arm: mvebu: Add GPIO LEDs to Mirabox board
PATCH 1/1 arm: mvebu: Add GPIO LEDs to Mirabox board
Add the three external LED definitions to the device tree file on the Mirabox.
The Mirabox user guide calls out one as a power LED, and the other two are defined for WiFi, but as the current mwifiex drivers don't have LED support, we make them status LEDs.
These have been tested working by writing to the appropriate /sys/class/leds trigger.
--- arch/arm/boot/dts/armada-370-mirabox.dts | 37 ++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)
arch/arm/boot/dts/armada-370-mirabox.dts +37 -0
@@ -33,6 +33,43 @@ clock-frequency = <600000000>; status = "okay"; }; + + pinctrl { + pwr_led_pin: pwr-led-pin { + marvell,pins = "mpp63"; + marvell,function = "gpo"; + }; + + stat_led_pins: stat-led-pins { + marvell,pins = "mpp64", "mpp65"; + marvell,function = "gpio"; + }; + }; + + gpio_leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_led_pin &stat_led_pins>; + + green_pwr_led { + label = "mirabox:green:pwr"; + gpios = <&gpio1 31 1>; + linux,default-trigger = "heartbeat"; + }; + + blue_stat_led { + label = "mirabox:blue:stat"; + gpios = <&gpio2 0 1>; + linux,default-trigger = "cpu0"; + }; + + green_stat_led { + label = "mirabox:green:stat"; + gpios = <&gpio2 1 1>; + default-state = "off"; + }; + }; + mdio { phy0: ethernet-phy at 0 { reg = <0>;
Signature · 1 line
1.8.1.2
PATCH 1/1 arm: mvebu: Add GPIO LEDs to Mirabox board
Quoted 7 lines · Ryan Press
Add the three external LED definitions to the device tree file on the Mirabox.
The Mirabox user guide calls out one as a power LED, and the other two are defined for WiFi, but as the current mwifiex drivers don't have LED support, we make them status LEDs.
Quoted 7 lines
These have been tested working by writing to the appropriate
/sys/class/ledstrigger.Signed-off-by Ryan Press <[email protected]>---
arch/arm/boot/dts/armada-370-mirabox.dts| 37 ++++++++++++++++++++++++++++++++1 file changed, 37 insertions(+)
Cheers,
Neil
PATCH 1/1 arm: mvebu: Add GPIO LEDs to Mirabox board
Quoted 13 lines · Neil Greatorex
Quoted 10 lines · Ryan Press
Add the three external LED definitions to the device tree file on the Mirabox.
The Mirabox user guide calls out one as a power LED, and the other two are defined for WiFi, but as the current mwifiex drivers don't have LED support, we make them status LEDs.
These have been tested working by writing to the appropriate
/sys/class/ledstrigger.
Quoted 7 lines
Quoted 4 lines
Signed-off-by Ryan Press <[email protected]>---
arch/arm/boot/dts/armada-370-mirabox.dts| 37 ++++++++++++++++++++++++++++++++1 file changed, 37 insertions(+)Tested-by Neil Greatorex <[email protected]>
Signature · 3 lines
Ezequiel Garc?a, Free Electrons Embedded Linux, Kernel and Android Engineering http://free-electrons.com
Jason Cooper
AppliedPATCH 1/1 arm: mvebu: Add GPIO LEDs to Mirabox board
In reply to Ryan PressQuoted 7 lines · Ryan Press
Add the three external LED definitions to the device tree file on the Mirabox.
The Mirabox user guide calls out one as a power LED, and the other two are defined for WiFi, but as the current mwifiex drivers don't have LED support, we make them status LEDs.
Quoted 7 lines
These have been tested working by writing to the appropriate
/sys/class/ledstrigger.Signed-off-by Ryan Press <[email protected]>--- arch/arm/boot/dts/armada-370-mirabox.dts | 37 ++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)
Applied to mvebu/dt
thx,
Jason.