net: dsa: initial support for MaxLinear MxL862xx switches
Subsystems (6)
Daniel Golle
maintainerv14 cover net: dsa: initial support for MaxLinear MxL862xx switches
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
MxL862xx integrates a firmware running on an embedded processor (based on Zephyr RTOS). Host interaction uses a simple netlink-like API transported over MDIO/MMD.
This series includes only what's needed to pass traffic between user ports and the CPU port: relayed MDIO to internal PHYs, basic port enable/disable, and CPU-port special tagging.
The SerDes interface of the CPU port is automatically configured by the switch after reset using a board-specific configuration stored together with the firmware in the flash chip attached to the switch, so no action is needed from the driver to setup the interface mode of the CPU port.
Also MAC settings of the PHY ports are automatically configured, which means the driver works fine with phylink_mac_ops being all no-op stubs.
Multiple follow up series will bring support for setting up the other SerDes PCS interface (ie. not used for the CPU port), bridge, VLAN, ... offloading, and support for using an 802.1Q-based special tag instead of the proprietary 8-byte tag.
---
basic DSA selftests were run, results:
* no_forwarding.sh: all tests PASS
* bridge_vlan_unaware.sh: all tests PASS
* bridge_vlan_mcast.sh: all tests PASS
* bridge_vlan_aware.sh: all tests PASS
* local_termination.sh: all tests PASS or XFAIL, except for
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address [FAIL]
reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address, allmulti [FAIL]
reception succeeded, but should have failed
As obviously this is mostly testing the Linux software bridge at this point so I didn't bother to run any of the FDB or MDB related tests.
Some mystery about the relationship between the sub-interface ID and CTP port assignment remains for now, so I cannot yet fully explain the magic numbers when calculating the two.
(Why is it neccesary to allocate 23 CTPs when using port 9 as CPU port while there are at most 17 phyiscal interfaces in total, and only at most 13 when using one of the two SerDes as CPU interface? Why is there an offset of 16 when calculating the sub-interface ID? How will a total of 17 ports be possibly represented in a 4-bit field in the tag RX path?)
At this point this doesn't impact functionality, and I hope for further clarification discussing all that with MaxLinear engineers.
I believe the initial driver is anyway in good shape now, a follow-up series addressing configuring the SerDes interfaces will also have to take care of CTP assignment and sub-interfaces to not hit the mentioned 4-bit cap in the tag driver.
Changes since v13:
Address comments from Jakub Kicinski
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* Kconfig: fix Maxlinear -> MaxLinear, include vendor name in title
* add comment clarifying perspective of term "ingress"
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* selectively use __packed only for structs which aren't always naturally packed in mxl862xx-api.h, drop '#pragma pack(push, 1)'
* fix capitalisation Maxlinear -> MaxLinear
Changes since v12:
Address comments from Vladimir Oltean and add Reviewed-by:-tag given by Russell King (Oracle).
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* 'mdio' node is required
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* add Russell's Reviewed-by:-tag given for v11
4/4 net: dsa: add basic initial driver for MxL862xx switches
* use '#pragma pack(push, 1)' in mxl862xx-api.h
* relax timeout in mxl862xx_busy_wait() from 10000us to 500000us, this turned out to be needed when using the driver on older firmware
* reorder functions
* remove unneeded checks for dp or cpu_dp being !=NULL, add comments
Changes since v11:
Address comments reported by Jakub Kicinski using netdev-ai
https://patchwork.kernel.org/comment/26767905/
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* list switch variants in Kconfig starting with dash ('-')
* remove the __packed attribute on structs which are naturally packed according to C rules (ie. one other struct with only a single byte-aligned member)
* log error in mxl862xx_port_disable()
* introduce !NULL check for return value of dsa_to_port() in mxl862xx_add_single_port_bridge
* check cpu_dp being non-NULL before dereferencing dp->cpu_dp
* use non-racy and deterministic name for MII bus
* skip ports without cpu_dp assigned in mxl862xx_setup_cpu_bridge() to avoid potential NULL-pointer dereference
* call dev_set_drvdata() only after dsa_register_switch() has been successfully completed
Changes since v10:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* arrange local variables in reverse xmas tree order (again)
* use MXL862_NAME as .name in struct dsa_device_ops
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix fatal last-second changes dsa_port_is_unused vs. dsa_is_unused_port and dsa_port_is_unused vs. dsa_is_unused_port
* use cpu_to_le16 in mxl862xx_configure_ctp_port
* improve formatting of some kerneldoc comments
Changes since v9:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* add microcontroller port 0
2/4 net: dsa: add tag format for MxL862xx switches
* count ports starting from 0
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix indentation in kernel-doc
* remove misleading comment regarding sub-interface IDs
* remove unused macros, set MXL862XX_MAX_PORTS to 17
* count ports starting from 0, 0 being the microcontroller
* improve port setup:
- split tag protocol and CTP port assignment
- use ports cpu_dp instead of relying on single (ie. first) CPU port
- handle CPU port like any other port
- prepare forward DT compatibility with multiple CPU ports
Changes since v8:
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* remove practically unused struct hw_info
* lots of kerneldoc improvements in mxl862xx-api.h
* drop .mac_select_pcs() stub
* better handling for firmware error return value
* apply reverse xmas tree in mxl862xx_api_wrap
* guard headers with #ifdef macro
* include net/dsa.h and linux/mdio.h in mxl862xx.h
* call mxl862xx_port_fast_age() only once in .port_setup
* don't create isolation bridges for unused ports
* replace errornous cast with correct range of values denoting firmware errors
Changes since v7
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* use little-endian in bridge_port_config API
* remove duplciate assignment of br_port_cfg.bridge_port_id when setting up CPU port
Changes since v6
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* no changes
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix kerneldoc style
Changes since RFC v5
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* remove unnecessary check for skb != NULL
* merge consecutively printed warnings into single dev_warn_ratelimited
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* no changes
4/4 net: dsa: add basic initial driver for MxL862xx switches
* include bridge and bridgeport API needed to isolate ports
* remove warning in .setup as ports are now isolated
* make ready-after-reset check more robust by adding delay
* sort structs in order of struct definitions
* best effort to sort functions without introducing additional prototypes
* always use enums with kerneldoc comments in mxl862xx-api.h
* remove bogus .phy_read and .phy_write DSA ops as the driver anyway registers a user MDIO bus with Clause-22 and Clause-45 operations
* various small style fixes
Changes since RFC v4
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* no changes
2/4 net: dsa: add tag format for MxL862xx switches
* drop unused precompiler macros
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* fix indentation
4/4 net: dsa: add basic initial driver for MxL862xx switches
* output warning in .setup regarding unknown pre-configuration
* add comment explaining why CFGGET is used in reset function
Changes since RFC v3
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* remove labels from example
* remove 'bindings for' from commit title
2/4 net: dsa: add tag format for MxL862xx switches
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* unchanged
4/4 net: dsa: add basic initial driver for MxL862xx switches
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos and formatting improvements
Changes since RFC v2
1/4, 2/4, 3/4: unchanged
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing description in kerneldoc comment of
struct mxl862xx_ss_sp_tag
Changes since initial RFC
1/4 dt-bindings: net: dsa: add bindings for MaxLinear MxL862xx
* better description in dt-bindings doc
2/4 net: dsa: add tag formats for MxL862xx switches
* make sure all tag fields are initialized
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* new patch
4/4 net: dsa: add basic initial driver for MxL862xx switches
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* fix endian conversions
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID
Daniel Golle (4):
dt-bindings: net: dsa: add MaxLinear MxL862xx
net: dsa: add tag format for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add basic initial driver for MxL862xx switches
.../bindings/net/dsa/maxlinear,mxl862xx.yaml | 161 +++++ MAINTAINERS | 8 + drivers/net/dsa/Kconfig | 2 + drivers/net/dsa/Makefile | 1 + drivers/net/dsa/mxl862xx/Kconfig | 12 + drivers/net/dsa/mxl862xx/Makefile | 3 + drivers/net/dsa/mxl862xx/mxl862xx-api.h | 675 ++++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx-cmd.h | 49 ++ drivers/net/dsa/mxl862xx/mxl862xx-host.c | 245 +++++++ drivers/net/dsa/mxl862xx/mxl862xx-host.h | 12 + drivers/net/dsa/mxl862xx/mxl862xx.c | 476 ++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx.h | 16 + include/linux/mdio.h | 13 + include/net/dsa.h | 2 + net/dsa/Kconfig | 7 + net/dsa/Makefile | 1 + net/dsa/tag_mxl862xx.c | 110 +++ 17 files changed, 1793 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml create mode 100644 drivers/net/dsa/mxl862xx/Kconfig create mode 100644 drivers/net/dsa/mxl862xx/Makefile create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h create mode 100644 net/dsa/tag_mxl862xx.c
Signature · 1 line
2.52.0
Daniel Golle
maintainerPATCH v14 1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
Add documentation and an example for MaxLinear MxL86282 and MxL86252 switches.
---
v14: no changes
v13: 'mdio' node is required
v12: no changes
v11: no changes
v10: add microcontroller port 0
v9: no changes
v8: no changes
v7: no changes
v6: no changes
v5: no changes
RFC v4:
* remove labels from example
* remove 'bindings for' from commit title
RFC v3: no changes
RFC v2: better description in dt-bindings doc
--- .../bindings/net/dsa/maxlinear,mxl862xx.yaml | 161 ++++++++++++++++++ MAINTAINERS | 6 + 2 files changed, 167 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml new file +161 -0
@@ -0,0 +1,161 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/maxlinear,mxl862xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MaxLinear MxL862xx Ethernet Switch Family + +maintainers: + - Daniel Golle <[email protected]> + +description: + The MaxLinear MxL862xx switch family are multi-port Ethernet switches with + integrated 2.5GE PHYs. The MxL86252 has five PHY ports and the MxL86282 + has eight PHY ports. Both models come with two 10 Gigabit/s SerDes + interfaces to be used to connect external PHYs or SFP cages, or as CPU + port. + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +properties: + compatible: + enum: + - maxlinear,mxl86252 + - maxlinear,mxl86282 + + reg: + maxItems: 1 + description: MDIO address of the switch + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + +required: + - compatible + - mdio + - reg + +unevaluatedProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "maxlinear,mxl86282"; + reg = <0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* Microcontroller port */ + port@0 { + reg = <0>; + status = "disabled"; + }; + + port@1 { + reg = <1>; + phy-handle = <&phy0>; + phy-mode = "internal"; + }; + + port@2 { + reg = <2>; + phy-handle = <&phy1>; + phy-mode = "internal"; + }; + + port@3 { + reg = <3>; + phy-handle = <&phy2>; + phy-mode = "internal"; + }; + + port@4 { + reg = <4>; + phy-handle = <&phy3>; + phy-mode = "internal"; + }; + + port@5 { + reg = <5>; + phy-handle = <&phy4>; + phy-mode = "internal"; + }; + + port@6 { + reg = <6>; + phy-handle = <&phy5>; + phy-mode = "internal"; + }; + + port@7 { + reg = <7>; + phy-handle = <&phy6>; + phy-mode = "internal"; + }; + + port@8 { + reg = <8>; + phy-handle = <&phy7>; + phy-mode = "internal"; + }; + + port@9 { + reg = <9>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "usxgmii"; + + fixed-link { + speed = <10000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + + phy3: ethernet-phy@3 { + reg = <3>; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + + phy6: ethernet-phy@6 { + reg = <6>; + }; + + phy7: ethernet-phy@7 { + reg = <7>; + }; + }; + }; + };
MAINTAINERS +6 -0
@@ -15625,6 +15625,12 @@ S: Supported F: drivers/net/phy/mxl-86110.c F: drivers/net/phy/mxl-gpy.c +MAXLINEAR MXL862XX SWITCH DRIVER +M: Daniel Golle <[email protected]> +L: [email protected] +S: Maintained +F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml + MCAN DEVICE DRIVER M: Markus Schneider-Pargmann <[email protected]> L: [email protected]
Signature · 1 line
2.52.0
Vladimir Oltean
maintainerRe: [PATCH net-next v14 1/4] dt-bindings: net: dsa: add MaxLinear MxL862xx
Quoted 3 lines · Daniel Golle
RFC v4:
* remove labels from example
* remove 'bindings for' from commit title
...
Quoted 7 lines
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml new file +7
-0+examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 {
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml line 113
Quoted 10 lines
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml new file +10
-0+ compatible = "maxlinear,mxl86282"; + reg = <0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@9 { + reg = <9>; + label = "cpu";
Sorry, it's my fault really for not checking since v4 that you properly applied my feedback to "Please remove port labels from the example."
https://lore.kernel.org/netdev/20251216224317.maxhcdsuqqxnywmu@skbuf/
There was an effort a few years ago to remove label = "cpu" at least from dt-binding examples, if not from device trees as well, because the "label" property is defined and parsed only for user ports, which the CPU port is not. [ and even for user ports, it is discouraged except for distributions with a sub-par udev implementation (OpenWrt) ].
This line should go away.
Quoted 11 lines
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml new file +11
-0+ ethernet = <&gmac0>; + phy-mode = "usxgmii"; + + fixed-link { + speed = <10000>; + full-duplex; + }; + }; + }; + }; + };
Daniel Golle
maintainerPATCH v14 2/4 net: dsa: add tag format for MxL862xx switches
In reply to Daniel GolleAdd proprietary special tag format for the MaxLinear MXL862xx family of switches. While using the same Ethertype as MaxLinear's GSW1xx switches, the actual tag format differs significantly, hence we need a dedicated tag driver for that.
---
v14:
* Kconfig: fix Maxlinear -> MaxLinear, include vendor name in title
* add comment clarifying perspective of term "ingress"
v13: no changes
v12: no changes
v11:
* arrange local variables in reverse xmas tree order (again)
* use MXL862_NAME as .name in struct dsa_device_ops
v10: count ports starting from 0
v9: no changes
v8: no changes
v7: no changes
v6:
* remove unnecessary check for skb != NULL
* merge consecutively printed warnings into single dev_warn_ratelimited
v5:
* remove unused macro definitions
RFC v4:
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order
RFC v3: no changes
RFC v2: make sure all tag fields are initialized
--- MAINTAINERS | 1 + include/net/dsa.h | 2 + net/dsa/Kconfig | 7 +++ net/dsa/Makefile | 1 + net/dsa/tag_mxl862xx.c | 110 +++++++++++++++++++++++++++++++++++++++++ 5 files changed, 121 insertions(+) create mode 100644 net/dsa/tag_mxl862xx.c
MAINTAINERS +1 -0
@@ -15630,6 +15630,7 @@ M: Daniel Golle <[email protected]> L: [email protected] S: Maintained F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml +F: net/dsa/tag_mxl862xx.c MCAN DEVICE DRIVER M: Markus Schneider-Pargmann <[email protected]>
include/net/dsa.h +2 -0
@@ -57,6 +57,7 @@ struct tc_action;#define DSA_TAG_PROTO_BRCM_LEGACY_FCS_VALUE 29#define DSA_TAG_PROTO_YT921X_VALUE 30#define DSA_TAG_PROTO_MXL_GSW1XX_VALUE 31 +#define DSA_TAG_PROTO_MXL862_VALUE 32enum dsa_tag_protocol {DSA_TAG_PROTO_NONE =DSA_TAG_PROTO_NONE_VALUE ,
@@ -91,6 +92,7 @@ enum dsa_tag_protocol {DSA_TAG_PROTO_VSC73XX_8021Q =DSA_TAG_PROTO_VSC73XX_8021Q_VALUE ,DSA_TAG_PROTO_YT921X =DSA_TAG_PROTO_YT921X_VALUE ,DSA_TAG_PROTO_MXL_GSW1XX =DSA_TAG_PROTO_MXL_GSW1XX_VALUE , + DSA_TAG_PROTO_MXL862 = DSA_TAG_PROTO_MXL862_VALUE, };struct dsa_switch ;
net/dsa/Kconfig +7 -0
@@ -104,6 +104,13 @@ config NET_DSA_TAG_MTK Say Y or M if you want to enable support for tagging frames for Mediatek switches. +config NET_DSA_TAG_MXL_862XX + tristate "Tag driver for MaxLinear MxL862xx switches" + help + Say Y or M if you want to enable support for tagging frames for the + MaxLinear MxL86252 and MxL86282 switches using their native 8-byte + tagging protocol. + config NET_DSA_TAG_MXL_GSW1XX tristate "Tag driver for MaxLinear GSW1xx switches" help
net/dsa/Makefile +1 -0
@@ -28,6 +28,7 @@ obj-$(CONFIG_NET_DSA_TAG_HELLCREEK) += tag_hellcreek.o obj-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o obj-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o obj-$(CONFIG_NET_DSA_TAG_MTK) += tag_mtk.o +obj-$(CONFIG_NET_DSA_TAG_MXL_862XX) += tag_mxl862xx.o obj-$(CONFIG_NET_DSA_TAG_MXL_GSW1XX) += tag_mxl-gsw1xx.o obj-$(CONFIG_NET_DSA_TAG_NONE) += tag_none.o obj-$(CONFIG_NET_DSA_TAG_OCELOT) += tag_ocelot.o
net/dsa/tag_mxl862xx.c new file +110 -0
110 lines not on this page · raw message
Signature · 1 line
2.52.0
Daniel Golle
maintainerPATCH v14 3/4 net: mdio: add unlocked mdiodev C45 bus accessors
In reply to Daniel GolleAdd helper inline functions __mdiodev_c45_read() and __mdiodev_c45_write(), which are the C45 equivalents of the existing __mdiodev_read() and __mdiodev_write() added by commit e6a45700e7e1 ("net: mdio: add unlocked mdiobus and mdiodev bus accessors")
---
v14: no changes
v13: add Russell's Reviewed-by:-tag given for v11
v12: no changes
v11: no changes
v10: no changes
v9: no changes
v8: no changes
v7: no changes
v6: no changes
v5: fix indentation
RFC v4: no changes
RFC v3: no changes
RFC v2: add this patch, initial submission
--- include/linux/mdio.h | 13 +++++++++++++ 1 file changed, 13 insertions(+)
include/linux/mdio.h +13 -0
@@ -647,6 +647,19 @@ static inline int mdiodev_modify_changed(struct mdio_device *mdiodev, mask, set); } +static inline int __mdiodev_c45_read (struct mdio_device *mdiodev,int devad, +u16 regnum) +{ +return __mdiobus_c45_read (mdiodev->bus, mdiodev->addr, devad, regnum); +} + +static inline int __mdiodev_c45_write (struct mdio_device *mdiodev,u32 devad, +u16 regnum,u16 val) +{ +return __mdiobus_c45_write (mdiodev->bus, mdiodev->addr, devad, regnum, + val); +} +static inline int mdiodev_c45_modify (struct mdio_device *mdiodev,int devad,u32 regnum,u16 mask,u16 set) {
Signature · 1 line
2.52.0
Daniel Golle
maintainerPATCH v14 4/4 net: dsa: add basic initial driver for MxL862xx switches
In reply to Daniel GolleAdd very basic DSA driver for MaxLinear's MxL862xx switches.
In contrast to previous MaxLinear switches the MxL862xx has a built-in processor that runs a sophisticated firmware based on Zephyr RTOS. Interaction between the host and the switch hence is organized using a software API of that firmware rather than accessing hardware registers directly.
Add descriptions of the most basic firmware API calls to access the built-in MDIO bus hosting the 2.5GE PHYs, basic port control as well as setting up the CPU port.
Implement a very basic DSA driver using that API which is sufficient to get packets flowing between the user ports and the CPU port.
The firmware offers all features one would expect from a modern switch hardware, they are going to be added one by one in follow-up patch series.
---
v14:
* selectively use __packed only for structs which aren't always naturally packed in mxl862xx-api.h, drop '#pragma pack(push, 1)'
* fix capitalisation Maxlinear -> MaxLinear
v13:
* use '#pragma pack(push, 1)' in mxl862xx-api.h
* relax timeout in mxl862xx_busy_wait() from 10000us to 500000us, this turned out to be needed when using the driver on older firmware
* reorder functions
* remove unneeded checks for dp or cpu_do being !=NULL
v12:
* list switch variants in Kconfig starting with dash ('-')
* remove the __packed attribute on structs which are naturally packed according to C rules (ie. one other struct with only a single byte-aligned member)
* log error in mxl862xx_port_disable()
* introduce !NULL check for return value of dsa_to_port() in mxl862xx_add_single_port_bridge
* check cpu_dp being non-NULL before dereferencing dp->cpu_dp
* use non-racy and deterministic name for MII bus
* skip ports without cpu_dp assigned in mxl862xx_setup_cpu_bridge() to avoid potential NULL-pointer dereference
* call dev_set_drvdata() only after dsa_register_switch() has been successfully completed
v11:
* fix fatal last-second changes dsa_port_is_unused vs. dsa_is_unused_port and dsa_port_is_unused vs. dsa_is_unused_port
* use cpu_to_le16 in mxl862xx_configure_ctp_port
* improve formatting of some kerneldoc comments
v10:
* fix indentation in kernel-doc
* remove misleading comment regarding sub-interface IDs
* remove unused macros, set MXL862XX_MAX_PORTS to 17
* count ports starting from 0, 0 being the microcontroller
* improve port setup:
- split tag protocol and CTP port assignment
- use ports cpu_dp instead of relying on single (ie. first) CPU port
- handle CPU port like any other port
- prepare forward DT compatibility with multiple CPU ports
v9:
* remove practically unused struct hw_info
* lots of kerneldoc improvements in mxl862xx-api.h
* drop .mac_select_pcs() stub
* better handling for firmware error return value
* apply reverse xmas tree in mxl862xx_api_wrap
* guard headers with #ifdef macro
* include net/dsa.h and linux/mdio.h in mxl862xx.h
* call mxl862xx_port_fast_age() only once in .port_setup
* don't create isolation bridges for unused ports
* replace errornous cast with correct range of values denoting firmware errors
v8:
* use le32 endian in bridge_port_config API
* remove duplciate assignment of br_port_cfg.bridge_port_id when setting up CPU port
v7:
* fix kerneldoc style
v6:
* include bridge and bridgeport API needed to isolate ports
* remove warning in .setup as ports are now isolated
* make ready-after-reset check more robust by adding delay
* sort structs in order of struct definitions
* best effort to sort functions without introducing additional prototypes
* always use enums with kerneldoc comments in mxl862xx-api.h
* remove bogus .phy_read and .phy_write DSA ops as the driver anyway registers a user MDIO bus with Clause-22 and Clause-45 operations
* various small style fixes
v5:
* output warning in .setup regarding unknown pre-configuration
* add comment explaining why CFGGET is used in reset function
RFC v4:
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos
RFC v3:
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing descrition in kerneldoc comment of
struct mxl862xx_ss_sp_tag
RFC v2:
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID
--- MAINTAINERS | 1 + drivers/net/dsa/Kconfig | 2 + drivers/net/dsa/Makefile | 1 + drivers/net/dsa/mxl862xx/Kconfig | 12 + drivers/net/dsa/mxl862xx/Makefile | 3 + drivers/net/dsa/mxl862xx/mxl862xx-api.h | 675 +++++++++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx-cmd.h | 49 ++ drivers/net/dsa/mxl862xx/mxl862xx-host.c | 245 ++++++++ drivers/net/dsa/mxl862xx/mxl862xx-host.h | 12 + drivers/net/dsa/mxl862xx/mxl862xx.c | 476 ++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx.h | 16 + 11 files changed, 1492 insertions(+) create mode 100644 drivers/net/dsa/mxl862xx/Kconfig create mode 100644 drivers/net/dsa/mxl862xx/Makefile create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h
MAINTAINERS +1 -0
@@ -15630,6 +15630,7 @@ M: Daniel Golle <[email protected]> L: [email protected] S: Maintained F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml +F: drivers/net/dsa/mxl862xx/ F: net/dsa/tag_mxl862xx.c MCAN DEVICE DRIVER
drivers/net/dsa/Kconfig +2 -0
@@ -74,6 +74,8 @@ source "drivers/net/dsa/microchip/Kconfig" source "drivers/net/dsa/mv88e6xxx/Kconfig" +source "drivers/net/dsa/mxl862xx/Kconfig" + source "drivers/net/dsa/ocelot/Kconfig" source "drivers/net/dsa/qca/Kconfig"
drivers/net/dsa/Makefile +1 -0
@@ -20,6 +20,7 @@ obj-y += hirschmann/ obj-y += lantiq/ obj-y += microchip/ obj-y += mv88e6xxx/ +obj-y += mxl862xx/ obj-y += ocelot/ obj-y += qca/ obj-y += realtek/
drivers/net/dsa/mxl862xx/Kconfig new file +12 -0
@@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0-only +config NET_DSA_MXL862 + tristate "MaxLinear MxL862xx" + depends on NET_DSA + select MAXLINEAR_GPHY + select NET_DSA_TAG_MXL_862XX + help + This enables support for the MaxLinear MxL862xx switch family. + These switches have two 10GE SerDes interfaces, one typically + used as CPU port. + - MxL86282 has eight 2.5 Gigabit PHYs + - MxL86252 has five 2.5 Gigabit PHYs
drivers/net/dsa/mxl862xx/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 +obj-$(CONFIG_NET_DSA_MXL862) += mxl862xx_dsa.o +mxl862xx_dsa-y := mxl862xx.o mxl862xx-host.o
drivers/net/dsa/mxl862xx/mxl862xx-api.h new file +675 -0
675 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-cmd.h new file +49 -0
49 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-host.c new file +245 -0
245 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-host.h new file +12 -0
@@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __MXL862XX_HOST_H +#define __MXL862XX_HOST_H + +#include "mxl862xx.h" + +int mxl862xx_api_wrap (struct mxl862xx_priv *priv,u16 cmd,void *data,u16 size, +bool read,bool quiet); +int mxl862xx_reset (struct mxl862xx_priv *priv); + +#endif /* __MXL862XX_HOST_H */
drivers/net/dsa/mxl862xx/mxl862xx.c new file +476 -0
476 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx.h new file +16 -0
@@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __MXL862XX_H +#define __MXL862XX_H + +#include <linux/mdio.h> +#include <net/dsa.h> + +#define MXL862XX_MAX_PORTS 17 + +struct mxl862xx_priv { +struct dsa_switch *ds; +struct mdio_device *mdiodev; +}; + +#endif /* __MXL862XX_H */
Signature · 1 line
2.52.0
Vladimir Oltean
maintainerRe: [PATCH net-next v14 4/4] net: dsa: add basic initial driver for MxL862xx switches
Quoted 43 lines · Daniel Golle
drivers/net/dsa/mxl862xx/mxl862xx.c new file +43
-0+/* PHY access via firmware relay */ +static int mxl862xx_phy_read_mmd (struct mxl862xx_priv *priv,int port, +int devadd,int reg) +{ +struct mdio_relay_data param = { + .phy = port, + .mmd = devadd, + .reg =cpu_to_le16 (reg), + }; +int ret; + + ret =MXL862XX_API_READ (priv,INT_GPHY_READ , param); +if (ret) +return ret; + +return le16_to_cpu (param.data); +} + +static int mxl862xx_phy_write_mmd (struct mxl862xx_priv *priv,int port, +int devadd,int reg,u16 data) +{ +struct mdio_relay_data param = { + .phy = port, + .mmd = devadd, + .reg =cpu_to_le16 (reg), + .data =cpu_to_le16 (data), + }; + +return MXL862XX_API_WRITE (priv,INT_GPHY_WRITE , param); +} + +static int mxl862xx_phy_read_mii_bus (struct mii_bus *bus,int port,int regnum) +{ +return mxl862xx_phy_read_mmd (bus->priv, port,0 , regnum); +} + +static int mxl862xx_phy_write_mii_bus (struct mii_bus *bus,int port, +int regnum,u16 val) +{ +return mxl862xx_phy_write_mmd (bus->priv, port,0 , regnum, val); +} + +static int mxl862xx_phy_read_c45_mii_bus(struct mii_bus *bus, int port,
drivers/net/dsa/mxl862xx/mxl862xx.c line 98
Quoted 10 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +10
-0+ int devadd, int regnum) +{ +return mxl862xx_phy_read_mmd (bus->priv, port, devadd, regnum); +} + +static int mxl862xx_phy_write_c45_mii_bus (struct mii_bus *bus,int port, +int devadd,int regnum,u16 val) +{ +return mxl862xx_phy_write_mmd (bus->priv, port, devadd, regnum, val); +}
You took inspiration from the wrong place with the mii_bus ops prototypes, specifically with the "int port" argument.
The second argument does not hold the port, it holds the PHY address. I.e. in this case:
port@6 {
reg = <6>;
phy-handle = <&phy5>;
phy-mode = "internal";
};
phy5: ethernet-phy@5 {
reg = <5>;
};"int port" is 5, not 6.
Your source of inspiration are the prototypes of an mii_bus used as ds->user_mii_bus. We have a different set of requirements there, because ds->user_mii_bus exists for the case where the PHY is not described in the device tree, so the port index is given as argument and the user_mii_bus is responsible for internally translating the port index to a PHY address.
So while the use of "int port" as argument name for these operations is justifiable in some cases, it is not applicable to this driver, and will be a pitfall for anyone who has to modify or debug this code.
Daniel Golle
maintainerRe: [PATCH net-next v14 4/4] net: dsa: add basic initial driver for MxL862xx switches
Quoted 78 lines · Vladimir Oltean
Quoted 43 lines · Daniel Golle
drivers/net/dsa/mxl862xx/mxl862xx.c new file +43
-0+/* PHY access via firmware relay */ +static int mxl862xx_phy_read_mmd (struct mxl862xx_priv *priv,int port, +int devadd,int reg) +{ +struct mdio_relay_data param = { + .phy = port, + .mmd = devadd, + .reg =cpu_to_le16 (reg), + }; +int ret; + + ret =MXL862XX_API_READ (priv,INT_GPHY_READ , param); +if (ret) +return ret; + +return le16_to_cpu (param.data); +} + +static int mxl862xx_phy_write_mmd (struct mxl862xx_priv *priv,int port, +int devadd,int reg,u16 data) +{ +struct mdio_relay_data param = { + .phy = port, + .mmd = devadd, + .reg =cpu_to_le16 (reg), + .data =cpu_to_le16 (data), + }; + +return MXL862XX_API_WRITE (priv,INT_GPHY_WRITE , param); +} + +static int mxl862xx_phy_read_mii_bus (struct mii_bus *bus,int port,int regnum) +{ +return mxl862xx_phy_read_mmd (bus->priv, port,0 , regnum); +} + +static int mxl862xx_phy_write_mii_bus (struct mii_bus *bus,int port, +int regnum,u16 val) +{ +return mxl862xx_phy_write_mmd (bus->priv, port,0 , regnum, val); +} + +static int mxl862xx_phy_read_c45_mii_bus(struct mii_bus *bus, int port,drivers/net/dsa/mxl862xx/mxl862xx.c line 98
Quoted 10 lines
drivers/net/dsa/mxl862xx/mxl862xx.c new file +10
-0+ int devadd, int regnum) +{ +return mxl862xx_phy_read_mmd (bus->priv, port, devadd, regnum); +} + +static int mxl862xx_phy_write_c45_mii_bus (struct mii_bus *bus,int port, +int devadd,int regnum,u16 val) +{ +return mxl862xx_phy_write_mmd (bus->priv, port, devadd, regnum, val); +}You took inspiration from the wrong place with the
mii_busops prototypes, specifically with the "int port" argument.The second argument does not hold the port, it holds the PHY address. I.e. in this case:
port@6 { reg = <6>; phy-handle = <&phy5>; phy-mode = "internal"; }; phy5: ethernet-phy@5 { reg = <5>; };"int port" is 5, not 6.
Your source of inspiration are the prototypes of an
mii_busused asds->user_mii_bus. We have a different set of requirements there, becauseds->user_mii_busexists for the case where the PHY is not described in the device tree, so the port index is given as argument and theuser_mii_busis responsible for internally translating the port index to a PHY address.
Quoted 3 lines
So while the use of "int port" as argument name for these operations is justifiable in some cases, it is not applicable to this driver, and will be a pitfall for anyone who has to modify or debug this code.
Ack. While not completely correct from the beginning I should have addressed that and changed the parameter to 'int addr' when I started to count physical ports from 0 and no longer hide the microcontroller -- from that moment on the PHY address and the port address are no longer equal.
I will post a follow-up series to address this and also the removal of the 'label' property from the DT binding example once this has been merged. Both cases don't justify a "Fixes:"-tag though, but I'll just try to be fast, so both can still be applied before net-next closes.
Quoted 5 lines · Daniel Golle
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
For the entire set:
with some minor comments I'll leave in individual patches, which I'd like you to address.
I don't want to put anybody in a bad spot, but given what time it is, this set should get at least _some_ time in net-next before the upcoming net-next PR, to allow for some reaction time in case of some unexpected reports like from static analysis or similar. So it would be good, because of that, for the fixups as a result of my comments to be separate patches rather than a new version.
Paolo Abeni
maintainerQuoted 11 lines · Vladimir Oltean
Quoted 5 lines · Daniel Golle
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
For the entire set:
Reviewed-by Vladimir Oltean <[email protected]>
Quoted 7 lines
with some minor comments I'll leave in individual patches, which I'd like you to address.
I don't want to put anybody in a bad spot, but given what time it is, this set should get at least _some_ time in net-next before the upcoming net-next PR, to allow for some reaction time in case of some unexpected reports like from static analysis or similar.
As I'm wrapping-up the PR right now, and the series is not applied yet, I fear the above is not going to happen.
Since a driver is involved (as opposed to the core stack) and there will be the usual release cycle to address issues before the code lands in an official release, I tend to think this series should still be merged - unless someone voices strong and valid concerns _very soon_.
Thanks,
Paolo
So it would be good,
Quoted 2 lines
because of that, for the fixups as a result of my comments to be separate patches rather than a new version.
Vladimir Oltean
maintainerQuoted 23 lines · Paolo Abeni
Quoted 11 lines · Vladimir Oltean
Quoted 5 lines · Daniel Golle
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
For the entire set:
Reviewed-by Vladimir Oltean <[email protected]>Quoted 7 lines
with some minor comments I'll leave in individual patches, which I'd like you to address.
I don't want to put anybody in a bad spot, but given what time it is, this set should get at least _some_ time in net-next before the upcoming net-next PR, to allow for some reaction time in case of some unexpected reports like from static analysis or similar.
As I'm wrapping-up the PR right now, and the series is not applied yet, I fear the above is not going to happen.
Quoted 8 lines
Since a driver is involved (as opposed to the core stack) and there will be the usual release cycle to address issues before the code lands in an official release, I tend to think this series should still be merged - unless someone voices strong and valid concerns
_verysoon_.Thanks,
Paolo
My feedback is non-functional, so it likely won't be addressed in the RCs. Anyway, it's probably fine...
Daniel Golle
maintainerQuoted 28 lines · Paolo Abeni
Quoted 11 lines · Vladimir Oltean
Quoted 5 lines · Daniel Golle
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
For the entire set:
Reviewed-by Vladimir Oltean <[email protected]>Quoted 7 lines
with some minor comments I'll leave in individual patches, which I'd like you to address.
I don't want to put anybody in a bad spot, but given what time it is, this set should get at least _some_ time in net-next before the upcoming net-next PR, to allow for some reaction time in case of some unexpected reports like from static analysis or similar.
As I'm wrapping-up the PR right now, and the series is not applied yet, I fear the above is not going to happen.
Since a driver is involved (as opposed to the core stack) and there will be the usual release cycle to address issues before the code lands in an official release, I tend to think this series should still be merged - unless someone voices strong and valid concerns
_verysoon_.
Quoted 7 lines
Thanks,
Paolo
So it would be good,
Quoted 2 lines
because of that, for the fixups as a result of my comments to be separate patches rather than a new version.
Meaning I should send them *now*, despite net-next being closed already?
Paolo Abeni
maintainerQuoted 31 lines · Daniel Golle
Quoted 30 lines · Paolo Abeni
Quoted 11 lines · Vladimir Oltean
Quoted 5 lines · Daniel Golle
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
For the entire set:
Reviewed-by Vladimir Oltean <[email protected]>Quoted 7 lines
with some minor comments I'll leave in individual patches, which I'd like you to address.
I don't want to put anybody in a bad spot, but given what time it is, this set should get at least _some_ time in net-next before the upcoming net-next PR, to allow for some reaction time in case of some unexpected reports like from static analysis or similar.
As I'm wrapping-up the PR right now, and the series is not applied yet, I fear the above is not going to happen.
Since a driver is involved (as opposed to the core stack) and there will be the usual release cycle to address issues before the code lands in an official release, I tend to think this series should still be merged - unless someone voices strong and valid concerns
_verysoon_.Thanks,
Quoted 7 lines
Quoted 5 lines
Paolo
So it would be good,
Quoted 2 lines
because of that, for the fixups as a result of my comments to be separate patches rather than a new version.
Meaning I should send them *now*, despite net-next being closed already?
I'm sorry, I trimmed badly my reply leaving irrelevant and possibly confusing text at the bottom.
I mean that I intend to apply the series as-is.
Please follow-up after the merge-window as needed.
Thanks,
Paolo
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:
Hello:
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:
Quoted 11 lines · On Sat, 7 Feb 2026 03:06:48 +0000 you wrote:
This series adds very basic DSA support for the MaxLinear MxL86252 (5x 2500Base-T PHYs) and MxL86282 (8x 2500Base-T PHYs) switches. In addition to the 2.5G TP ports both switches also come with two SerDes interfaces which can be used either to connect external PHYs or SFP cages, or as CPU port when using the switch with this DSA driver.
MxL862xx integrates a firmware running on an embedded processor (based on Zephyr RTOS). Host interaction uses a simple netlink-like API transported over MDIO/MMD.
[...]
Here is the summary with links:
- [net-next,v14,1/4] dt-bindings: net: dsa: add MaxLinear MxL862xx
https://git.kernel.org/netdev/net-next/c/4ccc9851355f - [net-next,v14,2/4] net: dsa: add tag format for MxL862xx switches https://git.kernel.org/netdev/net-next/c/85ee98742902 - [net-next,v14,3/4] net: mdio: add unlocked mdiodev C45 bus accessors https://git.kernel.org/netdev/net-next/c/b405b26d8d27 - [net-next,v14,4/4] net: dsa: add basic initial driver for MxL862xx switches https://git.kernel.org/netdev/net-next/c/23794bec1cb6
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html