Skip to contentSkip to conversation

Fixes for DP8393X SONIC device emulation

PATCH Applied Finn Thain 5 participants 27 messages Jan 29, 2020 – Feb 20, 2020

lore
Share & tools
lore

Finn Thain

author
#0 lore raw

v4 cover Fixes for DP8393X SONIC device emulation

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely trigger an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---
Changed since v1:
- Minor revisions as described beneath commit logs.
- Dropped patches 4/10 and 7/10.
- Added 5 new patches.

Changed since v2:
- Minor revisions as described beneath commit logs.
- Dropped patch 13/13.
- Added 2 new patches.

Changed since v3:
- Replaced patch 13/14 with patch suggested by Philippe Mathieu-Daudé.

Finn Thain (14):
dp8393x: Mask EOL bit from descriptor addresses
dp8393x: Always use 32-bit accesses
dp8393x: Clean up endianness hacks
dp8393x: Have dp8393x_receive() return the packet size
dp8393x: Update LLFA and CRDA registers from rx descriptor
dp8393x: Clear RRRA command register bit only when appropriate
dp8393x: Implement packet size limit and RBAE interrupt
dp8393x: Don't clobber packet checksum
dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
dp8393x: Pad frames to word or long word boundary
dp8393x: Clear descriptor in_use field to release packet
dp8393x: Always update RRA pointers and sequence numbers
dp8393x: Don't reset Silicon Revision register
dp8393x: Don't stop reception upon RBE interrupt assertion

 hw/net/dp8393x.c | 202 +++++++++++++++++++++++++++++++----------------
 1 file changed, 134 insertions(+), 68 deletions(-)
Signature · 1 line
2.24.1
author
#1 lore raw

PATCH v4 1/14 dp8393x: Mask EOL bit from descriptor addresses

The Least Significant bit of a descriptor address register is used as an EOL flag. It has to be masked when the register value is to be used as an actual address for copying memory around. But when the registers are to be updated the EOL bit should not be masked.

---
Changed since v1:
- Added macros to name constants as requested by Philippe Mathieu-Daudé.

---
 hw/net/dp8393x.c | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)
hw/net/dp8393x.c +12 -7
index cdc2631c0c..14901c1445 100644
@@ -145,6 +145,9 @@ do { printf("sonic ERROR: %s: " fmt, __func__ , ## __VA_ARGS__); } while (0)
 #define SONIC_ISR_PINT   0x0800
 #define SONIC_ISR_LCD    0x1000
 
+#define SONIC_DESC_EOL   0x0001
+#define SONIC_DESC_ADDR  0xFFFE
+
 #define TYPE_DP8393X "dp8393x"
 #define DP8393X(obj) OBJECT_CHECK(dp8393xState, (obj), TYPE_DP8393X)
 
@@ -197,7 +200,8 @@ static uint32_t dp8393x_crba(dp8393xState *s)
 
 static uint32_t dp8393x_crda(dp8393xState *s)
 {
-    return (s->regs[SONIC_URDA] << 16) | s->regs[SONIC_CRDA];
+    return (s->regs[SONIC_URDA] << 16) |
+           (s->regs[SONIC_CRDA] & SONIC_DESC_ADDR);
 }
 
 static uint32_t dp8393x_rbwc(dp8393xState *s)
@@ -217,7 +221,8 @@ static uint32_t dp8393x_tsa(dp8393xState *s)
 
 static uint32_t dp8393x_ttda(dp8393xState *s)
 {
-    return (s->regs[SONIC_UTDA] << 16) | s->regs[SONIC_TTDA];
+    return (s->regs[SONIC_UTDA] << 16) |
+           (s->regs[SONIC_TTDA] & SONIC_DESC_ADDR);
 }
 
 static uint32_t dp8393x_wt(dp8393xState *s)
@@ -506,8 +511,8 @@ static void dp8393x_do_transmit_packets(dp8393xState *s)
                              sizeof(uint16_t) *
                              (4 + 3 * s->regs[SONIC_TFC]) * width,
                 MEMTXATTRS_UNSPECIFIED, (uint8_t *)s->data, size, 0);
-            s->regs[SONIC_CTDA] = dp8393x_get(s, width, 0) & ~0x1;
-            if (dp8393x_get(s, width, 0) & 0x1) {
+            s->regs[SONIC_CTDA] = dp8393x_get(s, width, 0);
+            if (s->regs[SONIC_CTDA] & SONIC_DESC_EOL) {
                 /* EOL detected */
                 break;
             }
@@ -763,13 +768,13 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     /* XXX: Check byte ordering */
 
     /* Check for EOL */
-    if (s->regs[SONIC_LLFA] & 0x1) {
+    if (s->regs[SONIC_LLFA] & SONIC_DESC_EOL) {
         /* Are we still in resource exhaustion? */
         size = sizeof(uint16_t) * 1 * width;
         address = dp8393x_crda(s) + sizeof(uint16_t) * 5 * width;
         address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
                          (uint8_t *)s->data, size, 0);
-        if (dp8393x_get(s, width, 0) & 0x1) {
+        if (dp8393x_get(s, width, 0) & SONIC_DESC_EOL) {
             /* Still EOL ; stop reception */
             return -1;
         } else {
@@ -827,7 +832,7 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     address_space_rw(&s->as, dp8393x_crda(s) + sizeof(uint16_t) * 5 * width,
         MEMTXATTRS_UNSPECIFIED, (uint8_t *)s->data, size, 0);
     s->regs[SONIC_LLFA] = dp8393x_get(s, width, 0);
-    if (s->regs[SONIC_LLFA] & 0x1) {
+    if (s->regs[SONIC_LLFA] & SONIC_DESC_EOL) {
         /* EOL detected */
         s->regs[SONIC_ISR] |= SONIC_ISR_RDE;
     } else {
Signature · 1 line
2.24.1
author
#2 lore raw

PATCH v4 2/14 dp8393x: Always use 32-bit accesses

In reply to Finn Thain

The DP83932 and DP83934 have 32 data lines. The datasheet says,

Data Bus: These bidirectional lines are used to transfer data on the system bus. When the SONIC is a bus master, 16-bit data is transferred on D15-D0 and 32-bit data is transferred on D31-D0. When the SONIC is accessed as a slave, register data is driven onto lines D15-D0. D31-D16 are held TRI-STATE if SONIC is in 16-bit mode. If SONIC is in 32-bit mode, they are driven, but invalid.

Always use 32-bit accesses both as bus master and bus slave.

Force the MSW to zero in bus master mode.

This gets the Linux 'jazzsonic' driver working, and avoids the need for prior hacks to make the NetBSD 'sn' driver work.

---
 hw/net/dp8393x.c | 47 +++++++++++++++++++++++++++++------------------
 1 file changed, 29 insertions(+), 18 deletions(-)
hw/net/dp8393x.c +29 -18
index 14901c1445..b2fd44bc2f 100644
@@ -246,9 +246,19 @@ static void dp8393x_put(dp8393xState *s, int width, int offset,
                         uint16_t val)
 {
     if (s->big_endian) {
-        s->data[offset * width + width - 1] = cpu_to_be16(val);
+        if (width == 2) {
+            s->data[offset * 2] = 0;
+            s->data[offset * 2 + 1] = cpu_to_be16(val);
+        } else {
+            s->data[offset] = cpu_to_be16(val);
+        }
     } else {
-        s->data[offset * width] = cpu_to_le16(val);
+        if (width == 2) {
+            s->data[offset * 2] = cpu_to_le16(val);
+            s->data[offset * 2 + 1] = 0;
+        } else {
+            s->data[offset] = cpu_to_le16(val);
+        }
     }
 }
 
@@ -588,7 +598,7 @@ static uint64_t dp8393x_read(void *opaque, hwaddr addr, unsigned int size)
 
     DPRINTF("read 0x%04x from reg %s\n", val, reg_names[reg]);
 
-    return val;
+    return s->big_endian ? val << 16 : val;
 }
 
 static void dp8393x_write(void *opaque, hwaddr addr, uint64_t data,
@@ -596,13 +606,14 @@ static void dp8393x_write(void *opaque, hwaddr addr, uint64_t data,
 {
     dp8393xState *s = opaque;
     int reg = addr >> s->it_shift;
+    uint32_t val = s->big_endian ? data >> 16 : data;
 
-    DPRINTF("write 0x%04x to reg %s\n", (uint16_t)data, reg_names[reg]);
+    DPRINTF("write 0x%04x to reg %s\n", (uint16_t)val, reg_names[reg]);
 
     switch (reg) {
         /* Command register */
         case SONIC_CR:
-            dp8393x_do_command(s, data);
+            dp8393x_do_command(s, val);
             break;
         /* Prevent write to read-only registers */
         case SONIC_CAP2:
@@ -615,36 +626,36 @@ static void dp8393x_write(void *opaque, hwaddr addr, uint64_t data,
         /* Accept write to some registers only when in reset mode */
         case SONIC_DCR:
             if (s->regs[SONIC_CR] & SONIC_CR_RST) {
-                s->regs[reg] = data & 0xbfff;
+                s->regs[reg] = val & 0xbfff;
             } else {
                 DPRINTF("writing to DCR invalid\n");
             }
             break;
         case SONIC_DCR2:
             if (s->regs[SONIC_CR] & SONIC_CR_RST) {
-                s->regs[reg] = data & 0xf017;
+                s->regs[reg] = val & 0xf017;
             } else {
                 DPRINTF("writing to DCR2 invalid\n");
             }
             break;
         /* 12 lower bytes are Read Only */
         case SONIC_TCR:
-            s->regs[reg] = data & 0xf000;
+            s->regs[reg] = val & 0xf000;
             break;
         /* 9 lower bytes are Read Only */
         case SONIC_RCR:
-            s->regs[reg] = data & 0xffe0;
+            s->regs[reg] = val & 0xffe0;
             break;
         /* Ignore most significant bit */
         case SONIC_IMR:
-            s->regs[reg] = data & 0x7fff;
+            s->regs[reg] = val & 0x7fff;
             dp8393x_update_irq(s);
             break;
         /* Clear bits by writing 1 to them */
         case SONIC_ISR:
-            data &= s->regs[reg];
-            s->regs[reg] &= ~data;
-            if (data & SONIC_ISR_RBE) {
+            val &= s->regs[reg];
+            s->regs[reg] &= ~val;
+            if (val & SONIC_ISR_RBE) {
                 dp8393x_do_read_rra(s);
             }
             dp8393x_update_irq(s);
@@ -657,17 +668,17 @@ static void dp8393x_write(void *opaque, hwaddr addr, uint64_t data,
         case SONIC_REA:
         case SONIC_RRP:
         case SONIC_RWP:
-            s->regs[reg] = data & 0xfffe;
+            s->regs[reg] = val & 0xfffe;
             break;
         /* Invert written value for some registers */
         case SONIC_CRCT:
         case SONIC_FAET:
         case SONIC_MPT:
-            s->regs[reg] = data ^ 0xffff;
+            s->regs[reg] = val ^ 0xffff;
             break;
         /* All other registers have no special contrainst */
         default:
-            s->regs[reg] = data;
+            s->regs[reg] = val;
     }
 
     if (reg == SONIC_WT0 || reg == SONIC_WT1) {
@@ -678,8 +689,8 @@ static void dp8393x_write(void *opaque, hwaddr addr, uint64_t data,
 static const MemoryRegionOps dp8393x_ops = {
     .read = dp8393x_read,
     .write = dp8393x_write,
-    .impl.min_access_size = 2,
-    .impl.max_access_size = 2,
+    .impl.min_access_size = 4,
+    .impl.max_access_size = 4,
     .endianness = DEVICE_NATIVE_ENDIAN,
 };
 
Signature · 1 line
2.24.1
author
#3 lore raw

PATCH v4 3/14 dp8393x: Clean up endianness hacks

In reply to Finn Thain

According to the datasheet, section 3.4.4, "in 32-bit mode ... the SONIC always writes long words".

Therefore, use the same technique for the 'in_use' field that is used everywhere else, and write the full long word.

---
Changed since v1:
- Use existing 'address' variable rather than declare a new one.

Laurent tells me that a similar clean-up has been tried before. He referred me to commit c744cf7879 ("dp8393x: fix dp8393x_receive()") and commit 409b52bfe1 ("net/dp8393x: correctly reset in_use field"). I believe the underlying issue has been fixed by the preceding patch, as this no longer breaks NetBSD 5.1.

---
 hw/net/dp8393x.c | 17 ++++++-----------
 1 file changed, 6 insertions(+), 11 deletions(-)
hw/net/dp8393x.c +6 -11
index b2fd44bc2f..2d2ace2549 100644
@@ -776,8 +776,6 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
         return -1;
     }
 
-    /* XXX: Check byte ordering */
-
     /* Check for EOL */
     if (s->regs[SONIC_LLFA] & SONIC_DESC_EOL) {
         /* Are we still in resource exhaustion? */
@@ -847,15 +845,12 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
         /* EOL detected */
         s->regs[SONIC_ISR] |= SONIC_ISR_RDE;
     } else {
-        /* Clear in_use, but it is always 16bit wide */
-        int offset = dp8393x_crda(s) + sizeof(uint16_t) * 6 * width;
-        if (s->big_endian && width == 2) {
-            /* we need to adjust the offset of the 16bit field */
-            offset += sizeof(uint16_t);
-        }
-        s->data[0] = 0;
-        address_space_rw(&s->as, offset, MEMTXATTRS_UNSPECIFIED,
-                         (uint8_t *)s->data, sizeof(uint16_t), 1);
+        /* Clear in_use */
+        size = sizeof(uint16_t) * width;
+        address = dp8393x_crda(s) + sizeof(uint16_t) * 6 * width;
+        dp8393x_put(s, width, 0, 0);
+        address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
+                         (uint8_t *)s->data, size, 1);
         s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
         s->regs[SONIC_ISR] |= SONIC_ISR_PKTRX;
         s->regs[SONIC_RSC] = (s->regs[SONIC_RSC] & 0xff00) | (((s->regs[SONIC_RSC] & 0x00ff) + 1) & 0x00ff);
Signature · 1 line
2.24.1
author
#4 lore raw

PATCH v4 4/14 dp8393x: Have dp8393x_receive() return the packet size

In reply to Finn Thain

This function re-uses its 'size' argument as a scratch variable. Instead, declare a local 'size' variable for that purpose so that the function result doesn't get messed up.

---
 hw/net/dp8393x.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
hw/net/dp8393x.c +5 -4
index 2d2ace2549..ece72cbf42 100644
@@ -757,20 +757,21 @@ static int dp8393x_receive_filter(dp8393xState *s, const uint8_t * buf,
 }
 
 static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
-                               size_t size)
+                               size_t pkt_size)
 {
     dp8393xState *s = qemu_get_nic_opaque(nc);
     int packet_type;
     uint32_t available, address;
-    int width, rx_len = size;
+    int width, rx_len = pkt_size;
     uint32_t checksum;
+    int size;
 
     width = (s->regs[SONIC_DCR] & SONIC_DCR_DW) ? 2 : 1;
 
     s->regs[SONIC_RCR] &= ~(SONIC_RCR_PRX | SONIC_RCR_LBK | SONIC_RCR_FAER |
         SONIC_RCR_CRCR | SONIC_RCR_LPKT | SONIC_RCR_BC | SONIC_RCR_MC);
 
-    packet_type = dp8393x_receive_filter(s, buf, size);
+    packet_type = dp8393x_receive_filter(s, buf, pkt_size);
     if (packet_type < 0) {
         DPRINTF("packet not for netcard\n");
         return -1;
@@ -864,7 +865,7 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     /* Done */
     dp8393x_update_irq(s);
 
-    return size;
+    return pkt_size;
 }
 
 static void dp8393x_reset(DeviceState *dev)
Signature · 1 line
2.24.1
author
#5 lore raw

PATCH v4 5/14 dp8393x: Update LLFA and CRDA registers from rx descriptor

In reply to Finn Thain

Follow the algorithm given in the National Semiconductor DP83932C datasheet in section 3.4.7:

At the next reception, the SONIC re-reads the last RXpkt.link field, and updates its CRDA register to point to the next descriptor.

The chip is designed to allow the host to provide a new list of descriptors in this way.

---
Changed since v1:
- Update CRDA register from LLFA register after EOL is cleared.

---
 hw/net/dp8393x.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
hw/net/dp8393x.c +7 -4
index ece72cbf42..249be403af 100644
@@ -784,12 +784,13 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
         address = dp8393x_crda(s) + sizeof(uint16_t) * 5 * width;
         address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
                          (uint8_t *)s->data, size, 0);
-        if (dp8393x_get(s, width, 0) & SONIC_DESC_EOL) {
+        s->regs[SONIC_LLFA] = dp8393x_get(s, width, 0);
+        if (s->regs[SONIC_LLFA] & SONIC_DESC_EOL) {
             /* Still EOL ; stop reception */
             return -1;
-        } else {
-            s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
         }
+        /* Link has been updated by host */
+        s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
     }
 
     /* Save current position */
@@ -837,7 +838,7 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     address_space_rw(&s->as, dp8393x_crda(s),
         MEMTXATTRS_UNSPECIFIED, (uint8_t *)s->data, size, 1);
 
-    /* Move to next descriptor */
+    /* Check link field */
     size = sizeof(uint16_t) * width;
     address_space_rw(&s->as, dp8393x_crda(s) + sizeof(uint16_t) * 5 * width,
         MEMTXATTRS_UNSPECIFIED, (uint8_t *)s->data, size, 0);
@@ -852,6 +853,8 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
         dp8393x_put(s, width, 0, 0);
         address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
                          (uint8_t *)s->data, size, 1);
+
+        /* Move to next descriptor */
         s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
         s->regs[SONIC_ISR] |= SONIC_ISR_PKTRX;
         s->regs[SONIC_RSC] = (s->regs[SONIC_RSC] & 0xff00) | (((s->regs[SONIC_RSC] & 0x00ff) + 1) & 0x00ff);
Signature · 1 line
2.24.1
Reviewed-by on v4 5/14
#6 lore raw

Re: [PATCH v4 05/14] dp8393x: Update LLFA and CRDA registers from rx descriptor

Quoted 26 lines · Finn Thain

Follow the algorithm given in the National Semiconductor DP83932C datasheet in section 3.4.7:

At the next reception, the SONIC re-reads the last RXpkt.link field, and updates its CRDA register to point to the next descriptor.

The chip is designed to allow the host to provide a new list of descriptors in this way.

---
Changed since v1:
- Update CRDA register from LLFA register after EOL is cleared.

---
  hw/net/dp8393x.c | 11 +++++++----
  1 file changed, 7 insertions(+), 4 deletions(-)
hw/net/dp8393x.c +0 -0
index ece72cbf42..249be403af 100644
@@ -784,12 +784,13 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
          address = dp8393x_crda(s) + sizeof(uint16_t) * 5 * width;
          address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
                           (uint8_t *)s->data, size, 0);

hw/net/dp8393x.c static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf, · line 793

Quoted 10 lines
hw/net/dp8393x.c +4 -3
-        if (dp8393x_get(s, width, 0) & SONIC_DESC_EOL) {
+        s->regs[SONIC_LLFA] = dp8393x_get(s, width, 0);
+        if (s->regs[SONIC_LLFA] & SONIC_DESC_EOL) {
              /* Still EOL ; stop reception */
              return -1;
-        } else {
-            s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
          }
+        /* Link has been updated by host */
+        s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
Quoted 22 lines
hw/net/dp8393x.c +3 -1
      }
 
      /* Save current position */
@@ -837,7 +838,7 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
      address_space_rw(&s->as, dp8393x_crda(s),
          MEMTXATTRS_UNSPECIFIED, (uint8_t *)s->data, size, 1);
 
-    /* Move to next descriptor */
+    /* Check link field */
      size = sizeof(uint16_t) * width;
      address_space_rw(&s->as, dp8393x_crda(s) + sizeof(uint16_t) * 5 * width,
          MEMTXATTRS_UNSPECIFIED, (uint8_t *)s->data, size, 0);
@@ -852,6 +853,8 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
          dp8393x_put(s, width, 0, 0);
          address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
                           (uint8_t *)s->data, size, 1);
+
+        /* Move to next descriptor */
          s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
          s->regs[SONIC_ISR] |= SONIC_ISR_PKTRX;
          s->regs[SONIC_RSC] = (s->regs[SONIC_RSC] & 0xff00) | (((s->regs[SONIC_RSC] & 0x00ff) + 1) & 0x00ff);
author
#7 lore raw

PATCH v4 6/14 dp8393x: Clear RRRA command register bit only when appropriate

In reply to Finn Thain

It doesn't make sense to clear the command register bit unless the command was actually issued.

---
 hw/net/dp8393x.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
hw/net/dp8393x.c +3 -4
index 249be403af..2e976781e2 100644
@@ -352,9 +352,6 @@ static void dp8393x_do_read_rra(dp8393xState *s)
         s->regs[SONIC_ISR] |= SONIC_ISR_RBE;
         dp8393x_update_irq(s);
     }
-
-    /* Done */
-    s->regs[SONIC_CR] &= ~SONIC_CR_RRRA;
 }
 
 static void dp8393x_do_software_reset(dp8393xState *s)
@@ -563,8 +560,10 @@ static void dp8393x_do_command(dp8393xState *s, uint16_t command)
         dp8393x_do_start_timer(s);
     if (command & SONIC_CR_RST)
         dp8393x_do_software_reset(s);
-    if (command & SONIC_CR_RRRA)
+    if (command & SONIC_CR_RRRA) {
         dp8393x_do_read_rra(s);
+        s->regs[SONIC_CR] &= ~SONIC_CR_RRRA;
+    }
     if (command & SONIC_CR_LCAM)
         dp8393x_do_load_cam(s);
 }
Signature · 1 line
2.24.1
author
#8 lore raw

PATCH v4 7/14 dp8393x: Implement packet size limit and RBAE interrupt

In reply to Finn Thain

Add a bounds check to prevent a large packet from causing a buffer overflow. This is defensive programming -- I haven't actually tried sending an oversized packet or a jumbo ethernet frame.

The SONIC handles packets that are too big for the buffer by raising the RBAE interrupt and dropping them. Linux uses that interrupt to count dropped packets.

---
Changed since v1:
- Perform length check after Recieve Control Register initialization.

---
 hw/net/dp8393x.c | 9 +++++++++
 1 file changed, 9 insertions(+)
hw/net/dp8393x.c +9 -0
index 2e976781e2..0309365fda 100644
@@ -137,6 +137,7 @@ do { printf("sonic ERROR: %s: " fmt, __func__ , ## __VA_ARGS__); } while (0)
 #define SONIC_TCR_CRCI   0x2000
 #define SONIC_TCR_PINT   0x8000
 
+#define SONIC_ISR_RBAE   0x0010
 #define SONIC_ISR_RBE    0x0020
 #define SONIC_ISR_RDE    0x0040
 #define SONIC_ISR_TC     0x0080
@@ -770,6 +771,14 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     s->regs[SONIC_RCR] &= ~(SONIC_RCR_PRX | SONIC_RCR_LBK | SONIC_RCR_FAER |
         SONIC_RCR_CRCR | SONIC_RCR_LPKT | SONIC_RCR_BC | SONIC_RCR_MC);
 
+    if (pkt_size + 4 > dp8393x_rbwc(s) * 2) {
+        DPRINTF("oversize packet, pkt_size is %d\n", pkt_size);
+        s->regs[SONIC_ISR] |= SONIC_ISR_RBAE;
+        dp8393x_update_irq(s);
+        dp8393x_do_read_rra(s);
+        return pkt_size;
+    }
+
     packet_type = dp8393x_receive_filter(s, buf, pkt_size);
     if (packet_type < 0) {
         DPRINTF("packet not for netcard\n");
Signature · 1 line
2.24.1
author
#9 lore raw

PATCH v4 8/14 dp8393x: Don't clobber packet checksum

In reply to Finn Thain

A received packet consumes pkt_size bytes in the buffer and the frame checksum that's appended to it consumes another 4 bytes. The Receive Buffer Address register takes the former quantity into account but not the latter. So the next packet written to the buffer overwrites the frame checksum. Fix this.

---
 hw/net/dp8393x.c | 1 +
 1 file changed, 1 insertion(+)
hw/net/dp8393x.c +1 -0
index 0309365fda..947ceef37c 100644
@@ -816,6 +816,7 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     address += rx_len;
     address_space_rw(&s->as, address,
         MEMTXATTRS_UNSPECIFIED, (uint8_t *)&checksum, 4, 1);
+    address += 4;
     rx_len += 4;
     s->regs[SONIC_CRBA1] = address >> 16;
     s->regs[SONIC_CRBA0] = address & 0xffff;
Signature · 1 line
2.24.1
author
#10 lore raw

PATCH v4 9/14 dp8393x: Use long-word-aligned RRA pointers in 32-bit mode

In reply to Finn Thain

Section 3.4.1 of the datasheet says,

The alignment of the RRA is confined to either word or long word boundaries, depending upon the data width mode. In 16-bit mode, the RRA must be aligned to a word boundary (A0 is always zero) and in 32-bit mode, the RRA is aligned to a long word boundary (A0 and A1 are always zero).

This constraint has been implemented for 16-bit mode; implement it for 32-bit mode too.

---
 hw/net/dp8393x.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
hw/net/dp8393x.c +6 -2
index 947ceef37c..b052e2c854 100644
@@ -663,12 +663,16 @@ static void dp8393x_write(void *opaque, hwaddr addr, uint64_t data,
                 qemu_flush_queued_packets(qemu_get_queue(s->nic));
             }
             break;
-        /* Ignore least significant bit */
+        /* The guest is required to store aligned pointers here */
         case SONIC_RSA:
         case SONIC_REA:
         case SONIC_RRP:
         case SONIC_RWP:
-            s->regs[reg] = val & 0xfffe;
+            if (s->regs[SONIC_DCR] & SONIC_DCR_DW) {
+                s->regs[reg] = val & 0xfffc;
+            } else {
+                s->regs[reg] = val & 0xfffe;
+            }
             break;
         /* Invert written value for some registers */
         case SONIC_CRCT:
Signature · 1 line
2.24.1
author
#11 lore raw

PATCH v4 10/14 dp8393x: Pad frames to word or long word boundary

In reply to Finn Thain

The existing code has a bug where the Remaining Buffer Word Count (RBWC) is calculated with a truncating division, which gives the wrong result for odd-sized packets.

Section 1.4.1 of the datasheet says,

Once the end of the packet has been reached, the serializer will fill out the last word (16-bit mode) or long word (32-bit mode) if the last byte did not end on a word or long word boundary respectively. The fill byte will be 0FFh.

Implement buffer padding so that buffer limits are correctly enforced.

---
 hw/net/dp8393x.c | 39 ++++++++++++++++++++++++++++-----------
 1 file changed, 28 insertions(+), 11 deletions(-)
hw/net/dp8393x.c +28 -11
index b052e2c854..13513986f0 100644
@@ -766,16 +766,23 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     dp8393xState *s = qemu_get_nic_opaque(nc);
     int packet_type;
     uint32_t available, address;
-    int width, rx_len = pkt_size;
+    int width, rx_len, padded_len;
     uint32_t checksum;
     int size;
 
-    width = (s->regs[SONIC_DCR] & SONIC_DCR_DW) ? 2 : 1;
-
     s->regs[SONIC_RCR] &= ~(SONIC_RCR_PRX | SONIC_RCR_LBK | SONIC_RCR_FAER |
         SONIC_RCR_CRCR | SONIC_RCR_LPKT | SONIC_RCR_BC | SONIC_RCR_MC);
 
-    if (pkt_size + 4 > dp8393x_rbwc(s) * 2) {
+    rx_len = pkt_size + sizeof(checksum);
+    if (s->regs[SONIC_DCR] & SONIC_DCR_DW) {
+        width = 2;
+        padded_len = ((rx_len - 1) | 3) + 1;
+    } else {
+        width = 1;
+        padded_len = ((rx_len - 1) | 1) + 1;
+    }
+
+    if (padded_len > dp8393x_rbwc(s) * 2) {
         DPRINTF("oversize packet, pkt_size is %d\n", pkt_size);
         s->regs[SONIC_ISR] |= SONIC_ISR_RBAE;
         dp8393x_update_irq(s);
@@ -810,22 +817,32 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     s->regs[SONIC_TRBA0] = s->regs[SONIC_CRBA0];
 
     /* Calculate the ethernet checksum */
-    checksum = cpu_to_le32(crc32(0, buf, rx_len));
+    checksum = cpu_to_le32(crc32(0, buf, pkt_size));
 
     /* Put packet into RBA */
     DPRINTF("Receive packet at %08x\n", dp8393x_crba(s));
     address = dp8393x_crba(s);
     address_space_rw(&s->as, address,
-        MEMTXATTRS_UNSPECIFIED, (uint8_t *)buf, rx_len, 1);
-    address += rx_len;
+        MEMTXATTRS_UNSPECIFIED, (uint8_t *)buf, pkt_size, 1);
+    address += pkt_size;
+
+    /* Put frame checksum into RBA */
     address_space_rw(&s->as, address,
-        MEMTXATTRS_UNSPECIFIED, (uint8_t *)&checksum, 4, 1);
-    address += 4;
-    rx_len += 4;
+        MEMTXATTRS_UNSPECIFIED, (uint8_t *)&checksum, sizeof(checksum), 1);
+    address += sizeof(checksum);
+
+    /* Pad short packets to keep pointers aligned */
+    if (rx_len < padded_len) {
+        size = padded_len - rx_len;
+        address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
+            (uint8_t *)"\xFF\xFF\xFF", size, 1);
+        address += size;
+    }
+
     s->regs[SONIC_CRBA1] = address >> 16;
     s->regs[SONIC_CRBA0] = address & 0xffff;
     available = dp8393x_rbwc(s);
-    available -= rx_len / 2;
+    available -= padded_len >> 1;
     s->regs[SONIC_RBWC1] = available >> 16;
     s->regs[SONIC_RBWC0] = available & 0xffff;
 
Signature · 1 line
2.24.1
author
#12 lore raw

PATCH v4 11/14 dp8393x: Clear descriptor in_use field to release packet

In reply to Finn Thain

When the SONIC receives a packet into the last available descriptor, it retains ownership of that descriptor for as long as necessary.

Section 3.4.7 of the datasheet says,

When the system appends more descriptors, the SONIC releases ownership of the descriptor after writing 0000h to the RXpkt.in_use field.

The packet can now be processed by the host, so raise a PKTRX interrupt, just like the normal case.

---
Changed since v2:
- Assert PKTRX interrupt when releasing withheld packet.

---
 hw/net/dp8393x.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
hw/net/dp8393x.c +10 -0
index 13513986f0..99c5dad7c4 100644
@@ -809,7 +809,17 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
             return -1;
         }
         /* Link has been updated by host */
+
+        /* Clear in_use */
+        size = sizeof(uint16_t) * width;
+        address = dp8393x_crda(s) + sizeof(uint16_t) * 6 * width;
+        dp8393x_put(s, width, 0, 0);
+        address_space_rw(&s->as, address, MEMTXATTRS_UNSPECIFIED,
+                         (uint8_t *)s->data, size, 1);
+
+        /* Move to next descriptor */
         s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
+        s->regs[SONIC_ISR] |= SONIC_ISR_PKTRX;
     }
 
     /* Save current position */
Signature · 1 line
2.24.1
author
#13 lore raw

PATCH v4 12/14 dp8393x: Always update RRA pointers and sequence numbers

In reply to Finn Thain

These operations need to take place regardless of whether or not rx descriptors have been used up (that is, EOL flag was observed).

The algorithm is now the same for a packet that was withheld as for a packet that was not.

---
 hw/net/dp8393x.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
hw/net/dp8393x.c +7 -5
index 99c5dad7c4..1b73a8703b 100644
@@ -897,12 +897,14 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
         /* Move to next descriptor */
         s->regs[SONIC_CRDA] = s->regs[SONIC_LLFA];
         s->regs[SONIC_ISR] |= SONIC_ISR_PKTRX;
-        s->regs[SONIC_RSC] = (s->regs[SONIC_RSC] & 0xff00) | (((s->regs[SONIC_RSC] & 0x00ff) + 1) & 0x00ff);
+    }
 
-        if (s->regs[SONIC_RCR] & SONIC_RCR_LPKT) {
-            /* Read next RRA */
-            dp8393x_do_read_rra(s);
-        }
+    s->regs[SONIC_RSC] = (s->regs[SONIC_RSC] & 0xff00) |
+                         ((s->regs[SONIC_RSC] + 1) & 0x00ff);
+
+    if (s->regs[SONIC_RCR] & SONIC_RCR_LPKT) {
+        /* Read next RRA */
+        dp8393x_do_read_rra(s);
     }
 
     /* Done */
Signature · 1 line
2.24.1
author
#14 lore raw

PATCH v4 13/14 dp8393x: Don't reset Silicon Revision register

In reply to Finn Thain

The jazzsonic driver in Linux uses the Silicon Revision register value to probe the chip. The driver fails unless the SR register contains 4. Unfortunately, reading this register in QEMU usually returns 0 because the s->regs[] array gets wiped after a software reset.

Fixes bd8f1ebce4 ("net/dp8393x: fix hardware reset")

---
Changed since v3:
- Simplified as per suggestion from Philippe Mathieu-Daudé.

---
 hw/net/dp8393x.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
hw/net/dp8393x.c +1 -1
index 1b73a8703b..93eb07e6c8 100644
@@ -919,6 +919,7 @@ static void dp8393x_reset(DeviceState *dev)
     timer_del(s->watchdog);
 
     memset(s->regs, 0, sizeof(s->regs));
+    s->regs[SONIC_SR] = 0x0004; /* only revision recognized by Linux/mips */
     s->regs[SONIC_CR] = SONIC_CR_RST | SONIC_CR_STP | SONIC_CR_RXDIS;
     s->regs[SONIC_DCR] &= ~(SONIC_DCR_EXBUS | SONIC_DCR_LBR);
     s->regs[SONIC_RCR] &= ~(SONIC_RCR_LB0 | SONIC_RCR_LB1 | SONIC_RCR_BRD | SONIC_RCR_RNT);
@@ -971,7 +972,6 @@ static void dp8393x_realize(DeviceState *dev, Error **errp)
     qemu_format_nic_info_str(qemu_get_queue(s->nic), s->conf.macaddr.a);
 
     s->watchdog = timer_new_ns(QEMU_CLOCK_VIRTUAL, dp8393x_watchdog, s);
-    s->regs[SONIC_SR] = 0x0004; /* only revision recognized by Linux */
 
     memory_region_init_ram(&s->prom, OBJECT(dev),
                            "dp8393x-prom", SONIC_PROM_SIZE, &local_err);
Signature · 1 line
2.24.1
Reviewed-by on v4 13/14
#15 lore raw

Re: [PATCH v4 13/14] dp8393x: Don't reset Silicon Revision register

Quoted 20 lines · Finn Thain

The jazzsonic driver in Linux uses the Silicon Revision register value to probe the chip. The driver fails unless the SR register contains 4. Unfortunately, reading this register in QEMU usually returns 0 because the s->regs[] array gets wiped after a software reset.

Fixes bd8f1ebce4 ("net/dp8393x: fix hardware reset")

---
Changed since v3:
- Simplified as per suggestion from Philippe Mathieu-Daudé.

---
  hw/net/dp8393x.c | 2 +-
  1 file changed, 1 insertion(+), 1 deletion(-)
hw/net/dp8393x.c +0 -0
index 1b73a8703b..93eb07e6c8 100644

hw/net/dp8393x.c static void dp8393x_reset(DeviceState *dev) · line 925

Quoted 7 lines
hw/net/dp8393x.c +1 -0
@@ -919,6 +919,7 @@ static void dp8393x_reset(DeviceState *dev)
      timer_del(s->watchdog);
 
      memset(s->regs, 0, sizeof(s->regs));
+    s->regs[SONIC_SR] = 0x0004; /* only revision recognized by Linux/mips */
      s->regs[SONIC_CR] = SONIC_CR_RST | SONIC_CR_STP | SONIC_CR_RXDIS;
      s->regs[SONIC_DCR] &= ~(SONIC_DCR_EXBUS | SONIC_DCR_LBR);
      s->regs[SONIC_RCR] &= ~(SONIC_RCR_LB0 | SONIC_RCR_LB1 | SONIC_RCR_BRD | SONIC_RCR_RNT);
Quoted 9 lines
hw/net/dp8393x.c +0 -1
@@ -971,7 +972,6 @@ static void dp8393x_realize(DeviceState *dev, Error **errp)
      qemu_format_nic_info_str(qemu_get_queue(s->nic), s->conf.macaddr.a);
 
      s->watchdog = timer_new_ns(QEMU_CLOCK_VIRTUAL, dp8393x_watchdog, s);
-    s->regs[SONIC_SR] = 0x0004; /* only revision recognized by Linux */
 
      memory_region_init_ram(&s->prom, OBJECT(dev),
                             "dp8393x-prom", SONIC_PROM_SIZE, &local_err);
author
#16 lore raw

PATCH v4 14/14 dp8393x: Don't stop reception upon RBE interrupt assertion

In reply to Finn Thain

Section 3.4.7 of the datasheet explains that,

The RBE bit in the Interrupt Status register is set when the SONIC finishes using the second to last receive buffer and reads the last RRA descriptor. Actually, the SONIC is not truly out of resources, but gives the system an early warning of an impending out of resources condition.

RBE does not mean actual receive buffer exhaustion, and reception should not be stopped. This is important because Linux will not check and clear the RBE interrupt until it receives another packet. But that won't happen if can_receive returns false. This bug causes the SONIC to become deaf (until reset).

Fix this with a new flag to indicate actual receive buffer exhaustion.

---
Changed since v2:
- Don't use can_receive to suspend packet reception.
- Don't misuse the RBE interrupt flag as a proxy for RRP == RWP.

---
 hw/net/dp8393x.c | 35 ++++++++++++++++++++++-------------
 1 file changed, 22 insertions(+), 13 deletions(-)
hw/net/dp8393x.c +22 -13
index 93eb07e6c8..cb55913a8a 100644
@@ -158,6 +158,7 @@ typedef struct dp8393xState {
     /* Hardware */
     uint8_t it_shift;
     bool big_endian;
+    bool last_rba_is_full;
     qemu_irq irq;
 #ifdef DEBUG_SONIC
     int irq_level;
@@ -347,12 +348,15 @@ static void dp8393x_do_read_rra(dp8393xState *s)
         s->regs[SONIC_RRP] = s->regs[SONIC_RSA];
     }
 
-    /* Check resource exhaustion */
+    /* Warn the host if CRBA now has the last available resource */
     if (s->regs[SONIC_RRP] == s->regs[SONIC_RWP])
     {
         s->regs[SONIC_ISR] |= SONIC_ISR_RBE;
         dp8393x_update_irq(s);
     }
+
+    /* Allow packet reception */
+    s->last_rba_is_full = false;
 }
 
 static void dp8393x_do_software_reset(dp8393xState *s)
@@ -659,9 +663,6 @@ static void dp8393x_write(void *opaque, hwaddr addr, uint64_t data,
                 dp8393x_do_read_rra(s);
             }
             dp8393x_update_irq(s);
-            if (dp8393x_can_receive(s->nic->ncs)) {
-                qemu_flush_queued_packets(qemu_get_queue(s->nic));
-            }
             break;
         /* The guest is required to store aligned pointers here */
         case SONIC_RSA:
@@ -721,8 +722,6 @@ static int dp8393x_can_receive(NetClientState *nc)
 
     if (!(s->regs[SONIC_CR] & SONIC_CR_RXEN))
         return 0;
-    if (s->regs[SONIC_ISR] & SONIC_ISR_RBE)
-        return 0;
     return 1;
 }
 
@@ -773,6 +772,10 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
     s->regs[SONIC_RCR] &= ~(SONIC_RCR_PRX | SONIC_RCR_LBK | SONIC_RCR_FAER |
         SONIC_RCR_CRCR | SONIC_RCR_LPKT | SONIC_RCR_BC | SONIC_RCR_MC);
 
+    if (s->last_rba_is_full) {
+        return pkt_size;
+    }
+
     rx_len = pkt_size + sizeof(checksum);
     if (s->regs[SONIC_DCR] & SONIC_DCR_DW) {
         width = 2;
@@ -786,8 +789,8 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
         DPRINTF("oversize packet, pkt_size is %d\n", pkt_size);
         s->regs[SONIC_ISR] |= SONIC_ISR_RBAE;
         dp8393x_update_irq(s);
-        dp8393x_do_read_rra(s);
-        return pkt_size;
+        s->regs[SONIC_RCR] |= SONIC_RCR_LPKT;
+        goto done;
     }
 
     packet_type = dp8393x_receive_filter(s, buf, pkt_size);
@@ -899,17 +902,23 @@ static ssize_t dp8393x_receive(NetClientState *nc, const uint8_t * buf,
         s->regs[SONIC_ISR] |= SONIC_ISR_PKTRX;
     }
 
+    dp8393x_update_irq(s);
+
     s->regs[SONIC_RSC] = (s->regs[SONIC_RSC] & 0xff00) |
                          ((s->regs[SONIC_RSC] + 1) & 0x00ff);
 
+done:
+
     if (s->regs[SONIC_RCR] & SONIC_RCR_LPKT) {
-        /* Read next RRA */
-        dp8393x_do_read_rra(s);
+        if (s->regs[SONIC_RRP] == s->regs[SONIC_RWP]) {
+            /* Stop packet reception */
+            s->last_rba_is_full = true;
+        } else {
+            /* Read next resource */
+            dp8393x_do_read_rra(s);
+        }
     }
 
-    /* Done */
-    dp8393x_update_irq(s);
-
     return pkt_size;
 }
 
Signature · 1 line
2.24.1
Applied
#17 lore raw
In reply to Finn Thain
Quoted 52 lines · Finn Thain

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely trigger an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---
Changed since v1:
- Minor revisions as described beneath commit logs.
- Dropped patches 4/10 and 7/10.
- Added 5 new patches.

Changed since v2:
- Minor revisions as described beneath commit logs.
- Dropped patch 13/13.
- Added 2 new patches.

Changed since v3:
- Replaced patch 13/14 with patch suggested by Philippe Mathieu-Daudé.

Finn Thain (14):
dp8393x: Mask EOL bit from descriptor addresses
dp8393x: Always use 32-bit accesses
dp8393x: Clean up endianness hacks
dp8393x: Have dp8393x_receive() return the packet size
dp8393x: Update LLFA and CRDA registers from rx descriptor
dp8393x: Clear RRRA command register bit only when appropriate
dp8393x: Implement packet size limit and RBAE interrupt
dp8393x: Don't clobber packet checksum
dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
dp8393x: Pad frames to word or long word boundary
dp8393x: Clear descriptor in_use field to release packet
dp8393x: Always update RRA pointers and sequence numbers
dp8393x: Don't reset Silicon Revision register
dp8393x: Don't stop reception upon RBE interrupt assertion

Quoted 2 lines
  hw/net/dp8393x.c | 202 +++++++++++++++++++++++++++++++----------------
  1 file changed, 134 insertions(+), 68 deletions(-)

Applied.

Thanks

#18 lore raw
Quoted 55 lines · Jason Wang
Quoted 52 lines · Finn Thain

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely trigger an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---
Changed since v1:
- Minor revisions as described beneath commit logs.
- Dropped patches 4/10 and 7/10.
- Added 5 new patches.

Changed since v2:
- Minor revisions as described beneath commit logs.
- Dropped patch 13/13.
- Added 2 new patches.

Changed since v3:
- Replaced patch 13/14 with patch suggested by Philippe Mathieu-Daudé.

Finn Thain (14):
dp8393x: Mask EOL bit from descriptor addresses
dp8393x: Always use 32-bit accesses
dp8393x: Clean up endianness hacks
dp8393x: Have dp8393x_receive() return the packet size
dp8393x: Update LLFA and CRDA registers from rx descriptor
dp8393x: Clear RRRA command register bit only when appropriate
dp8393x: Implement packet size limit and RBAE interrupt
dp8393x: Don't clobber packet checksum
dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
dp8393x: Pad frames to word or long word boundary
dp8393x: Clear descriptor in_use field to release packet
dp8393x: Always update RRA pointers and sequence numbers
dp8393x: Don't reset Silicon Revision register
dp8393x: Don't stop reception upon RBE interrupt assertion

Quoted 8 lines
Quoted 3 lines
  hw/net/dp8393x.c | 202 +++++++++++++++++++++++++++++++----------------
  1 file changed, 134 insertions(+), 68 deletions(-)

Applied.

Hi, Jason,

I generally have some reservations towards patches that did not receive any R-bs. I think we should hear from Herve in this case, to confirm that this change doesn't cause other problems while solving the original ones.

I hope this is not the case.

Regards,
Aleksandar

Quoted 4 lines

Thanks

#19 lore raw
Quoted 70 lines · Aleksandar Markovic

On Tuesday, February 4, 2020, Jason Wang <[email protected] <mailto:[email protected]>> wrote:

On 2020/1/29 下午5:27, Finn Thain wrote:

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely trigger
an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe
the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be
fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---
Changed since v1:
  - Minor revisions as described beneath commit logs.
  - Dropped patches 4/10 and 7/10.
  - Added 5 new patches.

Changed since v2:
  - Minor revisions as described beneath commit logs.
  - Dropped patch 13/13.
  - Added 2 new patches.

Changed since v3:
  - Replaced patch 13/14 with patch suggested by Philippe Mathieu-Daudé.

Finn Thain (14):
   dp8393x: Mask EOL bit from descriptor addresses
   dp8393x: Always use 32-bit accesses
   dp8393x: Clean up endianness hacks
   dp8393x: Have dp8393x_receive() return the packet size
   dp8393x: Update LLFA and CRDA registers from rx descriptor
   dp8393x: Clear RRRA command register bit only when appropriate
   dp8393x: Implement packet size limit and RBAE interrupt
   dp8393x: Don't clobber packet checksum
   dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
   dp8393x: Pad frames to word or long word boundary
   dp8393x: Clear descriptor in_use field to release packet
   dp8393x: Always update RRA pointers and sequence numbers
   dp8393x: Don't reset Silicon Revision register
   dp8393x: Don't stop reception upon RBE interrupt assertion

  hw/net/dp8393x.c | 202
+++++++++++++++++++++++++++++++----------------
  1 file changed, 134 insertions(+), 68 deletions(-)

Quoted 6 lines

Applied.

Hi, Jason,

I generally have some reservations towards patches that did not receive any R-bs. I think we should hear from Herve in this case, to confirm that this change doesn't cause other problems while solving the original ones.

That's fine but if it's agreed that we should hear from somebody for a specific part of the code, it's better to have the one as maintainer/reviewer in MAINTAINERS.

Thanks

Quoted 7 lines

I hope this is not the case.

Regards,
Aleksandar

#20 lore raw
In reply to Finn Thain
Quoted 14 lines · Finn Thain

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely trigger an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Quoted 8 lines

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---

Herve,

Do your Jazz tests pass with these changes?

Regards,
Aleksandar

Quoted 38 lines

Changed since v1:
- Minor revisions as described beneath commit logs.
- Dropped patches 4/10 and 7/10.
- Added 5 new patches.

Changed since v2:
- Minor revisions as described beneath commit logs.
- Dropped patch 13/13.
- Added 2 new patches.

Changed since v3:
- Replaced patch 13/14 with patch suggested by Philippe Mathieu-Daudé.

Finn Thain (14):
dp8393x: Mask EOL bit from descriptor addresses
dp8393x: Always use 32-bit accesses
dp8393x: Clean up endianness hacks
dp8393x: Have dp8393x_receive() return the packet size
dp8393x: Update LLFA and CRDA registers from rx descriptor
dp8393x: Clear RRRA command register bit only when appropriate
dp8393x: Implement packet size limit and RBAE interrupt
dp8393x: Don't clobber packet checksum
dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
dp8393x: Pad frames to word or long word boundary
dp8393x: Clear descriptor in_use field to release packet
dp8393x: Always update RRA pointers and sequence numbers
dp8393x: Don't reset Silicon Revision register
dp8393x: Don't stop reception upon RBE interrupt assertion

 hw/net/dp8393x.c | 202 +++++++++++++++++++++++++++++++----------------
 1 file changed, 134 insertions(+), 68 deletions(-)

--
2.24.1

author
#21 lore raw
Quoted 23 lines · Aleksandar Markovic
Quoted 20 lines · Finn Thain

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely trigger an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

Quoted 8 lines
Quoted 2 lines

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---

Herve,

Do your Jazz tests pass with these changes?

AFAIK those tests did not expose the NetBSD panic that is caused by mainline QEMU (mentioned above).

I have actually run the tests you requested (Hervé described them in an earlier thread). There was no regression. Quite the reverse -- it's no longer possible to remotely crash the NetBSD kernel.

Apparently my testing was also the first time that the jazzsonic driver (from the Linux/mips Magnum port) was tested successfully with QEMU. It doesn't work in mainline QEMU.

Anyway, more testing is always nice, and I'd certainly welcome an 'acked-by' or 'tested-by' if Hervé would like to send one.

Please consider backporting this series of bug fixes to QEMU stable branch(es).

Regards,
Finn

Quoted 44 lines

Regards,
Aleksandar

Quoted 38 lines

Changed since v1:
- Minor revisions as described beneath commit logs.
- Dropped patches 4/10 and 7/10.
- Added 5 new patches.

Changed since v2:
- Minor revisions as described beneath commit logs.
- Dropped patch 13/13.
- Added 2 new patches.

Changed since v3:
- Replaced patch 13/14 with patch suggested by Philippe Mathieu-Daudé.

Finn Thain (14):
dp8393x: Mask EOL bit from descriptor addresses
dp8393x: Always use 32-bit accesses
dp8393x: Clean up endianness hacks
dp8393x: Have dp8393x_receive() return the packet size
dp8393x: Update LLFA and CRDA registers from rx descriptor
dp8393x: Clear RRRA command register bit only when appropriate
dp8393x: Implement packet size limit and RBAE interrupt
dp8393x: Don't clobber packet checksum
dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
dp8393x: Pad frames to word or long word boundary
dp8393x: Clear descriptor in_use field to release packet
dp8393x: Always update RRA pointers and sequence numbers
dp8393x: Don't reset Silicon Revision register
dp8393x: Don't stop reception upon RBE interrupt assertion

 hw/net/dp8393x.c | 202 +++++++++++++++++++++++++++++++----------------
 1 file changed, 134 insertions(+), 68 deletions(-)

--
2.24.1

#22 lore raw

2:06 AM Sre, 19.02.2020. Finn Thain <[email protected]> је написао/ла:

Quoted 38 lines · Aleksandar Markovic
Quoted 24 lines
Quoted 20 lines · Finn Thain

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely trigger an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

Quoted 8 lines
Quoted 2 lines

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---

Herve,

Do your Jazz tests pass with these changes?

AFAIK those tests did not expose the NetBSD panic that is caused by mainline QEMU (mentioned above).

Quoted 8 lines

I have actually run the tests you requested (Hervé described them in an earlier thread). There was no regression. Quite the reverse -- it's no longer possible to remotely crash the NetBSD kernel.

Apparently my testing was also the first time that the jazzsonic driver (from the Linux/mips Magnum port) was tested successfully with QEMU. It doesn't work in mainline QEMU.

Well, I appologize if I missed all these facts. I just did not notice them, at least not in this form. And, yes, some "Tested-by:" by Herve would be desirable and nice.

Yours,
Aleksandae

Quoted 26 lines

Anyway, more testing is always nice, and I'd certainly welcome an 'acked-by' or 'tested-by' if Hervé would like to send one.

Please consider backporting this series of bug fixes to QEMU stable branch(es).

Regards,
Finn

Quoted 17 lines

Regards,
Aleksandar

Quoted 12 lines

Changed since v1:
- Minor revisions as described beneath commit logs.
- Dropped patches 4/10 and 7/10.
- Added 5 new patches.

Changed since v2:
- Minor revisions as described beneath commit logs.
- Dropped patch 13/13.
- Added 2 new patches.

Changed since v3:
- Replaced patch 13/14 with patch suggested by Philippe

Mathieu-Daudé.

Quoted 18 lines
Quoted 18 lines
Quoted 18 lines

Finn Thain (14):
dp8393x: Mask EOL bit from descriptor addresses
dp8393x: Always use 32-bit accesses
dp8393x: Clean up endianness hacks
dp8393x: Have dp8393x_receive() return the packet size
dp8393x: Update LLFA and CRDA registers from rx descriptor
dp8393x: Clear RRRA command register bit only when appropriate
dp8393x: Implement packet size limit and RBAE interrupt
dp8393x: Don't clobber packet checksum
dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
dp8393x: Pad frames to word or long word boundary
dp8393x: Clear descriptor in_use field to release packet
dp8393x: Always update RRA pointers and sequence numbers
dp8393x: Don't reset Silicon Revision register
dp8393x: Don't stop reception upon RBE interrupt assertion

Quoted 1 line
Quoted 1 line
Quoted 1 line
 hw/net/dp8393x.c | 202

+++++++++++++++++++++++++++++++----------------

Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
 1 file changed, 134 insertions(+), 68 deletions(-)

--
2.24.1

#23 lore raw

2:54 AM Sre, 19.02.2020. Aleksandar Markovic <[email protected]> је написао/ла:

Quoted 2 lines

2:06 AM Sre, 19.02.2020. Finn Thain <[email protected]> је

написао/ла:

Quoted 5 lines
Quoted 4 lines · Aleksandar Markovic
Quoted 2 lines

On Wednesday, January 29, 2020, Finn Thain <[email protected]

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 6 lines · wrote:

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely

trigger

Quoted 30 lines
Quoted 30 lines
Quoted 14 lines
Quoted 14 lines

an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

Quoted 8 lines
Quoted 2 lines

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---

Herve,

Do your Jazz tests pass with these changes?

AFAIK those tests did not expose the NetBSD panic that is caused by mainline QEMU (mentioned above).

I have actually run the tests you requested (Hervé described them in an earlier thread). There was no regression. Quite the reverse -- it's no longer possible to remotely crash the NetBSD kernel.

Quoted 6 lines
Quoted 4 lines

Apparently my testing was also the first time that the jazzsonic driver (from the Linux/mips Magnum port) was tested successfully with QEMU. It doesn't work in mainline QEMU.

Well, I appologize if I missed all these facts. I just did not notice

them, at least not in this form. And, yes, some "Tested-by:" by Herve would be desirable and nice.

Quoted 1 line

Or, perhaps, even "Reviewed-by:".

Quoted 29 lines

Yours,
Aleksandae

Quoted 26 lines

Anyway, more testing is always nice, and I'd certainly welcome an 'acked-by' or 'tested-by' if Hervé would like to send one.

Please consider backporting this series of bug fixes to QEMU stable branch(es).

Regards,
Finn

Quoted 17 lines

Regards,
Aleksandar

Quoted 12 lines

Changed since v1:
- Minor revisions as described beneath commit logs.
- Dropped patches 4/10 and 7/10.
- Added 5 new patches.

Changed since v2:
- Minor revisions as described beneath commit logs.
- Dropped patch 13/13.
- Added 2 new patches.

Changed since v3:
- Replaced patch 13/14 with patch suggested by Philippe

Mathieu-Daudé.

Quoted 18 lines
Quoted 18 lines
Quoted 18 lines
Quoted 18 lines

Finn Thain (14):
dp8393x: Mask EOL bit from descriptor addresses
dp8393x: Always use 32-bit accesses
dp8393x: Clean up endianness hacks
dp8393x: Have dp8393x_receive() return the packet size
dp8393x: Update LLFA and CRDA registers from rx descriptor
dp8393x: Clear RRRA command register bit only when appropriate
dp8393x: Implement packet size limit and RBAE interrupt
dp8393x: Don't clobber packet checksum
dp8393x: Use long-word-aligned RRA pointers in 32-bit mode
dp8393x: Pad frames to word or long word boundary
dp8393x: Clear descriptor in_use field to release packet
dp8393x: Always update RRA pointers and sequence numbers
dp8393x: Don't reset Silicon Revision register
dp8393x: Don't stop reception upon RBE interrupt assertion

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
 hw/net/dp8393x.c | 202

+++++++++++++++++++++++++++++++----------------

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines
 1 file changed, 134 insertions(+), 68 deletions(-)

--
2.24.1

#24 lore raw

Le 19/02/2020 à 02:57, Aleksandar Markovic a écrit :

Quoted 55 lines

2:54 AM Sre, 19.02.2020. Aleksandar Markovic <[email protected] <mailto:[email protected]>> је написао/ла:

Quoted 2 lines

2:06 AM Sre, 19.02.2020. Finn Thain <[email protected]

<mailto:[email protected]>> је написао/ла:

Quoted 4 lines
Quoted 4 lines · Aleksandar Markovic
Quoted 2 lines

On Wednesday, January 29, 2020, Finn Thain

<[email protected] <mailto:[email protected]>>

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 6 lines · wrote:

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely

trigger

Quoted 35 lines
Quoted 34 lines
Quoted 14 lines
Quoted 14 lines

an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

Quoted 8 lines
Quoted 2 lines

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---

Herve,

Do your Jazz tests pass with these changes?

AFAIK those tests did not expose the NetBSD panic that is caused by mainline QEMU (mentioned above).

I have actually run the tests you requested (Hervé described them in an earlier thread). There was no regression. Quite the reverse -- it's no longer possible to remotely crash the NetBSD kernel.

Apparently my testing was also the first time that the jazzsonic driver (from the Linux/mips Magnum port) was tested successfully with QEMU. It doesn't work in mainline QEMU.

Quoted 7 lines
Quoted 1 line

Well, I appologize if I missed all these facts. I just did not notice

them, at least not in this form. And, yes, some "Tested-by:" by Herve would be desirable and nice.

Quoted 1 line

Or, perhaps, even "Reviewed-by:".

It would be nice to have this merged before next release because q800 machine networking is not reliable without them.

And thank you to Finn for all his hard work on this device emulation.

Laurent

#25 lore raw
Quoted 59 lines · Laurent Vivier

Le 19/02/2020 à 02:57, Aleksandar Markovic a écrit :

Quoted 58 lines

2:54 AM Sre, 19.02.2020. Aleksandar Markovic <[email protected] <mailto:[email protected]>> је написао/ла:

Quoted 2 lines

2:06 AM Sre, 19.02.2020. Finn Thain <[email protected]

<mailto:[email protected]>> је написао/ла:

Quoted 4 lines
Quoted 4 lines · Aleksandar Markovic
Quoted 2 lines

On Wednesday, January 29, 2020, Finn Thain

<[email protected] <mailto:[email protected]>>

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 6 lines · wrote:

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely

trigger

Quoted 30 lines
Quoted 30 lines
Quoted 14 lines
Quoted 14 lines

an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

This patch series resolves these bugs.

Quoted 8 lines
Quoted 2 lines

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---

Herve,

Do your Jazz tests pass with these changes?

AFAIK those tests did not expose the NetBSD panic that is caused by mainline QEMU (mentioned above).

I have actually run the tests you requested (Hervé described them in an earlier thread). There was no regression. Quite the reverse -- it's no longer possible to remotely crash the NetBSD kernel.

Quoted 6 lines
Quoted 4 lines

Apparently my testing was also the first time that the jazzsonic driver (from the Linux/mips Magnum port) was tested successfully with QEMU. It doesn't work in mainline QEMU.

Well, I appologize if I missed all these facts. I just did not notice

them, at least not in this form. And, yes, some "Tested-by:" by Herve would be desirable and nice.

FWIW I tested Finn kernel and QEMU part following:
https://www.mail-archive.com/[email protected]/msg667432.html
to check than its series doesn't introduce regressions, booting Linux and NetBSD.
I haven't run the thorough networking tests Laurent do with the q800 (scp of big files, fetch over http in loop).

Hervé testing is welcomed, but as a hobbyist he doesn't spend more than 1h every 2 months on this, so I don't think his approval is a blocker. We are not talking about business critical emulation, so we can fix regressions on top.

--

That said, I'm spending some hobby time on a Magnum boot code to be able to test the board upstream (without depending on proprietary BIOS and painful graphical setup).

Currently I get NetBSD to kdb and Linux get stuck there:
https://paste.debian.net/plain/1129965

Quoted 12 lines
Quoted 4 lines
Quoted 1 line

Or, perhaps, even "Reviewed-by:".

It would be nice to have this merged before next release because q800 machine networking is not reliable without them.

And thank you to Finn for all his hard work on this device emulation.

Laurent

#26 lore raw
In reply to Laurent Vivier
Quoted 51 lines · Laurent Vivier

Le 19/02/2020 à 02:57, Aleksandar Markovic a écrit :

Quoted 50 lines

2:54 AM Sre, 19.02.2020. Aleksandar Markovic <[email protected] <mailto:[email protected]>> је написао/ла:

Quoted 1 line

2:06 AM Sre, 19.02.2020. Finn Thain <[email protected]

<mailto:[email protected]>> је написао/ла:

Quoted 3 lines
Quoted 3 lines · Aleksandar Markovic
Quoted 2 lines

On Wednesday, January 29, 2020, Finn Thain

<[email protected] <mailto:[email protected]>>

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 6 lines · wrote:

Hi All,

There are bugs in the emulated dp8393x device that can stop packet reception in a Linux/m68k guest (q800 machine).

With a Linux/m68k v5.5 guest (q800), it's possible to remotely

trigger

Quoted 32 lines
Quoted 32 lines
Quoted 12 lines
Quoted 12 lines

an Oops by sending ping floods.

With a Linux/mips guest (magnum machine), the driver fails to probe the dp8393x device.

With a NetBSD/arc 5.1 guest (magnum), the bugs in the device can be fatal to the guest kernel.

Whilst debugging the device, I found that the receiver algorithm differs from the one described in the National Semiconductor datasheet.

Quoted 9 lines
Quoted 4 lines

This patch series resolves these bugs.

AFAIK, all bugs in the Linux sonic driver were fixed in Linux v5.5.
---

Herve,

Do your Jazz tests pass with these changes?

AFAIK those tests did not expose the NetBSD panic that is caused by mainline QEMU (mentioned above).

I have actually run the tests you requested (Hervé described them in an earlier thread). There was no regression. Quite the reverse -- it's no longer possible to remotely crash the NetBSD kernel.

Apparently my testing was also the first time that the jazzsonic driver (from the Linux/mips Magnum port) was tested successfully with QEMU. It doesn't work in mainline QEMU.

Quoted 7 lines
Quoted 5 lines
Quoted 1 line

Well, I appologize if I missed all these facts. I just did not notice

them, at least not in this form. And, yes, some "Tested-by:" by Herve would be desirable and nice.
Or, perhaps, even "Reviewed-by:".

It would be nice to have this merged before next release because q800 machine networking is not reliable without them.

I will send the pull request that contains this series before the end of this week.

Thanks

Quoted 8 lines

And thank you to Finn for all his hard work on this device emulation.

Laurent