Radxa ROCK 5T: SD card startup failure
Hi,
since Commit a3bf6c16f77d ("dts: update to v6.19-rc1"), barebox fails to initialize the SD card on my Radxa ROCK T5 board.
I tracked the failure down to a change of the pinctrl setting for the card detect pin to RK_FUNC_GPIO (see sdmmc_det_pin). If I change the pinctrl mux back to 1, the SD card is initialized correctly.
If the error happens, the dw_mmc driver reports a DATA ERROR on CMD13 with BIT(13) set (DWMCI_INTMSK_SBE) and runs into a timeout afterward:
dw_mmc [email protected]: registered as mmc1 dw_mmc [email protected]: Using fifo-depth=256 mmc1: clock 0.0MHz width 1 timing legacy dw_mmc [email protected]: Buswidth = 0, clock: 0 mmc1: clock 0.400000MHz width 1 timing legacy dw_mmc [email protected]: Buswidth = 0, clock: 400000 dw_mmc [email protected]: Sending CMD0 dw_mmc [email protected]: Sending CMD8 mmc1: SD Card Rev. 2.00 or later detected dw_mmc [email protected]: Sending CMD55 dw_mmc [email protected]: Sending CMD41 dw_mmc [email protected]: Sending CMD55 dw_mmc [email protected]: Sending CMD41 dw_mmc [email protected]: Sending CMD55 dw_mmc [email protected]: Sending CMD41 dw_mmc [email protected]: Sending CMD55 dw_mmc [email protected]: Sending CMD41 dw_mmc [email protected]: Sending CMD55 dw_mmc [email protected]: Sending CMD41 mmc1: Put the Card in Identify Mode dw_mmc [email protected]: Sending CMD2 mmc1: Card's identification data is: 03534453-44333247-8555412B-AC0191F5 mmc1: Get/Set relative address dw_mmc [email protected]: Sending CMD3 mmc1: Get card's specific data dw_mmc [email protected]: Sending CMD9 mmc1: Card's specific data is: 400E0032-5B590000-EDC87F80-0A4040C3 mmc1: Transfer speed: 25000000 mmc1: Max. block length are: Write=512, Read=512 Bytes mmc1: Read block length: 512, Write block length: 512 mmc1: Select the card, and put it into Transfer Mode dw_mmc [email protected]: Sending CMD7 mmc1: Changing transfer frequency dw_mmc [email protected]: Sending CMD55 mmc1: Trying to read the SCR (try 1 of 3) dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000008 0xad25aac0 0xad25b010 dw_mmc [email protected]: Sending CMD51 dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25aac0 0xad25b010 dw_mmc [email protected]: Sending CMD6 dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25aac0 0xad25b010 dw_mmc [email protected]: Sending CMD6 mmc1: detected SD card version 2.0 mmc1: Capacity: 30436 MiB mmc1: Erase group is 1 sector(s). Trim not supported mmc1: Prepare for bus width change dw_mmc [email protected]: Sending CMD55 mmc1: Set SD bus width to 4 bit dw_mmc [email protected]: Sending CMD6 mmc1: clock 0.400000MHz width 4 timing legacy dw_mmc [email protected]: Buswidth = 2, clock: 400000 mmc1: clock 50.0MHz width 4 timing SD HS dw_mmc [email protected]: Buswidth = 2, clock: 50000000 dw_mmc [email protected]: Sending CMD55 dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010 dw_mmc [email protected]: Sending CMD13 dw_mmc [email protected]: DATA ERROR! dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010 dw_mmc [email protected]: Sending CMD13 dw_mmc [email protected]: Send command timeout.. dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010 dw_mmc [email protected]: Sending CMD13 dw_mmc [email protected]: Send command timeout.. dw_mmc [email protected]: desc@ 0x00000000ad25b000 0x8000001c 0x00000040 0xad25d780 0xad25b010 dw_mmc [email protected]: Sending CMD13 dw_mmc [email protected]: Send command timeout.. mmc1: unable to read ssr: Connection timed out dw_mmc [email protected]: Sending CMD16 dw_mmc [email protected]: Send command timeout.. dw_mmc [email protected]: Sending CMD16 dw_mmc [email protected]: Send command timeout.. dw_mmc [email protected]: Sending CMD16 dw_mmc [email protected]: Send command timeout.. dw_mmc [email protected]: Sending CMD16 dw_mmc [email protected]: Send command timeout.. dw_mmc [email protected]: Sending CMD16 dw_mmc [email protected]: Send command timeout.. WARNING: mmc1: Card's startup fails with -110
It seems to me that the SD host controller fails to correctly initialize if the card detect it directly muxed as GPIO instead of muxing it to the SD host controller. At least that's what I understand from
https://lore.kernel.org/linux-rockchip/4920950.GXAFRqVoOG@diego/.
May there be some configuration in the SD host controller that needs to be changed to ignore the card detect?
Michael
Hello Michael,
Quoted 7 lines · Michael Tretter
It seems to me that the SD host controller fails to correctly initialize if the card detect it directly muxed as GPIO instead of muxing it to the SD host controller. At least that's what I understand from
https://lore.kernel.org/linux-rockchip/4920950.GXAFRqVoOG@diego/.May there be some configuration in the SD host controller that needs to be changed to ignore the card detect?
The driver didn't clear the card-detect bit in DWMCI_RINTSTS, which may be the culprit.
Could you please give the potential fix at [1] a test?
If this doesn't resolve the issue, we will have to do revert the DT change in arch/arm/dts before v2026.02.0.
[1]:
https://lore.barebox.org/barebox/[email protected]/T/#u
Thanks,
Ahmad
Quoted 4 lines
Michael
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |