Skip to contentSkip to conversation

ppc_4xx-ld: u-boot: Not enough room for program headers (allocated 2, need 3)

U-Boot-Users 腾飞龙 2 participants 3 messages Jan 3, 2006

lore
Share & tools
lore

腾飞龙

author
#0 lore raw

Hi ,
Thank you so much for answering my questions i mentioned several days ago.
I'm porting u-boot-1.1.4 to Ebedded planet EP405(with ppc 405GPr
processor) and it bases on a similar board CPCI4052 as you suggested. i did as follow

    #cd ../u-boot-1.1.3/board/esd
    #mkdir ep405
    #cd cpci405
    #cp *  ../ep405
    #cd  ../ep405
    # mv cpci405.c ep405.c
    #cd ../../../include/configs
    #cp CPCI4052.h  ep405.h
   then add text content as follow to u-boot-1.1.3/Makefile
   ep_config:	unconfig
	@./mkconfig $(@:_config=) ppc ppc4xx cpci405 esd
	@echo "BOARD_REVISION = $(@:_config=)"	>>include/config.mk
    #cd ../u-boot-1.1.3
    #make distclean
    #make ep405_config
    #make all
    then the error appears:

ppc_4xx-ld: u-boot: Not enough room for program headers (allocated 2, need 3)
ppc_4xx-ld: final link failed: Bad value
would you please tell me why and how to handle it ?
Thank u and best wishes !

#1 lore raw
Quoted 5 lines · In message <[email protected]> you wrote:

Thank you so much for answering my questions i mentioned several days =
ago.
I'm porting u-boot-1.1.4 to Ebedded planet EP405(with ppc 405GPr
processor) and it bases on a similar board CPCI4052 as you suggested.

Let's keep in mind that similar does not mean the same.

Quoted 2 lines
    #cd ../u-boot-1.1.3/board/esd
    #mkdir ep405

This is wrong. Don't do this. "board/esd" is for boards manufactured by esd electronics only, while the EP405 is by Embedded Planet. So far we don't have a vendor directory for EP, which means you have to place your code in board/

Quoted 3 lines

then add text content as follow to u-boot-1.1.3/Makefile
ep_config: unconfig

	@./mkconfig $(@:_config=) ppc ppc4xx cpci405 esd

Wrong again, as you must provide your own board config file instead of using the cpci405 one.

Quoted 1 line

would you please tell me why and how to handle it ?

Clean up above problems first, please.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Things that try to look like things often do look  more  like  things
than things. Well-known fact.       - Terry Pratchett, _Wyrd Sisters_
author
#2 lore raw

Thank u!
I just want to make a test before i modify content of files such as ep405.c .
and i changed the directory as you said to board/ and modified the Makefile correctly.
then ,
#make clean
#make ep405_config
#make all
the error followed is :
make[1]: Entering directory /tmp/u-boot-1.1.4/board/ep405' make[1]: *** No rule to make target ../common/misc.c', needed by
`.depend'. Stop.

so now, where will i check the rule and do some amendments and how to do?

I also confused by another problem: There has been a PlanetCore Boot
Loader resides in flash memoery(in EP405),and there is no JTAG on the board. so if i erase the existed bootloader which is convinient for writing flash, it will be difficult for me to write my u-boot image to flash.
so can i keep the existed bootloader and as it is now and use it to
write u-boot in another region of the flash ? Then after booting from PlanetCore Boot Loader, i will be able to run u-boot and check if it has been correctly modified.
if the answer is yes, what should i do during the procedure of
modifying u-boot?

2006/1/3, Wolfgang Denk <[email protected]>:

Quoted 39 lines
Quoted 2 lines · In message <[email protected]> you wrote:

Thank you so much for answering my questions i mentioned several days

=

Quoted 3 lines

ago.
I'm porting u-boot-1.1.4 to Ebedded planet EP405(with ppc 405GPr
processor) and it bases on a similar board CPCI4052 as you suggested.

Let's keep in mind that similar does not mean the same.

Quoted 2 lines
    #cd ../u-boot-1.1.3/board/esd
    #mkdir ep405

This is wrong. Don't do this. "board/esd" is for boards manufactured by esd electronics only, while the EP405 is by Embedded Planet. So far we don't have a vendor directory for EP, which means you have to place your code in board/

Quoted 3 lines

then add text content as follow to u-boot-1.1.3/Makefile
ep_config: unconfig

	@./mkconfig $(@:_config=) ppc ppc4xx cpci405 esd

Wrong again, as you must provide your own board config file instead of using the cpci405 one.

Quoted 1 line

would you please tell me why and how to handle it ?

Clean up above problems first, please.

Best regards,

Wolfgang Denk

--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Things that try to look like things often do look more like things
than things. Well-known fact. - Terry Pratchett, _Wyrd Sisters_