Skip to contentSkip to conversation

Radxa ROCK 5T: SD card startup failure

DISCUSSION Michael Tretter 2 participants 2 messages Jan 9 – Feb 9

lore
Share & tools
lore
#0 lore raw

Hi,

since Commit a3bf6c16f77d ("dts: update to v6.19-rc1"), barebox fails to initialize the SD card on my Radxa ROCK T5 board.

I tracked the failure down to a change of the pinctrl setting for the card detect pin to RK_FUNC_GPIO (see sdmmc_det_pin). If I change the pinctrl mux back to 1, the SD card is initialized correctly.

If the error happens, the dw_mmc driver reports a DATA ERROR on CMD13 with BIT(13) set (DWMCI_INTMSK_SBE) and runs into a timeout afterward:

	dw_mmc [email protected]: registered as mmc1
	dw_mmc [email protected]: Using fifo-depth=256
	mmc1: clock 0.0MHz width 1 timing legacy
	dw_mmc [email protected]: Buswidth = 0, clock: 0
	mmc1: clock 0.400000MHz width 1 timing legacy
	dw_mmc [email protected]: Buswidth = 0, clock: 400000
	dw_mmc [email protected]: Sending CMD0
	dw_mmc [email protected]: Sending CMD8
	mmc1: SD Card Rev. 2.00 or later detected
	dw_mmc [email protected]: Sending CMD55
	dw_mmc [email protected]: Sending CMD41
	dw_mmc [email protected]: Sending CMD55
	dw_mmc [email protected]: Sending CMD41
	dw_mmc [email protected]: Sending CMD55
	dw_mmc [email protected]: Sending CMD41
	dw_mmc [email protected]: Sending CMD55
	dw_mmc [email protected]: Sending CMD41
	dw_mmc [email protected]: Sending CMD55
	dw_mmc [email protected]: Sending CMD41
	mmc1: Put the Card in Identify Mode
	dw_mmc [email protected]: Sending CMD2
	mmc1: Card's identification data is: 03534453-44333247-8555412B-AC0191F5
	mmc1: Get/Set relative address
	dw_mmc [email protected]: Sending CMD3
	mmc1: Get card's specific data
	dw_mmc [email protected]: Sending CMD9
	mmc1: Card's specific data is: 400E0032-5B590000-EDC87F80-0A4040C3
	mmc1: Transfer speed: 25000000
	mmc1: Max. block length are: Write=512, Read=512 Bytes
	mmc1: Read block length: 512, Write block length: 512
	mmc1: Select the card, and put it into Transfer Mode
	dw_mmc [email protected]: Sending CMD7
	mmc1: Changing transfer frequency
	dw_mmc [email protected]: Sending CMD55
	mmc1: Trying to read the SCR (try 1 of 3)
	dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000008 0xad25aac0 0xad25b010
	dw_mmc [email protected]: Sending CMD51
	dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25aac0 0xad25b010
	dw_mmc [email protected]: Sending CMD6
	dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25aac0 0xad25b010
	dw_mmc [email protected]: Sending CMD6
	mmc1: detected SD card version 2.0
	mmc1: Capacity: 30436 MiB
	mmc1: Erase group is 1 sector(s). Trim not supported
	mmc1: Prepare for bus width change
	dw_mmc [email protected]: Sending CMD55
	mmc1: Set SD bus width to 4 bit
	dw_mmc [email protected]: Sending CMD6
	mmc1: clock 0.400000MHz width 4 timing legacy
	dw_mmc [email protected]: Buswidth = 2, clock: 400000
	mmc1: clock 50.0MHz width 4 timing SD HS
	dw_mmc [email protected]: Buswidth = 2, clock: 50000000
	dw_mmc [email protected]: Sending CMD55
	dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010
	dw_mmc [email protected]: Sending CMD13
	dw_mmc [email protected]: DATA ERROR!
	dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010
	dw_mmc [email protected]: Sending CMD13
	dw_mmc [email protected]: Send command timeout..
	dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010
	dw_mmc [email protected]: Sending CMD13
	dw_mmc [email protected]: Send command timeout..
	dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010
	dw_mmc [email protected]: Sending CMD13
	dw_mmc [email protected]: Send command timeout..
	mmc1: unable to read ssr: Connection timed out
	dw_mmc [email protected]: Sending CMD16
	dw_mmc [email protected]: Send command timeout..
	dw_mmc [email protected]: Sending CMD16
	dw_mmc [email protected]: Send command timeout..
	dw_mmc [email protected]: Sending CMD16
	dw_mmc [email protected]: Send command timeout..
	dw_mmc [email protected]: Sending CMD16
	dw_mmc [email protected]: Send command timeout..
	dw_mmc [email protected]: Sending CMD16
	dw_mmc [email protected]: Send command timeout..
	WARNING: mmc1: Card's startup fails with -110

It seems to me that the SD host controller fails to correctly initialize if the card detect it directly muxed as GPIO instead of muxing it to the SD host controller. At least that's what I understand from
https://lore.kernel.org/linux-rockchip/4920950.GXAFRqVoOG@diego/.

May there be some configuration in the SD host controller that needs to be changed to ignore the card detect?

Michael

#1 lore raw

Hello Michael,

Quoted 7 lines · Michael Tretter

It seems to me that the SD host controller fails to correctly initialize if the card detect it directly muxed as GPIO instead of muxing it to the SD host controller. At least that's what I understand from
https://lore.kernel.org/linux-rockchip/4920950.GXAFRqVoOG@diego/.

May there be some configuration in the SD host controller that needs to be changed to ignore the card detect?

The driver didn't clear the card-detect bit in DWMCI_RINTSTS, which may be the culprit.

Could you please give the potential fix at [1] a test?

If this doesn't resolve the issue, we will have to do revert the DT change in arch/arm/dts before v2026.02.0.

[1]:
https://lore.barebox.org/barebox/[email protected]/T/#u

Thanks,
Ahmad

Quoted 4 lines

Michael

Signature · 4 lines
Pengutronix e.K.                  |                             |
Steuerwalder Str. 21              | http://www.pengutronix.de/  |
31137 Hildesheim, Germany         | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686  | Fax:   +49-5121-206917-5555 |