x0, driver bt0x0, host bt0x1).
dd: opening '/dev/st0': Input/Output errorI tested the same thing unto the HP Exabyte and HP SuperStore DAT24. Both worked without problems. But it happened on the HP Ultrium 230 tape drive. Everything used to work fine with 2.4.20 kernel before. Is there any patch
for
Quoted 1 line
2.4.25? Do you have any idea?
Hi Jin,
CCing linux-scsi to get more input.
Quoted 7 lines
I dont have much clues unfortunately -- reading the SCSI error messages it looks like a parity error.
Can you try 2.4.20 again? Find out where this problem started.
It might be a physical drive problem too which was not failing when you ran 2.4.20.
__________________________________
Do you Yahoo!?
Yahoo! Mail SpamGuard - Read only the mail you want.
http://antispam.yahoo.com/tools