platform/x86: int3472: add hpd pin support
Sakari Ailus
maintainerPATCH v4 1/1 platform/x86: int3472: add hpd pin support
From: Dongcheng Yan <[email protected]>
Typically HDMI to MIPI CSI-2 bridges have a pin to signal image data is being received. On the host side this is wired to a GPIO for polling or interrupts. This includes the Lontium HDMI to MIPI CSI-2 bridges lt6911uxe and lt6911uxc.
The GPIO "hpd" is used already by other HDMI to CSI-2 bridges, use it here as well.
---
since v3:
- Rebase due to commit 53eddae9af0c0b46f9c77a02d23c21c1aa824739 ("platform/x86: int3472: Move common.h to public includes, symbols to INTEL_INT3472"), moving the new GPIO PIN definition from common.h to int3472.h.
The intent is to merge this via the media tree, with Ilpo's ack.
drivers/platform/x86/intel/int3472/discrete.c | 6 ++++++ include/linux/platform_data/x86/int3472.h | 1 + 2 files changed, 7 insertions(+)
drivers/platform/x86/intel/int3472/discrete.c +6 -0
@@ -193,6 +193,10 @@ static void int3472_get_con_id_and_polarity(struct int3472_discrete_device *int3 *con_id ="privacy-led" ; *gpio_flags =GPIO_ACTIVE_HIGH ;break ; +case INT3472_GPIO_TYPE_HOTPLUG_DETECT : + *con_id ="hpd" ; + *gpio_flags =GPIO_ACTIVE_HIGH ; +break ;case INT3472_GPIO_TYPE_POWER_ENABLE : *con_id ="avdd" ; *gpio_flags =GPIO_ACTIVE_HIGH ;
@@ -223,6 +227,7 @@ static void int3472_get_con_id_and_polarity(struct int3472_discrete_device *int3* 0x0b Power enable * 0x0c Clock enable * 0x0d Privacy LED +* 0x13 Hotplug detect * * There are some known platform specific quirks where that does not quite * hold up; for example where a pin with type 0x01 (Power down) is mapped to
@@ -292,6 +297,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,switch (type) {case INT3472_GPIO_TYPE_RESET :case INT3472_GPIO_TYPE_POWERDOWN : +case INT3472_GPIO_TYPE_HOTPLUG_DETECT : ret =skl_int3472_map_gpio_to_sensor (int3472, agpio, con_id, gpio_flags);if (ret) err_msg ="Failed to map GPIO pin to sensor\n" ;
include/linux/platform_data/x86/int3472.h +1 -0
@@ -27,6 +27,7 @@#define INT3472_GPIO_TYPE_CLK_ENABLE 0x0c#define INT3472_GPIO_TYPE_PRIVACY_LED 0x0d#define INT3472_GPIO_TYPE_HANDSHAKE 0x12 +#define INT3472_GPIO_TYPE_HOTPLUG_DETECT 0x13#define INT3472_PDEV_MAX_NAME_LEN 23#define INT3472_MAX_SENSOR_GPIOS 3
Signature · 1 line
2.39.5
Quoted 9 lines · Sakari Ailus
From: Dongcheng Yan <[email protected]>
Typically HDMI to MIPI CSI-2 bridges have a pin to signal image data is being received. On the host side this is wired to a GPIO for polling or interrupts. This includes the Lontium HDMI to MIPI CSI-2 bridges lt6911uxe and lt6911uxc.
The GPIO "hpd" is used already by other HDMI to CSI-2 bridges, use it here as well.
Signature · 2 lines
With Best Regards, Andy Shevchenko