net: dsa: initial support for MaxLinear MxL862xx switches
Subsystems (6)
Daniel Golle
maintainerv12 cover net: dsa: initial support for MaxLinear MxL862xx switches
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
MxL862xx integrates a firmware running on an embedded processor (based on Zephyr RTOS). Host interaction uses a simple netlink-like API transported over MDIO/MMD.
This series includes only what's needed to pass traffic between user ports and the CPU port: relayed MDIO to internal PHYs, basic port enable/disable, and CPU-port special tagging.
The SerDes interface of the CPU port is automatically configured by the switch after reset using a board-specific configuration stored together with the firmware in the flash chip attached to the switch, so no action is needed from the driver to setup the interface mode of the CPU port.
Also MAC settings of the PHY ports are automatically configured, which means the driver works fine with phylink_mac_ops being all no-op stubs.
Multiple follow up series will bring support for setting up the other SerDes PCS interface (ie. not used for the CPU port), bridge, VLAN, ... offloading, and support for using an 802.1Q-based special tag instead of the proprietary 8-byte tag.
---
basic DSA selftests were run, results:
* no_forwarding.sh: all tests PASS
* bridge_vlan_unaware.sh: all tests PASS
* bridge_vlan_mcast.sh: all tests PASS
* bridge_vlan_aware.sh: all tests PASS
* local_termination.sh: all tests PASS or XFAIL, except for
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address [FAIL]
reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address, allmulti [FAIL]
reception succeeded, but should have failed
As obviously this is mostly testing the Linux software bridge at this point so I didn't bother to run any of the FDB or MDB related tests.
Some mystery about the relationship between the sub-interface ID and CTP port assignment remains for now, so I cannot yet fully explain the magic numbers when calculating the two.
(Why is it neccesary to allocate 23 CTPs when using port 9 as CPU port while there are at most 17 phyiscal interfaces in total, and only at most 13 when using one of the two SerDes as CPU interface? Why is there an offset of 16 when calculating the sub-interface ID? How will a total of 17 ports be possibly represented in a 4-bit field in the tag RX path?)
At this point this doesn't impact functionality, and I hope for further clarification discussing all that with MaxLinear engineers.
I believe the initial driver is anyway in good shape now, a follow-up series addressing configuring the SerDes interfaces will also have to take care of CTP assignment and sub-interfaces to not hit the mentioned 4-bit cap in the tag driver.
Changes since v11:
Address comments reported by Jakub Kicinski using netdev-ai
https://patchwork.kernel.org/comment/26767905/
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* list switch variants in Kconfig starting with dash ('-')
* remove the __packed attribute on structs which are naturally packed according to C rules (ie. one other struct with only a single byte-aligned member)
* log error in mxl862xx_port_disable()
* introduce !NULL check for return value of dsa_to_port() in mxl862xx_add_single_port_bridge
* check cpu_dp being non-NULL before dereferencing dp->cpu_dp
* use non-racy and deterministic name for MII bus
* skip ports without cpu_dp assigned in mxl862xx_setup_cpu_bridge() to avoid potential NULL-pointer dereference
* call dev_set_drvdata() only after dsa_register_switch() has been successfully completed
Changes since v10:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* arrange local variables in reverse xmas tree order (again)
* use MXL862_NAME as .name in struct dsa_device_ops
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix fatal last-second changes dsa_port_is_unused vs. dsa_is_unused_port and dsa_port_is_unused vs. dsa_is_unused_port
* use cpu_to_le16 in mxl862xx_configure_ctp_port
* improve formatting of some kerneldoc comments
Changes since v9:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* add microcontroller port 0
2/4 net: dsa: add tag format for MxL862xx switches
* count ports starting from 0
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix indentation in kernel-doc
* remove misleading comment regarding sub-interface IDs
* remove unused macros, set MXL862XX_MAX_PORTS to 17
* count ports starting from 0, 0 being the microcontroller
* improve port setup:
- split tag protocol and CTP port assignment
- use ports cpu_dp instead of relying on single (ie. first) CPU port
- handle CPU port like any other port
- prepare forward DT compatibility with multiple CPU ports
Changes since v8:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* remove practically unused struct hw_info
* lots of kerneldoc improvements in mxl862xx-api.h
* drop .mac_select_pcs() stub
* better handling for firmware error return value
* apply reverse xmas tree in mxl862xx_api_wrap
* guard headers with #ifdef macro
* include net/dsa.h and linux/mdio.h in mxl862xx.h
* call mxl862xx_port_fast_age() only once in .port_setup
* don't create isolation bridges for unused ports
* replace errornous cast with correct range of values denoting firmware errors
Changes since v7
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* use little-endian in bridge_port_config API
* remove duplciate assignment of br_port_cfg.bridge_port_id when setting up CPU port
Changes since v6
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix kerneldoc style
Changes since RFC v5
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* remove unnecessary check for skb != NULL
* merge consecutively printed warnings into single dev_warn_ratelimited
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* include bridge and bridgeport API needed to isolate ports
* remove warning in .setup as ports are now isolated
* make ready-after-reset check more robust by adding delay
* sort structs in order of struct definitions
* best effort to sort functions without introducing additional prototypes
* always use enums with kerneldoc comments in mxl862xx-api.h
* remove bogus .phy_read and .phy_write DSA ops as the driver anyway registers a user MDIO bus with Clause-22 and Clause-45 operations
* various small style fixes
Changes since RFC v4
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* drop unused precompiler macros
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* fix indentation
4/4 net: dsa: add basic initial driver for MxL862xx switches
* output warning in .setup regarding unknown pre-configuration
* add comment explaining why CFGGET is used in reset function
Changes since RFC v3
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* remove labels from example
* remove 'bindings for' from commit title
2/4 net: dsa: add tag format for MxL862xx switches
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* unchanged
4/4 net: dsa: add basic initial driver for MxL862xx switches
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos and formatting improvements
Changes since RFC v2
1/4, 2/4, 3/4: unchanged
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing description in kerneldoc comment of
struct mxl862xx_ss_sp_tag
Changes since initial RFC
1/4 dt-bindings: net: dsa: add bindings for MaxLinear MxL862xx
* better description in dt-bindings doc
2/4 net: dsa: add tag formats for MxL862xx switches
* make sure all tag fields are initialized
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* new patch
4/4 net: dsa: add basic initial driver for MxL862xx switches
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* fix endian conversions
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID
Daniel Golle (4):
dt-bindings: net: dsa: add MaxLinear MxL862xx
net: dsa: add tag format for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add basic initial driver for MxL862xx switches
.../bindings/net/dsa/maxlinear,mxl862xx.yaml | 160 +++++ MAINTAINERS | 8 + drivers/net/dsa/Kconfig | 2 + drivers/net/dsa/Makefile | 1 + drivers/net/dsa/mxl862xx/Kconfig | 12 + drivers/net/dsa/mxl862xx/Makefile | 3 + drivers/net/dsa/mxl862xx/mxl862xx-api.h | 675 ++++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx-cmd.h | 49 ++ drivers/net/dsa/mxl862xx/mxl862xx-host.c | 245 +++++++ drivers/net/dsa/mxl862xx/mxl862xx-host.h | 12 + drivers/net/dsa/mxl862xx/mxl862xx.c | 483 +++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx.h | 16 + include/linux/mdio.h | 13 + include/net/dsa.h | 2 + net/dsa/Kconfig | 7 + net/dsa/Makefile | 1 + net/dsa/tag_mxl862xx.c | 110 +++ 17 files changed, 1799 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml create mode 100644 drivers/net/dsa/mxl862xx/Kconfig create mode 100644 drivers/net/dsa/mxl862xx/Makefile create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h create mode 100644 net/dsa/tag_mxl862xx.c
Signature · 1 line
2.52.0
Daniel Golle
maintainerPATCH v12 1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
Add documentation and an example for MaxLinear MxL86282 and MxL86252 switches.
---
v12: no changes
v11: no changes
v10: add microcontroller port 0
v9: no changes
v8: no changes
v7: no changes
v6: no changes
v5: no changes
RFC v4:
* remove labels from example
* remove 'bindings for' from commit title
RFC v3: no changes
RFC v2: better description in dt-bindings doc
--- .../bindings/net/dsa/maxlinear,mxl862xx.yaml | 160 ++++++++++++++++++ MAINTAINERS | 6 + 2 files changed, 166 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml new file +160 -0
@@ -0,0 +1,160 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/maxlinear,mxl862xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MaxLinear MxL862xx Ethernet Switch Family + +maintainers: + - Daniel Golle <[email protected]> + +description: + The MaxLinear MxL862xx switch family are multi-port Ethernet switches with + integrated 2.5GE PHYs. The MxL86252 has five PHY ports and the MxL86282 + has eight PHY ports. Both models come with two 10 Gigabit/s SerDes + interfaces to be used to connect external PHYs or SFP cages, or as CPU + port. + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +properties: + compatible: + enum: + - maxlinear,mxl86252 + - maxlinear,mxl86282 + + reg: + maxItems: 1 + description: MDIO address of the switch + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "maxlinear,mxl86282"; + reg = <0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Microcontroller port */ + port@0 { + reg = <0>; + status = "disabled"; + }; + + port@1 { + reg = <1>; + phy-handle = <&phy0>; + phy-mode = "internal"; + }; + + port@2 { + reg = <2>; + phy-handle = <&phy1>; + phy-mode = "internal"; + }; + + port@3 { + reg = <3>; + phy-handle = <&phy2>; + phy-mode = "internal"; + }; + + port@4 { + reg = <4>; + phy-handle = <&phy3>; + phy-mode = "internal"; + }; + + port@5 { + reg = <5>; + phy-handle = <&phy4>; + phy-mode = "internal"; + }; + + port@6 { + reg = <6>; + phy-handle = <&phy5>; + phy-mode = "internal"; + }; + + port@7 { + reg = <7>; + phy-handle = <&phy6>; + phy-mode = "internal"; + }; + + port@8 { + reg = <8>; + phy-handle = <&phy7>; + phy-mode = "internal"; + }; + + port@9 { + reg = <9>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "usxgmii"; + + fixed-link { + speed = <10000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + + phy3: ethernet-phy@3 { + reg = <3>; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + + phy6: ethernet-phy@6 { + reg = <6>; + }; + + phy7: ethernet-phy@7 { + reg = <7>; + }; + }; + }; + };
MAINTAINERS +6 -0
@@ -15619,6 +15619,12 @@ S: Supported F: drivers/net/phy/mxl-86110.c F: drivers/net/phy/mxl-gpy.c +MAXLINEAR MXL862XX SWITCH DRIVER +M: Daniel Golle <[email protected]> +L: [email protected] +S: Maintained +F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml + MCAN DEVICE DRIVER M: Markus Schneider-Pargmann <[email protected]> L: [email protected]
Signature · 1 line
2.52.0
Daniel Golle
maintainerPATCH v12 2/4 net: dsa: add tag format for MxL862xx switches
In reply to Daniel GolleAdd proprietary special tag format for the MaxLinear MXL862xx family of switches. While using the same Ethertype as MaxLinear's GSW1xx switches, the actual tag format differs significantly, hence we need a dedicated tag driver for that.
---
v12: no changes
v11:
* arrange local variables in reverse xmas tree order (again)
* use MXL862_NAME as .name in struct dsa_device_ops
v10: count ports starting from 0
v9: no changes
v8: no changes
v7: no changes
v6:
* remove unnecessary check for skb != NULL
* merge consecutively printed warnings into single dev_warn_ratelimited
v5:
* remove unused macro definitions
RFC v4:
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order
RFC v3: no changes
RFC v2: make sure all tag fields are initialized
--- MAINTAINERS | 1 + include/net/dsa.h | 2 + net/dsa/Kconfig | 7 +++ net/dsa/Makefile | 1 + net/dsa/tag_mxl862xx.c | 110 +++++++++++++++++++++++++++++++++++++++++ 5 files changed, 121 insertions(+) create mode 100644 net/dsa/tag_mxl862xx.c
MAINTAINERS +1 -0
@@ -15624,6 +15624,7 @@ M: Daniel Golle <[email protected]> L: [email protected] S: Maintained F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml +F: net/dsa/tag_mxl862xx.c MCAN DEVICE DRIVER M: Markus Schneider-Pargmann <[email protected]>
include/net/dsa.h +2 -0
@@ -57,6 +57,7 @@ struct tc_action;#define DSA_TAG_PROTO_BRCM_LEGACY_FCS_VALUE 29#define DSA_TAG_PROTO_YT921X_VALUE 30#define DSA_TAG_PROTO_MXL_GSW1XX_VALUE 31 +#define DSA_TAG_PROTO_MXL862_VALUE 32enum dsa_tag_protocol {DSA_TAG_PROTO_NONE =DSA_TAG_PROTO_NONE_VALUE ,
@@ -91,6 +92,7 @@ enum dsa_tag_protocol {DSA_TAG_PROTO_VSC73XX_8021Q =DSA_TAG_PROTO_VSC73XX_8021Q_VALUE ,DSA_TAG_PROTO_YT921X =DSA_TAG_PROTO_YT921X_VALUE ,DSA_TAG_PROTO_MXL_GSW1XX =DSA_TAG_PROTO_MXL_GSW1XX_VALUE , + DSA_TAG_PROTO_MXL862 = DSA_TAG_PROTO_MXL862_VALUE, };struct dsa_switch ;
net/dsa/Kconfig +7 -0
@@ -104,6 +104,13 @@ config NET_DSA_TAG_MTK Say Y or M if you want to enable support for tagging frames for Mediatek switches. +config NET_DSA_TAG_MXL_862XX + tristate "Tag driver for MxL862xx switches" + help + Say Y or M if you want to enable support for tagging frames for the + Maxlinear MxL86252 and MxL86282 switches using their native 8-byte + tagging protocol. + config NET_DSA_TAG_MXL_GSW1XX tristate "Tag driver for MaxLinear GSW1xx switches" help
net/dsa/Makefile +1 -0
@@ -28,6 +28,7 @@ obj-$(CONFIG_NET_DSA_TAG_HELLCREEK) += tag_hellcreek.o obj-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o obj-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o obj-$(CONFIG_NET_DSA_TAG_MTK) += tag_mtk.o +obj-$(CONFIG_NET_DSA_TAG_MXL_862XX) += tag_mxl862xx.o obj-$(CONFIG_NET_DSA_TAG_MXL_GSW1XX) += tag_mxl-gsw1xx.o obj-$(CONFIG_NET_DSA_TAG_NONE) += tag_none.o obj-$(CONFIG_NET_DSA_TAG_OCELOT) += tag_ocelot.o
net/dsa/tag_mxl862xx.c new file +110 -0
110 lines not on this page · raw message
Signature · 1 line
2.52.0
Daniel Golle
maintainerPATCH v12 3/4 net: mdio: add unlocked mdiodev C45 bus accessors
In reply to Daniel GolleAdd helper inline functions __mdiodev_c45_read() and __mdiodev_c45_write(), which are the C45 equivalents of the existing __mdiodev_read() and __mdiodev_write() added by commit e6a45700e7e1 ("net: mdio: add unlocked mdiobus and mdiodev bus accessors")
---
v12: no changes
v11: no changes
v10: no changes
v9: no changes
v8: no changes
v7: no changes
v6: no changes
v5: fix indentation
RFC v4: no changes
RFC v3: no changes
RFC v2: add this patch, initial submission
--- include/linux/mdio.h | 13 +++++++++++++ 1 file changed, 13 insertions(+)
include/linux/mdio.h +13 -0
@@ -648,6 +648,19 @@ static inline int mdiodev_modify_changed(struct mdio_device *mdiodev, mask, set); } +static inline int __mdiodev_c45_read (struct mdio_device *mdiodev,int devad, +u16 regnum) +{ +return __mdiobus_c45_read (mdiodev->bus, mdiodev->addr, devad, regnum); +} + +static inline int __mdiodev_c45_write (struct mdio_device *mdiodev,u32 devad, +u16 regnum,u16 val) +{ +return __mdiobus_c45_write (mdiodev->bus, mdiodev->addr, devad, regnum, + val); +} +static inline int mdiodev_c45_modify (struct mdio_device *mdiodev,int devad,u32 regnum,u16 mask,u16 set) {
Signature · 1 line
2.52.0
Russell King (Oracle)
reviewerRe: [PATCH v12 3/4] net: mdio: add unlocked mdiodev C45 bus accessors
Quoted 6 lines · Daniel Golle
Add helper inline functions
__mdiodev_c45_read()and__mdiodev_c45_write(), which are the C45 equivalents of the existing__mdiodev_read()and__mdiodev_write()added by commite6a45700e7e1("net: mdio: add unlocked mdiobus and mdiodev bus accessors")Signed-off-by Daniel Golle <[email protected]>
Sigh, there's too many versions of this patch series. While netdev has a 24H period, there is also this - note the last sentence. The reason this exists is to stop this exact problem, where ongoing discussion is split across multiple different versions of the same series.
Resending after review
~~~~~~~~~~~~~~~~~~~~~~
Allow at least 24 hours to pass between postings. This will ensure reviewers from all geographical locations have a chance to chime in. Do not wait too long (weeks) between postings either as it will make it harder for reviewers to recall all the context.
Make sure you address all the feedback in your new posting. *Do not post a new version of the code if the discussion about the previous version is still ongoing, unless directly instructed by a reviewer.*
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Daniel Golle
maintainerPATCH v12 4/4 net: dsa: add basic initial driver for MxL862xx switches
In reply to Daniel GolleAdd very basic DSA driver for MaxLinear's MxL862xx switches.
In contrast to previous MaxLinear switches the MxL862xx has a built-in processor that runs a sophisticated firmware based on Zephyr RTOS. Interaction between the host and the switch hence is organized using a software API of that firmware rather than accessing hardware registers directly.
Add descriptions of the most basic firmware API calls to access the built-in MDIO bus hosting the 2.5GE PHYs, basic port control as well as setting up the CPU port.
Implement a very basic DSA driver using that API which is sufficient to get packets flowing between the user ports and the CPU port.
The firmware offers all features one would expect from a modern switch hardware, they are going to be added one by one in follow-up patch series.
---
v12:
* list switch variants in Kconfig starting with dash ('-')
* remove the __packed attribute on structs which are naturally packed according to C rules (ie. one other struct with only a single byte-aligned member)
* log error in mxl862xx_port_disable()
* introduce !NULL check for return value of dsa_to_port() in mxl862xx_add_single_port_bridge
* check cpu_dp being non-NULL before dereferencing dp->cpu_dp
* use non-racy and deterministic name for MII bus
* skip ports without cpu_dp assigned in mxl862xx_setup_cpu_bridge() to avoid potential NULL-pointer dereference
* call dev_set_drvdata() only after dsa_register_switch() has been successfully completed
v11:
* fix fatal last-second changes dsa_port_is_unused vs. dsa_is_unused_port and dsa_port_is_unused vs. dsa_is_unused_port
* use cpu_to_le16 in mxl862xx_configure_ctp_port
* improve formatting of some kerneldoc comments
v10:
* fix indentation in kernel-doc
* remove misleading comment regarding sub-interface IDs
* remove unused macros, set MXL862XX_MAX_PORTS to 17
* count ports starting from 0, 0 being the microcontroller
* improve port setup:
- split tag protocol and CTP port assignment
- use ports cpu_dp instead of relying on single (ie. first) CPU port
- handle CPU port like any other port
- prepare forward DT compatibility with multiple CPU ports
v9:
* remove practically unused struct hw_info
* lots of kerneldoc improvements in mxl862xx-api.h
* drop .mac_select_pcs() stub
* better handling for firmware error return value
* apply reverse xmas tree in mxl862xx_api_wrap
* guard headers with #ifdef macro
* include net/dsa.h and linux/mdio.h in mxl862xx.h
* call mxl862xx_port_fast_age() only once in .port_setup
* don't create isolation bridges for unused ports
* replace errornous cast with correct range of values denoting firmware errors
v8:
* use le32 endian in bridge_port_config API
* remove duplciate assignment of br_port_cfg.bridge_port_id when setting up CPU port
v7:
* fix kerneldoc style
v6:
* include bridge and bridgeport API needed to isolate ports
* remove warning in .setup as ports are now isolated
* make ready-after-reset check more robust by adding delay
* sort structs in order of struct definitions
* best effort to sort functions without introducing additional prototypes
* always use enums with kerneldoc comments in mxl862xx-api.h
* remove bogus .phy_read and .phy_write DSA ops as the driver anyway registers a user MDIO bus with Clause-22 and Clause-45 operations
* various small style fixes
v5:
* output warning in .setup regarding unknown pre-configuration
* add comment explaining why CFGGET is used in reset function
RFC v4:
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos
RFC v3:
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing descrition in kerneldoc comment of
struct mxl862xx_ss_sp_tag
RFC v2:
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID
--- MAINTAINERS | 1 + drivers/net/dsa/Kconfig | 2 + drivers/net/dsa/Makefile | 1 + drivers/net/dsa/mxl862xx/Kconfig | 12 + drivers/net/dsa/mxl862xx/Makefile | 3 + drivers/net/dsa/mxl862xx/mxl862xx-api.h | 675 +++++++++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx-cmd.h | 49 ++ drivers/net/dsa/mxl862xx/mxl862xx-host.c | 245 ++++++++ drivers/net/dsa/mxl862xx/mxl862xx-host.h | 12 + drivers/net/dsa/mxl862xx/mxl862xx.c | 483 ++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx.h | 16 + 11 files changed, 1499 insertions(+) create mode 100644 drivers/net/dsa/mxl862xx/Kconfig create mode 100644 drivers/net/dsa/mxl862xx/Makefile create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h
MAINTAINERS +1 -0
@@ -15624,6 +15624,7 @@ M: Daniel Golle <[email protected]> L: [email protected] S: Maintained F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml +F: drivers/net/dsa/mxl862xx/ F: net/dsa/tag_mxl862xx.c MCAN DEVICE DRIVER
drivers/net/dsa/Kconfig +2 -0
@@ -74,6 +74,8 @@ source "drivers/net/dsa/microchip/Kconfig" source "drivers/net/dsa/mv88e6xxx/Kconfig" +source "drivers/net/dsa/mxl862xx/Kconfig" + source "drivers/net/dsa/ocelot/Kconfig" source "drivers/net/dsa/qca/Kconfig"
drivers/net/dsa/Makefile +1 -0
@@ -20,6 +20,7 @@ obj-y += hirschmann/ obj-y += lantiq/ obj-y += microchip/ obj-y += mv88e6xxx/ +obj-y += mxl862xx/ obj-y += ocelot/ obj-y += qca/ obj-y += realtek/
drivers/net/dsa/mxl862xx/Kconfig new file +12 -0
@@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0-only +config NET_DSA_MXL862 + tristate "MaxLinear MxL862xx" + depends on NET_DSA + select MAXLINEAR_GPHY + select NET_DSA_TAG_MXL_862XX + help + This enables support for the MaxLinear MxL862xx switch family. + These switches have two 10GE SerDes interfaces, one typically + used as CPU port. + - MxL86282 has eight 2.5 Gigabit PHYs + - MxL86252 has five 2.5 Gigabit PHYs
drivers/net/dsa/mxl862xx/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 +obj-$(CONFIG_NET_DSA_MXL862) += mxl862xx_dsa.o +mxl862xx_dsa-y := mxl862xx.o mxl862xx-host.o
drivers/net/dsa/mxl862xx/mxl862xx-api.h new file +675 -0
675 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-cmd.h new file +49 -0
49 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-host.c new file +245 -0
245 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-host.h new file +12 -0
@@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __MXL862XX_HOST_H +#define __MXL862XX_HOST_H + +#include "mxl862xx.h" + +int mxl862xx_api_wrap (struct mxl862xx_priv *priv,u16 cmd,void *data,u16 size, +bool read,bool quiet); +int mxl862xx_reset (struct mxl862xx_priv *priv); + +#endif /* __MXL862XX_HOST_H */
drivers/net/dsa/mxl862xx/mxl862xx.c new file +483 -0
483 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx.h new file +16 -0
@@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __MXL862XX_H +#define __MXL862XX_H + +#include <linux/mdio.h> +#include <net/dsa.h> + +#define MXL862XX_MAX_PORTS 17 + +struct mxl862xx_priv { +struct dsa_switch *ds; +struct mdio_device *mdiodev; +}; + +#endif /* __MXL862XX_H */
Signature · 1 line
2.52.0
Vladimir Oltean
maintainerRe: [PATCH v12 4/4] net: dsa: add basic initial driver for MxL862xx switches
Quoted 20 lines · Daniel Golle
Add very basic DSA driver for MaxLinear's MxL862xx switches.
In contrast to previous MaxLinear switches the MxL862xx has a built-in processor that runs a sophisticated firmware based on Zephyr RTOS. Interaction between the host and the switch hence is organized using a software API of that firmware rather than accessing hardware registers directly.
Add descriptions of the most basic firmware API calls to access the built-in MDIO bus hosting the 2.5GE PHYs, basic port control as well as setting up the CPU port.
Implement a very basic DSA driver using that API which is sufficient to get packets flowing between the user ports and the CPU port.
The firmware offers all features one would expect from a modern switch hardware, they are going to be added one by one in follow-up patch series.
Signed-off-by Daniel Golle <[email protected]>
Quoted 15 lines
---
v12:
* list switch variants inKconfigstarting with dash ('-')
* remove the__packedattribute on structs which are naturally packed according to C rules (ie. one other struct with only a single byte-aligned member)
* log error inmxl862xx_port_disable()
* introduce !NULL check for return value ofdsa_to_port()inmxl862xx_add_single_port_bridge
* checkcpu_dpbeing non-NULL before dereferencingdp->cpu_dp
* use non-racy and deterministic name for MII bus
* skip ports withoutcpu_dpassigned inmxl862xx_setup_cpu_bridge()to avoid potential NULL-pointer dereference
* calldev_set_drvdata()only afterdsa_register_switch()has been successfully completed
I have nothing else to comment except to request you to undo some of the changes requested by AI review. Sorry I didn't have time to comment on v11.
drivers/net/dsa/mxl862xx/mxl862xx.c line 182
Quoted 9 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +9
-0+static int mxl862xx_add_single_port_bridge (struct dsa_switch *ds,int port) +{ +struct mxl862xx_bridge_port_config br_port_cfg = {}; +struct dsa_port *dp =dsa_to_port (ds, port); +struct mxl862xx_bridge_alloc br_alloc = {}; +int ret; + +if (!dp) +return -ENODEV ;
I'm sorry, I can't accept code that fears its own shadow. Some people, when they see a defensive NULL check think there is a valid reason behind it and will try to see what that reason is.
If dsa_to_port() would have possibly returned NULL, mxl862xx_port_setup() -> dsa_is_cpu_port(), which _is_ implemented using dsa_to_port(), would have already crashed the kernel and this test here would have been too little, too late.
But the kernel doesn't crash there, because calling dsa_to_port() is safe for these arguments, and this test is simply logically inconsistent with previous unconditional in this call path.
Quoted 38 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +38
-0+ + ret =MXL862XX_API_READ (ds->priv,MXL862XX_BRIDGE_ALLOC , br_alloc); +if (ret) { +dev_err (ds->dev,"failed to allocate a bridge for port %d\n" , port); +return ret; + } + + br_port_cfg.bridge_id = br_alloc.bridge_id; + br_port_cfg.bridge_port_id =cpu_to_le16 (port); + br_port_cfg.mask =cpu_to_le32 (MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_ID | +MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_PORT_MAP | +MXL862XX_BRIDGE_PORT_CONFIG_MASK_MC_SRC_MAC_LEARNING | +MXL862XX_BRIDGE_PORT_CONFIG_MASK_VLAN_BASED_MAC_LEARNING ); + br_port_cfg.src_mac_learning_disable = true; + br_port_cfg.vlan_src_mac_vid_enable = false; + br_port_cfg.vlan_dst_mac_vid_enable = false; +if (dp->cpu_dp) + br_port_cfg.bridge_port_map[0 ] =cpu_to_le16 (BIT (dp->cpu_dp->index)); + +return MXL862XX_API_WRITE (ds->priv,MXL862XX_BRIDGEPORT_CONFIGSET , br_port_cfg); +} + +static int mxl862xx_setup_mdio (struct dsa_switch *ds) +{ +struct mxl862xx_priv *priv = ds->priv; +struct device *dev = ds->dev; +struct device_node *mdio_np; +struct mii_bus *bus; +int ret; + + bus =devm_mdiobus_alloc (dev); +if (!bus) +return -ENOMEM ; + + bus->priv = priv; + ds->user_mii_bus = bus; + bus->name =KBUILD_MODNAME "-mii" ; +snprintf (bus->id,MII_BUS_ID_SIZE ,"%s-mii" ,dev_name (dev));
drivers/net/dsa/mxl862xx/mxl862xx.c line 230
Quoted 10 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +10
-0+ bus->read_c45 = mxl862xx_phy_read_c45_mii_bus; + bus->write_c45 = mxl862xx_phy_write_c45_mii_bus; + bus->read = mxl862xx_phy_read_mii_bus; + bus->write = mxl862xx_phy_write_mii_bus; + bus->parent = dev; + bus->phy_mask = ~ds->phys_mii_mask; + + mdio_np =of_get_child_by_name (dev->of_node,"mdio" ); +if (!mdio_np) +return -ENODEV ;
As per the dt-bindings patch, the "mdio" child node is not required. But here it is.
Quoted 57 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +57
-0+ + ret =devm_of_mdiobus_register (dev, bus, mdio_np); +of_node_put (mdio_np); + +return ret; +} + +static int mxl862xx_wait_ready (struct dsa_switch *ds) +{ +struct mxl862xx_sys_fw_image_version ver = {}; +unsigned long start = jiffies, timeout; +struct mxl862xx_priv *priv = ds->priv; +struct mxl862xx_cfg cfg = {}; +int ret; + + timeout = start +msecs_to_jiffies (MXL862XX_READY_TIMEOUT_MS ); +msleep (2000 );/* it always takes at least 2 seconds */ +do { + ret =MXL862XX_API_READ_QUIET (priv,SYS_MISC_FW_VERSION , ver); +if (ret || !ver.iv_major) + goto not_ready_yet; + +/* being able to perform CFGGET indicates that +* the firmware is ready +*/ + ret =MXL862XX_API_READ_QUIET (priv, +MXL862XX_COMMON_CFGGET , + cfg); +if (ret) + goto not_ready_yet; + +dev_info (ds->dev,"switch ready after %ums, firmware %u.%u.%u (build %u)\n" , +jiffies_to_msecs (jiffies - start), + ver.iv_major, ver.iv_minor, +le16_to_cpu (ver.iv_revision), +le32_to_cpu (ver.iv_build_num)); +return 0 ; + +not_ready_yet: +msleep (MXL862XX_READY_POLL_MS ); + }while (time_before (jiffies, timeout)); + +dev_err (ds->dev,"switch not responding after reset\n" ); +return -ETIMEDOUT ; +} + +static int mxl862xx_setup_cpu_bridge (struct dsa_switch *ds,int port) +{ +struct mxl862xx_bridge_port_config br_port_cfg = {}; +struct mxl862xx_priv *priv = ds->priv; +u16 bridge_port_map =0 ; +struct dsa_port *dp; + +/* CPU port bridge setup */ + br_port_cfg.mask =cpu_to_le32 (MXL862XX_BRIDGE_PORT_CONFIG_MASK_BRIDGE_PORT_MAP | +MXL862XX_BRIDGE_PORT_CONFIG_MASK_MC_SRC_MAC_LEARNING | +MXL862XX_BRIDGE_PORT_CONFIG_MASK_VLAN_BASED_MAC_LEARNING );
drivers/net/dsa/mxl862xx/mxl862xx.c line 297
Quoted 10 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +10
-0+ + br_port_cfg.bridge_port_id =cpu_to_le16 (port); + br_port_cfg.src_mac_learning_disable = false; + br_port_cfg.vlan_src_mac_vid_enable = true; + br_port_cfg.vlan_dst_mac_vid_enable = true; + +/* include all assigned user ports in the CPU portmap */ +dsa_switch_for_each_user_port (dp, ds) { +if (!dp->cpu_dp) +continue ;
All user ports are given a valid non-NULL dp->cpu_dp pointer. I strongly oppose introducing FUD in the code. If there are valid reasons behind this I'm all ears, but there aren't.
Quoted 33 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +33
-0+ +if (dp->cpu_dp->index != port) +continue ; + + bridge_port_map |=BIT (dp->index); + } + br_port_cfg.bridge_port_map[0 ] |=cpu_to_le16 (bridge_port_map); + +return MXL862XX_API_WRITE (priv,MXL862XX_BRIDGEPORT_CONFIGSET , br_port_cfg); +} + +static int mxl862xx_setup (struct dsa_switch *ds) +{ +struct mxl862xx_priv *priv = ds->priv; +int ret; + + ret =mxl862xx_reset (priv); +if (ret) +return ret; + + ret =mxl862xx_wait_ready (ds); +if (ret) +return ret; + +return mxl862xx_setup_mdio (ds); +} + +static int mxl862xx_port_setup (struct dsa_switch *ds,int port) +{ +bool is_cpu_port =dsa_is_cpu_port (ds, port); +int ret; + +/* disable port and flush MAC entries */
drivers/net/dsa/mxl862xx/mxl862xx.c line 340
Quoted 10 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +10
-0+ ret =mxl862xx_port_state (ds, port, false); +if (ret) +return ret; + +mxl862xx_port_fast_age (ds, port); + +/* skip setup for unused and DSA ports */ +if (dsa_is_unused_port (ds, port) || +dsa_is_dsa_port (ds, port)) +return 0 ;
Each of dsa_is_cpu_port(), dsa_is_unused_port(), dsa_is_dsa_port() are implemented using dsa_to_port(), and that loops over dst->ports in order to find "dp" just to return dp->index.
OTOH if you call dsa_to_port() only once, we have dsa_port_is_cpu(), dsa_port_is_unused(), dsa_port_is_dsa() which can be called on that and have lower complexity. Please do that.
You do _not_ need to test whether dsa_to_port() returns NULL, if "ds" and "port" were passed to you by DSA in the context of a DSA callback. Any exception to this rule will be explicitly noted in the documentation.
Quoted 86 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +86
-0+ +/* configure tag protocol */ + ret =mxl862xx_configure_sp_tag_proto (ds, port, is_cpu_port); +if (ret) +return ret; + +/* assign CTP port IDs */ + ret =mxl862xx_configure_ctp_port (ds, port, port, + is_cpu_port ?32 - port :1 ); +if (ret) +return ret; + +if (is_cpu_port) +/* assign user ports to CPU port bridge */ +return mxl862xx_setup_cpu_bridge (ds, port); + +/* setup single-port bridge for user ports */ +return mxl862xx_add_single_port_bridge (ds, port); +} + +static void mxl862xx_phylink_get_caps (struct dsa_switch *ds,int port, +struct phylink_config *config) +{ + config->mac_capabilities =MAC_ASYM_PAUSE |MAC_SYM_PAUSE |MAC_10 | +MAC_100 |MAC_1000 |MAC_2500FD ; + +__set_bit (PHY_INTERFACE_MODE_INTERNAL , + config->supported_interfaces); +} + +static const struct dsa_switch_ops mxl862xx_switch_ops = { + .get_tag_protocol = mxl862xx_get_tag_protocol, + .setup = mxl862xx_setup, + .port_setup = mxl862xx_port_setup, + .phylink_get_caps = mxl862xx_phylink_get_caps, + .port_enable = mxl862xx_port_enable, + .port_disable = mxl862xx_port_disable, + .port_fast_age = mxl862xx_port_fast_age, +}; + +static void mxl862xx_phylink_mac_config (struct phylink_config *config, +unsigned int mode, +const struct phylink_link_state *state) +{ +} + +static void mxl862xx_phylink_mac_link_down (struct phylink_config *config, +unsigned int mode, +phy_interface_t interface) +{ +} + +static void mxl862xx_phylink_mac_link_up (struct phylink_config *config, +struct phy_device *phydev, +unsigned int mode, +phy_interface_t interface, +int speed,int duplex, +bool tx_pause,bool rx_pause) +{ +} + +static const struct phylink_mac_ops mxl862xx_phylink_mac_ops = { + .mac_config = mxl862xx_phylink_mac_config, + .mac_link_down = mxl862xx_phylink_mac_link_down, + .mac_link_up = mxl862xx_phylink_mac_link_up, +}; + +static int mxl862xx_probe (struct mdio_device *mdiodev) +{ +struct device *dev = &mdiodev->dev; +struct mxl862xx_priv *priv; +struct dsa_switch *ds; +int ret; + + priv =devm_kzalloc (dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) +return -ENOMEM ; + + priv->mdiodev = mdiodev; + + ds =devm_kzalloc (dev,sizeof (*ds),GFP_KERNEL ); +if (!ds) +return -ENOMEM ; + + priv->ds = ds; + ds->dev = dev;
drivers/net/dsa/mxl862xx/mxl862xx.c line 436
Quoted 10 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +10
-0+ ds->priv = priv; + ds->ops = &mxl862xx_switch_ops; + ds->phylink_mac_ops = &mxl862xx_phylink_mac_ops; + ds->num_ports =MXL862XX_MAX_PORTS ; + + ret =dsa_register_switch (ds); +if (ret) +return ret; + +dev_set_drvdata (dev, ds);
There is no point in doing this, calling dev_set_drvdata() before and then simply "return dsa_register_switch()" is perfectly fine. You also won't need the "ret" variable.
Quoted 47 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +47
-0+ +return 0 ; +} + +static void mxl862xx_remove (struct mdio_device *mdiodev) +{ +struct dsa_switch *ds =dev_get_drvdata (&mdiodev->dev); + +if (!ds) +return ; + +dsa_unregister_switch (ds); +} + +static void mxl862xx_shutdown (struct mdio_device *mdiodev) +{ +struct dsa_switch *ds =dev_get_drvdata (&mdiodev->dev); + +if (!ds) +return ; + +dsa_switch_shutdown (ds); + +dev_set_drvdata (&mdiodev->dev,NULL ); +} + +static const struct of_device_id mxl862xx_of_match[] = { + { .compatible ="maxlinear,mxl86282" }, + { .compatible ="maxlinear,mxl86252" }, + {/* sentinel */ } +}; +MODULE_DEVICE_TABLE (of, mxl862xx_of_match); + +static struct mdio_driver mxl862xx_driver = { + .probe = mxl862xx_probe, + .remove = mxl862xx_remove, + .shutdown = mxl862xx_shutdown, + .mdiodrv.driver = { + .name ="mxl862xx" , + .of_match_table = mxl862xx_of_match, + }, +}; + +mdio_module_driver (mxl862xx_driver); + +MODULE_DESCRIPTION ("Driver for MaxLinear MxL862xx switch family" ); +MODULE_LICENSE ("GPL" );
Daniel Golle
maintainerRe: [PATCH v12 4/4] net: dsa: add basic initial driver for MxL862xx switches
Quoted 22 lines · Vladimir Oltean
Quoted 21 lines · Daniel Golle
drivers/net/dsa/mxl862xx/mxl862xx.c new file +21
-0+static int mxl862xx_setup_mdio (struct dsa_switch *ds) +{ +struct mxl862xx_priv *priv = ds->priv; +struct device *dev = ds->dev; +struct device_node *mdio_np; +struct mii_bus *bus; +int ret; + + bus =devm_mdiobus_alloc (dev); +if (!bus) +return -ENOMEM ; + + bus->priv = priv; + ds->user_mii_bus = bus; + bus->name =KBUILD_MODNAME "-mii" ; +snprintf (bus->id,MII_BUS_ID_SIZE ,"%s-mii" ,dev_name (dev)); + bus->read_c45 = mxl862xx_phy_read_c45_mii_bus; + bus->write_c45 = mxl862xx_phy_write_c45_mii_bus; + bus->read = mxl862xx_phy_read_mii_bus; + bus->write = mxl862xx_phy_write_mii_bus; + bus->parent = dev;
Quoted 8 lines
drivers/net/dsa/mxl862xx/mxl862xx.c line 230
Quoted 5 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +5
-0+ bus->phy_mask = ~ds->phys_mii_mask; + + mdio_np =of_get_child_by_name (dev->of_node,"mdio" ); +if (!mdio_np) +return -ENODEV ;As per the dt-bindings patch, the "mdio" child node is not required. But here it is.
Now that ports are counted from 0, and 0 being the microcontroller, the port number no longer matches the PHY ID, so I suppose I got to change the dt-bindigns as that kinda makes the mdio node mandatory for anything to work.
Quoted 5 lines
All user ports are given a valid non-NULL
dp->cpu_dppointer. I strongly oppose introducing FUD in the code. If there are valid reasons behind this I'm all ears, but there aren't.
Looking at other drivers I thought that, and regret not having challenged the AI commenting on this...