Skip to contentSkip to conversation

platform/x86: int3472: add hpd pin support

PATCH In review Sakari Ailus 2 participants 2 messages Jul 2, 2025

Subsystems (3)
lore
Share & tools
lore

Sakari Ailus

author maintainer
#0 lore raw

PATCH v4 1/1 platform/x86: int3472: add hpd pin support

From: Dongcheng Yan <[email protected]>

Typically HDMI to MIPI CSI-2 bridges have a pin to signal image data is being received. On the host side this is wired to a GPIO for polling or interrupts. This includes the Lontium HDMI to MIPI CSI-2 bridges lt6911uxe and lt6911uxc.

The GPIO "hpd" is used already by other HDMI to CSI-2 bridges, use it here as well.

---
since v3:

- Rebase due to commit 53eddae9af0c0b46f9c77a02d23c21c1aa824739 ("platform/x86: int3472: Move common.h to public includes, symbols to INTEL_INT3472"), moving the new GPIO PIN definition from common.h to int3472.h.

The intent is to merge this via the media tree, with Ilpo's ack.

 drivers/platform/x86/intel/int3472/discrete.c | 6 ++++++
 include/linux/platform_data/x86/int3472.h     | 1 +
 2 files changed, 7 insertions(+)
drivers/platform/x86/intel/int3472/discrete.c +6 -0
index 4c0aed6e626f..bdfb8a800c54 100644
@@ -193,6 +193,10 @@ static void int3472_get_con_id_and_polarity(struct int3472_discrete_device *int3
 		*con_id = "privacy-led";
 		*gpio_flags = GPIO_ACTIVE_HIGH;
 		break;
+	case INT3472_GPIO_TYPE_HOTPLUG_DETECT:
+		*con_id = "hpd";
+		*gpio_flags = GPIO_ACTIVE_HIGH;
+		break;
 	case INT3472_GPIO_TYPE_POWER_ENABLE:
 		*con_id = "avdd";
 		*gpio_flags = GPIO_ACTIVE_HIGH;
@@ -223,6 +227,7 @@ static void int3472_get_con_id_and_polarity(struct int3472_discrete_device *int3
  * 0x0b Power enable
  * 0x0c Clock enable
  * 0x0d Privacy LED
+ * 0x13 Hotplug detect
  *
  * There are some known platform specific quirks where that does not quite
  * hold up; for example where a pin with type 0x01 (Power down) is mapped to
@@ -292,6 +297,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,
 	switch (type) {
 	case INT3472_GPIO_TYPE_RESET:
 	case INT3472_GPIO_TYPE_POWERDOWN:
+	case INT3472_GPIO_TYPE_HOTPLUG_DETECT:
 		ret = skl_int3472_map_gpio_to_sensor(int3472, agpio, con_id, gpio_flags);
 		if (ret)
 			err_msg = "Failed to map GPIO pin to sensor\n";
include/linux/platform_data/x86/int3472.h +1 -0
index 78276a11c48d..1571e9157fa5 100644
@@ -27,6 +27,7 @@
 #define INT3472_GPIO_TYPE_CLK_ENABLE				0x0c
 #define INT3472_GPIO_TYPE_PRIVACY_LED				0x0d
 #define INT3472_GPIO_TYPE_HANDSHAKE				0x12
+#define INT3472_GPIO_TYPE_HOTPLUG_DETECT			0x13
 
 #define INT3472_PDEV_MAX_NAME_LEN				23
 #define INT3472_MAX_SENSOR_GPIOS				3
Signature · 1 line
2.39.5
Reviewed-by on v4 1/1
#1 lore raw
Quoted 9 lines · Sakari Ailus

From: Dongcheng Yan <[email protected]>

Typically HDMI to MIPI CSI-2 bridges have a pin to signal image data is being received. On the host side this is wired to a GPIO for polling or interrupts. This includes the Lontium HDMI to MIPI CSI-2 bridges lt6911uxe and lt6911uxc.

The GPIO "hpd" is used already by other HDMI to CSI-2 bridges, use it here as well.

Signature · 2 lines
With Best Regards,
Andy Shevchenko