Skip to contentSkip to conversation

Add LVTS thermal architecture

PATCH Superseded [email protected] 8 participants 57 messages Jan 24, 2023 – Mar 9, 2023

Subsystems (3)

v11 of 14 Superseded Latest is v14 →

lore
Share & tools
lore
#0 lore raw

v11 cover Add LVTS thermal architecture

From: Balsam CHIHI <[email protected]>

The LVTS (Low Voltage Thermal Sensor) driver is capable of monitoring multiple hot points. For that, it contains 7 thermal control blocks dedicated to specific devices on the die. Each control block can handle up to 4 sensors.

The thermal controller supports several interrupts. One for the cold trip point, the hot trip point, the return to the normal trip point, and a specific programmable trip point to monitor the temperature dynamically.

The temperature measurement can be done in two ways, the immediate mode where the temperature read is instantaneous and the filtered mode where the controller uses, by configuration, an average of a set of values removing the minimum and the maximum.

Finally, it is composed of 2 finite-state machines responsible for the state of the temperature (cold, hot, hot 2 normal, hot hot), the triggering of the interrupts, and the monitoring of the temperature.

As requested, the thermal driver has been reworked to reduce the complexity of the code. At this time, the 4 little CPUs and the 4 big CPUs are supported by the thermal driver.They are described in a data structure and more devices can be added later. The calibration routine has been simplified also.

The series provide the following changes:
- Move the Mediatek drivers inside a dedicated folder as their number is increasing
- Add the DT bindings for the controller
- Add the efuse node for the mt8195
- The LVTS driver
- The thermal zones description in the DT

Changelog:
v11:
- Rebase on top of "thermal/linux-next" :
base=0d568e144ead70189e7f16066dcb155b78ff9266
- Remove unsupported SoC (mt8192) from dt-binding definition
- Fix coding style issues :
- Move litterals to define
- Add interrupt macros
- Remove wildcard : only mt8195 is supported for now

v10:
- Rebase on top of "thermal/linux-next" : thermal-v6.3-rc1
- Rework the LVTS driver
- Add the thermal trip temperature and cooling devices for the sensors supported by the driver

v9:
- Rebase on top of 6.0.0-rc1
- Fix coding style issues
- Fix commit titles and commit messages
- Update dt-bindings :
- Add "allOf:if:then:"
- Use mt8192 as example (instead of mt8195)
- Fix dt-binding errors
- Fix DTS errors

v8:
- Fix coding style issues
- Rebase on top of next-20220803
- Add multi-instance support :
- Rewrite DT-binding and DTS :
- Add DT-binding and DTS for LVTS_v4 (MT8192 and MT8195)
- One LVTS node for each HW Domain (AP and MCU)
- One SW Instance for each HW Domain
- Add a Kconfig sub-menu entry for LVTS and LVTS_v4 SoCs
- Replace platform_get_resource by platform_get_mem_or_io to get Base Address
- Replace platform_get_resource by platform_get_irq to get Interrupt Number
- Add "lvts_" prefix to functions and structs

v7:
- Fix coding style issues
- Rewrite dt bindings
- was not accurate
- Use mt8195 for example (instead of mt8192)
- Rename mt6873 to mt8192
- Remove clock name
- Rebased on top of to series:
- patchwork.kernel.org/project/linux-mediatek/list/?series=637849
- patchwork.kernel.org/project/linux-pm/list/?series=639386

v6:
- Remove temperature aggregation (it will be added in another series)
- Update the way to read the temperature (read one sensor instead of all)
- Add support of mt8195

v5:
- Use 'git mv' for the relocated file.

v4:
- Rebase to kernel-v5.13-rc1

v3:
- change the expression in the lvts_temp_to_raw to dev_s64.

v2:
- Rebase to kernel-5.11-rc1.
- sort headers
- remove initial value 0 of msr_raw in the lvts_temp_to_raw.
- disconstruct the api of lvts_read_tc_msr_raw.
- add the initial value max_temp = 0 and compare e.q. in the lvts_read_all_tc_temperature.
- add the return with an invalid number in the lvts_init.

Balsam CHIHI (6):
thermal/drivers/mediatek: Relocate driver to mediatek folder dt-bindings/thermal/mediatek: Add LVTS thermal controllers dt-binding
definition
arm64/dts/mt8195: Add efuse node to mt8195 thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver arm64/dts/mt8195: Add thermal zones and thermal nodes arm64/dts/mt8195: Add temperature mitigation threshold

 .../thermal/mediatek,lvts-thermal.yaml        |  107 ++
 arch/arm64/boot/dts/mediatek/mt8195.dtsi      |  272 ++++
 drivers/thermal/Kconfig                       |   14 +-
 drivers/thermal/Makefile                      |    2 +-
 drivers/thermal/mediatek/Kconfig              |   36 +
 drivers/thermal/mediatek/Makefile             |    2 +
 .../auxadc_thermal.c}                         |    2 +-
 drivers/thermal/mediatek/lvts_thermal.c       | 1261 +++++++++++++++++
 include/dt-bindings/thermal/mediatek-lvts.h   |   19 +
 9 files changed, 1703 insertions(+), 12 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 drivers/thermal/mediatek/Kconfig
 create mode 100644 drivers/thermal/mediatek/Makefile
 rename drivers/thermal/{mtk_thermal.c => mediatek/auxadc_thermal.c} (99%)
 create mode 100644 drivers/thermal/mediatek/lvts_thermal.c
 create mode 100644 include/dt-bindings/thermal/mediatek-lvts.h

base-commit: 0d568e144ead70189e7f16066dcb155b78ff9266

Signature · 1 line
2.34.1
#1 lore raw

PATCH v11 1/6 thermal/drivers/mediatek: Relocate driver to mediatek folder

From: Balsam CHIHI <[email protected]>

Add MediaTek proprietary folder to upstream more thermal zone and cooler drivers, relocate the original thermal controller driver to it, and rename it as "auxadc_thermal.c" to show its purpose more clearly.

---
 drivers/thermal/Kconfig                       | 14 ++++---------
 drivers/thermal/Makefile                      |  2 +-
 drivers/thermal/mediatek/Kconfig              | 21 +++++++++++++++++++
 drivers/thermal/mediatek/Makefile             |  1 +
 .../auxadc_thermal.c}                         |  2 +-
 5 files changed, 28 insertions(+), 12 deletions(-)
 create mode 100644 drivers/thermal/mediatek/Kconfig
 create mode 100644 drivers/thermal/mediatek/Makefile
 rename drivers/thermal/{mtk_thermal.c => mediatek/auxadc_thermal.c} (99%)
drivers/thermal/Kconfig +4 -10
index eaeb2b2ee6e9..4cd7ab707315 100644
@@ -416,16 +416,10 @@ config DA9062_THERMAL
 	  zone.
 	  Compatible with the DA9062 and DA9061 PMICs.
 
-config MTK_THERMAL
-	tristate "Temperature sensor driver for mediatek SoCs"
-	depends on ARCH_MEDIATEK || COMPILE_TEST
-	depends on HAS_IOMEM
-	depends on NVMEM || NVMEM=n
-	depends on RESET_CONTROLLER
-	default y
-	help
-	  Enable this option if you want to have support for thermal management
-	  controller present in Mediatek SoCs
+menu "Mediatek thermal drivers"
+depends on ARCH_MEDIATEK || COMPILE_TEST
+source "drivers/thermal/mediatek/Kconfig"
+endmenu
 
 config AMLOGIC_THERMAL
 	tristate "Amlogic Thermal Support"
drivers/thermal/Makefile +1 -1
index 60f0dfa9aae2..1c460d189bd7 100644
@@ -56,7 +56,7 @@ obj-y				+= st/
 obj-y				+= qcom/
 obj-y				+= tegra/
 obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
-obj-$(CONFIG_MTK_THERMAL)	+= mtk_thermal.o
+obj-y				+= mediatek/
 obj-$(CONFIG_GENERIC_ADC_THERMAL)	+= thermal-generic-adc.o
 obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
 obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
drivers/thermal/mediatek/Kconfig new file +21 -0
new file mode 100644
index 000000000000..7558a847d4e9
@@ -0,0 +1,21 @@
+config MTK_THERMAL
+	tristate "MediaTek thermal drivers"
+	depends on THERMAL_OF
+	help
+	  This is the option for MediaTek thermal software solutions.
+	  Please enable corresponding options to get temperature
+	  information from thermal sensors or turn on throttle
+	  mechaisms for thermal mitigation.
+
+if MTK_THERMAL
+
+config MTK_SOC_THERMAL
+	tristate "AUXADC temperature sensor driver for MediaTek SoCs"
+	depends on HAS_IOMEM
+	help
+	  Enable this option if you want to get SoC temperature
+	  information for MediaTek platforms.
+	  This driver configures thermal controllers to collect
+	  temperature via AUXADC interface.
+
+endif
drivers/thermal/mediatek/Makefile new file +1 -0
new file mode 100644
index 000000000000..53e86e30b26f
@@ -0,0 +1 @@
+obj-$(CONFIG_MTK_SOC_THERMAL)	+= auxadc_thermal.o
drivers/thermal/mediatek/auxadc_thermal.c renamed from drivers/thermal/mtk_thermal.c +1 -1
similarity index 99%
rename from drivers/thermal/mtk_thermal.c
rename to drivers/thermal/mediatek/auxadc_thermal.c
index 9a8b107900e9..90ae6b5c530e 100644
@@ -23,7 +23,7 @@
 #include <linux/reset.h>
 #include <linux/types.h>
 
-#include "thermal_hwmon.h"
+#include "../thermal_hwmon.h"
 
 /* AUXADC Registers */
 #define AUXADC_CON1_SET_V	0x008
Signature · 1 line
2.34.1
maintainer Reviewed-by on v11 1/6
#2 lore raw

Re: [PATCH v11 1/6] thermal/drivers/mediatek: Relocate driver to mediatek folder

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 7 lines

From: Balsam CHIHI <[email protected]>

Add MediaTek proprietary folder to upstream more thermal zone and cooler drivers, relocate the original thermal controller driver to it, and rename it as "auxadc_thermal.c" to show its purpose more clearly.

#3 lore raw

Re: [PATCH v11 1/6] thermal/drivers/mediatek: Relocate driver to mediatek folder

Quoted 10 lines · AngeloGioacchino Del Regno

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 7 lines

From: Balsam CHIHI <[email protected]>

Add MediaTek proprietary folder to upstream more thermal zone and cooler drivers, relocate the original thermal controller driver to it, and rename it as "auxadc_thermal.c" to show its purpose more clearly.

Hi Angelo,

Thank you.

Best regards,
Balsam

Quoted 3 lines
#4 lore raw

PATCH v11 2/6 dt-bindings/thermal/mediatek: Add LVTS thermal controllers dt-binding definition

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

---
 .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
 include/dt-bindings/thermal/mediatek-lvts.h   |  19 ++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 include/dt-bindings/thermal/mediatek-lvts.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +107 -0
new file mode 100644
index 000000000000..12bfbdd8ff89
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description: LVTS reset for clearing temporary data on AP/MCU.
+
+  nvmem-cells:
+    minItems: 1
+    items:
+      - description: Calibration eFuse data 1 for LVTS
+      - description: Calibration eFuse data 2 for LVTS
+
+  nvmem-cell-names:
+    minItems: 1
+    items:
+      - const: lvts-calib-data-1
+      - const: lvts-calib-data-2
+
+  "#thermal-sensor-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - resets
+  - nvmem-cells
+  - nvmem-cell-names
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8195-clk.h>
+    #include <dt-bindings/reset/mt8195-resets.h>
+    #include <dt-bindings/thermal/mediatek-lvts.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      lvts_mcu: thermal-sensor@11278000 {
+        compatible = "mediatek,mt8195-lvts-mcu";
+        reg = <0 0x11278000 0 0x1000>;
+        interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+        resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+        nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+        nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+        #thermal-sensor-cells = <1>;
+      };
+    };
+
+    thermal_zones: thermal-zones {
+      cpu0-thermal {
+        polling-delay = <1000>;
+        polling-delay-passive = <250>;
+        thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
+        trips {
+          cpu0_alert: trip-alert {
+            temperature = <85000>;
+            hysteresis = <2000>;
+            type = "passive";
+          };
+
+          cpu0_crit: trip-crit {
+            temperature = <100000>;
+            hysteresis = <2000>;
+            type = "critical";
+          };
+        };
+      };
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +19 -0
new file mode 100644
index 000000000000..428a95c18509
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */
+
+#ifndef __MEDIATEK_LVTS_DT_H
+#define __MEDIATEK_LVTS_DT_H
+
+#define MT8195_MCU_BIG_CPU0	0
+#define MT8195_MCU_BIG_CPU1	1
+#define MT8195_MCU_BIG_CPU2	2
+#define MT8195_MCU_BIG_CPU3	3
+#define MT8195_MCU_LITTLE_CPU0	4
+#define MT8195_MCU_LITTLE_CPU1	5
+#define MT8195_MCU_LITTLE_CPU2	6
+#define MT8195_MCU_LITTLE_CPU3	7
+
+#endif /* __MEDIATEK_LVTS_DT_H */
Signature · 1 line
2.34.1
#5 lore raw

Re: [PATCH v11 2/6] dt-bindings/thermal/mediatek: Add LVTS thermal controllers dt-binding definition

Quoted 6 lines · On 24/01/2023 14:17, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

---

Krzysztof, Rob,

are you ok with these changes ?

Quoted 144 lines
  .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
  include/dt-bindings/thermal/mediatek-lvts.h   |  19 ++++
  2 files changed, 126 insertions(+)

create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml create mode 100644 include/dt-bindings/thermal/mediatek-lvts.h

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +107 -0
new file mode 100644
index 000000000000..12bfbdd8ff89
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description: LVTS reset for clearing temporary data on AP/MCU.
+
+  nvmem-cells:
+    minItems: 1
+    items:
+      - description: Calibration eFuse data 1 for LVTS
+      - description: Calibration eFuse data 2 for LVTS
+
+  nvmem-cell-names:
+    minItems: 1
+    items:
+      - const: lvts-calib-data-1
+      - const: lvts-calib-data-2
+
+  "#thermal-sensor-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - resets
+  - nvmem-cells
+  - nvmem-cell-names
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8195-clk.h>
+    #include <dt-bindings/reset/mt8195-resets.h>
+    #include <dt-bindings/thermal/mediatek-lvts.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      lvts_mcu: thermal-sensor@11278000 {
+        compatible = "mediatek,mt8195-lvts-mcu";
+        reg = <0 0x11278000 0 0x1000>;
+        interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+        resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+        nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+        nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+        #thermal-sensor-cells = <1>;
+      };
+    };
+
+    thermal_zones: thermal-zones {
+      cpu0-thermal {
+        polling-delay = <1000>;
+        polling-delay-passive = <250>;
+        thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
+        trips {
+          cpu0_alert: trip-alert {
+            temperature = <85000>;
+            hysteresis = <2000>;
+            type = "passive";
+          };
+
+          cpu0_crit: trip-crit {
+            temperature = <100000>;
+            hysteresis = <2000>;
+            type = "critical";
+          };
+        };
+      };
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +19 -0
new file mode 100644
index 000000000000..428a95c18509
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */
+
+#ifndef __MEDIATEK_LVTS_DT_H
+#define __MEDIATEK_LVTS_DT_H
+
+#define MT8195_MCU_BIG_CPU0	0
+#define MT8195_MCU_BIG_CPU1	1
+#define MT8195_MCU_BIG_CPU2	2
+#define MT8195_MCU_BIG_CPU3	3
+#define MT8195_MCU_LITTLE_CPU0	4
+#define MT8195_MCU_LITTLE_CPU1	5
+#define MT8195_MCU_LITTLE_CPU2	6
+#define MT8195_MCU_LITTLE_CPU3	7
+
+#endif /* __MEDIATEK_LVTS_DT_H */
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
maintainer
#6 lore raw

Re: [PATCH v11 2/6] dt-bindings/thermal/mediatek: Add LVTS thermal controllers dt-binding definition

Quoted 11 lines · Daniel Lezcano
Quoted 6 lines · On 24/01/2023 14:17, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

---

Krzysztof, Rob,

are you ok with these changes ?

It says v11, but I sure don't recall the 10 other versions...

Rob

#7 lore raw

Re: [PATCH v11 2/6] dt-bindings/thermal/mediatek: Add LVTS thermal controllers dt-binding definition

Quoted 6 lines · Rob Herring
Quoted 5 lines · Daniel Lezcano
Quoted 4 lines · On 24/01/2023 14:17, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Quoted 8 lines
Quoted 6 lines
Quoted 2 lines

---

Krzysztof, Rob,

are you ok with these changes ?

It says v11, but I sure don't recall the 10 other versions...

Ah, yes indeed. I remember Krzysztof told Balsam to fix the recipient list because some maintainers were missing.

Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
maintainer
#8 lore raw

Re: [PATCH v11 2/6] dt-bindings/thermal/mediatek: Add LVTS thermal controllers dt-binding definition

In reply to [email protected]
Quoted 2 lines · On Tue, Jan 24, 2023 at 02:17:13PM +0100, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

dt-bindings: thermal: ... for the subject

Quoted 129 lines

Add LVTS thermal controllers dt-binding definition for mt8195.

---
 .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
 include/dt-bindings/thermal/mediatek-lvts.h   |  19 ++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 include/dt-bindings/thermal/mediatek-lvts.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +107 -0
new file mode 100644
index 000000000000..12bfbdd8ff89
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description: LVTS reset for clearing temporary data on AP/MCU.
+
+  nvmem-cells:
+    minItems: 1
+    items:
+      - description: Calibration eFuse data 1 for LVTS
+      - description: Calibration eFuse data 2 for LVTS
+
+  nvmem-cell-names:
+    minItems: 1
+    items:
+      - const: lvts-calib-data-1
+      - const: lvts-calib-data-2
+
+  "#thermal-sensor-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - resets
+  - nvmem-cells
+  - nvmem-cell-names
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8195-clk.h>
+    #include <dt-bindings/reset/mt8195-resets.h>
+    #include <dt-bindings/thermal/mediatek-lvts.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      lvts_mcu: thermal-sensor@11278000 {
+        compatible = "mediatek,mt8195-lvts-mcu";
+        reg = <0 0x11278000 0 0x1000>;
+        interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+        resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+        nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+        nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+        #thermal-sensor-cells = <1>;
+      };
+    };
+
+    thermal_zones: thermal-zones {
+      cpu0-thermal {
+        polling-delay = <1000>;
+        polling-delay-passive = <250>;
+        thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
+        trips {
+          cpu0_alert: trip-alert {
+            temperature = <85000>;
+            hysteresis = <2000>;
+            type = "passive";
+          };
+
+          cpu0_crit: trip-crit {
+            temperature = <100000>;
+            hysteresis = <2000>;
+            type = "critical";
+          };
+        };
+      };
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..428a95c18509

include/dt-bindings/thermal/mediatek-lvts.h line 1

Quoted 1 line
include/dt-bindings/thermal/mediatek-lvts.h new file +1 -0
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0+ */

Okay with GPL 4? GPL-2.0-only

Dual license please. Consistent with your .dts files.

Quoted 21 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +18 -0
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */
+
+#ifndef __MEDIATEK_LVTS_DT_H
+#define __MEDIATEK_LVTS_DT_H
+
+#define MT8195_MCU_BIG_CPU0	0
+#define MT8195_MCU_BIG_CPU1	1
+#define MT8195_MCU_BIG_CPU2	2
+#define MT8195_MCU_BIG_CPU3	3
+#define MT8195_MCU_LITTLE_CPU0	4
+#define MT8195_MCU_LITTLE_CPU1	5
+#define MT8195_MCU_LITTLE_CPU2	6
+#define MT8195_MCU_LITTLE_CPU3	7
+
+#endif /* __MEDIATEK_LVTS_DT_H */
Signature · 1 line
2.34.1
#9 lore raw

Re: [PATCH v11 2/6] dt-bindings/thermal/mediatek: Add LVTS thermal controllers dt-binding definition

Hi Rob,

Quoted 6 lines · Rob Herring
Quoted 2 lines · On Tue, Jan 24, 2023 at 02:17:13PM +0100, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

dt-bindings: thermal: ... for the subject

I will fix it.

Quoted 134 lines
Quoted 130 lines

Add LVTS thermal controllers dt-binding definition for mt8195.

---
 .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
 include/dt-bindings/thermal/mediatek-lvts.h   |  19 ++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 include/dt-bindings/thermal/mediatek-lvts.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +107 -0
new file mode 100644
index 000000000000..12bfbdd8ff89
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description: LVTS reset for clearing temporary data on AP/MCU.
+
+  nvmem-cells:
+    minItems: 1
+    items:
+      - description: Calibration eFuse data 1 for LVTS
+      - description: Calibration eFuse data 2 for LVTS
+
+  nvmem-cell-names:
+    minItems: 1
+    items:
+      - const: lvts-calib-data-1
+      - const: lvts-calib-data-2
+
+  "#thermal-sensor-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - resets
+  - nvmem-cells
+  - nvmem-cell-names
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8195-clk.h>
+    #include <dt-bindings/reset/mt8195-resets.h>
+    #include <dt-bindings/thermal/mediatek-lvts.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      lvts_mcu: thermal-sensor@11278000 {
+        compatible = "mediatek,mt8195-lvts-mcu";
+        reg = <0 0x11278000 0 0x1000>;
+        interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+        resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+        nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+        nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+        #thermal-sensor-cells = <1>;
+      };
+    };
+
+    thermal_zones: thermal-zones {
+      cpu0-thermal {
+        polling-delay = <1000>;
+        polling-delay-passive = <250>;
+        thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
+        trips {
+          cpu0_alert: trip-alert {
+            temperature = <85000>;
+            hysteresis = <2000>;
+            type = "passive";
+          };
+
+          cpu0_crit: trip-crit {
+            temperature = <100000>;
+            hysteresis = <2000>;
+            type = "critical";
+          };
+        };
+      };
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..428a95c18509

include/dt-bindings/thermal/mediatek-lvts.h line 1

Quoted 1 line
include/dt-bindings/thermal/mediatek-lvts.h new file +1 -0
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0+ */

Okay with GPL 4? GPL-2.0-only

Quoted 1 line

Dual license please. Consistent with your .dts files.

I will fix this too.

Quoted 14 lines
Quoted 14 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +13 -0
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */
+
+#ifndef __MEDIATEK_LVTS_DT_H
+#define __MEDIATEK_LVTS_DT_H
+
+#define MT8195_MCU_BIG_CPU0  0
+#define MT8195_MCU_BIG_CPU1  1
+#define MT8195_MCU_BIG_CPU2  2
+#define MT8195_MCU_BIG_CPU3  3
+#define MT8195_MCU_LITTLE_CPU0       4
Quoted 8 lines
Quoted 8 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +5 -1
+#define MT8195_MCU_LITTLE_CPU1       5
+#define MT8195_MCU_LITTLE_CPU2       6
+#define MT8195_MCU_LITTLE_CPU3       7
+
+#endif /* __MEDIATEK_LVTS_DT_H */
--

2.34.1

Thank you for the review.

Best regards,
Balsam

#10 lore raw

PATCH v12 2/6 dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

---
Changelog:
v12:
- Fixed subject prefix
- Fixed licences GPL-2.0+ to GPL-2.0
- Added dual licenses
v11:
- Rebase on top of "thermal/linux-next" :
base=0d568e144ead70189e7f16066dcb155b78ff9266
- Remove unsupported SoC (mt8192) from dt-binding definition
v10:
- Rebase on top of "thermal/linux-next" : thermal-v6.3-rc1
v9:
- Rebase on top of 6.0.0-rc1
- Update dt-bindings :
- Add "allOf:if:then:"
- Use mt8192 as example (instead of mt8195)
- Fix dt-binding errors
- Fix DTS errors
v8:
- Fix coding style issues
- Rebase on top of next-20220803
- Add multi-instance support :
- Rewrite DT-binding and DTS :
- Add DT-binding and DTS for LVTS_v4 (MT8192 and MT8195)
- One LVTS node for each HW Domain (AP and MCU)
- One SW Instance for each HW Domain
v7:
- Fix coding style issues
- Rewrite dt bindings
- was not accurate
- Use mt8195 for example (instead of mt8192)
- Rename mt6873 to mt8192
- Remove clock name
---

---
 .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
 include/dt-bindings/thermal/mediatek-lvts.h   |  19 ++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 include/dt-bindings/thermal/mediatek-lvts.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +107 -0
new file mode 100644
index 000000000000..12bfbdd8ff89
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description: LVTS reset for clearing temporary data on AP/MCU.
+
+  nvmem-cells:
+    minItems: 1
+    items:
+      - description: Calibration eFuse data 1 for LVTS
+      - description: Calibration eFuse data 2 for LVTS
+
+  nvmem-cell-names:
+    minItems: 1
+    items:
+      - const: lvts-calib-data-1
+      - const: lvts-calib-data-2
+
+  "#thermal-sensor-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - resets
+  - nvmem-cells
+  - nvmem-cell-names
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8195-clk.h>
+    #include <dt-bindings/reset/mt8195-resets.h>
+    #include <dt-bindings/thermal/mediatek-lvts.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      lvts_mcu: thermal-sensor@11278000 {
+        compatible = "mediatek,mt8195-lvts-mcu";
+        reg = <0 0x11278000 0 0x1000>;
+        interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+        resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+        nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+        nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+        #thermal-sensor-cells = <1>;
+      };
+    };
+
+    thermal_zones: thermal-zones {
+      cpu0-thermal {
+        polling-delay = <1000>;
+        polling-delay-passive = <250>;
+        thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
+        trips {
+          cpu0_alert: trip-alert {
+            temperature = <85000>;
+            hysteresis = <2000>;
+            type = "passive";
+          };
+
+          cpu0_crit: trip-crit {
+            temperature = <100000>;
+            hysteresis = <2000>;
+            type = "critical";
+          };
+        };
+      };
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +19 -0
new file mode 100644
index 000000000000..902d5b1e4f43
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 or MIT) */
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */
+
+#ifndef __MEDIATEK_LVTS_DT_H
+#define __MEDIATEK_LVTS_DT_H
+
+#define MT8195_MCU_BIG_CPU0	0
+#define MT8195_MCU_BIG_CPU1	1
+#define MT8195_MCU_BIG_CPU2	2
+#define MT8195_MCU_BIG_CPU3	3
+#define MT8195_MCU_LITTLE_CPU0	4
+#define MT8195_MCU_LITTLE_CPU1	5
+#define MT8195_MCU_LITTLE_CPU2	6
+#define MT8195_MCU_LITTLE_CPU3	7
+
+#endif /* __MEDIATEK_LVTS_DT_H */
Signature · 1 line
2.34.1
#11 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Hi Rob,

I think Balsam took into account your comments. Is it fine for you ?

Quoted 185 lines · On 26/01/2023 17:10, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

---
Changelog:
v12:
- Fixed subject prefix
- Fixed licences GPL-2.0+ to GPL-2.0
- Added dual licenses
v11:
- Rebase on top of "thermal/linux-next" :
base=0d568e144ead70189e7f16066dcb155b78ff9266
- Remove unsupported SoC (mt8192) from dt-binding definition
v10:
- Rebase on top of "thermal/linux-next" : thermal-v6.3-rc1
v9:
- Rebase on top of 6.0.0-rc1
- Update dt-bindings :
- Add "allOf:if:then:"
- Use mt8192 as example (instead of mt8195)
- Fix dt-binding errors
- Fix DTS errors
v8:
- Fix coding style issues
- Rebase on top of next-20220803
- Add multi-instance support :
- Rewrite DT-binding and DTS :
- Add DT-binding and DTS for LVTS_v4 (MT8192 and MT8195)
- One LVTS node for each HW Domain (AP and MCU)
- One SW Instance for each HW Domain
v7:
- Fix coding style issues
- Rewrite dt bindings
- was not accurate
- Use mt8195 for example (instead of mt8192)
- Rename mt6873 to mt8192
- Remove clock name
---

---
  .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
  include/dt-bindings/thermal/mediatek-lvts.h   |  19 ++++
  2 files changed, 126 insertions(+)

create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml create mode 100644 include/dt-bindings/thermal/mediatek-lvts.h

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +107 -0
new file mode 100644
index 000000000000..12bfbdd8ff89
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description: LVTS reset for clearing temporary data on AP/MCU.
+
+  nvmem-cells:
+    minItems: 1
+    items:
+      - description: Calibration eFuse data 1 for LVTS
+      - description: Calibration eFuse data 2 for LVTS
+
+  nvmem-cell-names:
+    minItems: 1
+    items:
+      - const: lvts-calib-data-1
+      - const: lvts-calib-data-2
+
+  "#thermal-sensor-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - resets
+  - nvmem-cells
+  - nvmem-cell-names
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8195-clk.h>
+    #include <dt-bindings/reset/mt8195-resets.h>
+    #include <dt-bindings/thermal/mediatek-lvts.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      lvts_mcu: thermal-sensor@11278000 {
+        compatible = "mediatek,mt8195-lvts-mcu";
+        reg = <0 0x11278000 0 0x1000>;
+        interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+        resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+        nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+        nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+        #thermal-sensor-cells = <1>;
+      };
+    };
+
+    thermal_zones: thermal-zones {
+      cpu0-thermal {
+        polling-delay = <1000>;
+        polling-delay-passive = <250>;
+        thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
+        trips {
+          cpu0_alert: trip-alert {
+            temperature = <85000>;
+            hysteresis = <2000>;
+            type = "passive";
+          };
+
+          cpu0_crit: trip-crit {
+            temperature = <100000>;
+            hysteresis = <2000>;
+            type = "critical";
+          };
+        };
+      };
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +19 -0
new file mode 100644
index 000000000000..902d5b1e4f43
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 or MIT) */
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */
+
+#ifndef __MEDIATEK_LVTS_DT_H
+#define __MEDIATEK_LVTS_DT_H
+
+#define MT8195_MCU_BIG_CPU0	0
+#define MT8195_MCU_BIG_CPU1	1
+#define MT8195_MCU_BIG_CPU2	2
+#define MT8195_MCU_BIG_CPU3	3
+#define MT8195_MCU_LITTLE_CPU0	4
+#define MT8195_MCU_LITTLE_CPU1	5
+#define MT8195_MCU_LITTLE_CPU2	6
+#define MT8195_MCU_LITTLE_CPU3	7
+
+#endif /* __MEDIATEK_LVTS_DT_H */
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#12 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Quoted 5 lines · Daniel Lezcano

Hi Rob,

I think Balsam took into account your comments. Is it fine for you ?

The patchset was not sent to us at all, so it is the second version we see. Therefore it's not v12 for us. It's v2 and it still needs fixes.

I replied with minor comments (which could be fixed during applying) and the license concern (which you rather cannot change while applying).

Best regards,
Krzysztof

#13 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Hi Krzysztof,

Quoted 5 lines · Krzysztof Kozlowski
Quoted 3 lines · Daniel Lezcano

Hi Rob,

Quoted 8 lines
Quoted 2 lines

I think Balsam took into account your comments. Is it fine for you ?

The patchset was not sent to us at all, so it is the second version we see. Therefore it's not v12 for us. It's v2 and it still needs fixes.

I replied with minor comments (which could be fixed during applying) and the license concern (which you rather cannot change while applying).

I apologize for forgetting to add some email addresses while sending previous versions.
The changes you asked in your preview comment are taken in account and ready to be sent.
Please let me know what version number should the patch have.

Quoted 4 lines

Best regards,
Krzysztof

Best regards,
Balsam

#14 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

In reply to [email protected]
Quoted 3 lines · On 26/01/2023 17:10, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Subject: drop second/last, redundant "dt-binding definition". The "dt-bindings" prefix is already stating that these are bindings.

Plus two comments at the end.

include/dt-bindings/thermal/mediatek-lvts.h

Quoted 16 lines

---
Changelog:
v12:
- Fixed subject prefix
- Fixed licences GPL-2.0+ to GPL-2.0
- Added dual licenses

(quoted diff) +1 -0
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..902d5b1e4f43

Same filename as bindings.

include/dt-bindings/thermal/mediatek-lvts.h line 1

Quoted 2 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +1 -0
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 or MIT) */

Although this is correct, any reason why not using exactly the same license as bindings?

include/dt-bindings/thermal/mediatek-lvts.h line 5

Quoted 4 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +4 -0
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */

Best regards,
Krzysztof

#15 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Hi Krzysztof,

Thank you for the feedback.

Quoted 8 lines · Krzysztof Kozlowski
Quoted 3 lines · On 26/01/2023 17:10, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Subject: drop second/last, redundant "dt-binding definition". The "dt-bindings" prefix is already stating that these are bindings.

fixed.
The patch title has been fixed as you suggested :
"dt-bindings: thermal: mediatek: Add LVTS thermal controllers"

Quoted 13 lines

Plus two comments at the end.

Quoted 8 lines

---
Changelog:
v12:
- Fixed subject prefix
- Fixed licences GPL-2.0+ to GPL-2.0
- Added dual licenses

Quoted 8 lines

include/dt-bindings/thermal/mediatek-lvts.h

Quoted 6 lines
(quoted diff) +1 -0
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..902d5b1e4f43

Same filename as bindings.

fixed.
rename :
include/dt-bindings/thermal/mediatek-lvts.h => include/dt-bindings/thermal/mediatek-lvts-thermal.h

Quoted 6 lines

include/dt-bindings/thermal/mediatek-lvts.h line 1

Quoted 3 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +1 -0
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 or MIT) */

Although this is correct, any reason why not using exactly the same license as bindings?

fixed.
both files are now using the same license :
"SPDX-License-Identifier: (GPL-2.0 or MIT)"

Quoted 9 lines

include/dt-bindings/thermal/mediatek-lvts.h line 5

Quoted 5 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +4 -0
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */

Best regards,
Krzysztof

I'll send the changes soon.

Best regards,
Balsam

maintainer
#16 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Quoted 41 lines · Balsam CHIHI

Hi Krzysztof,

Thank you for the feedback.

Quoted 8 lines · Krzysztof Kozlowski
Quoted 3 lines · On 26/01/2023 17:10, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Subject: drop second/last, redundant "dt-binding definition". The "dt-bindings" prefix is already stating that these are bindings.

fixed.
The patch title has been fixed as you suggested :
"dt-bindings: thermal: mediatek: Add LVTS thermal controllers"

Quoted 13 lines

Plus two comments at the end.

Quoted 8 lines

---
Changelog:
v12:
- Fixed subject prefix
- Fixed licences GPL-2.0+ to GPL-2.0
- Added dual licenses

Quoted 8 lines

include/dt-bindings/thermal/mediatek-lvts.h

Quoted 6 lines
(quoted diff) +1 -0
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..902d5b1e4f43

Same filename as bindings.

Quoted 5 lines

fixed.
rename :
include/dt-bindings/thermal/mediatek-lvts.h => include/dt-bindings/thermal/mediatek-lvts-thermal.h

I think it should be include/dt-bindings/thermal/mediatek,lvts-thermal.yaml

Regards,
Matthias

Quoted 25 lines
Quoted 6 lines

include/dt-bindings/thermal/mediatek-lvts.h line 1

Quoted 3 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +1 -0
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 or MIT) */

Although this is correct, any reason why not using exactly the same license as bindings?

fixed.
both files are now using the same license :
"SPDX-License-Identifier: (GPL-2.0 or MIT)"

Quoted 9 lines

include/dt-bindings/thermal/mediatek-lvts.h line 5

Quoted 5 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +4 -0
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */

Best regards,
Krzysztof

I'll send the changes soon.

Best regards,
Balsam

#17 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Hi Matthias,

Quoted 45 lines · Matthias Brugger
Quoted 41 lines · Balsam CHIHI

Hi Krzysztof,

Thank you for the feedback.

Quoted 8 lines · Krzysztof Kozlowski
Quoted 3 lines · On 26/01/2023 17:10, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Subject: drop second/last, redundant "dt-binding definition". The "dt-bindings" prefix is already stating that these are bindings.

fixed.
The patch title has been fixed as you suggested :
"dt-bindings: thermal: mediatek: Add LVTS thermal controllers"

Quoted 21 lines

Plus two comments at the end.

include/dt-bindings/thermal/mediatek-lvts.h

Quoted 16 lines

---
Changelog:
v12:
- Fixed subject prefix
- Fixed licences GPL-2.0+ to GPL-2.0
- Added dual licenses

(quoted diff) +1 -0
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..902d5b1e4f43

Same filename as bindings.

Quoted 8 lines
Quoted 5 lines

fixed.
rename :
include/dt-bindings/thermal/mediatek-lvts.h => include/dt-bindings/thermal/mediatek-lvts-thermal.h

I think it should be include/dt-bindings/thermal/mediatek,lvts-thermal.yaml

OK,
I will change it like that.
(".h" and not ".yaml" I believe (just to be sure).).

Quoted 29 lines

Regards,
Matthias

Quoted 25 lines
Quoted 6 lines

include/dt-bindings/thermal/mediatek-lvts.h line 1

Quoted 3 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +1 -0
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 or MIT) */

Although this is correct, any reason why not using exactly the same license as bindings?

fixed.
both files are now using the same license :
"SPDX-License-Identifier: (GPL-2.0 or MIT)"

Quoted 9 lines

include/dt-bindings/thermal/mediatek-lvts.h line 5

Quoted 5 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +4 -0
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */

Best regards,
Krzysztof

I'll send the changes soon.

Best regards,
Balsam

Best regards,
Balsam

maintainer
#18 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Quoted 55 lines · Balsam CHIHI

Hi Matthias,

Quoted 51 lines · Matthias Brugger
Quoted 46 lines · Balsam CHIHI

Hi Krzysztof,

Thank you for the feedback.

Quoted 8 lines · Krzysztof Kozlowski
Quoted 3 lines · On 26/01/2023 17:10, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Subject: drop second/last, redundant "dt-binding definition". The "dt-bindings" prefix is already stating that these are bindings.

fixed.
The patch title has been fixed as you suggested :
"dt-bindings: thermal: mediatek: Add LVTS thermal controllers"

Quoted 13 lines

Plus two comments at the end.

Quoted 8 lines

---
Changelog:
v12:
- Fixed subject prefix
- Fixed licences GPL-2.0+ to GPL-2.0
- Added dual licenses

Quoted 8 lines

include/dt-bindings/thermal/mediatek-lvts.h

Quoted 6 lines
(quoted diff) +1 -0
+    };
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..902d5b1e4f43

Same filename as bindings.

fixed.
rename :
include/dt-bindings/thermal/mediatek-lvts.h => include/dt-bindings/thermal/mediatek-lvts-thermal.h

Quoted 7 lines
Quoted 2 lines

I think it should be include/dt-bindings/thermal/mediatek,lvts-thermal.yaml

OK,
I will change it like that.
(".h" and not ".yaml" I believe (just to be sure).).

Yes sure, .h. Sorry for the confusion.

Regards,
Matthias

Quoted 32 lines
Quoted 29 lines

Regards,
Matthias

Quoted 25 lines
Quoted 6 lines

include/dt-bindings/thermal/mediatek-lvts.h line 1

Quoted 3 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +1 -0
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 or MIT) */

Although this is correct, any reason why not using exactly the same license as bindings?

fixed.
both files are now using the same license :
"SPDX-License-Identifier: (GPL-2.0 or MIT)"

Quoted 9 lines

include/dt-bindings/thermal/mediatek-lvts.h line 5

Quoted 5 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +4 -0
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */

Best regards,
Krzysztof

I'll send the changes soon.

Best regards,
Balsam

Best regards,
Balsam

#19 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

In reply to Balsam CHIHI
Quoted 8 lines · Balsam CHIHI
Quoted 7 lines

include/dt-bindings/thermal/mediatek-lvts.h

Quoted 5 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..902d5b1e4f43

Same filename as bindings.

Quoted 4 lines

fixed.
rename :
include/dt-bindings/thermal/mediatek-lvts.h => include/dt-bindings/thermal/mediatek-lvts-thermal.h

Missing coma, so mediatek,lvts-thermal.h

Best regards,
Krzysztof

#20 lore raw

Re: [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers dt-binding definition

Quoted 9 lines · Krzysztof Kozlowski
Quoted 8 lines · Balsam CHIHI
Quoted 7 lines

include/dt-bindings/thermal/mediatek-lvts.h

Quoted 5 lines
include/dt-bindings/thermal/mediatek-lvts.h new file +0 -0
new file mode 100644
index 000000000000..902d5b1e4f43

Same filename as bindings.

Quoted 6 lines
Quoted 4 lines

fixed.
rename :
include/dt-bindings/thermal/mediatek-lvts.h => include/dt-bindings/thermal/mediatek-lvts-thermal.h

Missing coma, so mediatek,lvts-thermal.h

Yeah, actually Balsam resent a new version but numbered v3 taking into account your comments.

The versioning is becoming a bit messy now but if you are ok with the changes I'll pick the patch as is so we can go forward for this series.

Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#21 lore raw

PATCH v3 1/1 dt-bindings: thermal: mediatek: Add LVTS thermal controllers

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

---
Changelog:
v3:
- Fixed subject prefix
- Fixed licenses GPL-2.0-only OR BSD-2-Clause to GPL-2.0 OR MIT (to match DT)
- Fixed matching dt-binding file names
v2:
- Fixed subject prefix
- Fixed licenses GPL-2.0+ to GPL-2.0
- Added dual licenses
---

---
 .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
 .../thermal/mediatek,lvts-thermal.h           |  19 ++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 include/dt-bindings/thermal/mediatek,lvts-thermal.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +107 -0
new file mode 100644
index 000000000000..5fa5c7a1a417
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0 OR MIT)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+    description: LVTS reset for clearing temporary data on AP/MCU.
+
+  nvmem-cells:
+    minItems: 1
+    items:
+      - description: Calibration eFuse data 1 for LVTS
+      - description: Calibration eFuse data 2 for LVTS
+
+  nvmem-cell-names:
+    minItems: 1
+    items:
+      - const: lvts-calib-data-1
+      - const: lvts-calib-data-2
+
+  "#thermal-sensor-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - resets
+  - nvmem-cells
+  - nvmem-cell-names
+  - "#thermal-sensor-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8195-clk.h>
+    #include <dt-bindings/reset/mt8195-resets.h>
+    #include <dt-bindings/thermal/mediatek,lvts-thermal.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      lvts_mcu: thermal-sensor@11278000 {
+        compatible = "mediatek,mt8195-lvts-mcu";
+        reg = <0 0x11278000 0 0x1000>;
+        interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+        resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+        nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+        nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+        #thermal-sensor-cells = <1>;
+      };
+    };
+
+    thermal_zones: thermal-zones {
+      cpu0-thermal {
+        polling-delay = <1000>;
+        polling-delay-passive = <250>;
+        thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
+        trips {
+          cpu0_alert: trip-alert {
+            temperature = <85000>;
+            hysteresis = <2000>;
+            type = "passive";
+          };
+
+          cpu0_crit: trip-crit {
+            temperature = <100000>;
+            hysteresis = <2000>;
+            type = "critical";
+          };
+        };
+      };
+    };
include/dt-bindings/thermal/mediatek,lvts-thermal.h new file +19 -0
new file mode 100644
index 000000000000..ca1ef29a8fee
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/*
+ * Copyright (c) 2023 MediaTek Inc.
+ * Author: Balsam CHIHI <[email protected]>
+ */
+
+#ifndef __MEDIATEK_LVTS_DT_H
+#define __MEDIATEK_LVTS_DT_H
+
+#define MT8195_MCU_BIG_CPU0		0
+#define MT8195_MCU_BIG_CPU1		1
+#define MT8195_MCU_BIG_CPU2		2
+#define MT8195_MCU_BIG_CPU3		3
+#define MT8195_MCU_LITTLE_CPU0	4
+#define MT8195_MCU_LITTLE_CPU1	5
+#define MT8195_MCU_LITTLE_CPU2	6
+#define MT8195_MCU_LITTLE_CPU3	7
+
+#endif /* __MEDIATEK_LVTS_DT_H */
Signature · 1 line
2.34.1
#22 lore raw

Re: [PATCH v3] dt-bindings: thermal: mediatek: Add LVTS thermal controllers

Quoted 4 lines · On 31/01/2023 15:04, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Quoted 8 lines

---
Changelog:
v3:
- Fixed subject prefix
- Fixed licenses GPL-2.0-only OR BSD-2-Clause to GPL-2.0 OR MIT (to match DT)
- Fixed matching dt-binding file names

If this is v3 with only one patch, where is the driver or DTS using these bindings? Please link it. It's unusual to see only bindings, without the users.

Quoted 4 lines

v2:
- Fixed subject prefix
- Fixed licenses GPL-2.0+ to GPL-2.0
- Added dual licenses

Is there a reason to make our review more difficult and keep versions broken, threads attached to some other threads?

------------

Grabbing thread from lore.kernel.org/all/20230131140439.600164-1-bchihi%40baylibre.com/t.mbox.gz Checking for newer revisions on https://lore.kernel.org/all/
Analyzing 38 messages in the thread
Will use the latest revision: v12
You can pick other revisions using the -vN flag
Checking attestation on all messages, may take a moment...
---
✓ [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal
Sensor driver

    ✓ Signed: DKIM/baylibre-com.20210112.gappssmtp.com (From:

[email protected])
+ Link:
https://lore.kernel.org/r/[email protected]
✓ [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal
controllers dt-binding definition

    ✓ Signed: DKIM/baylibre-com.20210112.gappssmtp.com (From:

[email protected])
+ Link:
https://lore.kernel.org/r/[email protected]
ERROR: missing [3/1]!
ERROR: missing [4/1]!
ERROR: missing [5/1]!
ERROR: missing [6/1]!

--------

b4 diff '<[email protected]>' Checking for older revisions on https://lore.kernel.org/all/
---
Analyzing 38 messages in the thread
Assuming new revision: v4 ([PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver)
Preparing fake-am for v3: dt-bindings: thermal: mediatek: Add LVTS thermal controllers
range: 291580cde5f6..de7fe5e0293a
Preparing fake-am for v12: arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes
ERROR: Could not find matching blob for
arch/arm64/boot/dts/mediatek/mt8195.dtsi (09df105f4606)
If you know on which tree this patchset is based, add it as a remote and perform "git remote update" in order to fetch the missing objects.
---
Could not create fake-am range for upper series v12

Quoted 14 lines

---

---
 .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
 .../thermal/mediatek,lvts-thermal.h           |  19 ++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 include/dt-bindings/thermal/mediatek,lvts-thermal.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +0 -0
new file mode 100644
index 000000000000..5fa5c7a1a417

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 1

Quoted 1 line
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +1 -0
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0 OR MIT)

WARNING: DT binding documents should be licensed (GPL-2.0-only OR BSD-2-Clause)
#24: FILE:
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml:1:
+# SPDX-License-Identifier: (GPL-2.0 OR MIT)

I asked you to use the binding license for header file. Then you changed binding license... why? Why do you need other SPDX text? Why do you need MIT?

Quoted 11 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +11 -0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 22

Quoted 10 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +10 -0
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu

What about other devices? You called the file name as generic for all Mediatek SoCs, so why only one SoC is here? Is there going to be more? If yes, why they cannot be added now?

Best regards,
Krzysztof

#23 lore raw

Re: [PATCH v3] dt-bindings: thermal: mediatek: Add LVTS thermal controllers

Hi Krzysztof

Quoted 15 lines · Krzysztof Kozlowski
Quoted 4 lines · On 31/01/2023 15:04, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add LVTS thermal controllers dt-binding definition for mt8195.

Quoted 8 lines

---
Changelog:
v3:
- Fixed subject prefix
- Fixed licenses GPL-2.0-only OR BSD-2-Clause to GPL-2.0 OR MIT (to match DT)
- Fixed matching dt-binding file names

Quoted 3 lines

If this is v3 with only one patch, where is the driver or DTS using these bindings? Please link it. It's unusual to see only bindings, without the users.

sorry, I'll be careful next time.
and I will take into account the new change requests in the next full version of the series.
I apologize for the mess.

Quoted 8 lines
Quoted 5 lines

v2:
- Fixed subject prefix
- Fixed licenses GPL-2.0+ to GPL-2.0
- Added dual licenses

Is there a reason to make our review more difficult and keep versions broken, threads attached to some other threads?

sorry again.

Quoted 72 lines

------------

Grabbing thread from lore.kernel.org/all/20230131140439.600164-1-bchihi%40baylibre.com/t.mbox.gz Checking for newer revisions on https://lore.kernel.org/all/
Analyzing 38 messages in the thread
Will use the latest revision: v12
You can pick other revisions using the -vN flag
Checking attestation on all messages, may take a moment...
---
✓ [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal
Sensor driver

    ✓ Signed: DKIM/baylibre-com.20210112.gappssmtp.com (From:

[email protected])
+ Link:
https://lore.kernel.org/r/[email protected]
✓ [PATCH v12 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal
controllers dt-binding definition

    ✓ Signed: DKIM/baylibre-com.20210112.gappssmtp.com (From:

[email protected])
+ Link:
https://lore.kernel.org/r/[email protected]
ERROR: missing [3/1]!
ERROR: missing [4/1]!
ERROR: missing [5/1]!
ERROR: missing [6/1]!

--------

b4 diff '<[email protected]>' Checking for older revisions on https://lore.kernel.org/all/
---
Analyzing 38 messages in the thread
Assuming new revision: v4 ([PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver)
Preparing fake-am for v3: dt-bindings: thermal: mediatek: Add LVTS thermal controllers
range: 291580cde5f6..de7fe5e0293a
Preparing fake-am for v12: arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes
ERROR: Could not find matching blob for
arch/arm64/boot/dts/mediatek/mt8195.dtsi (09df105f4606)
If you know on which tree this patchset is based, add it as a remote and perform "git remote update" in order to fetch the missing objects.
---
Could not create fake-am range for upper series v12

Quoted 14 lines

---

---
 .../thermal/mediatek,lvts-thermal.yaml        | 107 ++++++++++++++++++
 .../thermal/mediatek,lvts-thermal.h           |  19 ++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
 create mode 100644 include/dt-bindings/thermal/mediatek,lvts-thermal.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +0 -0
new file mode 100644
index 000000000000..5fa5c7a1a417

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 1

Quoted 1 line
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +1 -0
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0 OR MIT)

WARNING: DT binding documents should be licensed (GPL-2.0-only OR BSD-2-Clause)
#24: FILE:
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml:1:
+# SPDX-License-Identifier: (GPL-2.0 OR MIT)

Quoted 3 lines

I asked you to use the binding license for header file. Then you changed binding license... why? Why do you need other SPDX text? Why do you need MIT?

I will put it back "GPL-2.0-only OR BSD-2-Clause" in the binding and do the same for the header.

Quoted 18 lines
Quoted 18 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +17 -0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek SoC Low Voltage Thermal Sensor (LVTS)
+
+maintainers:
+  - Balsam CHIHI <[email protected]>
+
+description: |
+  LVTS is a thermal management architecture composed of three subsystems,
+  a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU),
+  a Converter - Low Voltage Thermal Sensor converter (LVTS), and
+  a Digital controller (LVTS_CTRL).
+
+properties:
Quoted 8 lines

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 22

Quoted 4 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +4 -0
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu

What about other devices? You called the file name as generic for all Mediatek SoCs, so why only one SoC is here? Is there going to be more? If yes, why they cannot be added now?

Yes, there is another MTK SoC mt8192 that supports LVTS,
I was asked in v10 of the series to remove the unimplemented SoC. It will be added later with the driver that supports it. just let me know if you still want to add mt8192 bindings in the next version without the driver.
(LVTS support for mt8192 will be sent in a different series).

Quoted 4 lines

Best regards,
Krzysztof

#24 lore raw

Re: [PATCH v3] dt-bindings: thermal: mediatek: Add LVTS thermal controllers

Quoted 11 lines · Balsam CHIHI
Quoted 10 lines

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 22

Quoted 6 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +6 -0
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu

What about other devices? You called the file name as generic for all Mediatek SoCs, so why only one SoC is here? Is there going to be more? If yes, why they cannot be added now?

Quoted 5 lines

Yes, there is another MTK SoC mt8192 that supports LVTS,
I was asked in v10 of the series to remove the unimplemented SoC. It will be added later with the driver that supports it. just let me know if you still want to add mt8192 bindings in the next version without the driver.

The binding should be complete, if that's possible, so if you had mt8192 already there, it could stay. Anyway it's fine then.

Best regards,
Krzysztof

#25 lore raw

Re: [PATCH v3] dt-bindings: thermal: mediatek: Add LVTS thermal controllers

Hi Krzysztof,

Quoted 13 lines · Krzysztof Kozlowski
Quoted 11 lines · Balsam CHIHI
Quoted 10 lines

Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 22

Quoted 6 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +6 -0
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8195-lvts-ap
+      - mediatek,mt8195-lvts-mcu

What about other devices? You called the file name as generic for all Mediatek SoCs, so why only one SoC is here? Is there going to be more? If yes, why they cannot be added now?

Quoted 8 lines
Quoted 5 lines

Yes, there is another MTK SoC mt8192 that supports LVTS,
I was asked in v10 of the series to remove the unimplemented SoC. It will be added later with the driver that supports it. just let me know if you still want to add mt8192 bindings in the next version without the driver.

The binding should be complete, if that's possible, so if you had mt8192 already there, it could stay. Anyway it's fine then.

OK, I will put back mt8192 dt-bindings.
this is the link to the v10 patch "https://patchwork.kernel.org/project/linux-pm/patch/[email protected]/", it will be the same in next version (v13) of series.
it would be great if you review it in advance, so I could take into
account the new changes if needed.
is it possible to resend this patch under v13, to simplify the review
and avoid breaking the series again?

Quoted 4 lines

Best regards,
Krzysztof

Best regards,
Balsam

#26 lore raw

PATCH 1/1 thermal/drivers/mediatek/lvts_thermal: fix memcpy's number of bytes in lvts_calibration_init()

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

Replace memcpy 2 bytes by sizeof(int) bytes of LVTS calibration data.

---
Rebased on top of thermal/linux-next
base-commit: 6828e402d06f7c574430b61c05db784cd847b19f

Original email :
Hello Balsam CHIHI,

The patch f5f633b18234: "thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver" from Feb 9, 2023, leads to the following Smatch static checker warning:

        drivers/thermal/mediatek/lvts_thermal.c:562 lvts_calibration_init()
        warn: not copying enough bytes for '&lvts_ctrl->calibration[i]' (4 vs 2 bytes)

drivers/thermal/mediatek/lvts_thermal.c

    555 static int lvts_calibration_init(struct device *dev, struct lvts_ctrl *lvts_ctrl,
    556                                         const struct lvts_ctrl_data *lvts_ctrl_data,
    557                                         u8 *efuse_calibration)
    558 {
    559         int i;
    560
    561         for (i = 0; i < lvts_ctrl_data->num_lvts_sensor; i++)
--> 562                 memcpy(&lvts_ctrl->calibration[i],
    563                        efuse_calibration + lvts_ctrl_data->cal_offset[i], 2);
                                                                                  ^

This is copying an array of known ints to a u32 array. It should copy sizeof(int) instead of 2. It only works because the data you're on little endian and the data is small.

    564
    565         return 0;
    566 }

regards,
dan carpenter
---

---
 drivers/thermal/mediatek/lvts_thermal.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/thermal/mediatek/lvts_thermal.c +1 -1
index ddfdcbcf6d86..b505c6b49031 100644
@@ -575,7 +575,7 @@ static int lvts_calibration_init(struct device *dev, struct lvts_ctrl *lvts_ctrl
 
 	for (i = 0; i < lvts_ctrl_data->num_lvts_sensor; i++)
 		memcpy(&lvts_ctrl->calibration[i],
-		       efuse_calibration + lvts_ctrl_data->cal_offset[i], 2);
+		       efuse_calibration + lvts_ctrl_data->cal_offset[i], sizeof(int));
 
 	return 0;
 }

base-commit: 6828e402d06f7c574430b61c05db784cd847b19f
prerequisite-patch-id: 73be949bd16979769e5b94905b244dcee4a8f687
prerequisite-patch-id: d23d83a946e5b876ef01a717fd51b07df1fa08dd
prerequisite-patch-id: d67f2455eef1c4a9ecc460dbf3c2e3ad47d213ec
prerequisite-patch-id: 9076e9b3bd3cc411b7b80344211364db5f0cca17
prerequisite-patch-id: e220d6ae26786f524c249588433f02e5f5f906ad
prerequisite-patch-id: b407d2998e57678952128b3a4bac92a379132b09
prerequisite-patch-id: fbb9212ce8c3530da17d213f56fa334ce4fa1b2b
prerequisite-patch-id: 5db9eed2659028cf4419f2de3d093af7df6c2dad
prerequisite-patch-id: a83c00c628605d1c8fbe1d97074f9f28efb1bcfc
prerequisite-patch-id: 56a245620a4f8238cf1ba3844dc348de3db33845
prerequisite-patch-id: 7df24b0bf11129ddd3356eacf192cc3fdb2bcded
prerequisite-patch-id: 3213ca70cb5b26d54a7137ff40ca8cd2a795c414
prerequisite-patch-id: 6c2202e85215d1c7e8ab16a6b85922e994c68d9b

Signature · 1 line
2.34.1
#27 lore raw

Re: [PATCH] thermal/drivers/mediatek/lvts_thermal: fix memcpy's number of bytes in lvts_calibration_init()

Il 07/03/23 14:42, [email protected] ha scritto:

Quoted 3 lines

From: Balsam CHIHI <[email protected]>

Replace memcpy 2 bytes by sizeof(int) bytes of LVTS calibration data.

sizeof(int) is architecture dependant... please use a fixed size type instead.

Also, shouldn't this be u16?!

Regards,
Angelo

#28 lore raw

Re: [PATCH] thermal/drivers/mediatek/lvts_thermal: fix memcpy's number of bytes in lvts_calibration_init()

Quoted 7 lines · AngeloGioacchino Del Regno

Il 07/03/23 14:42, [email protected] ha scritto:

Quoted 3 lines

From: Balsam CHIHI <[email protected]>

Replace memcpy 2 bytes by sizeof(int) bytes of LVTS calibration data.

sizeof(int) is architecture dependant...

On Linux sizeof(int) is always 4.

I'm just so confused what you are talking about. Are you thinking about sizeof(long)? Are you thinking about CPUs from the 1970s? Linux wasn't invented until the 90s so the old CPUs were already in museums at that point.

Quoted 1 line

please use a fixed size type instead.

This is an unusual style opinion that I have not heard before. Hopefully, you just got ints and longs confused so we can move on without discussing it too much. We're copying an int so sizeof(int) is obviously correct. It's hard to know how to respond.

Quoted 1 line

Also, shouldn't this be u16?!

What? Why would you think that?

regards,
dan carpenter

#29 lore raw

PATCH v11 3/6 arm64/dts/mt8195: Add efuse node to mt8195

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

Add efuse node.
This will be required by the thermal driver to get the calibration data.

---
 arch/arm64/boot/dts/mediatek/mt8195.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +6 -0
index 5d31536f4c48..09df105f4606 100644
@@ -1380,6 +1380,12 @@ pciephy_glb_intr: pciephy-glb-intr@193 {
 			dp_calibration: dp-data@1ac {
 				reg = <0x1ac 0x10>;
 			};
+			lvts_efuse_data1: lvts1-calib@1bc {
+				reg = <0x1bc 0x14>;
+			};
+			lvts_efuse_data2: lvts2-calib@1d0 {
+				reg = <0x1d0 0x38>;
+			};
 		};
 
 		u3phy2: t-phy@11c40000 {
Signature · 1 line
2.34.1
maintainer
#30 lore raw

Re: [PATCH v11 3/6] arm64/dts/mt8195: Add efuse node to mt8195

Quoted 8 lines · On 24/01/2023 14:17, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add efuse node.
This will be required by the thermal driver to get the calibration data.

I fixed the subject prefix to:
arm64: dts: mt8195: ...
to be in line with other commits.
Please take that into account for future patches you send.

Applied thanks!

Quoted 21 lines
---
  arch/arm64/boot/dts/mediatek/mt8195.dtsi | 6 ++++++
  1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +6 -0
index 5d31536f4c48..09df105f4606 100644
@@ -1380,6 +1380,12 @@ pciephy_glb_intr: pciephy-glb-intr@193 {
  			dp_calibration: dp-data@1ac {
  				reg = <0x1ac 0x10>;
  			};
+			lvts_efuse_data1: lvts1-calib@1bc {
+				reg = <0x1bc 0x14>;
+			};
+			lvts_efuse_data2: lvts2-calib@1d0 {
+				reg = <0x1d0 0x38>;
+			};
  		};
 
  		u3phy2: t-phy@11c40000 {
#31 lore raw

Re: [PATCH v11 3/6] arm64/dts/mt8195: Add efuse node to mt8195

Quoted 13 lines · Matthias Brugger
Quoted 8 lines · On 24/01/2023 14:17, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

Add efuse node.
This will be required by the thermal driver to get the calibration data.

Quoted 7 lines

I fixed the subject prefix to:
arm64: dts: mt8195: ...
to be in line with other commits.
Please take that into account for future patches you send.

Applied thanks!

Hi Matthias,

Thank you for the fix and for applying the patch!

Best regards,
Balsam

Quoted 21 lines
Quoted 21 lines
---
  arch/arm64/boot/dts/mediatek/mt8195.dtsi | 6 ++++++
  1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +6 -0
index 5d31536f4c48..09df105f4606 100644
@@ -1380,6 +1380,12 @@ pciephy_glb_intr: pciephy-glb-intr@193 {
                      dp_calibration: dp-data@1ac {
                              reg = <0x1ac 0x10>;
                      };
+                     lvts_efuse_data1: lvts1-calib@1bc {
+                             reg = <0x1bc 0x14>;
+                     };
+                     lvts_efuse_data2: lvts2-calib@1d0 {
+                             reg = <0x1d0 0x38>;
+                     };
              };
 
              u3phy2: t-phy@11c40000 {
#32 lore raw

PATCH v11 4/6 thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

The interrupt is managed at the thermal controller level, so when an interrupt occurs, the driver has to find out which sensor triggered such an interrupt.

The sampling of the thermal can be filtered or immediate. For the former, the LVTS measures several points and applies a low pass filter.

---
 drivers/thermal/mediatek/Kconfig        |   15 +
 drivers/thermal/mediatek/Makefile       |    1 +
 drivers/thermal/mediatek/lvts_thermal.c | 1261 +++++++++++++++++++++++
 3 files changed, 1277 insertions(+)
 create mode 100644 drivers/thermal/mediatek/lvts_thermal.c
drivers/thermal/mediatek/Kconfig +15 -0
index 7558a847d4e9..99597d7b9890 100644
@@ -18,4 +18,19 @@ config MTK_SOC_THERMAL
 	  This driver configures thermal controllers to collect
 	  temperature via AUXADC interface.
 
+config MTK_LVTS_THERMAL
+        tristate "LVTS Thermal Driver for MediaTek SoCs"
+        depends on HAS_IOMEM
+        help
+          Enable this option if you want to get SoC temperature
+          information for supported MediaTek platforms.
+          This driver configures LVTS (Low Voltage Thermal Sensor)
+          thermal controllers to collect temperatures via ASIF
+          (Analog Serial Interface).
+
+config MTK_LVTS_THERMAL_DEBUGFS
+       bool "LVTS thermal debugfs"
+       depends on MTK_LVTS_THERMAL && DEBUG_FS
+       help
+         Enable this option to debug the internals of the device driver.
 endif
drivers/thermal/mediatek/Makefile +1 -0
index 53e86e30b26f..1c6daa1e644b 100644
@@ -1 +1,2 @@
 obj-$(CONFIG_MTK_SOC_THERMAL)	+= auxadc_thermal.o
+obj-$(CONFIG_MTK_LVTS_THERMAL)	+= lvts_thermal.o
drivers/thermal/mediatek/lvts_thermal.c new file +1261 -0

1,261 lines not on this page · raw message

Signature · 1 line
2.34.1
maintainer Reviewed-by Tested-by on v11 4/6
#33 lore raw

Re: [PATCH v11 4/6] thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 19 lines

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

The interrupt is managed at the thermal controller level, so when an interrupt occurs, the driver has to find out which sensor triggered such an interrupt.

Quoted 5 lines

The sampling of the thermal can be filtered or immediate. For the former, the LVTS measures several points and applies a low pass filter.

On MT8195 Tomato Chromebook:

#34 lore raw

Re: [PATCH v11 4/6] thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver

Quoted 25 lines · AngeloGioacchino Del Regno

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 23 lines

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

The interrupt is managed at the thermal controller level, so when an interrupt occurs, the driver has to find out which sensor triggered such an interrupt.

The sampling of the thermal can be filtered or immediate. For the former, the LVTS measures several points and applies a low pass filter.

Quoted 6 lines
Quoted 1 line

On MT8195 Tomato Chromebook:

Hi Angelo,

Thank you for reviewing and testing it.

Best regards,
Balsam

#35 lore raw

PATCH v12 1/1 thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

The interrupt is managed at the thermal controller level, so when an interrupt occurs, the driver has to find out which sensor triggered such an interrupt.

The sampling of the thermal can be filtered or immediate. For the former, the LVTS measures several points and applies a low pass filter.

On MT8195 Tomato Chromebook:

---
Changelog:
v12:
- Fixed subject prefix
- Rename "include/dt-bindings/thermal/mediatek-lvts.h" to "include/dt-bindings/thermal/mediatek,lvts-thermal.h" due to this patch
https://lore.kernel.org/all/[email protected]/
---

---
 drivers/thermal/mediatek/Kconfig        |   16 +
 drivers/thermal/mediatek/Makefile       |    1 +
 drivers/thermal/mediatek/lvts_thermal.c | 1261 +++++++++++++++++++++++
 3 files changed, 1278 insertions(+)
 create mode 100644 drivers/thermal/mediatek/lvts_thermal.c
drivers/thermal/mediatek/Kconfig +16 -0
index 7558a847d4e9..d82c86d9be56 100644
@@ -18,4 +18,20 @@ config MTK_SOC_THERMAL
 	  This driver configures thermal controllers to collect
 	  temperature via AUXADC interface.
 
+config MTK_LVTS_THERMAL
+        tristate "LVTS Thermal Driver for MediaTek SoCs"
+        depends on HAS_IOMEM
+        help
+          Enable this option if you want to get SoC temperature
+          information for supported MediaTek platforms.
+          This driver configures LVTS (Low Voltage Thermal Sensor)
+          thermal controllers to collect temperatures via ASIF
+          (Analog Serial Interface).
+
+config MTK_LVTS_THERMAL_DEBUGFS
+       bool "LVTS thermal debugfs"
+       depends on MTK_LVTS_THERMAL && DEBUG_FS
+       help
+         Enable this option to debug the internals of the device driver.
+
 endif
drivers/thermal/mediatek/Makefile +1 -0
index 53e86e30b26f..1c6daa1e644b 100644
@@ -1 +1,2 @@
 obj-$(CONFIG_MTK_SOC_THERMAL)	+= auxadc_thermal.o
+obj-$(CONFIG_MTK_LVTS_THERMAL)	+= lvts_thermal.o
drivers/thermal/mediatek/lvts_thermal.c new file +1261 -0

1,261 lines not on this page · raw message

Signature · 1 line
2.34.1
#36 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Thank you for the patch! Yet something to improve:

Hi Balsam,

Thank you for the patch! Yet something to improve:

url:    https://github.com/intel-lab-lkp/linux/commits/UPDATE-20230131-234122/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230124-211910
base:   the 4th patch of https://lore.kernel.org/r/20230124131717.128660-5-bchihi%40baylibre.com
patch link:    https://lore.kernel.org/r/20230131153816.21709-1-bchihi%40baylibre.com
patch subject: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver
config: s390-allyesconfig (https://download.01.org/0day-ci/archive/20230201/[email protected]/config)
compiler: s390-linux-gcc (GCC) 12.1.0

reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/5646ebf6f10ff0fc60c04d8c57523f7c44526b41
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review UPDATE-20230131-234122/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230124-211910 git checkout 5646ebf6f10ff0fc60c04d8c57523f7c44526b41
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=s390 olddefconfig COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=s390 SHELL=/bin/bash

If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <[email protected]>

All errors (new ones prefixed by >>):

>> drivers/thermal/mediatek/lvts_thermal.c:20:10: fatal error: dt-bindings/thermal/mediatek,lvts-thermal.h: No such file or directory

20 | #include <dt-bindings/thermal/mediatek,lvts-thermal.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.

vim +20 drivers/thermal/mediatek/lvts_thermal.c

  > 20	#include <dt-bindings/thermal/mediatek,lvts-thermal.h>
    21	
Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests
#37 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Quoted 24 lines · kernel test robot

Hi Balsam,

Thank you for the patch! Yet something to improve:

url:    https://github.com/intel-lab-lkp/linux/commits/UPDATE-20230131-234122/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230124-211910
base:   the 4th patch of https://lore.kernel.org/r/20230124131717.128660-5-bchihi%40baylibre.com
patch link:    https://lore.kernel.org/r/20230131153816.21709-1-bchihi%40baylibre.com
patch subject: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver
config: s390-allyesconfig (https://download.01.org/0day-ci/archive/20230201/[email protected]/config)
compiler: s390-linux-gcc (GCC) 12.1.0

reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/5646ebf6f10ff0fc60c04d8c57523f7c44526b41
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review UPDATE-20230131-234122/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230124-211910 git checkout 5646ebf6f10ff0fc60c04d8c57523f7c44526b41
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=s390 olddefconfig COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=s390 SHELL=/bin/bash

Quoted 8 lines

If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <[email protected]>

All errors (new ones prefixed by >>):

Quoted 1 line
Quoted 1 line

drivers/thermal/mediatek/lvts_thermal.c:20:10: fatal error: dt-bindings/thermal/mediatek,lvts-thermal.h: No such file or directory

20 | #include <dt-bindings/thermal/mediatek,lvts-thermal.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

So here is your driver... and you decided not only to make reviewers life more difficult, but also to fail all automated tools.

No, that's not how patchsets should be sent. You have here clear dependency, you cannot send them separately.

Best regards,
Krzysztof

#38 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Hi Krzysztof,

Quoted 32 lines · Krzysztof Kozlowski
Quoted 30 lines · kernel test robot

Hi Balsam,

Thank you for the patch! Yet something to improve:

url:    https://github.com/intel-lab-lkp/linux/commits/UPDATE-20230131-234122/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230124-211910
base:   the 4th patch of https://lore.kernel.org/r/20230124131717.128660-5-bchihi%40baylibre.com
patch link:    https://lore.kernel.org/r/20230131153816.21709-1-bchihi%40baylibre.com
patch subject: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver
config: s390-allyesconfig (https://download.01.org/0day-ci/archive/20230201/[email protected]/config)
compiler: s390-linux-gcc (GCC) 12.1.0

reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/5646ebf6f10ff0fc60c04d8c57523f7c44526b41
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review UPDATE-20230131-234122/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230124-211910 git checkout 5646ebf6f10ff0fc60c04d8c57523f7c44526b41
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=s390 olddefconfig COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=s390 SHELL=/bin/bash

If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <[email protected]>

All errors (new ones prefixed by >>):

Quoted 1 line
Quoted 1 line

drivers/thermal/mediatek/lvts_thermal.c:20:10: fatal error: dt-bindings/thermal/mediatek,lvts-thermal.h: No such file or directory

Quoted 8 lines
Quoted 2 lines

20 | #include <dt-bindings/thermal/mediatek,lvts-thermal.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

So here is your driver... and you decided not only to make reviewers life more difficult, but also to fail all automated tools.

No, that's not how patchsets should be sent. You have here clear dependency, you cannot send them separately.

I'm sorry, I'll be careful next time.
I apologize for breaking the series.
I will take into account the new change requests in the next full v13 the series.

Quoted 4 lines

Best regards,
Krzysztof

Best regards,
Balsam

#39 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

In reply to [email protected]
Quoted 15 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

(...)

Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+struct lvts_domain {
+	struct lvts_ctrl *lvts_ctrl;
+	struct reset_control *reset;

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+	struct clk *clk;
+	int num_lvts_ctrl;
+	void __iomem *base;
+	size_t calib_len;
+	u8 *calib;
+};
+
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

Quoted 7 lines
drivers/thermal/mediatek/lvts_thermal.c new file +7 -0
+
+#define LVTS_DEBUG_FS_REGS(__reg)		\
+{						\
+	.name = __stringify(__reg),		\
+	.offset = __reg(0),			\
+}
+

(...)

Quoted 31 lines
drivers/thermal/mediatek/lvts_thermal.c new file +31 -0
+
+static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
+{
+	struct lvts_sensor *lvts_sensor = tz->devdata;
+	void __iomem *base = lvts_sensor->base;
+	u32 raw_low = lvts_temp_to_raw(low);
+	u32 raw_high = lvts_temp_to_raw(high);
+
+	/*
+	 * Hot to normal temperature threshold
+	 *
+	 * LVTS_H2NTHRE
+	 *
+	 * Bits:
+	 *
+	 * 14-0 : Raw temperature for threshold
+	 */
+	if (low != -INT_MAX) {
+		dev_dbg(&tz->device, "Setting low limit temperature interrupt: %d\n", low);
+		writel(raw_low, LVTS_H2NTHRE(base));
+	}
+
+	/*
+	 * Hot temperature threshold
+	 *
+	 * LVTS_HTHRE
+	 *
+	 * Bits:
+	 *
+	 * 14-0 : Raw temperature for threshold
+	 */

drivers/thermal/mediatek/lvts_thermal.c line 334

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+	dev_dbg(&tz->device, "Setting high limit temperature interrupt: %d\n", high);
+	writel(raw_high, LVTS_HTHRE(base));
+
+	return 0;
+}
+
+static irqreturn_t lvts_ctrl_irq_handler(struct lvts_ctrl *lvts_ctrl)
+{
+	irqreturn_t iret = IRQ_NONE;
+	u32 value, masks[] = {

Don't mix different types in one declaration. u32 and a pointer are quite different types.

Quoted 249 lines
drivers/thermal/mediatek/lvts_thermal.c new file +249 -0
+		LVTS_INT_SENSOR0,
+		LVTS_INT_SENSOR1,
+		LVTS_INT_SENSOR2,
+		LVTS_INT_SENSOR3
+	};
+	int i;
+
+	/*
+	 * Interrupt monitoring status
+	 *
+	 * LVTS_MONINTST
+	 *
+	 * Bits:
+	 *
+	 * 31 : Interrupt for stage 3
+	 * 30 : Interrupt for stage 2
+	 * 29 : Interrupt for state 1
+	 * 28 : Interrupt using filter on sensor 3
+	 *
+	 * 27 : Interrupt using immediate on sensor 3
+	 * 26 : Interrupt normal to hot on sensor 3
+	 * 25 : Interrupt high offset on sensor 3
+	 * 24 : Interrupt low offset on sensor 3
+	 *
+	 * 23 : Interrupt hot threshold on sensor 3
+	 * 22 : Interrupt cold threshold on sensor 3
+	 * 21 : Interrupt using filter on sensor 2
+	 * 20 : Interrupt using filter on sensor 1
+	 *
+	 * 19 : Interrupt using filter on sensor 0
+	 * 18 : Interrupt using immediate on sensor 2
+	 * 17 : Interrupt using immediate on sensor 1
+	 * 16 : Interrupt using immediate on sensor 0
+	 *
+	 * 15 : Interrupt device access timeout interrupt
+	 * 14 : Interrupt normal to hot on sensor 2
+	 * 13 : Interrupt high offset interrupt on sensor 2
+	 * 12 : Interrupt low offset interrupt on sensor 2
+	 *
+	 * 11 : Interrupt hot threshold on sensor 2
+	 * 10 : Interrupt cold threshold on sensor 2
+	 *  9 : Interrupt normal to hot on sensor 1
+	 *  8 : Interrupt high offset interrupt on sensor 1
+	 *
+	 *  7 : Interrupt low offset interrupt on sensor 1
+	 *  6 : Interrupt hot threshold on sensor 1
+	 *  5 : Interrupt cold threshold on sensor 1
+	 *  4 : Interrupt normal to hot on sensor 0
+	 *
+	 *  3 : Interrupt high offset interrupt on sensor 0
+	 *  2 : Interrupt low offset interrupt on sensor 0
+	 *  1 : Interrupt hot threshold on sensor 0
+	 *  0 : Interrupt cold threshold on sensor 0
+	 *
+	 * We are interested in the sensor(s) responsible of the
+	 * interrupt event. We update the thermal framework with the
+	 * thermal zone associated with the sensor. The framework will
+	 * take care of the rest whatever the kind of interrupt, we
+	 * are only interested in which sensor raised the interrupt.
+	 *
+	 * sensor 3 interrupt: 0001 1111 1100 0000 0000 0000 0000 0000
+	 *                  => 0x1FC00000
+	 * sensor 2 interrupt: 0000 0000 0010 0100 0111 1100 0000 0000
+	 *                  => 0x00247C00
+	 * sensor 1 interrupt: 0000 0000 0001 0001 0000 0011 1110 0000
+	 *                  => 0X000881F0
+	 * sensor 0 interrupt: 0000 0000 0000 1001 0000 0000 0001 1111
+	 *                  => 0x0009001F
+	 */
+	value = readl(LVTS_MONINTSTS(lvts_ctrl->base));
+
+	/*
+	 * Let's figure out which sensors raised the interrupt
+	 *
+	 * NOTE: the masks array must be ordered with the index
+	 * corresponding to the sensor id eg. index=0, mask for
+	 * sensor0.
+	 */
+	for (i = 0; i < ARRAY_SIZE(masks); i++) {
+
+		if (!(value & masks[i]))
+			continue;
+
+		thermal_zone_device_update(lvts_ctrl->sensors[i].tz,
+					   THERMAL_TRIP_VIOLATED);
+		iret = IRQ_HANDLED;
+	}
+
+	/*
+	 * Write back to clear the interrupt status (W1C)
+	 */
+	writel(value, LVTS_MONINTSTS(lvts_ctrl->base));
+
+	return iret;
+}
+
+/*
+ * Temperature interrupt handler. Even if the driver supports more
+ * interrupt modes, we use the interrupt when the temperature crosses
+ * the hot threshold the way up and the way down (modulo the
+ * hysteresis).
+ *
+ * Each thermal domain has a couple of interrupts, one for hardware
+ * reset and another one for all the thermal events happening on the
+ * different sensors.
+ *
+ * The interrupt is configured for thermal events when crossing the
+ * hot temperature limit. At each interrupt, we check in every
+ * controller if there is an interrupt pending.
+ */
+static irqreturn_t lvts_irq_handler(int irq, void *data)
+{
+	struct lvts_domain *lvts_td = data;
+	irqreturn_t aux, iret = IRQ_NONE;
+	int i;
+
+	for (i = 0; i < lvts_td->num_lvts_ctrl; i++) {
+
+		aux = lvts_ctrl_irq_handler(lvts_td->lvts_ctrl);
+		if (aux != IRQ_HANDLED)
+			continue;
+
+		iret = IRQ_HANDLED;
+	}
+
+	return iret;
+}
+
+static struct thermal_zone_device_ops lvts_ops = {
+	.get_temp = lvts_get_temp,
+	.set_trips = lvts_set_trips,
+};
+
+static int __init lvts_sensor_init(struct device *dev,
+				   struct lvts_ctrl *lvts_ctrl,
+				   struct lvts_ctrl_data *lvts_ctrl_data)
+{
+	struct lvts_sensor *lvts_sensor = lvts_ctrl->sensors;
+	void __iomem *msr_regs[] = {
+		LVTS_MSR0(lvts_ctrl->base),
+		LVTS_MSR1(lvts_ctrl->base),
+		LVTS_MSR2(lvts_ctrl->base),
+		LVTS_MSR3(lvts_ctrl->base)
+	};
+
+	void __iomem *imm_regs[] = {
+		LVTS_IMMD0(lvts_ctrl->base),
+		LVTS_IMMD1(lvts_ctrl->base),
+		LVTS_IMMD2(lvts_ctrl->base),
+		LVTS_IMMD3(lvts_ctrl->base)
+	};
+
+	int i;
+
+	for (i = 0; i < lvts_ctrl_data->num_lvts_sensor; i++) {
+
+		int dt_id = lvts_ctrl_data->lvts_sensor[i].dt_id;
+
+		/*
+		 * At this point, we don't know which id matches which
+		 * sensor. Let's set arbitrally the id from the index.
+		 */
+		lvts_sensor[i].id = i;
+
+		/*
+		 * The thermal zone registration will set the trip
+		 * point interrupt in the thermal controller
+		 * register. But this one will be reset in the
+		 * initialization after. So we need to post pone the
+		 * thermal zone creation after the controller is
+		 * setup. For this reason, we store the device tree
+		 * node id from the data in the sensor structure
+		 */
+		lvts_sensor[i].dt_id = dt_id;
+
+		/*
+		 * We assign the base address of the thermal
+		 * controller as a back pointer. So it will be
+		 * accessible from the different thermal framework ops
+		 * as we pass the lvts_sensor pointer as thermal zone
+		 * private data.
+		 */
+		lvts_sensor[i].base = lvts_ctrl->base;
+
+		/*
+		 * Each sensor has its own register address to read from.
+		 */
+		lvts_sensor[i].msr = lvts_ctrl_data->mode == LVTS_MSR_IMMEDIATE_MODE ?
+			imm_regs[i] : msr_regs[i];
+	};
+
+	lvts_ctrl->num_lvts_sensor = lvts_ctrl_data->num_lvts_sensor;
+
+	return 0;
+}
+
+/*
+ * The efuse blob values follows the sensor enumeration per thermal
+ * controller. The decoding of the stream is as follow:
+ *
+ *                        <--?-> <----big0 ???---> <-sensor0-> <-0->
+ *                        ------------------------------------------
+ * index in the stream: : | 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 |
+ *                        ------------------------------------------
+ *
+ *                        <--sensor1--><-0-> <----big1 ???---> <-sen
+ *                        ------------------------------------------
+ *                        | 0x7 | 0x8 | 0x9 | 0xA | 0xB | OxC | OxD |
+ *                        ------------------------------------------
+ *
+ *                        sor0-> <-0-> <-sensor1-> <-0-> ..........
+ *                        ------------------------------------------
+ *                        | 0x7 | 0x8 | 0x9 | 0xA | 0xB | OxC | OxD |
+ *                        ------------------------------------------
+ *
+ * And so on ...
+ *
+ * The data description gives the offset of the calibration data in
+ * this bytes stream for each sensor.
+ *
+ * Each thermal controller can handle up to 4 sensors max, we don't
+ * care if there are less as the array of calibration is sized to 4
+ * anyway. The unused sensor slot will be zeroed.
+ */
+static int __init lvts_calibration_init(struct device *dev,
+					struct lvts_ctrl *lvts_ctrl,
+					struct lvts_ctrl_data *lvts_ctrl_data,
+					u8 *efuse_calibration)
+{
+	int i;
+
+	for (i = 0; i < lvts_ctrl_data->num_lvts_sensor; i++)
+		memcpy(&lvts_ctrl->calibration[i],
+		       efuse_calibration + lvts_ctrl_data->cal_offset[i], 2);
+
+	return 0;
+}
+
+/*
+ * The efuse bytes stream can be split into different chunk of
+ * nvmems. This function reads and concatenate those into a single
+ * buffer so it can be read sequentially when initializing the
+ * calibration data.
+ */
+static int lvts_calibration_read(struct device *dev, struct lvts_domain *lvts_td,
+				 struct lvts_data *lvts_data)
+{
+	struct device_node *np = dev_of_node(dev);
+	struct nvmem_cell *cell;

drivers/thermal/mediatek/lvts_thermal.c line 593

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+	struct property *prop;
+	const char *cell_name;
+
+	of_property_for_each_string(np, "nvmem-cell-names", prop, cell_name) {
+		size_t len;
+		u8 *efuse;
+
+		cell = of_nvmem_cell_get(np, cell_name);
+		if (IS_ERR(cell)) {
+			dev_dbg(dev, "Failed to get cell '%s'\n", cell_name);

Is this an error? If so, why debug? dbg is not for errors.

Quoted 18 lines
drivers/thermal/mediatek/lvts_thermal.c new file +18 -0
+			return PTR_ERR(cell);
+		}
+
+		efuse = nvmem_cell_read(cell, &len);
+
+		nvmem_cell_put(cell);
+
+		if (IS_ERR(efuse)) {
+			dev_dbg(dev, "Failed to read cell '%s'\n", cell_name);
+			return PTR_ERR(efuse);
+		}
+
+		lvts_td->calib = devm_krealloc(dev, lvts_td->calib,
+					       lvts_td->calib_len + len, GFP_KERNEL);
+		if (!lvts_td->calib)
+			return -ENOMEM;
+
+		memcpy(lvts_td->calib + lvts_td->calib_len, efuse, len);

drivers/thermal/mediatek/lvts_thermal.c line 621

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+
+		lvts_td->calib_len += len;
+
+		kfree(efuse);
+	}
+
+	return 0;
+}
+
+static int __init lvts_golden_temp_init(struct device *dev, u32 *value)

You did not test it, right? Build with section mismatch analysis...

Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+{
+	u32 gt;
+
+	gt = (*value) >> 24;

drivers/thermal/mediatek/lvts_thermal.c line 635

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+
+	if (gt && gt < LVTS_GOLDEN_TEMP_MAX)
+		golden_temp = gt;
+
+	coeff_b = golden_temp * 500 + LVTS_COEFF_B;
+
+	return 0;
+}
+
+static int __init lvts_ctrl_init(struct device *dev,

Same problem.

drivers/thermal/mediatek/lvts_thermal.c

Quoted 12 lines
drivers/thermal/mediatek/lvts_thermal.c new file +11 -0
+				 struct lvts_domain *lvts_td,
+				 struct lvts_data *lvts_data)
+{
+	size_t size = sizeof(*lvts_td->lvts_ctrl) * lvts_data->num_lvts_ctrl;
+	struct lvts_ctrl *lvts_ctrl;
+	int i, ret;
+
 
+
+static inline int lvts_ctrl_enable(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+	return lvts_ctrl_set_enable(lvts_ctrl, 1);

Drop the wrapper, it's useless. true or false for enable are quite obvious.

drivers/thermal/mediatek/lvts_thermal.c line 797

Quoted 5 lines
drivers/thermal/mediatek/lvts_thermal.c new file +5 -0
+}
+
+static inline int lvts_ctrl_disable(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+	return lvts_ctrl_set_enable(lvts_ctrl, 0);

Drop the wrapper.

Quoted 320 lines
drivers/thermal/mediatek/lvts_thermal.c new file +320 -0
+}
+
+static int lvts_ctrl_connect(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+	u32 id, cmds[] = { 0xC103FFFF, 0xC502FF55 };
+
+	lvts_write_config(lvts_ctrl, cmds, ARRAY_SIZE(cmds));
+
+	/*
+	 * LVTS_ID : Get ID and status of the thermal controller
+	 *
+	 * Bits:
+	 *
+	 * 0-5	: thermal controller id
+	 *   7	: thermal controller connection is valid
+	 */
+	id = readl(LVTS_ID(lvts_ctrl->base));
+	if (!(id & BIT(7)))
+		return -EIO;
+
+	return 0;
+}
+
+static int lvts_ctrl_initialize(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+	/*
+	 * Write device mask: 0xC1030000
+	 */
+	u32 cmds[] = {
+		0xC1030E01, 0xC1030CFC, 0xC1030A8C, 0xC103098D, 0xC10308F1,
+		0xC10307A6, 0xC10306B8, 0xC1030500, 0xC1030420, 0xC1030300,
+		0xC1030030, 0xC10300F6, 0xC1030050, 0xC1030060, 0xC10300AC,
+		0xC10300FC, 0xC103009D, 0xC10300F1, 0xC10300E1
+	};
+
+	lvts_write_config(lvts_ctrl, cmds, ARRAY_SIZE(cmds));
+
+	return 0;
+}
+
+static int lvts_ctrl_calibrate(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+	int i;
+	void __iomem *lvts_edata[] = {
+		LVTS_EDATA00(lvts_ctrl->base),
+		LVTS_EDATA01(lvts_ctrl->base),
+		LVTS_EDATA02(lvts_ctrl->base),
+		LVTS_EDATA03(lvts_ctrl->base)
+	};
+
+	/*
+	 * LVTS_EDATA0X : Efuse calibration reference value for sensor X
+	 *
+	 * Bits:
+	 *
+	 * 20-0 : Efuse value for normalization data
+	 */
+	for (i = 0; i < LVTS_SENSOR_MAX; i++)
+		writel(lvts_ctrl->calibration[i], lvts_edata[i]);
+
+	return 0;
+}
+
+static int lvts_ctrl_configure(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+	u32 value;
+
+	/*
+	 * LVTS_TSSEL : Sensing point index numbering
+	 *
+	 * Bits:
+	 *
+	 * 31-24: ADC Sense 3
+	 * 23-16: ADC Sense 2
+	 * 15-8	: ADC Sense 1
+	 * 7-0	: ADC Sense 0
+	 */
+	value = LVTS_TSSEL_CONF;
+	writel(value, LVTS_TSSEL(lvts_ctrl->base));
+
+	/*
+	 * LVTS_CALSCALE : ADC voltage round
+	 */
+	value = 0x300;
+	value = LVTS_CALSCALE_CONF;
+
+	/*
+	 * LVTS_MSRCTL0 : Sensor filtering strategy
+	 *
+	 * Filters:
+	 *
+	 * 000 : One sample
+	 * 001 : Avg 2 samples
+	 * 010 : 4 samples, drop min and max, avg 2 samples
+	 * 011 : 6 samples, drop min and max, avg 4 samples
+	 * 100 : 10 samples, drop min and max, avg 8 samples
+	 * 101 : 18 samples, drop min and max, avg 16 samples
+	 *
+	 * Bits:
+	 *
+	 * 0-2  : Sensor0 filter
+	 * 3-5  : Sensor1 filter
+	 * 6-8  : Sensor2 filter
+	 * 9-11 : Sensor3 filter
+	 */
+	value = LVTS_HW_FILTER << 9 |  LVTS_HW_FILTER << 6 |
+			LVTS_HW_FILTER << 3 | LVTS_HW_FILTER;
+	writel(value, LVTS_MSRCTL0(lvts_ctrl->base));
+
+	/*
+	 * LVTS_MSRCTL1 : Measurement control
+	 *
+	 * Bits:
+	 *
+	 * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3
+	 * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2
+	 * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1
+	 * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0
+	 *
+	 * That configuration will ignore the filtering and the delays
+	 * introduced below in MONCTL1 and MONCTL2
+	 */
+	if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) {
+		value = BIT(9) | BIT(6) | BIT(5) | BIT(4);
+		writel(value, LVTS_MSRCTL1(lvts_ctrl->base));
+	}
+
+	/*
+	 * LVTS_MONCTL1 : Period unit and group interval configuration
+	 *
+	 * The clock source of LVTS thermal controller is 26MHz.
+	 *
+	 * The period unit is a time base for all the interval delays
+	 * specified in the registers. By default we use 12. The time
+	 * conversion is done by multiplying by 256 and 1/26.10^6
+	 *
+	 * An interval delay multiplied by the period unit gives the
+	 * duration in seconds.
+	 *
+	 * - Filter interval delay is a delay between two samples of
+	 * the same sensor.
+	 *
+	 * - Sensor interval delay is a delay between two samples of
+	 * different sensors.
+	 *
+	 * - Group interval delay is a delay between different rounds.
+	 *
+	 * For example:
+	 *     If Period unit = C, filter delay = 1, sensor delay = 2, group delay = 1,
+	 *     and two sensors, TS1 and TS2, are in a LVTS thermal controller
+	 *     and then
+	 *     Period unit time = C * 1/26M * 256 = 12 * 38.46ns * 256 = 118.149us
+	 *     Filter interval delay = 1 * Period unit = 118.149us
+	 *     Sensor interval delay = 2 * Period unit = 236.298us
+	 *     Group interval delay = 1 * Period unit = 118.149us
+	 *
+	 *     TS1    TS1 ... TS1    TS2    TS2 ... TS2    TS1...
+	 *        <--> Filter interval delay
+	 *                       <--> Sensor interval delay
+	 *                                             <--> Group interval delay
+	 * Bits:
+	 *      29 - 20 : Group interval
+	 *      16 - 13 : Send a single interrupt when crossing the hot threshold (1)
+	 *                or an interrupt everytime the hot threshold is crossed (0)
+	 *       9 - 0  : Period unit
+	 *
+	 */
+	value = LVTS_GROUP_INTERVAL << 20 | LVTS_PERIOD_UNIT;
+	writel(value, LVTS_MONCTL1(lvts_ctrl->base));
+
+	/*
+	 * LVTS_MONCTL2 : Filtering and sensor interval
+	 *
+	 * Bits:
+	 *
+	 *      25-16 : Interval unit in PERIOD_UNIT between sample on
+	 *              the same sensor, filter interval
+	 *       9-0  : Interval unit in PERIOD_UNIT between each sensor
+	 *
+	 */
+	value = LVTS_FILTER_INTERVAL << 16 | LVTS_SENSOR_INTERVAL;
+	writel(value, LVTS_MONCTL2(lvts_ctrl->base));
+
+	return lvts_irq_init(lvts_ctrl);
+}
+
+static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+	struct lvts_sensor *lvts_sensors = lvts_ctrl->sensors;
+	struct thermal_zone_device *tz;
+	u32 sensor_map = 0;
+	int i;
+
+	for (i = 0; i < lvts_ctrl->num_lvts_sensor; i++) {
+
+		int dt_id = lvts_sensors[i].dt_id;
+
+		tz = devm_thermal_of_zone_register(dev, dt_id, &lvts_sensors[i],
+						   &lvts_ops);
+		if (IS_ERR(tz)) {
+			/*
+			 * This thermal zone is not described in the
+			 * device tree. It is not an error from the
+			 * thermal OF code POV, we just continue.
+			 */
+			if (PTR_ERR(tz) == -ENODEV)
+				continue;
+
+			return PTR_ERR(tz);
+		}
+
+		/*
+		 * The thermal zone pointer will be needed in the
+		 * interrupt handler, we store it in the sensor
+		 * structure. The thermal domain structure will be
+		 * passed to the interrupt handler private data as the
+		 * interrupt is shared for all the controller
+		 * belonging to the thermal domain.
+		 */
+		lvts_sensors[i].tz = tz;
+
+		/*
+		 * This sensor was correctly associated with a thermal
+		 * zone, let's set the corresponding bit in the sensor
+		 * map, so we can enable the temperature monitoring in
+		 * the hardware thermal controller.
+		 */
+		sensor_map |= BIT(i);
+	}
+
+	/*
+	 * Bits:
+	 *      9: Single point access flow
+	 *    0-3: Enable sensing point 0-3
+	 *
+	 * The initialization of the thermal zones give us
+	 * which sensor point to enable. If any thermal zone
+	 * was not described in the device tree, it won't be
+	 * enabled here in the sensor map.
+	 */
+	writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base));
+
+	return 0;
+}
+
+static int lvts_domain_init(struct device *dev, struct lvts_domain *lvts_td,
+			    struct lvts_data *lvts_data)
+{
+	struct lvts_ctrl *lvts_ctrl;
+	int i, ret;
+
+	ret = lvts_ctrl_init(dev, lvts_td, lvts_data);
+	if (ret)
+		return ret;
+
+	ret = lvts_domain_reset(dev, lvts_td->reset);
+	if (ret) {
+		dev_dbg(dev, "Failed to reset domain");
+		return ret;
+	}
+
+	for (i = 0; i < lvts_td->num_lvts_ctrl; i++) {
+
+		lvts_ctrl = &lvts_td->lvts_ctrl[i];
+
+		/*
+		 * Initialization steps:
+		 *
+		 * - Enable the clock
+		 * - Connect to the LVTS
+		 * - Initialize the LVTS
+		 * - Prepare the calibration data
+		 * - Select monitored sensors
+		 * [ Configure sampling ]
+		 * [ Configure the interrupt ]
+		 * - Start measurement
+		 */
+		ret = lvts_ctrl_enable(dev, lvts_ctrl);
+		if (ret) {
+			dev_dbg(dev, "Failed to enable LVTS clock");
+			return ret;
+		}
+
+		ret = lvts_ctrl_connect(dev, lvts_ctrl);
+		if (ret) {
+			dev_dbg(dev, "Failed to connect to LVTS controller");
+			return ret;
+		}
+
+		ret = lvts_ctrl_initialize(dev, lvts_ctrl);
+		if (ret) {
+			dev_dbg(dev, "Failed to initialize controller");
+			return ret;
+		}
+
+		ret = lvts_ctrl_calibrate(dev, lvts_ctrl);
+		if (ret) {
+			dev_dbg(dev, "Failed to calibrate controller");
+			return ret;
+		}
+
+		ret = lvts_ctrl_configure(dev, lvts_ctrl);
+		if (ret) {
+			dev_dbg(dev, "Failed to configure controller");
+			return ret;
+		}
+
+		ret = lvts_ctrl_start(dev, lvts_ctrl);
+		if (ret) {
+			dev_dbg(dev, "Failed to start controller");
+			return ret;
+		}
+	}
+
+	return lvts_debugfs_init(dev, lvts_td);
+}
+
+static int lvts_probe(struct platform_device *pdev)
+{
+	struct lvts_data *lvts_data;

drivers/thermal/mediatek/lvts_thermal.c line 1127

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+	struct lvts_domain *lvts_td;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int irq, ret;
+
+	lvts_td = devm_kzalloc(dev, sizeof(*lvts_td), GFP_KERNEL);
+	if (!lvts_td)
+		return -ENOMEM;
+
+	lvts_data = (struct lvts_data *)of_device_get_match_data(dev);

Why do you need case?

Review

Quoted 2 lines
(quoted diff) +2 -0
+	if (!lvts_data) {
+		dev_dbg(dev, "No platforme 

Drop. How is it even possible?

drivers/thermal/mediatek/lvts_thermal.c line 1135

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+		return -ENODATA;
+	};
+
+	lvts_td->clk = devm_clk_get_enabled(dev, NULL);
+	if (IS_ERR(lvts_td->clk)) {
+		dev_dbg(dev, "Failed to retrieve clock\n");

Drop all debug statements. Either this is an error (so return dev_err_probe) or core handles messages.

drivers/thermal/mediatek/lvts_thermal.c line 1141

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+		return PTR_ERR(lvts_td->clk);
+	}
+
+	res = platform_get_mem_or_io(pdev, 0);
+	if (!res) {
+		dev_dbg(dev, "No IO resource\n");

Ditto

drivers/thermal/mediatek/lvts_thermal.c line 1145

Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+		return -ENXIO;
+	}
+
+	lvts_td->base = devm_ioremap_resource(dev, res);

Why not using single wrapper for this?

drivers/thermal/mediatek/lvts_thermal.c line 1147

Quoted 2 lines
drivers/thermal/mediatek/lvts_thermal.c new file +2 -0
+	if (IS_ERR(lvts_td->base)) {
+		dev_dbg(dev, "Failed to map io resource\n");

Ditto

drivers/thermal/mediatek/lvts_thermal.c line 1153

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+		return PTR_ERR(lvts_td->base);
+	}
+
+	lvts_td->reset = devm_reset_control_get_by_index(dev, 0);
+	if (IS_ERR(lvts_td->reset)) {
+		dev_dbg(dev, "Failed to get reset control\n");

Ditto

drivers/thermal/mediatek/lvts_thermal.c line 1159

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+		return PTR_ERR(lvts_td->reset);
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_dbg(dev, "No irq resource\n");

Ditto

drivers/thermal/mediatek/lvts_thermal.c line 1165

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+		return irq;
+	}
+
+	ret = lvts_domain_init(dev, lvts_td, lvts_data);
+	if (ret) {
+		dev_dbg(dev, "Failed to initialize the lvts domain\n");

Why this is debug?

drivers/thermal/mediatek/lvts_thermal.c line 1176

Quoted 11 lines
drivers/thermal/mediatek/lvts_thermal.c new file +11 -0
+		return ret;
+	}
+
+	/*
+	 * At this point the LVTS is initialized and enabled. We can
+	 * safely enable the interrupt.
+	 */
+	ret = devm_request_threaded_irq(dev, irq, NULL, lvts_irq_handler,
+					IRQF_ONESHOT, dev_name(dev), lvts_td);
+	if (ret) {
+		dev_dbg(dev, "Failed to request interrupt\n");

Ditto

Quoted 15 lines
drivers/thermal/mediatek/lvts_thermal.c new file +15 -0
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, lvts_td);
+
+	return 0;
+}
+
+static int lvts_remove(struct platform_device *pdev)
+{
+	struct lvts_domain *lvts_td;
+	struct device *dev = &pdev->dev;
+	int i;
+
+	lvts_td = platform_get_drvdata(pdev);

drivers/thermal/mediatek/lvts_thermal.c line 1201

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+
+	for (i = 0; i < lvts_td->num_lvts_ctrl; i++)
+		lvts_ctrl_disable(dev, &lvts_td->lvts_ctrl[i]);
+
+	lvts_debugfs_exit();
+
+	return 0;
+}
+
+static struct lvts_ctrl_data mt8195_lvts_data_ctrl[] = {

Why this cannot be const?

drivers/thermal/mediatek/lvts_thermal.c line 1212

Quoted 11 lines
drivers/thermal/mediatek/lvts_thermal.c new file +11 -0
+	{
+		.cal_offset = { 0x4, 0x7 },
+		.lvts_sensor = {
+			{ .dt_id = MT8195_MCU_BIG_CPU0 },
+			{ .dt_id = MT8195_MCU_BIG_CPU1 }
+		},
+		.num_lvts_sensor = 2,
+		.offset = 0x0,
+		.hw_tshut_temp = LVTS_HW_SHUTDOWN_MT8195,
+	},
+

Drop blank line

Review

Quoted 1 line
(quoted diff) +1 -0
+	{

Best regards,
Krzysztof

#40 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Hi Krzysztof,

Thank you very much for the review!

Quoted 20 lines · Krzysztof Kozlowski
Quoted 15 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

(...)

Quoted 16 lines
Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+struct lvts_domain {
+     struct lvts_ctrl *lvts_ctrl;
+     struct reset_control *reset;

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+     struct clk *clk;
+     int num_lvts_ctrl;
+     void __iomem *base;
+     size_t calib_len;
+     u8 *calib;
+};
+
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

This root node is the topmost directory for debugfs called 'lvts', the different driver instances are below this. It is a singleton.

Quoted 47 lines
Quoted 8 lines
drivers/thermal/mediatek/lvts_thermal.c new file +7 -0
+
+#define LVTS_DEBUG_FS_REGS(__reg)            \
+{                                            \
+     .name = __stringify(__reg),             \
+     .offset = __reg(0),                     \
+}
+

(...)

Quoted 36 lines
drivers/thermal/mediatek/lvts_thermal.c new file +36 -0
+
+static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
+{
+     struct lvts_sensor *lvts_sensor = tz->devdata;
+     void __iomem *base = lvts_sensor->base;
+     u32 raw_low = lvts_temp_to_raw(low);
+     u32 raw_high = lvts_temp_to_raw(high);
+
+     /*
+      * Hot to normal temperature threshold
+      *
+      * LVTS_H2NTHRE
+      *
+      * Bits:
+      *
+      * 14-0 : Raw temperature for threshold
+      */
+     if (low != -INT_MAX) {
+             dev_dbg(&tz->device, "Setting low limit temperature interrupt: %d\n", low);
+             writel(raw_low, LVTS_H2NTHRE(base));
+     }
+
+     /*
+      * Hot temperature threshold
+      *
+      * LVTS_HTHRE
+      *
+      * Bits:
+      *
+      * 14-0 : Raw temperature for threshold
+      */
+     dev_dbg(&tz->device, "Setting high limit temperature interrupt: %d\n", high);
+     writel(raw_high, LVTS_HTHRE(base));
+
+     return 0;
+}
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 334

Quoted 5 lines
drivers/thermal/mediatek/lvts_thermal.c new file +5 -0
+
+static irqreturn_t lvts_ctrl_irq_handler(struct lvts_ctrl *lvts_ctrl)
+{
+     irqreturn_t iret = IRQ_NONE;
+     u32 value, masks[] = {

Don't mix different types in one declaration. u32 and a pointer are quite different types.

I'm not sure to understand.
LVTS_INT_SENSORx are not pointers but register values.

Quoted 254 lines
Quoted 254 lines
drivers/thermal/mediatek/lvts_thermal.c new file +253 -0
+             LVTS_INT_SENSOR0,
+             LVTS_INT_SENSOR1,
+             LVTS_INT_SENSOR2,
+             LVTS_INT_SENSOR3
+     };
+     int i;
+
+     /*
+      * Interrupt monitoring status
+      *
+      * LVTS_MONINTST
+      *
+      * Bits:
+      *
+      * 31 : Interrupt for stage 3
+      * 30 : Interrupt for stage 2
+      * 29 : Interrupt for state 1
+      * 28 : Interrupt using filter on sensor 3
+      *
+      * 27 : Interrupt using immediate on sensor 3
+      * 26 : Interrupt normal to hot on sensor 3
+      * 25 : Interrupt high offset on sensor 3
+      * 24 : Interrupt low offset on sensor 3
+      *
+      * 23 : Interrupt hot threshold on sensor 3
+      * 22 : Interrupt cold threshold on sensor 3
+      * 21 : Interrupt using filter on sensor 2
+      * 20 : Interrupt using filter on sensor 1
+      *
+      * 19 : Interrupt using filter on sensor 0
+      * 18 : Interrupt using immediate on sensor 2
+      * 17 : Interrupt using immediate on sensor 1
+      * 16 : Interrupt using immediate on sensor 0
+      *
+      * 15 : Interrupt device access timeout interrupt
+      * 14 : Interrupt normal to hot on sensor 2
+      * 13 : Interrupt high offset interrupt on sensor 2
+      * 12 : Interrupt low offset interrupt on sensor 2
+      *
+      * 11 : Interrupt hot threshold on sensor 2
+      * 10 : Interrupt cold threshold on sensor 2
+      *  9 : Interrupt normal to hot on sensor 1
+      *  8 : Interrupt high offset interrupt on sensor 1
+      *
+      *  7 : Interrupt low offset interrupt on sensor 1
+      *  6 : Interrupt hot threshold on sensor 1
+      *  5 : Interrupt cold threshold on sensor 1
+      *  4 : Interrupt normal to hot on sensor 0
+      *
+      *  3 : Interrupt high offset interrupt on sensor 0
+      *  2 : Interrupt low offset interrupt on sensor 0
+      *  1 : Interrupt hot threshold on sensor 0
+      *  0 : Interrupt cold threshold on sensor 0
+      *
+      * We are interested in the sensor(s) responsible of the
+      * interrupt event. We update the thermal framework with the
+      * thermal zone associated with the sensor. The framework will
+      * take care of the rest whatever the kind of interrupt, we
+      * are only interested in which sensor raised the interrupt.
+      *
+      * sensor 3 interrupt: 0001 1111 1100 0000 0000 0000 0000 0000
+      *                  => 0x1FC00000
+      * sensor 2 interrupt: 0000 0000 0010 0100 0111 1100 0000 0000
+      *                  => 0x00247C00
+      * sensor 1 interrupt: 0000 0000 0001 0001 0000 0011 1110 0000
+      *                  => 0X000881F0
+      * sensor 0 interrupt: 0000 0000 0000 1001 0000 0000 0001 1111
+      *                  => 0x0009001F
+      */
+     value = readl(LVTS_MONINTSTS(lvts_ctrl->base));
+
+     /*
+      * Let's figure out which sensors raised the interrupt
+      *
+      * NOTE: the masks array must be ordered with the index
+      * corresponding to the sensor id eg. index=0, mask for
+      * sensor0.
+      */
+     for (i = 0; i < ARRAY_SIZE(masks); i++) {
+
+             if (!(value & masks[i]))
+                     continue;
+
+             thermal_zone_device_update(lvts_ctrl->sensors[i].tz,
+                                        THERMAL_TRIP_VIOLATED);
+             iret = IRQ_HANDLED;
+     }
+
+     /*
+      * Write back to clear the interrupt status (W1C)
+      */
+     writel(value, LVTS_MONINTSTS(lvts_ctrl->base));
+
+     return iret;
+}
+
+/*
+ * Temperature interrupt handler. Even if the driver supports more
+ * interrupt modes, we use the interrupt when the temperature crosses
+ * the hot threshold the way up and the way down (modulo the
+ * hysteresis).
+ *
+ * Each thermal domain has a couple of interrupts, one for hardware
+ * reset and another one for all the thermal events happening on the
+ * different sensors.
+ *
+ * The interrupt is configured for thermal events when crossing the
+ * hot temperature limit. At each interrupt, we check in every
+ * controller if there is an interrupt pending.
+ */
+static irqreturn_t lvts_irq_handler(int irq, void *data)
+{
+     struct lvts_domain *lvts_td = data;
+     irqreturn_t aux, iret = IRQ_NONE;
+     int i;
+
+     for (i = 0; i < lvts_td->num_lvts_ctrl; i++) {
+
+             aux = lvts_ctrl_irq_handler(lvts_td->lvts_ctrl);
+             if (aux != IRQ_HANDLED)
+                     continue;
+
+             iret = IRQ_HANDLED;
+     }
+
+     return iret;
+}
+
+static struct thermal_zone_device_ops lvts_ops = {
+     .get_temp = lvts_get_temp,
+     .set_trips = lvts_set_trips,
+};
+
+static int __init lvts_sensor_init(struct device *dev,
+                                struct lvts_ctrl *lvts_ctrl,
+                                struct lvts_ctrl_data *lvts_ctrl_data)
+{
+     struct lvts_sensor *lvts_sensor = lvts_ctrl->sensors;
+     void __iomem *msr_regs[] = {
+             LVTS_MSR0(lvts_ctrl->base),
+             LVTS_MSR1(lvts_ctrl->base),
+             LVTS_MSR2(lvts_ctrl->base),
+             LVTS_MSR3(lvts_ctrl->base)
+     };
+
+     void __iomem *imm_regs[] = {
+             LVTS_IMMD0(lvts_ctrl->base),
+             LVTS_IMMD1(lvts_ctrl->base),
+             LVTS_IMMD2(lvts_ctrl->base),
+             LVTS_IMMD3(lvts_ctrl->base)
+     };
+
+     int i;
+
+     for (i = 0; i < lvts_ctrl_data->num_lvts_sensor; i++) {
+
+             int dt_id = lvts_ctrl_data->lvts_sensor[i].dt_id;
+
+             /*
+              * At this point, we don't know which id matches which
+              * sensor. Let's set arbitrally the id from the index.
+              */
+             lvts_sensor[i].id = i;
+
+             /*
+              * The thermal zone registration will set the trip
+              * point interrupt in the thermal controller
+              * register. But this one will be reset in the
+              * initialization after. So we need to post pone the
+              * thermal zone creation after the controller is
+              * setup. For this reason, we store the device tree
+              * node id from the data in the sensor structure
+              */
+             lvts_sensor[i].dt_id = dt_id;
+
+             /*
+              * We assign the base address of the thermal
+              * controller as a back pointer. So it will be
+              * accessible from the different thermal framework ops
+              * as we pass the lvts_sensor pointer as thermal zone
+              * private data.
+              */
+             lvts_sensor[i].base = lvts_ctrl->base;
+
+             /*
+              * Each sensor has its own register address to read from.
+              */
+             lvts_sensor[i].msr = lvts_ctrl_data->mode == LVTS_MSR_IMMEDIATE_MODE ?
+                     imm_regs[i] : msr_regs[i];
+     };
+
+     lvts_ctrl->num_lvts_sensor = lvts_ctrl_data->num_lvts_sensor;
+
+     return 0;
+}
+
+/*
+ * The efuse blob values follows the sensor enumeration per thermal
+ * controller. The decoding of the stream is as follow:
+ *
+ *                        <--?-> <----big0 ???---> <-sensor0-> <-0->
+ *                        ------------------------------------------
+ * index in the stream: : | 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 |
+ *                        ------------------------------------------
+ *
+ *                        <--sensor1--><-0-> <----big1 ???---> <-sen
+ *                        ------------------------------------------
+ *                        | 0x7 | 0x8 | 0x9 | 0xA | 0xB | OxC | OxD |
+ *                        ------------------------------------------
+ *
+ *                        sor0-> <-0-> <-sensor1-> <-0-> ..........
+ *                        ------------------------------------------
+ *                        | 0x7 | 0x8 | 0x9 | 0xA | 0xB | OxC | OxD |
+ *                        ------------------------------------------
+ *
+ * And so on ...
+ *
+ * The data description gives the offset of the calibration data in
+ * this bytes stream for each sensor.
+ *
+ * Each thermal controller can handle up to 4 sensors max, we don't
+ * care if there are less as the array of calibration is sized to 4
+ * anyway. The unused sensor slot will be zeroed.
+ */
+static int __init lvts_calibration_init(struct device *dev,
+                                     struct lvts_ctrl *lvts_ctrl,
+                                     struct lvts_ctrl_data *lvts_ctrl_data,
+                                     u8 *efuse_calibration)
+{
+     int i;
+
+     for (i = 0; i < lvts_ctrl_data->num_lvts_sensor; i++)
+             memcpy(&lvts_ctrl->calibration[i],
+                    efuse_calibration + lvts_ctrl_data->cal_offset[i], 2);
+
+     return 0;
+}
+
+/*
+ * The efuse bytes stream can be split into different chunk of
+ * nvmems. This function reads and concatenate those into a single
+ * buffer so it can be read sequentially when initializing the
+ * calibration data.
+ */
+static int lvts_calibration_read(struct device *dev, struct lvts_domain *lvts_td,
+                              struct lvts_data *lvts_data)
+{
+     struct device_node *np = dev_of_node(dev);
+     struct nvmem_cell *cell;
+     struct property *prop;
+     const char *cell_name;
+
+     of_property_for_each_string(np, "nvmem-cell-names", prop, cell_name) {
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 593

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+             size_t len;
+             u8 *efuse;
+
+             cell = of_nvmem_cell_get(np, cell_name);
+             if (IS_ERR(cell)) {
+                     dev_dbg(dev, "Failed to get cell '%s'\n", cell_name);

Is this an error? If so, why debug? dbg is not for errors.

AFAIK using dev_dbg does not increase ELF size when DEBUG is disabled. If this is not a good reason for you, then I will change it to dev_err.

Quoted 23 lines
Quoted 23 lines
drivers/thermal/mediatek/lvts_thermal.c new file +22 -0
+                     return PTR_ERR(cell);
+             }
+
+             efuse = nvmem_cell_read(cell, &len);
+
+             nvmem_cell_put(cell);
+
+             if (IS_ERR(efuse)) {
+                     dev_dbg(dev, "Failed to read cell '%s'\n", cell_name);
+                     return PTR_ERR(efuse);
+             }
+
+             lvts_td->calib = devm_krealloc(dev, lvts_td->calib,
+                                            lvts_td->calib_len + len, GFP_KERNEL);
+             if (!lvts_td->calib)
+                     return -ENOMEM;
+
+             memcpy(lvts_td->calib + lvts_td->calib_len, efuse, len);
+
+             lvts_td->calib_len += len;
+
+             kfree(efuse);
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 621

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+     }
+
+     return 0;
+}
+
+static int __init lvts_golden_temp_init(struct device *dev, u32 *value)

You did not test it, right? Build with section mismatch analysis...

I'm not sure to fully understand this comment.
Would you explain, please?

Quoted 17 lines
Quoted 5 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+{
+     u32 gt;
+
+     gt = (*value) >> 24;

drivers/thermal/mediatek/lvts_thermal.c line 635

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+
+     if (gt && gt < LVTS_GOLDEN_TEMP_MAX)
+             golden_temp = gt;
+
+     coeff_b = golden_temp * 500 + LVTS_COEFF_B;
+
+     return 0;
+}
+
+static int __init lvts_ctrl_init(struct device *dev,

Same problem.

Would you explain, please?

Quoted 9 lines
Quoted 8 lines
drivers/thermal/mediatek/lvts_thermal.c new file +7 -0
+                              struct lvts_domain *lvts_td,
+                              struct lvts_data *lvts_data)
+{
+     size_t size = sizeof(*lvts_td->lvts_ctrl) * lvts_data->num_lvts_ctrl;
+     struct lvts_ctrl *lvts_ctrl;
+     int i, ret;
+
Quoted 6 lines

drivers/thermal/mediatek/lvts_thermal.c line 792

Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+static inline int lvts_ctrl_enable(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+     return lvts_ctrl_set_enable(lvts_ctrl, 1);

Drop the wrapper, it's useless. true or false for enable are quite obvious.

OK.

Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 797

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +5 -0
+}
+
+static inline int lvts_ctrl_disable(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+     return lvts_ctrl_set_enable(lvts_ctrl, 0);

Drop the wrapper.

OK.

Quoted 325 lines
Quoted 325 lines
drivers/thermal/mediatek/lvts_thermal.c new file +324 -0
+}
+
+static int lvts_ctrl_connect(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+     u32 id, cmds[] = { 0xC103FFFF, 0xC502FF55 };
+
+     lvts_write_config(lvts_ctrl, cmds, ARRAY_SIZE(cmds));
+
+     /*
+      * LVTS_ID : Get ID and status of the thermal controller
+      *
+      * Bits:
+      *
+      * 0-5  : thermal controller id
+      *   7  : thermal controller connection is valid
+      */
+     id = readl(LVTS_ID(lvts_ctrl->base));
+     if (!(id & BIT(7)))
+             return -EIO;
+
+     return 0;
+}
+
+static int lvts_ctrl_initialize(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+     /*
+      * Write device mask: 0xC1030000
+      */
+     u32 cmds[] = {
+             0xC1030E01, 0xC1030CFC, 0xC1030A8C, 0xC103098D, 0xC10308F1,
+             0xC10307A6, 0xC10306B8, 0xC1030500, 0xC1030420, 0xC1030300,
+             0xC1030030, 0xC10300F6, 0xC1030050, 0xC1030060, 0xC10300AC,
+             0xC10300FC, 0xC103009D, 0xC10300F1, 0xC10300E1
+     };
+
+     lvts_write_config(lvts_ctrl, cmds, ARRAY_SIZE(cmds));
+
+     return 0;
+}
+
+static int lvts_ctrl_calibrate(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+     int i;
+     void __iomem *lvts_edata[] = {
+             LVTS_EDATA00(lvts_ctrl->base),
+             LVTS_EDATA01(lvts_ctrl->base),
+             LVTS_EDATA02(lvts_ctrl->base),
+             LVTS_EDATA03(lvts_ctrl->base)
+     };
+
+     /*
+      * LVTS_EDATA0X : Efuse calibration reference value for sensor X
+      *
+      * Bits:
+      *
+      * 20-0 : Efuse value for normalization data
+      */
+     for (i = 0; i < LVTS_SENSOR_MAX; i++)
+             writel(lvts_ctrl->calibration[i], lvts_edata[i]);
+
+     return 0;
+}
+
+static int lvts_ctrl_configure(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+     u32 value;
+
+     /*
+      * LVTS_TSSEL : Sensing point index numbering
+      *
+      * Bits:
+      *
+      * 31-24: ADC Sense 3
+      * 23-16: ADC Sense 2
+      * 15-8 : ADC Sense 1
+      * 7-0  : ADC Sense 0
+      */
+     value = LVTS_TSSEL_CONF;
+     writel(value, LVTS_TSSEL(lvts_ctrl->base));
+
+     /*
+      * LVTS_CALSCALE : ADC voltage round
+      */
+     value = 0x300;
+     value = LVTS_CALSCALE_CONF;
+
+     /*
+      * LVTS_MSRCTL0 : Sensor filtering strategy
+      *
+      * Filters:
+      *
+      * 000 : One sample
+      * 001 : Avg 2 samples
+      * 010 : 4 samples, drop min and max, avg 2 samples
+      * 011 : 6 samples, drop min and max, avg 4 samples
+      * 100 : 10 samples, drop min and max, avg 8 samples
+      * 101 : 18 samples, drop min and max, avg 16 samples
+      *
+      * Bits:
+      *
+      * 0-2  : Sensor0 filter
+      * 3-5  : Sensor1 filter
+      * 6-8  : Sensor2 filter
+      * 9-11 : Sensor3 filter
+      */
+     value = LVTS_HW_FILTER << 9 |  LVTS_HW_FILTER << 6 |
+                     LVTS_HW_FILTER << 3 | LVTS_HW_FILTER;
+     writel(value, LVTS_MSRCTL0(lvts_ctrl->base));
+
+     /*
+      * LVTS_MSRCTL1 : Measurement control
+      *
+      * Bits:
+      *
+      * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3
+      * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2
+      * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1
+      * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0
+      *
+      * That configuration will ignore the filtering and the delays
+      * introduced below in MONCTL1 and MONCTL2
+      */
+     if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) {
+             value = BIT(9) | BIT(6) | BIT(5) | BIT(4);
+             writel(value, LVTS_MSRCTL1(lvts_ctrl->base));
+     }
+
+     /*
+      * LVTS_MONCTL1 : Period unit and group interval configuration
+      *
+      * The clock source of LVTS thermal controller is 26MHz.
+      *
+      * The period unit is a time base for all the interval delays
+      * specified in the registers. By default we use 12. The time
+      * conversion is done by multiplying by 256 and 1/26.10^6
+      *
+      * An interval delay multiplied by the period unit gives the
+      * duration in seconds.
+      *
+      * - Filter interval delay is a delay between two samples of
+      * the same sensor.
+      *
+      * - Sensor interval delay is a delay between two samples of
+      * different sensors.
+      *
+      * - Group interval delay is a delay between different rounds.
+      *
+      * For example:
+      *     If Period unit = C, filter delay = 1, sensor delay = 2, group delay = 1,
+      *     and two sensors, TS1 and TS2, are in a LVTS thermal controller
+      *     and then
+      *     Period unit time = C * 1/26M * 256 = 12 * 38.46ns * 256 = 118.149us
+      *     Filter interval delay = 1 * Period unit = 118.149us
+      *     Sensor interval delay = 2 * Period unit = 236.298us
+      *     Group interval delay = 1 * Period unit = 118.149us
+      *
+      *     TS1    TS1 ... TS1    TS2    TS2 ... TS2    TS1...
+      *        <--> Filter interval delay
+      *                       <--> Sensor interval delay
+      *                                             <--> Group interval delay
+      * Bits:
+      *      29 - 20 : Group interval
+      *      16 - 13 : Send a single interrupt when crossing the hot threshold (1)
+      *                or an interrupt everytime the hot threshold is crossed (0)
+      *       9 - 0  : Period unit
+      *
+      */
+     value = LVTS_GROUP_INTERVAL << 20 | LVTS_PERIOD_UNIT;
+     writel(value, LVTS_MONCTL1(lvts_ctrl->base));
+
+     /*
+      * LVTS_MONCTL2 : Filtering and sensor interval
+      *
+      * Bits:
+      *
+      *      25-16 : Interval unit in PERIOD_UNIT between sample on
+      *              the same sensor, filter interval
+      *       9-0  : Interval unit in PERIOD_UNIT between each sensor
+      *
+      */
+     value = LVTS_FILTER_INTERVAL << 16 | LVTS_SENSOR_INTERVAL;
+     writel(value, LVTS_MONCTL2(lvts_ctrl->base));
+
+     return lvts_irq_init(lvts_ctrl);
+}
+
+static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl)
+{
+     struct lvts_sensor *lvts_sensors = lvts_ctrl->sensors;
+     struct thermal_zone_device *tz;
+     u32 sensor_map = 0;
+     int i;
+
+     for (i = 0; i < lvts_ctrl->num_lvts_sensor; i++) {
+
+             int dt_id = lvts_sensors[i].dt_id;
+
+             tz = devm_thermal_of_zone_register(dev, dt_id, &lvts_sensors[i],
+                                                &lvts_ops);
+             if (IS_ERR(tz)) {
+                     /*
+                      * This thermal zone is not described in the
+                      * device tree. It is not an error from the
+                      * thermal OF code POV, we just continue.
+                      */
+                     if (PTR_ERR(tz) == -ENODEV)
+                             continue;
+
+                     return PTR_ERR(tz);
+             }
+
+             /*
+              * The thermal zone pointer will be needed in the
+              * interrupt handler, we store it in the sensor
+              * structure. The thermal domain structure will be
+              * passed to the interrupt handler private data as the
+              * interrupt is shared for all the controller
+              * belonging to the thermal domain.
+              */
+             lvts_sensors[i].tz = tz;
+
+             /*
+              * This sensor was correctly associated with a thermal
+              * zone, let's set the corresponding bit in the sensor
+              * map, so we can enable the temperature monitoring in
+              * the hardware thermal controller.
+              */
+             sensor_map |= BIT(i);
+     }
+
+     /*
+      * Bits:
+      *      9: Single point access flow
+      *    0-3: Enable sensing point 0-3
+      *
+      * The initialization of the thermal zones give us
+      * which sensor point to enable. If any thermal zone
+      * was not described in the device tree, it won't be
+      * enabled here in the sensor map.
+      */
+     writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base));
+
+     return 0;
+}
+
+static int lvts_domain_init(struct device *dev, struct lvts_domain *lvts_td,
+                         struct lvts_data *lvts_data)
+{
+     struct lvts_ctrl *lvts_ctrl;
+     int i, ret;
+
+     ret = lvts_ctrl_init(dev, lvts_td, lvts_data);
+     if (ret)
+             return ret;
+
+     ret = lvts_domain_reset(dev, lvts_td->reset);
+     if (ret) {
+             dev_dbg(dev, "Failed to reset domain");
+             return ret;
+     }
+
+     for (i = 0; i < lvts_td->num_lvts_ctrl; i++) {
+
+             lvts_ctrl = &lvts_td->lvts_ctrl[i];
+
+             /*
+              * Initialization steps:
+              *
+              * - Enable the clock
+              * - Connect to the LVTS
+              * - Initialize the LVTS
+              * - Prepare the calibration data
+              * - Select monitored sensors
+              * [ Configure sampling ]
+              * [ Configure the interrupt ]
+              * - Start measurement
+              */
+             ret = lvts_ctrl_enable(dev, lvts_ctrl);
+             if (ret) {
+                     dev_dbg(dev, "Failed to enable LVTS clock");
+                     return ret;
+             }
+
+             ret = lvts_ctrl_connect(dev, lvts_ctrl);
+             if (ret) {
+                     dev_dbg(dev, "Failed to connect to LVTS controller");
+                     return ret;
+             }
+
+             ret = lvts_ctrl_initialize(dev, lvts_ctrl);
+             if (ret) {
+                     dev_dbg(dev, "Failed to initialize controller");
+                     return ret;
+             }
+
+             ret = lvts_ctrl_calibrate(dev, lvts_ctrl);
+             if (ret) {
+                     dev_dbg(dev, "Failed to calibrate controller");
+                     return ret;
+             }
+
+             ret = lvts_ctrl_configure(dev, lvts_ctrl);
+             if (ret) {
+                     dev_dbg(dev, "Failed to configure controller");
+                     return ret;
+             }
+
+             ret = lvts_ctrl_start(dev, lvts_ctrl);
+             if (ret) {
+                     dev_dbg(dev, "Failed to start controller");
+                     return ret;
+             }
+     }
+
+     return lvts_debugfs_init(dev, lvts_td);
+}
+
+static int lvts_probe(struct platform_device *pdev)
+{
+     struct lvts_data *lvts_data;
+     struct lvts_domain *lvts_td;
+     struct device *dev = &pdev->dev;
+     struct resource *res;
+     int irq, ret;
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 1127

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+
+     lvts_td = devm_kzalloc(dev, sizeof(*lvts_td), GFP_KERNEL);
+     if (!lvts_td)
+             return -ENOMEM;
+
+     lvts_data = (struct lvts_data *)of_device_get_match_data(dev);

Why do you need case?

Would you explain, please?

Quoted 5 lines

Review

Quoted 3 lines
(quoted diff) +2 -0
+     if (!lvts_data) {
+             dev_dbg(dev, "No platforme

Drop. How is it even possible?

OK,
All "dev_dbg" in "probe" function will be replaced by "dev_err_probe"

Quoted 10 lines

drivers/thermal/mediatek/lvts_thermal.c line 1135

Quoted 7 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+             return -ENODATA;
+     };
+
+     lvts_td->clk = devm_clk_get_enabled(dev, NULL);
+     if (IS_ERR(lvts_td->clk)) {
+             dev_dbg(dev, "Failed to retrieve clock\n");

Drop all debug statements. Either this is an error (so return dev_err_probe) or core handles messages.

I will change it to dev_err_probe.

Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 1141

Quoted 7 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+             return PTR_ERR(lvts_td->clk);
+     }
+
+     res = platform_get_mem_or_io(pdev, 0);
+     if (!res) {
+             dev_dbg(dev, "No IO resource\n");
Quoted 8 lines

Ditto

drivers/thermal/mediatek/lvts_thermal.c line 1145

Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+             return -ENXIO;
+     }
+
+     lvts_td->base = devm_ioremap_resource(dev, res);

Why not using single wrapper for this?

OK,
I will chnagne it to "lvts_td->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);"

Quoted 5 lines

drivers/thermal/mediatek/lvts_thermal.c line 1147

Quoted 3 lines
drivers/thermal/mediatek/lvts_thermal.c new file +2 -0
+     if (IS_ERR(lvts_td->base)) {
+             dev_dbg(dev, "Failed to map io resource\n");

Ditto

I will change it to dev_err_probe.

Quoted 9 lines

drivers/thermal/mediatek/lvts_thermal.c line 1153

Quoted 7 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+             return PTR_ERR(lvts_td->base);
+     }
+
+     lvts_td->reset = devm_reset_control_get_by_index(dev, 0);
+     if (IS_ERR(lvts_td->reset)) {
+             dev_dbg(dev, "Failed to get reset control\n");

Ditto

I will change it to dev_err_probe.

Quoted 9 lines

drivers/thermal/mediatek/lvts_thermal.c line 1159

Quoted 7 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+             return PTR_ERR(lvts_td->reset);
+     }
+
+     irq = platform_get_irq(pdev, 0);
+     if (irq < 0) {
+             dev_dbg(dev, "No irq resource\n");

Ditto

I will change it to dev_err_probe.

Quoted 9 lines

drivers/thermal/mediatek/lvts_thermal.c line 1165

Quoted 7 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+             return irq;
+     }
+
+     ret = lvts_domain_init(dev, lvts_td, lvts_data);
+     if (ret) {
+             dev_dbg(dev, "Failed to initialize the lvts domain\n");

Why this is debug?

I will change it to dev_err_probe.

Quoted 13 lines

drivers/thermal/mediatek/lvts_thermal.c line 1176

Quoted 12 lines
drivers/thermal/mediatek/lvts_thermal.c new file +11 -0
+             return ret;
+     }
+
+     /*
+      * At this point the LVTS is initialized and enabled. We can
+      * safely enable the interrupt.
+      */
+     ret = devm_request_threaded_irq(dev, irq, NULL, lvts_irq_handler,
+                                     IRQF_ONESHOT, dev_name(dev), lvts_td);
+     if (ret) {
+             dev_dbg(dev, "Failed to request interrupt\n");
Quoted 1 line

Ditto

I will change it to dev_err_probe.

Quoted 20 lines
Quoted 20 lines
drivers/thermal/mediatek/lvts_thermal.c new file +19 -0
+             return ret;
+     }
+
+     platform_set_drvdata(pdev, lvts_td);
+
+     return 0;
+}
+
+static int lvts_remove(struct platform_device *pdev)
+{
+     struct lvts_domain *lvts_td;
+     struct device *dev = &pdev->dev;
+     int i;
+
+     lvts_td = platform_get_drvdata(pdev);
+
+     for (i = 0; i < lvts_td->num_lvts_ctrl; i++)
+             lvts_ctrl_disable(dev, &lvts_td->lvts_ctrl[i]);
+
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 1201

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+     lvts_debugfs_exit();
+
+     return 0;
+}
+
+static struct lvts_ctrl_data mt8195_lvts_data_ctrl[] = {

Why this cannot be const?

I've got the following warning when I added "const" drivers/thermal/mediatek/lvts_thermal.c:1286:27: warning:
initialization discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
1286 | .lvts_ctrl = mt8195_lvts_data_ctrl,

      |                           ^~~~~~~~~~~~~~~~~~~~~~~~~

Still working on it.
Any suggestion will be helpful, thanks!

Quoted 13 lines

drivers/thermal/mediatek/lvts_thermal.c line 1212

Quoted 12 lines
drivers/thermal/mediatek/lvts_thermal.c new file +11 -0
+     {
+             .cal_offset = { 0x4, 0x7 },
+             .lvts_sensor = {
+                     { .dt_id = MT8195_MCU_BIG_CPU0 },
+                     { .dt_id = MT8195_MCU_BIG_CPU1 }
+             },
+             .num_lvts_sensor = 2,
+             .offset = 0x0,
+             .hw_tshut_temp = LVTS_HW_SHUTDOWN_MT8195,
+     },
+
Quoted 1 line

Drop blank line

OK,
I will do the same for other blank lines.

Quoted 6 lines
Quoted 2 lines

+ {

Best regards,
Krzysztof

Best regards,
Balsam.

maintainer
#41 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Quoted 10 lines · Balsam CHIHI

Hi Krzysztof,

Thank you very much for the review!

Quoted 4 lines · Krzysztof Kozlowski
Quoted 2 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

[...]

Quoted 9 lines
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 334

Quoted 5 lines
drivers/thermal/mediatek/lvts_thermal.c new file +5 -0
+
+static irqreturn_t lvts_ctrl_irq_handler(struct lvts_ctrl *lvts_ctrl)
+{
+     irqreturn_t iret = IRQ_NONE;
+     u32 value, masks[] = {

Don't mix different types in one declaration. u32 and a pointer are quite different types.

Quoted 3 lines

I'm not sure to understand.
LVTS_INT_SENSORx are not pointers but register values.

u32 mask[] is a pointer to a array of u32 values of undefined length.

[...]

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

+static int __init lvts_golden_temp_init(struct device *dev, u32 *value)

You did not test it, right? Build with section mismatch analysis...

I'm not sure to fully understand this comment.
Would you explain, please?

AFAIU:

lvts_golden_temp_init() and lvts_ctrl_init() are called from a function that is not in __init section:
lvts_domain_init()

So if you free up the first to functions after init but not the callers, things can explote.

[...]

Quoted 17 lines
Quoted 8 lines
Quoted 8 lines
drivers/thermal/mediatek/lvts_thermal.c new file +8 -0
+
+static int lvts_probe(struct platform_device *pdev)
+{
+     struct lvts_data *lvts_data;
+     struct lvts_domain *lvts_td;
+     struct device *dev = &pdev->dev;
+     struct resource *res;
+     int irq, ret;
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 1127

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+
+     lvts_td = devm_kzalloc(dev, sizeof(*lvts_td), GFP_KERNEL);
+     if (!lvts_td)
+             return -ENOMEM;
+
+     lvts_data = (struct lvts_data *)of_device_get_match_data(dev);

Why do you need case?

Quoted 2 lines

Would you explain, please?

Typo by Krysztof, he meant the cast.
lvts_data = of_device_get_match_data(dev);
should be good enough.

Regards,
Matthias

#42 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Hi Matthias,

Quoted 26 lines · Matthias Brugger
Quoted 10 lines · Balsam CHIHI

Hi Krzysztof,

Thank you very much for the review!

Quoted 4 lines · Krzysztof Kozlowski
Quoted 2 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

[...]

Quoted 9 lines
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 334

Quoted 5 lines
drivers/thermal/mediatek/lvts_thermal.c new file +5 -0
+
+static irqreturn_t lvts_ctrl_irq_handler(struct lvts_ctrl *lvts_ctrl)
+{
+     irqreturn_t iret = IRQ_NONE;
+     u32 value, masks[] = {

Don't mix different types in one declaration. u32 and a pointer are quite different types.

Quoted 6 lines
Quoted 3 lines

I'm not sure to understand.
LVTS_INT_SENSORx are not pointers but register values.

u32 mask[] is a pointer to a array of u32 values of undefined length.

I will change this to :
u32 value;
u32 masks[] = {

Quoted 10 lines

[...]

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

+static int __init lvts_golden_temp_init(struct device *dev, u32 *value)

You did not test it, right? Build with section mismatch analysis...

I'm not sure to fully understand this comment.
Would you explain, please?

Quoted 9 lines

AFAIU:

lvts_golden_temp_init() and lvts_ctrl_init() are called from a function that is not in __init section:
lvts_domain_init()

So if you free up the first to functions after init but not the callers, things can explote.

__init will be removed for all functions.

Quoted 19 lines

[...]

Quoted 17 lines
Quoted 16 lines
Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+static int lvts_probe(struct platform_device *pdev)
+{
+     struct lvts_data *lvts_data;

drivers/thermal/mediatek/lvts_thermal.c line 1127

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+     struct lvts_domain *lvts_td;
+     struct device *dev = &pdev->dev;
+     struct resource *res;
+     int irq, ret;
+
+     lvts_td = devm_kzalloc(dev, sizeof(*lvts_td), GFP_KERNEL);
+     if (!lvts_td)
+             return -ENOMEM;
+
+     lvts_data = (struct lvts_data *)of_device_get_match_data(dev);

Why do you need case?

Quoted 7 lines
Quoted 2 lines

Would you explain, please?

Typo by Krysztof, he meant the cast.
lvts_data = of_device_get_match_data(dev);
should be good enough.

OK,
It will be like you suggested.

Quoted 2 lines

Regards,
Matthias

Thank you for the review!

Best regards,
Balsam

#43 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

In reply to Balsam CHIHI
Quoted 8 lines · Balsam CHIHI
Quoted 5 lines

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 3 lines
drivers/thermal/mediatek/lvts_thermal.c new file +3 -0
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

This root node is the topmost directory for debugfs called 'lvts', the different driver instances are below this. It is a singleton.

Indeed. What about removal? Aren't you remobing entire directory structure on first device removal?

(...)

Quoted 11 lines
Quoted 10 lines

drivers/thermal/mediatek/lvts_thermal.c line 593

Quoted 8 lines
drivers/thermal/mediatek/lvts_thermal.c new file +8 -0
+
+     of_property_for_each_string(np, "nvmem-cell-names", prop, cell_name) {
+             size_t len;
+             u8 *efuse;
+
+             cell = of_nvmem_cell_get(np, cell_name);
+             if (IS_ERR(cell)) {
+                     dev_dbg(dev, "Failed to get cell '%s'\n", cell_name);

Is this an error? If so, why debug? dbg is not for errors.

Quoted 2 lines

AFAIK using dev_dbg does not increase ELF size when DEBUG is disabled. If this is not a good reason for you, then I will change it to dev_err.

But also dev_dbg are not visible in error or warn level logs. If this is not an error, then indeed dev_dbg could be fine. But errors should be verbose.

Quoted 33 lines
Quoted 24 lines
Quoted 24 lines
drivers/thermal/mediatek/lvts_thermal.c new file +22 -0
+                     return PTR_ERR(cell);
+             }
+
+             efuse = nvmem_cell_read(cell, &len);
+
+             nvmem_cell_put(cell);
+
+             if (IS_ERR(efuse)) {
+                     dev_dbg(dev, "Failed to read cell '%s'\n", cell_name);
+                     return PTR_ERR(efuse);
+             }
+
+             lvts_td->calib = devm_krealloc(dev, lvts_td->calib,
+                                            lvts_td->calib_len + len, GFP_KERNEL);
+             if (!lvts_td->calib)
+                     return -ENOMEM;
+
+             memcpy(lvts_td->calib + lvts_td->calib_len, efuse, len);
+
+             lvts_td->calib_len += len;
+
+             kfree(efuse);
Quoted 8 lines

drivers/thermal/mediatek/lvts_thermal.c line 621

Quoted 6 lines
drivers/thermal/mediatek/lvts_thermal.c new file +6 -0
+     }
+
+     return 0;
+}
+
+static int __init lvts_golden_temp_init(struct device *dev, u32 *value)

You did not test it, right? Build with section mismatch analysis...

Quoted 2 lines

I'm not sure to fully understand this comment.
Would you explain, please?

git grep -i "section mismatch" leads to lib/Kconfig.debug and DEBUG_SECTION_MISMATCH

(...)

Quoted 10 lines
Quoted 3 lines
Quoted 1 line

+static struct lvts_ctrl_data mt8195_lvts_data_ctrl[] = {

Why this cannot be const?

I've got the following warning when I added "const" drivers/thermal/mediatek/lvts_thermal.c:1286:27: warning:
initialization discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
1286 | .lvts_ctrl = mt8195_lvts_data_ctrl,

      |                           ^~~~~~~~~~~~~~~~~~~~~~~~~

As with every const... Do you need lvts_ctrl to be non-const? If yes, then how do you handle multiple devices (singleton)?

Best regards,
Krzysztof

#44 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Hi Krzysztof,

Quoted 8 lines · Krzysztof Kozlowski
Quoted 6 lines · Balsam CHIHI
Quoted 5 lines

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 3 lines
drivers/thermal/mediatek/lvts_thermal.c new file +3 -0
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

Quoted 6 lines
Quoted 2 lines

This root node is the topmost directory for debugfs called 'lvts', the different driver instances are below this. It is a singleton.

Indeed. What about removal? Aren't you remobing entire directory structure on first device removal?

For now, the driver only supports one instance.
I will find a way to handle this when the driver supports more instances. Is this suggestion OK for you?

Quoted 13 lines

(...)

Quoted 11 lines
Quoted 10 lines

drivers/thermal/mediatek/lvts_thermal.c line 593

Quoted 8 lines
drivers/thermal/mediatek/lvts_thermal.c new file +8 -0
+
+     of_property_for_each_string(np, "nvmem-cell-names", prop, cell_name) {
+             size_t len;
+             u8 *efuse;
+
+             cell = of_nvmem_cell_get(np, cell_name);
+             if (IS_ERR(cell)) {
+                     dev_dbg(dev, "Failed to get cell '%s'\n", cell_name);

Is this an error? If so, why debug? dbg is not for errors.

Quoted 6 lines
Quoted 2 lines

AFAIK using dev_dbg does not increase ELF size when DEBUG is disabled. If this is not a good reason for you, then I will change it to dev_err.

But also dev_dbg are not visible in error or warn level logs. If this is not an error, then indeed dev_dbg could be fine. But errors should be verbose.

OK,
I will replace all "dev_dbg" with "dev_err" in this function.

Quoted 34 lines
Quoted 34 lines
Quoted 33 lines
Quoted 21 lines
drivers/thermal/mediatek/lvts_thermal.c new file +18 -0
+                     return PTR_ERR(cell);
+             }
+
+             efuse = nvmem_cell_read(cell, &len);
+
+             nvmem_cell_put(cell);
+
+             if (IS_ERR(efuse)) {
+                     dev_dbg(dev, "Failed to read cell '%s'\n", cell_name);
+                     return PTR_ERR(efuse);
+             }
+
+             lvts_td->calib = devm_krealloc(dev, lvts_td->calib,
+                                            lvts_td->calib_len + len, GFP_KERNEL);
+             if (!lvts_td->calib)
+                     return -ENOMEM;
+
+             memcpy(lvts_td->calib + lvts_td->calib_len, efuse, len);

drivers/thermal/mediatek/lvts_thermal.c line 621

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+
+             lvts_td->calib_len += len;
+
+             kfree(efuse);
+     }
+
+     return 0;
+}
+
+static int __init lvts_golden_temp_init(struct device *dev, u32 *value)

You did not test it, right? Build with section mismatch analysis...

Quoted 5 lines
Quoted 2 lines

I'm not sure to fully understand this comment.
Would you explain, please?

git grep -i "section mismatch" leads to lib/Kconfig.debug and DEBUG_SECTION_MISMATCH

__init is removed from all functions.

Quoted 14 lines

(...)

Quoted 10 lines
Quoted 3 lines
Quoted 1 line

+static struct lvts_ctrl_data mt8195_lvts_data_ctrl[] = {

Why this cannot be const?

I've got the following warning when I added "const" drivers/thermal/mediatek/lvts_thermal.c:1286:27: warning:
initialization discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
1286 | .lvts_ctrl = mt8195_lvts_data_ctrl,

      |                           ^~~~~~~~~~~~~~~~~~~~~~~~~
Quoted 3 lines

As with every const... Do you need lvts_ctrl to be non-const? If yes, then how do you handle multiple devices (singleton)?

I found a fix for this it was simple.
add const here as you suggested
and in other function parameters every time we use this variable.

Quoted 3 lines

Best regards,
Krzysztof

Thank you for the review!

Best regards,
Balsam

#45 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

In reply to Krzysztof Kozlowski
Quoted 19 lines · Krzysztof Kozlowski
Quoted 15 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

(...)

Quoted 16 lines
Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+struct lvts_domain {
+	struct lvts_ctrl *lvts_ctrl;
+	struct reset_control *reset;

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+	struct clk *clk;
+	int num_lvts_ctrl;
+	void __iomem *base;
+	size_t calib_len;
+	u8 *calib;
+};
+
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

For now, we can put the entry in /sys/kernel/debug/<dev_name>

I'm preparing a debugfs series for the thermal framework and that will provide an entry to hook in for the sensors debugfs if available

#46 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Quoted 37 lines · Daniel Lezcano
Quoted 19 lines · Krzysztof Kozlowski
Quoted 15 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

(...)

Quoted 16 lines
Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+struct lvts_domain {
+	struct lvts_ctrl *lvts_ctrl;
+	struct reset_control *reset;

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+	struct clk *clk;
+	int num_lvts_ctrl;
+	void __iomem *base;
+	size_t calib_len;
+	u8 *calib;
+};
+
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

Quoted 4 lines

For now, we can put the entry in /sys/kernel/debug/<dev_name>

I'm preparing a debugfs series for the thermal framework and that will provide an entry to hook in for the sensors debugfs if available

The code looked like it does not support it at all. I think it would remove entries from second instance, while unbinding the first (or the opposite).

Best regards,
Krzysztof

#47 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

Quoted 38 lines · Krzysztof Kozlowski
Quoted 37 lines · Daniel Lezcano
Quoted 35 lines · Krzysztof Kozlowski
Quoted 15 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

(...)

Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+struct lvts_domain {
+	struct lvts_ctrl *lvts_ctrl;
+	struct reset_control *reset;

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+	struct clk *clk;
+	int num_lvts_ctrl;
+	void __iomem *base;
+	size_t calib_len;
+	u8 *calib;
+};
+
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

Quoted 8 lines
Quoted 4 lines

For now, we can put the entry in /sys/kernel/debug/<dev_name>

I'm preparing a debugfs series for the thermal framework and that will provide an entry to hook in for the sensors debugfs if available

The code looked like it does not support it at all. I think it would remove entries from second instance, while unbinding the first (or the opposite).

Yes, and you are right.

So instead of having:

/sys/kernel/debugfs/lvts/lvts@mcu

We will have:

/sys/kernel/debugfs/lvts@mcu

Later, when the other domain is added, we will have:

/sys/kernel/debugfs/lvts@mcu
/sys/kernel/debugfs/lvts@ap

Each instance takes care of removing its own entry

When I'll introduce thermal debugfs, I'll take care of massaging the driver to have them like:

/sys/kernel/debugfs/thermal/thermal_zone/0/sensors/lvts@mcu,0 /sys/kernel/debugfs/thermal/thermal_zone/1/sensors/lvts@ap,1

Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#48 lore raw

Re: [PATCH v12] thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver

In reply to Daniel Lezcano

Hi Daniel,

Quoted 38 lines · Daniel Lezcano
Quoted 19 lines · Krzysztof Kozlowski
Quoted 15 lines · On 31/01/2023 16:38, [email protected] wrote:

From: Balsam CHIHI <[email protected]>

The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.

A thermal domains can be the MCU or the AP.

Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.

The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.

(...)

Quoted 16 lines
Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c new file +4 -0
+
+struct lvts_domain {
+   struct lvts_ctrl *lvts_ctrl;
+   struct reset_control *reset;

drivers/thermal/mediatek/lvts_thermal.c line 134

Quoted 10 lines
drivers/thermal/mediatek/lvts_thermal.c new file +10 -0
+   struct clk *clk;
+   int num_lvts_ctrl;
+   void __iomem *base;
+   size_t calib_len;
+   u8 *calib;
+};
+
+#ifdef CONFIG_MTK_LVTS_THERMAL_DEBUGFS
+
+static struct dentry *root;

How do you handle two instances of driver?

Quoted 1 line

For now, we can put the entry in /sys/kernel/debug/<dev_name>

Yes, sure.
I will do the necessary changes.

Quoted 3 lines

I'm preparing a debugfs series for the thermal framework and that will provide an entry to hook in for the sensors debugfs if available

It would be a good feature!
good luck!

Best regards,
Balsam.

#49 lore raw

PATCH v11 5/6 arm64/dts/mt8195: Add thermal zones and thermal nodes

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

Add thermal zones and thermal nodes for the mt8195.

---
 arch/arm64/boot/dts/mediatek/mt8195.dtsi | 129 +++++++++++++++++++++++
 1 file changed, 129 insertions(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +129 -0
index 09df105f4606..636676f4ba25 100644
@@ -14,6 +14,7 @@
 #include <dt-bindings/pinctrl/mt8195-pinfunc.h>
 #include <dt-bindings/power/mt8195-power.h>
 #include <dt-bindings/reset/mt8195-resets.h>
+#include <dt-bindings/thermal/mediatek-lvts.h>
 
 / {
 	compatible = "mediatek,mt8195";
@@ -954,6 +955,17 @@ spi0: spi@1100a000 {
 			status = "disabled";
 		};
 
+		lvts_ap: thermal-sensor@1100b000 {
+			compatible = "mediatek,mt8195-lvts-ap";
+			reg = <0 0x1100b000 0 0x1000>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+			resets = <&infracfg_ao MT8195_INFRA_RST0_THERM_CTRL_SWRST>;
+			nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+			nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+			#thermal-sensor-cells = <1>;
+		};
+
 		spi1: spi@11010000 {
 			compatible = "mediatek,mt8195-spi",
 				     "mediatek,mt6765-spi";
@@ -1114,6 +1126,17 @@ mmc2: mmc@11250000 {
 			status = "disabled";
 		};
 
+		lvts_mcu: thermal-sensor@11278000 {
+			compatible = "mediatek,mt8195-lvts-mcu";
+			reg = <0 0x11278000 0 0x1000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+			resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+			nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+			nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+			#thermal-sensor-cells = <1>;
+		};
+
 		xhci1: usb@11290000 {
 			compatible = "mediatek,mt8195-xhci",
 				     "mediatek,mtk-xhci";
@@ -2387,4 +2410,110 @@ dp_tx: dp-tx@1c600000 {
 			status = "disabled";
 		};
 	};
+
+	thermal_zones: thermal-zones {
+		cpu0-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+			trips {
+				cpu0_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU1>;
+			trips {
+				cpu1_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU2>;
+			trips {
+				cpu2_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU3>;
+			trips {
+				cpu3_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu4-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU0>;
+			trips {
+				cpu4_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu5-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU1>;
+			trips {
+				cpu5_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu6-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU2>;
+			trips {
+				cpu6_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu7-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU3>;
+			trips {
+				cpu7_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
 };
Signature · 1 line
2.34.1
maintainer Reviewed-by on v11 5/6
#50 lore raw

Re: [PATCH v11 5/6] arm64/dts/mt8195: Add thermal zones and thermal nodes

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 5 lines

From: Balsam CHIHI <[email protected]>

Add thermal zones and thermal nodes for the mt8195.

You should change the commit title to reflect the same syntax that you can find in a git log --oneline arch/arm64/boot/dts/mediatek/.

arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes

or

arm64: dts: mt8195: Add thermal zones and thermal nodes

...otherwise:

#51 lore raw

Re: [PATCH v11 5/6] arm64/dts/mt8195: Add thermal zones and thermal nodes

Quoted 8 lines · AngeloGioacchino Del Regno

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 5 lines

From: Balsam CHIHI <[email protected]>

Add thermal zones and thermal nodes for the mt8195.

Quoted 9 lines

You should change the commit title to reflect the same syntax that you can find in a git log --oneline arch/arm64/boot/dts/mediatek/.

arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes

or

arm64: dts: mt8195: Add thermal zones and thermal nodes

Hi Angelo,

Thank you for the review.
Should I resend with the fix?
Or you would fix it when applying it like Matthias did for "[PATCH v11 3/6] arm64/dts/mt8195: Add efuse node to mt8195"?

Best regards,
Balsam

Quoted 5 lines

...otherwise:

maintainer
#52 lore raw

Re: [PATCH v11 5/6] arm64/dts/mt8195: Add thermal zones and thermal nodes

Quoted 20 lines · Balsam CHIHI
Quoted 8 lines · AngeloGioacchino Del Regno

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 5 lines

From: Balsam CHIHI <[email protected]>

Add thermal zones and thermal nodes for the mt8195.

Quoted 9 lines

You should change the commit title to reflect the same syntax that you can find in a git log --oneline arch/arm64/boot/dts/mediatek/.

arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes

or

arm64: dts: mt8195: Add thermal zones and thermal nodes

Quoted 7 lines

Hi Angelo,

Thank you for the review.
Should I resend with the fix?
Or you would fix it when applying it like Matthias did for "[PATCH v11 3/6] arm64/dts/mt8195: Add efuse node to mt8195"?

If you need to send a new version for any reason, then please update. Otherwise I'll fix it once I can take it.

Regards,
Matthias

#53 lore raw

Re: [PATCH v11 5/6] arm64/dts/mt8195: Add thermal zones and thermal nodes

Quoted 26 lines · Matthias Brugger
Quoted 22 lines · Balsam CHIHI
Quoted 8 lines · AngeloGioacchino Del Regno

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 5 lines

From: Balsam CHIHI <[email protected]>

Add thermal zones and thermal nodes for the mt8195.

Quoted 9 lines

You should change the commit title to reflect the same syntax that you can find in a git log --oneline arch/arm64/boot/dts/mediatek/.

arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes

or

arm64: dts: mt8195: Add thermal zones and thermal nodes

Hi Angelo,

Quoted 8 lines
Quoted 5 lines

Thank you for the review.
Should I resend with the fix?
Or you would fix it when applying it like Matthias did for "[PATCH v11 3/6] arm64/dts/mt8195: Add efuse node to mt8195"?

If you need to send a new version for any reason, then please update. Otherwise I'll fix it once I can take it.

Hi Matthias,

OK.
I appreciate it,
thank you.

Best regards,
Balsam

Quoted 3 lines

Regards,
Matthias

#54 lore raw

PATCH v12 1/1 arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

Add thermal zones and thermal nodes for the mt8195.

---
Changelog:
v12:
- Fixed subject prefix
- Rename "include/dt-bindings/thermal/mediatek-lvts.h" to "include/dt-bindings/thermal/mediatek,lvts-thermal.h" due to this patch
https://lore.kernel.org/all/[email protected]/
---

---
 arch/arm64/boot/dts/mediatek/mt8195.dtsi | 129 +++++++++++++++++++++++
 1 file changed, 129 insertions(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +129 -0
index 09df105f4606..c7e958f8f1b5 100644
@@ -14,6 +14,7 @@
 #include <dt-bindings/pinctrl/mt8195-pinfunc.h>
 #include <dt-bindings/power/mt8195-power.h>
 #include <dt-bindings/reset/mt8195-resets.h>
+#include <dt-bindings/thermal/mediatek,lvts-thermal.h>
 
 / {
 	compatible = "mediatek,mt8195";
@@ -954,6 +955,17 @@ spi0: spi@1100a000 {
 			status = "disabled";
 		};
 
+		lvts_ap: thermal-sensor@1100b000 {
+			compatible = "mediatek,mt8195-lvts-ap";
+			reg = <0 0x1100b000 0 0x1000>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+			resets = <&infracfg_ao MT8195_INFRA_RST0_THERM_CTRL_SWRST>;
+			nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+			nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+			#thermal-sensor-cells = <1>;
+		};
+
 		spi1: spi@11010000 {
 			compatible = "mediatek,mt8195-spi",
 				     "mediatek,mt6765-spi";
@@ -1114,6 +1126,17 @@ mmc2: mmc@11250000 {
 			status = "disabled";
 		};
 
+		lvts_mcu: thermal-sensor@11278000 {
+			compatible = "mediatek,mt8195-lvts-mcu";
+			reg = <0 0x11278000 0 0x1000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_THERM>;
+			resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>;
+			nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>;
+			nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2";
+			#thermal-sensor-cells = <1>;
+		};
+
 		xhci1: usb@11290000 {
 			compatible = "mediatek,mt8195-xhci",
 				     "mediatek,mtk-xhci";
@@ -2387,4 +2410,110 @@ dp_tx: dp-tx@1c600000 {
 			status = "disabled";
 		};
 	};
+
+	thermal_zones: thermal-zones {
+		cpu0-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+			trips {
+				cpu0_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU1>;
+			trips {
+				cpu1_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU2>;
+			trips {
+				cpu2_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU3>;
+			trips {
+				cpu3_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu4-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU0>;
+			trips {
+				cpu4_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu5-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU1>;
+			trips {
+				cpu5_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu6-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU2>;
+			trips {
+				cpu6_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu7-thermal {
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU3>;
+			trips {
+				cpu7_crit: trip-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
 };
Signature · 1 line
2.34.1
#55 lore raw

PATCH v11 6/6 arm64/dts/mt8195: Add temperature mitigation threshold

In reply to [email protected]

From: Balsam CHIHI <[email protected]>

The mt8195 SoC has several hotspots around the CPUs. Specify the targeted temperature threshold when to apply the mitigation and define the associated cooling devices.

---
 arch/arm64/boot/dts/mediatek/mt8195.dtsi | 169 ++++++++++++++++++++---
 1 file changed, 153 insertions(+), 16 deletions(-)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +153 -16
index 636676f4ba25..9544ae91379a 100644
@@ -14,6 +14,7 @@
 #include <dt-bindings/pinctrl/mt8195-pinfunc.h>
 #include <dt-bindings/power/mt8195-power.h>
 #include <dt-bindings/reset/mt8195-resets.h>
+#include <dt-bindings/thermal/thermal.h>
 #include <dt-bindings/thermal/mediatek-lvts.h>
 
 / {
@@ -2413,107 +2414,243 @@ dp_tx: dp-tx@1c600000 {
 
 	thermal_zones: thermal-zones {
 		cpu0-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>;
+
 			trips {
+				cpu0_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu0_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu0_alert>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu1-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU1>;
+
 			trips {
+				cpu1_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu1_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu1_alert>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu2-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU2>;
+
 			trips {
+				cpu2_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu2_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu2_alert>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu3-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU3>;
+
 			trips {
+				cpu3_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu3_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu3_alert>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu4-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU0>;
+
 			trips {
+				cpu4_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu4_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu4_alert>;
+					cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu5-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU1>;
+
 			trips {
+				cpu5_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu5_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu5_alert>;
+					cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu6-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU2>;
+
 			trips {
+				cpu6_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu6_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu6_alert>;
+					cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		cpu7-thermal {
-			polling-delay = <0>;
-			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
 			thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU3>;
+
 			trips {
+				cpu7_alert: trip-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
 				cpu7_crit: trip-crit {
 					temperature = <100000>;
 					hysteresis = <2000>;
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu7_alert>;
+					cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+								<&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 };
Signature · 1 line
2.34.1
maintainer Reviewed-by on v11 6/6
#56 lore raw

Re: [PATCH v11 6/6] arm64/dts/mt8195: Add temperature mitigation threshold

Il 24/01/23 14:17, [email protected] ha scritto:

Quoted 7 lines

From: Balsam CHIHI <[email protected]>

The mt8195 SoC has several hotspots around the CPUs. Specify the targeted temperature threshold when to apply the mitigation and define the associated cooling devices.

Commit title prefix
- arm64: dts: mt8195:
or
- arm64: dts: mediatek: mt8195:

otherwise,