dt-bindings: convert ata/cortina,gemini-sata-bridge to yaml
Subsystems (2)
PATCH v2 1/1 dt-bindings: convert ata/cortina,gemini-sata-bridge to yaml
This patch converts ata/cortina,gemini-sata-bridge binding to yaml
Reviewed-by Linus Walleij <[email protected]>
Acked-by Damien Le Moal <[email protected]>
Signed-off-by Corentin Labbe <[email protected]>
---
Change since v1:
- fixed cosmetic nits reported by Damien Le Moal
.../ata/cortina,gemini-sata-bridge.txt | 55 ----------- .../ata/cortina,gemini-sata-bridge.yaml | 99 +++++++++++++++++++ 2 files changed, 99 insertions(+), 55 deletions(-) delete mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt create mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt deleted +0 -55
@@ -1,55 +0,0 @@ -* Cortina Systems Gemini SATA Bridge - -The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that -takes two Faraday Technology FTIDE010 PATA controllers and bridges -them in different configurations to two SATA ports. - -Required properties: -- compatible: should be - "cortina,gemini-sata-bridge" -- reg: registers and size for the block -- resets: phandles to the reset lines for both SATA bridges -- reset-names: must be "sata0", "sata1" -- clocks: phandles to the compulsory peripheral clocks -- clock-names: must be "SATA0_PCLK", "SATA1_PCLK" -- syscon: a phandle to the global Gemini system controller -- cortina,gemini-ata-muxmode: tell the desired multiplexing mode for - the ATA controller and SATA bridges. Values 0..3: - Mode 0: ata0 master <-> sata0 - ata1 master <-> sata1 - ata0 slave interface brought out on IDE pads - Mode 1: ata0 master <-> sata0 - ata1 master <-> sata1 - ata1 slave interface brought out on IDE pads - Mode 2: ata1 master <-> sata1 - ata1 slave <-> sata0 - ata0 master and slave interfaces brought out - on IDE pads - Mode 3: ata0 master <-> sata0 - ata0 slave <-> sata1 - ata1 master and slave interfaces brought out - on IDE pads - -Optional boolean properties: -- cortina,gemini-enable-ide-pins: enables the PATA to IDE connection. - The muxmode setting decides whether ATA0 or ATA1 is brought out, - and whether master, slave or both interfaces get brought out. -- cortina,gemini-enable-sata-bridge: enables the PATA to SATA bridge - inside the Gemnini SoC. The Muxmode decides what PATA blocks will - be muxed out and how. - -Example: - -sata: sata@46000000 { - compatible = "cortina,gemini-sata-bridge"; - reg = <0x46000000 0x100>; - resets = <&rcon 26>, <&rcon 27>; - reset-names = "sata0", "sata1"; - clocks = <&gcc GEMINI_CLK_GATE_SATA0>, - <&gcc GEMINI_CLK_GATE_SATA1>; - clock-names = "SATA0_PCLK", "SATA1_PCLK"; - syscon = <&syscon>; - cortina,gemini-ata-muxmode = <3>; - cortina,gemini-enable-ide-pins; - cortina,gemini-enable-sata-bridge; -};
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +99 -0
99 lines not on this page · raw message
Signature · 1 line
2.34.1
Rob Herring
maintainerQuoted 91 lines · Corentin Labbe
This patch converts ata/cortina,gemini-sata-bridge binding to yaml
Reviewed-by Linus Walleij <[email protected]>Acked-by Damien Le Moal <[email protected]>Signed-off-by Corentin Labbe <[email protected]>---
Change since v1:
- fixed cosmetic nits reported by Damien Le Moal.../ata/cortina,gemini-sata-bridge.txt | 55 ----------- .../ata/cortina,gemini-sata-bridge.yaml | 99 +++++++++++++++++++ 2 files changed, 99 insertions(+), 55 deletions(-) delete mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt create mode 100644 Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yamlDocumentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.txt deleted +0
-55@@ -1,55 +0,0 @@ -* Cortina Systems Gemini SATA Bridge - -The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that -takes two Faraday Technology FTIDE010 PATA controllers and bridges -them in different configurations to two SATA ports. - -Required properties: -- compatible: should be - "cortina,gemini-sata-bridge" -- reg: registers and size for the block -- resets: phandles to the reset lines for both SATA bridges -- reset-names: must be "sata0", "sata1" -- clocks: phandles to the compulsory peripheral clocks -- clock-names: must be "SATA0_PCLK", "SATA1_PCLK" -- syscon: a phandle to the global Gemini system controller -- cortina,gemini-ata-muxmode: tell the desired multiplexing mode for - the ATA controller and SATA bridges. Values 0..3: - Mode 0: ata0 master <-> sata0 - ata1 master <-> sata1 - ata0 slave interface brought out on IDE pads - Mode 1: ata0 master <-> sata0 - ata1 master <-> sata1 - ata1 slave interface brought out on IDE pads - Mode 2: ata1 master <-> sata1 - ata1 slave <-> sata0 - ata0 master and slave interfaces brought out - on IDE pads - Mode 3: ata0 master <-> sata0 - ata0 slave <-> sata1 - ata1 master and slave interfaces brought out - on IDE pads - -Optional boolean properties: -- cortina,gemini-enable-ide-pins: enables the PATA to IDE connection. - The muxmode setting decides whether ATA0 or ATA1 is brought out, - and whether master, slave or both interfaces get brought out. -- cortina,gemini-enable-sata-bridge: enables the PATA to SATA bridge - inside the Gemnini SoC. The Muxmode decides what PATA blocks will - be muxed out and how. - -Example: - -sata: sata@46000000 { - compatible = "cortina,gemini-sata-bridge"; - reg = <0x46000000 0x100>; - resets = <&rcon 26>, <&rcon 27>; - reset-names = "sata0", "sata1"; - clocks = <&gcc GEMINI_CLK_GATE_SATA0>, - <&gcc GEMINI_CLK_GATE_SATA1>; - clock-names = "SATA0_PCLK", "SATA1_PCLK"; - syscon = <&syscon>; - cortina,gemini-ata-muxmode = <3>; - cortina,gemini-enable-ide-pins; - cortina,gemini-enable-sata-bridge; -};Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +9
-0@@ -0,0 +1,99 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/cortina,gemini-sata-bridge.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cortina Systems Gemini SATA Bridge + +maintainers:
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml line 19
Quoted 10 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +10
-0+ - Linus Walleij <[email protected]> + +description: | + The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that + takes two Faraday Technology FTIDE010 PATA controllers and bridges + them in different configurations to two SATA ports. + +properties: + compatible: + const: "cortina,gemini-sata-bridge"
Don't need quotes.
blank line between DT properties.
Quoted 37 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +37
-0+ reg: + minItems: 1 + resets: + minItems: 2 + description: phandles to the reset lines for both SATA bridges + reset-names: + items: + - const: "sata0" + - const: "sata1" + clocks: + minItems: 2 + description: phandles to the compulsory peripheral clocks + clock-names: + items: + - const: "SATA0_PCLK" + - const: "SATA1_PCLK" + syscon: + minItems: 1 + $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to the global Gemini system controller + cortina,gemini-ata-muxmode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: + - 0 + - 1 + - 2 + - 3 + description: | + Tell the desired multiplexing mode for the ATA controller and SATA bridges. Values 0..3: + Mode 0: ata0 master <-> sata0 + ata1 master <-> sata1 + ata0 slave interface brought out on IDE pads + Mode 1: ata0 master <-> sata0 + ata1 master <-> sata1 + ata1 slave interface brought out on IDE pads + Mode 2: ata1 master <-> sata1 + ata1 slave <-> sata0
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml line 66
Quoted 10 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +10
-0+ ata0 master and slave interfaces brought out on IDE pads + Mode 3: ata0 master <-> sata0 + ata0 slave <-> sata1 + ata1 master and slave interfaces brought out on IDE pads + + cortina,gemini-enable-ide-pins: + type: boolean + description: Enables the PATA to IDE connection. + The muxmode setting decides whether ATA0 or ATA1 is brought out, + and whether master, slave or both interfaces get brought out.
Indent 2 spaces more than 'description'
Quoted 11 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +11
-0+ cortina,gemini-enable-sata-bridge: + type: boolean + description: Enables the PATA to SATA bridge inside the Gemnini SoC. + The Muxmode decides what PATA blocks will be muxed out and how. + +required: + - clocks + - clock-names + - cortina,gemini-ata-muxmode + - resets + - reset-names
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml line 87
Quoted 10 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +10
-0+ - compatible + - reg + - syscon + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/cortina,gemini-clock.h> + sata: sata@46000000 {
Drop unused labels.
Quoted 16 lines
Documentation/devicetree/bindings/ata/cortina,gemini-sata-bridge.yaml new file +12
-0+ compatible = "cortina,gemini-sata-bridge"; + reg = <0x46000000 0x100>; + resets = <&rcon 26>, <&rcon 27>; + reset-names = "sata0", "sata1"; + clocks = <&gcc GEMINI_CLK_GATE_SATA0>, + <&gcc GEMINI_CLK_GATE_SATA1>; + clock-names = "SATA0_PCLK", "SATA1_PCLK"; + syscon = <&syscon>; + cortina,gemini-ata-muxmode = <3>; + cortina,gemini-enable-ide-pins; + cortina,gemini-enable-sata-bridge; + };Signature · 1 line
2.34.1