board: Add support for iMX8MN BSH SMM S2 PRO
PATCH v3 1/1 board: Add support for iMX8MN BSH SMM S2 PRO
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
- Uboot 2022-01-rc1 (reference tree)
- Default packages from buildroot
https://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro as co-maintainer, we work together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314
---
Changes V2->V3:
- Update the uboot download point
- Add feedback from Heiko Thiery <[email protected]>
- Add feddback from Giulio Benetti
Changes V1->V2:
- add the board reference page
- test with docker
- adjust the buildroot config in order to use buildman
--- DEVELOPERS | 2 ++ board/bsh/bsh-imx8mn/extlinux.conf | 4 +++ board/bsh/bsh-imx8mn/genimage.cfg | 17 +++++++++ board/bsh/bsh-imx8mn/post-build.sh | 7 ++++ board/bsh/bsh-imx8mn/post-image.sh | 3 ++ board/bsh/bsh-imx8mn/readme.txt | 55 ++++++++++++++++++++++++++++++ configs/bsh_smms2pro_defconfig | 43 +++++++++++++++++++++++ 7 files changed, 131 insertions(+) create mode 100644 board/bsh/bsh-imx8mn/extlinux.conf create mode 100644 board/bsh/bsh-imx8mn/genimage.cfg create mode 100755 board/bsh/bsh-imx8mn/post-build.sh create mode 100755 board/bsh/bsh-imx8mn/post-image.sh create mode 100644 board/bsh/bsh-imx8mn/readme.txt create mode 100644 configs/bsh_smms2pro_defconfig
DEVELOPERS +2 -0
@@ -220,6 +220,7 @@ F: configs/snps_archs38_hsdk_defconfig F: configs/snps_archs38_vdk_defconfig N: Ariel D'Alessandro <[email protected]> +F: board/bsh/ F: package/axfsutils/ F: package/mali-t76x/
@@ -2018,6 +2019,7 @@ F: package/python-crc16/ F: package/python-pyzmq/ N: Michael Trimarchi <[email protected]> +F: board/bsh/ F: package/python-spidev/ N: Michael Vetter <[email protected]>
board/bsh/bsh-imx8mn/extlinux.conf new file +4 -0
@@ -0,0 +1,4 @@ +label buildroot + kernel /boot/Image + devicetree /boot/freescale/imx8mn-bsh-smm-s2pro.dtb + append root=PARTUUID=%PARTUUID% rootwait rw
board/bsh/bsh-imx8mn/genimage.cfg new file +17 -0
@@ -0,0 +1,17 @@ +image sdcard.img { + hdimage { + partition-table-type = "gpt" + } + + partition imx-boot { + in-partition-table = "no" + image = "flash.bin" + offset = 33K + } + + partition rootfs { + offset = 8M + image = "rootfs.ext4" + partition-uuid = %PARTUUID% + } +}
board/bsh/bsh-imx8mn/post-build.sh new file +7 -0
@@ -0,0 +1,7 @@ +#!/bin/sh +BOARD_DIR="$(dirname $0)" +PARTUUID="$($HOST_DIR/bin/uuidgen)" + +install -d "$TARGET_DIR/boot/extlinux/" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/extlinux.conf" > "$TARGET_DIR/boot/extlinux/extlinux.conf" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/genimage.cfg" > "$BINARIES_DIR/genimage.cfg"
board/bsh/bsh-imx8mn/post-image.sh new file +3 -0
@@ -0,0 +1,3 @@ +#!/bin/sh + +support/scripts/genimage.sh -c ${BINARIES_DIR}/genimage.cfg
board/bsh/bsh-imx8mn/readme.txt new file +55 -0
55 lines not on this page · raw message
configs/bsh_smms2pro_defconfig new file +43 -0
43 lines not on this page · raw message
Signature · 6 lines
2.25.1 _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot
Hi Michael, all,
Quoted 14 lines · Michael Trimarchi
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
- Uboot 2022-01-rc1 (reference tree)
- Default packages from buildroothttps://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro as co-maintainer, we work together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314
Quoted 6 lines
Cc Ariel D'Alessandro <[email protected]>Cc Jagan Teki <[email protected]>Cc Heiko Thiery <[email protected]>Cc Giulio Benetti <[email protected]>Reviewed-by Giulio Benetti <[email protected]>Signed-off-by Michael Trimarchi <[email protected]>
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot
Hi all
Should I need to resend? anything is missing now?
Michael
Quoted 26 lines · Ariel D'Alessandro
Hi Michael, all,
Quoted 14 lines · Michael Trimarchi
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
- Uboot 2022-01-rc1 (reference tree)
- Default packages from buildroothttps://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro as co-maintainer, we work together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314Quoted 6 lines
Cc Ariel D'Alessandro <[email protected]>Cc Jagan Teki <[email protected]>Cc Heiko Thiery <[email protected]>Cc Giulio Benetti <[email protected]>Reviewed-by Giulio Benetti <[email protected]>Signed-off-by Michael Trimarchi <[email protected]>Tested-by Ariel D'Alessandro <[email protected]>
Signature · 15 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot
Hi Michael,
Quoted 5 lines
Il giorno 12 feb 2022, alle ore 11:12, Michael Nazzareno Trimarchi <[email protected]> ha scritto:
Hi all
Should I need to resend? anything is missing now?
No, only need to wait until maintainers submit it or find something I haven’t found(hope not).
Best regards
Giulio
Quoted 23 lines
Michael
Quoted 20 lines
On Mon, Jan 31, 2022 at 5:20 PM Ariel D'Alessandro <[email protected]> wrote:
Hi Michael, all,
Quoted 15 lines · Michael Trimarchi
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
- Uboot 2022-01-rc1 (reference tree)
- Default packages from buildroothttps://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro as co-maintainer, we work together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314
Quoted 23 lines
Quoted 8 lines
Quoted 6 lines
Cc Ariel D'Alessandro <[email protected]>Cc Jagan Teki <[email protected]>Cc Heiko Thiery <[email protected]>Cc Giulio Benetti <[email protected]>Reviewed-by Giulio Benetti <[email protected]>Signed-off-by Michael Trimarchi <[email protected]>Tested-by Ariel D'Alessandro <[email protected]>Signature · 11 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot
Quoted 3 lines · Michael Trimarchi
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
I'm a bit uncomfortable to add an -rc version. But I guess it can be updated
as soon as 5.17 is released.
Quoted 17 lines
- Uboot 2022-01-rc1 (reference tree)
- Default packages from buildroothttps://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro as co-maintainer, we work together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314Cc Ariel D'Alessandro <[email protected]>Cc Jagan Teki <[email protected]>Cc Heiko Thiery <[email protected]>Cc Giulio Benetti <[email protected]>Reviewed-by Giulio Benetti <[email protected]>Signed-off-by Michael Trimarchi <[email protected]>
[snip]
DEVELOPERS F: configs/snps_archs38_hsdk_defconfig · line 223
Quoted 9 lines
DEVELOPERS +1
-0@@ -220,6 +220,7 @@ F: configs/snps_archs38_hsdk_defconfig F: configs/snps_archs38_vdk_defconfig N: Ariel D'Alessandro <[email protected]> +F: board/bsh/
You should also add configs/bsh_smms2pro_defconfig here.
Quoted 50 lines
DEVELOPERS +1
-0F: package/axfsutils/ F: package/mali-t76x/@@ -2018,6 +2019,7 @@ F: package/python-crc16/ F: package/python-pyzmq/ N: Michael Trimarchi <[email protected]> +F: board/bsh/ F: package/python-spidev/ N: Michael Vetter <[email protected]>board/bsh/bsh-imx8mn/extlinux.conf new file +4
-0@@ -0,0 +1,4 @@ +label buildroot + kernel /boot/Image + devicetree /boot/freescale/imx8mn-bsh-smm-s2pro.dtb + append root=PARTUUID=%PARTUUID% rootwait rwboard/bsh/bsh-imx8mn/genimage.cfg new file +17
-0@@ -0,0 +1,17 @@ +image sdcard.img { + hdimage { + partition-table-type = "gpt" + } + + partition imx-boot { + in-partition-table = "no" + image = "flash.bin" + offset = 33K + } + + partition rootfs { + offset = 8M + image = "rootfs.ext4" + partition-uuid = %PARTUUID% + } +}board/bsh/bsh-imx8mn/post-build.sh new file +0
-0
board/bsh/bsh-imx8mn/post-build.sh line 7
Quoted 7 lines
board/bsh/bsh-imx8mn/post-build.sh new file +7
-0@@ -0,0 +1,7 @@ +#!/bin/sh +BOARD_DIR="$(dirname $0)" +PARTUUID="$($HOST_DIR/bin/uuidgen)" + +install -d "$TARGET_DIR/boot/extlinux/" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/extlinux.conf" > "$TARGET_DIR/boot/extlinux/extlinux.conf" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/genimage.cfg" > "$BINARIES_DIR/genimage.cfg"
This is really a great way of doing it!
Quoted 46 lines
board/bsh/bsh-imx8mn/post-image.sh new file +3
-0@@ -0,0 +1,3 @@ +#!/bin/sh + +support/scripts/genimage.sh -c ${BINARIES_DIR}/genimage.cfgboard/bsh/bsh-imx8mn/readme.txt new file +31
-0@@ -0,0 +1,55 @@ +How to build it +=============== + +Configure buildroot: + + $ make bsh_smms2pro_defconfig + +Change settings to fit your needs (optional): + + $ make menuconfig + +Compile everything and buildr the rootfs image: + + $ make + + +Result of the build +=================== + +After building, the output/images directory contains: + + output/images/ + ├── bl31.bin + ├── Image + ├── flash.bin + ├── ddr3* + ├── rootfs.ext2 + ├── rootfs.ext4 -> rootfs.ext2 + ├── rootfs.tar + ├── sdcard.img + ├── u-boot.bin
board/bsh/bsh-imx8mn/readme.txt line 41
Quoted 10 lines
board/bsh/bsh-imx8mn/readme.txt new file +10
-0+ ├── u-boot-nodtb.bin + └── u-boot-spl.bin + + +Flashing the emmc card image +========================== + +To install the image on on eMMC + + $ sudo uuu -b emmc_all output/images/flash.bin output/images/sdcard.img
Please also explain where you get uuu. Can we build it as part of buildroot?
Then refer to it as output/host/bin/uuu.
Quoted 20 lines
board/bsh/bsh-imx8mn/readme.txt new file +14
-0+ + +Preparing the board +=================== + + * Connect a serial line to the board + * Power-up the board + + +Booting the board +================= + +By default the bootloader will search for the first valid image, starting +with the internal eMMC.configs/bsh_smms2pro_defconfig new file +0
-0
configs/bsh_smms2pro_defconfig line 1
Quoted 1 line
configs/bsh_smms2pro_defconfig new file +1
-0@@ -0,0 +1,43 @@ +BR2_aarch64=y
Even if the default happens to be correct, I prefer the subarch to be
specified explicitly. That way we can change the default later without affecting this defconfig.
configs/bsh_smms2pro_defconfig line 5
Quoted 4 lines
configs/bsh_smms2pro_defconfig new file +4
-0+BR2_TARGET_GENERIC_GETTY_PORT="ttymxc3" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/bsh/bsh-imx8mn/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="board/bsh/bsh-imx8mn/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="${UBOOT_DIR}/arch/arm/dts/imx8mn-bsh-smm-s2pro.dtb"
I may be missing something, but this doesn't seem to be used by any of the
post- scripts?
configs/bsh_smms2pro_defconfig line 9
Quoted 4 lines
configs/bsh_smms2pro_defconfig new file +4
-0+BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git" +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="v5.17-rc1"
Please use the tarball instead. Simply setting CUSTOM_VERSION should be
sufficient - if not, linux.mk has tobe fixed.
Quoted 12 lines
configs/bsh_smms2pro_defconfig new file +12
-0+BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mn-bsh-smm-s2pro" +BR2_LINUX_KERNEL_DTB_KEEP_DIRNAME=y +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y +BR2_PACKAGE_FREESCALE_IMX=y +BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8MN=y +BR2_PACKAGE_FIRMWARE_IMX=y +BR2_PACKAGE_FIRMWARE_IMX_DDR3=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y
configs/bsh_smms2pro_defconfig line 31
Quoted 10 lines
configs/bsh_smms2pro_defconfig new file +10
-0+BR2_TARGET_ROOTFS_EXT2_SIZE="120M" +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.5" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mn" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="IMX_BOOT_UART_BASE=0x30a60000" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_GIT=y +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://gitlab.apertis.org/adalessandro/u-boot.git"
Gitlab is able to generate tarballs as well. There are plenty of examples in
the tree.
I would normally fix these things up while applying, but since I'm not
entirely sure about merging a -rc kernel anyway, I'll wait for a v4 instead.
Oh, one more thing: the subject for a new defconfig is typically
"configs/bsh_smms2pro_defconfig: new defconfig"
Regards,
Arnout
configs/bsh_smms2pro_defconfig line 43
Quoted 12 lines
configs/bsh_smms2pro_defconfig new file +12
-0+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="v2022.01-bsh-smm2" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mn_bsh_smm_s2pro" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_PYTHON3=y +BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y +BR2_TARGET_UBOOT_NEEDS_OPENSSL=y +BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y +BR2_TARGET_UBOOT_NEEDS_IMX_FIRMWARE=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="flash.bin" +BR2_TARGET_UBOOT_SPL=y +BR2_PACKAGE_HOST_GENIMAGE=y
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot
Hi
Quoted 10 lines · Arnout Vandecappelle
Quoted 3 lines · Michael Trimarchi
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
I'm a bit uncomfortable to add an -rc version. But I guess it can be updated
as soon as 5.17 is released.
Ok, I will then wait
Quoted 82 lines
Quoted 18 lines
- Uboot 2022-01-rc1 (reference tree)
- Default packages from buildroothttps://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro as co-maintainer, we work together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314Cc Ariel D'Alessandro <[email protected]>Cc Jagan Teki <[email protected]>Cc Heiko Thiery <[email protected]>Cc Giulio Benetti <[email protected]>Reviewed-by Giulio Benetti <[email protected]>Signed-off-by Michael Trimarchi <[email protected]>[snip]
DEVELOPERS F: configs/snps_archs38_hsdk_defconfig · line 223
Quoted 9 lines
DEVELOPERS +1
-0@@ -220,6 +220,7 @@ F: configs/snps_archs38_hsdk_defconfig F: configs/snps_archs38_vdk_defconfig N: Ariel D'Alessandro <[email protected]> +F: board/bsh/You should also add configs/bsh_smms2pro_defconfig here.
Quoted 51 lines
DEVELOPERS +1
-0F: package/axfsutils/ F: package/mali-t76x/@@ -2018,6 +2019,7 @@ F: package/python-crc16/ F: package/python-pyzmq/ N: Michael Trimarchi <[email protected]> +F: board/bsh/ F: package/python-spidev/ N: Michael Vetter <[email protected]>board/bsh/bsh-imx8mn/extlinux.conf new file +4
-0@@ -0,0 +1,4 @@ +label buildroot + kernel /boot/Image + devicetree /boot/freescale/imx8mn-bsh-smm-s2pro.dtb + append root=PARTUUID=%PARTUUID% rootwait rwboard/bsh/bsh-imx8mn/genimage.cfg new file +17
-0@@ -0,0 +1,17 @@ +image sdcard.img { + hdimage { + partition-table-type = "gpt" + } + + partition imx-boot { + in-partition-table = "no" + image = "flash.bin" + offset = 33K + } + + partition rootfs { + offset = 8M + image = "rootfs.ext4" + partition-uuid = %PARTUUID% + } +}board/bsh/bsh-imx8mn/post-build.sh new file +1
-0@@ -0,0 +1,7 @@ +#!/bin/sh
Quoted 9 lines
board/bsh/bsh-imx8mn/post-build.sh line 7
Quoted 6 lines
board/bsh/bsh-imx8mn/post-build.sh new file +6
-0+BOARD_DIR="$(dirname $0)" +PARTUUID="$($HOST_DIR/bin/uuidgen)" + +install -d "$TARGET_DIR/boot/extlinux/" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/extlinux.conf" > "$TARGET_DIR/boot/extlinux/extlinux.conf" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/genimage.cfg" > "$BINARIES_DIR/genimage.cfg"This is really a great way of doing it!
Well, I have taken from another submitted board
Quoted 51 lines
Quoted 51 lines
board/bsh/bsh-imx8mn/post-image.sh new file +3
-0@@ -0,0 +1,3 @@ +#!/bin/sh + +support/scripts/genimage.sh -c ${BINARIES_DIR}/genimage.cfgboard/bsh/bsh-imx8mn/readme.txt new file +36
-0@@ -0,0 +1,55 @@ +How to build it +=============== + +Configure buildroot: + + $ make bsh_smms2pro_defconfig + +Change settings to fit your needs (optional): + + $ make menuconfig + +Compile everything and buildr the rootfs image: + + $ make + + +Result of the build +=================== + +After building, the output/images directory contains: + + output/images/ + ├── bl31.bin + ├── Image + ├── flash.bin + ├── ddr3* + ├── rootfs.ext2 + ├── rootfs.ext4 -> rootfs.ext2 + ├── rootfs.tar + ├── sdcard.img + ├── u-boot.bin + ├── u-boot-nodtb.bin + └── u-boot-spl.bin + + +Flashing the emmc card image
Quoted 8 lines
board/bsh/bsh-imx8mn/readme.txt line 41
Quoted 5 lines
board/bsh/bsh-imx8mn/readme.txt new file +5
-0+========================== + +To install the image on on eMMC + + $ sudo uuu -b emmc_all output/images/flash.bin output/images/sdcard.imgPlease also explain where you get uuu. Can we build it as part of buildroot?
Then refer to it as output/host/bin/uuu.
Ok I will update it
Quoted 27 lines
Quoted 21 lines
board/bsh/bsh-imx8mn/readme.txt new file +14
-0+ + +Preparing the board +=================== + + * Connect a serial line to the board + * Power-up the board + + +Booting the board +================= + +By default the bootloader will search for the first valid image, starting +with the internal eMMC.configs/bsh_smms2pro_defconfig new file +0
-0configs/bsh_smms2pro_defconfig line 1
Quoted 1 line
configs/bsh_smms2pro_defconfig new file +1
-0@@ -0,0 +1,43 @@ +BR2_aarch64=yEven if the default happens to be correct, I prefer the subarch to be
specified explicitly. That way we can change the default later without affecting this defconfig.
Quoted 7 lines
configs/bsh_smms2pro_defconfig line 5
Quoted 4 lines
configs/bsh_smms2pro_defconfig new file +4
-0+BR2_TARGET_GENERIC_GETTY_PORT="ttymxc3" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/bsh/bsh-imx8mn/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="board/bsh/bsh-imx8mn/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="${UBOOT_DIR}/arch/arm/dts/imx8mn-bsh-smm-s2pro.dtb"I may be missing something, but this doesn't seem to be used by any of the
post- scripts?
Ok
Quoted 8 lines
configs/bsh_smms2pro_defconfig line 9
Quoted 5 lines
configs/bsh_smms2pro_defconfig new file +4
-0+BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git" +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="v5.17-rc1"Please use the tarball instead. Simply setting
CUSTOM_VERSIONshould be
sufficient - if not, linux.mk has tobe fixed.
Ok
Quoted 28 lines
Quoted 13 lines
configs/bsh_smms2pro_defconfig new file +12
-0+BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mn-bsh-smm-s2pro" +BR2_LINUX_KERNEL_DTB_KEEP_DIRNAME=y +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y +BR2_PACKAGE_FREESCALE_IMX=y +BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8MN=y +BR2_PACKAGE_FIRMWARE_IMX=y +BR2_PACKAGE_FIRMWARE_IMX_DDR3=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=yconfigs/bsh_smms2pro_defconfig line 31
Quoted 10 lines
configs/bsh_smms2pro_defconfig new file +10
-0+BR2_TARGET_ROOTFS_EXT2_SIZE="120M" +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.5" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mn" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="IMX_BOOT_UART_BASE=0x30a60000" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_GIT=y +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://gitlab.apertis.org/adalessandro/u-boot.git"Gitlab is able to generate tarballs as well. There are plenty of examples in
the tree.
Quoted 3 lines
I would normally fix these things up while applying, but since I'm not
entirely sure about merging a -rc kernel anyway, I'll wait for a v4 instead.
I will prepare v4
Michael
Quoted 18 lines
Oh, one more thing: the subject for a new defconfig is typically
"configs/bsh_smms2pro_defconfig: new defconfig"Regards,
ArnoutQuoted 12 lines
configs/bsh_smms2pro_defconfig new file +12
-0+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="v2022.01-bsh-smm2" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mn_bsh_smm_s2pro" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_PYTHON3=y +BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y +BR2_TARGET_UBOOT_NEEDS_OPENSSL=y +BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y +BR2_TARGET_UBOOT_NEEDS_IMX_FIRMWARE=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="flash.bin" +BR2_TARGET_UBOOT_SPL=y +BR2_PACKAGE_HOST_GENIMAGE=y
Signature · 15 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot
Quoted 7 lines · Michael Nazzareno Trimarchi
Hi
Quoted 4 lines · Arnout Vandecappelle
On 31/01/2022 15:55, Michael Trimarchi wrote:
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
I'm a bit uncomfortable to add an -rc version. But I guess it can be updated
as soon as 5.17 is released.Ok, I will then wait
No, what I meant to say is: it's OK to do it with the -rc, just make sure that
you update it to the release version when it comes around (which will still be another 8-ish weeks).
If we still manage to merge this board before 2022.02, we'll just backport the
bump to the LTS branch.
Regards,
Arnout
[snip]
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot
Quoted 19 lines · Arnout Vandecappelle
Quoted 16 lines · Michael Nazzareno Trimarchi
Hi
Quoted 11 lines · Arnout Vandecappelle
Quoted 3 lines · Michael Trimarchi
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
I'm a bit uncomfortable to add an -rc version. But I guess it can be updated
as soon as 5.17 is released.
Quoted 5 lines
Quoted 1 line
Ok, I will then wait
No, what I meant to say is: it's OK to do it with the -rc, just make sure that you update it to the release version when it comes around (which will still be another 8-ish weeks).
Support is now almost completely merged upstream for kernel and u-boot. We could update the patch to pull from:
* linux: v5.17 (audio for this board is enabled in v5.18-rc3)
* u-boot: v2022.07-rc1 (released on Mon 25 April 2022, 2 days remaining)
We can update later on the linux release to include to whole support and at least we can get rid of the custom u-boot repo/branch.
Regards,
Ariel
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot
Hi Ariel
Quoted 29 lines · Ariel D'Alessandro
Quoted 19 lines · Arnout Vandecappelle
Quoted 16 lines · Michael Nazzareno Trimarchi
Hi
Quoted 11 lines · Arnout Vandecappelle
Quoted 3 lines · Michael Trimarchi
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
I'm a bit uncomfortable to add an -rc version. But I guess it can
be updated
as soon as 5.17 is released.Quoted 5 lines
Quoted 1 line
Ok, I will then wait
No, what I meant to say is: it's OK to do it with the -rc, just make
sure that you update it to the release version when it comes around (which will still be another 8-ish weeks).
Quoted 9 lines
Support is now almost completely merged upstream for kernel and u-boot. We could update the patch to pull from:
* linux: v5.17 (audio for this board is enabled in v5.18-rc3)
* u-boot: v2022.07-rc1 (released on Mon 25 April 2022, 2 days remaining)We can update later on the linux release to include to whole support and at least we can get rid of the custom u-boot repo/branch.
Ok, sorry I was busy. I will resend them with your suggestion
Michael
Quoted 2 lines
Regards,
Ariel
Signature · 15 lines
Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 [email protected] __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 [email protected] www.amarulasolutions.com _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot
Hi,
Am Sa., 12. Feb. 2022 um 13:10 Uhr schrieb Arnout Vandecappelle <[email protected]>:
Quoted 92 lines · Michael Trimarchi
Quoted 3 lines
Add initial support for iMX8MN BSH SMM S2 PRO board:
- Linux: v5.17-rc1
I'm a bit uncomfortable to add an -rc version. But I guess it can be updated
as soon as 5.17 is released.Quoted 17 lines
- Uboot 2022-01-rc1 (reference tree)
- Default packages from buildroothttps://www.apertis.org/reference_hardware/imx8mn_bsh_smm_s2pro_setup/
Add Ariel D'Alessandro as co-maintainer, we work together on platform mainline
Build and tested using:
docker pull registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314Cc Ariel D'Alessandro <[email protected]>Cc Jagan Teki <[email protected]>Cc Heiko Thiery <[email protected]>Cc Giulio Benetti <[email protected]>Reviewed-by Giulio Benetti <[email protected]>Signed-off-by Michael Trimarchi <[email protected]>[snip]
DEVELOPERS F: configs/snps_archs38_hsdk_defconfig · line 223
Quoted 9 lines
DEVELOPERS +1
-0@@ -220,6 +220,7 @@ F: configs/snps_archs38_hsdk_defconfig F: configs/snps_archs38_vdk_defconfig N: Ariel D'Alessandro <[email protected]> +F: board/bsh/You should also add configs/bsh_smms2pro_defconfig here.
Quoted 51 lines
DEVELOPERS +1
-0F: package/axfsutils/ F: package/mali-t76x/@@ -2018,6 +2019,7 @@ F: package/python-crc16/ F: package/python-pyzmq/ N: Michael Trimarchi <[email protected]> +F: board/bsh/ F: package/python-spidev/ N: Michael Vetter <[email protected]>board/bsh/bsh-imx8mn/extlinux.conf new file +4
-0@@ -0,0 +1,4 @@ +label buildroot + kernel /boot/Image + devicetree /boot/freescale/imx8mn-bsh-smm-s2pro.dtb + append root=PARTUUID=%PARTUUID% rootwait rwboard/bsh/bsh-imx8mn/genimage.cfg new file +17
-0@@ -0,0 +1,17 @@ +image sdcard.img { + hdimage { + partition-table-type = "gpt" + } + + partition imx-boot { + in-partition-table = "no" + image = "flash.bin" + offset = 33K + } + + partition rootfs { + offset = 8M + image = "rootfs.ext4" + partition-uuid = %PARTUUID% + } +}board/bsh/bsh-imx8mn/post-build.sh new file +1
-0@@ -0,0 +1,7 @@ +#!/bin/sh
Quoted 8 lines
board/bsh/bsh-imx8mn/post-build.sh line 7
Quoted 6 lines
board/bsh/bsh-imx8mn/post-build.sh new file +6
-0+BOARD_DIR="$(dirname $0)" +PARTUUID="$($HOST_DIR/bin/uuidgen)" + +install -d "$TARGET_DIR/boot/extlinux/" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/extlinux.conf" > "$TARGET_DIR/boot/extlinux/extlinux.conf" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/genimage.cfg" > "$BINARIES_DIR/genimage.cfg"This is really a great way of doing it!
There was already a comment about that topic from Thomas:
https://lists.buildroot.org/pipermail/buildroot/2022-January/634308.html
Quoted 87 lines
Quoted 47 lines
board/bsh/bsh-imx8mn/post-image.sh new file +3
-0@@ -0,0 +1,3 @@ +#!/bin/sh + +support/scripts/genimage.sh -c ${BINARIES_DIR}/genimage.cfgboard/bsh/bsh-imx8mn/readme.txt new file +31
-0@@ -0,0 +1,55 @@ +How to build it +=============== + +Configure buildroot: + + $ make bsh_smms2pro_defconfig + +Change settings to fit your needs (optional): + + $ make menuconfig + +Compile everything and buildr the rootfs image: + + $ make + + +Result of the build +=================== + +After building, the output/images directory contains: + + output/images/ + ├── bl31.bin + ├── Image + ├── flash.bin + ├── ddr3* + ├── rootfs.ext2 + ├── rootfs.ext4 -> rootfs.ext2 + ├── rootfs.tar + ├── sdcard.img + ├── u-boot.binboard/bsh/bsh-imx8mn/readme.txt line 41
Quoted 10 lines
board/bsh/bsh-imx8mn/readme.txt new file +10
-0+ ├── u-boot-nodtb.bin + └── u-boot-spl.bin + + +Flashing the emmc card image +========================== + +To install the image on on eMMC + + $ sudo uuu -b emmc_all output/images/flash.bin output/images/sdcard.imgPlease also explain where you get uuu. Can we build it as part of buildroot?
Then refer to it as output/host/bin/uuu.Quoted 20 lines
board/bsh/bsh-imx8mn/readme.txt new file +14
-0+ + +Preparing the board +=================== + + * Connect a serial line to the board + * Power-up the board + + +Booting the board +================= + +By default the bootloader will search for the first valid image, starting +with the internal eMMC.configs/bsh_smms2pro_defconfig new file +0
-0configs/bsh_smms2pro_defconfig line 1
Quoted 1 line
configs/bsh_smms2pro_defconfig new file +1
-0@@ -0,0 +1,43 @@ +BR2_aarch64=yEven if the default happens to be correct, I prefer the subarch to be
specified explicitly. That way we can change the default later without affecting this defconfig.
Quoted 7 lines
configs/bsh_smms2pro_defconfig line 5
Quoted 4 lines
configs/bsh_smms2pro_defconfig new file +4
-0+BR2_TARGET_GENERIC_GETTY_PORT="ttymxc3" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/bsh/bsh-imx8mn/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="board/bsh/bsh-imx8mn/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="${UBOOT_DIR}/arch/arm/dts/imx8mn-bsh-smm-s2pro.dtb"I may be missing something, but this doesn't seem to be used by any of the
post- scripts?
This seems to be a leftover from the state where "board/freescale/common/imx/imx8-bootloader-prepare.sh" was used to generate the imx flash image. Now this is done by u-boot using binman Therefore this argument is no longer needed.
Quoted 57 lines
configs/bsh_smms2pro_defconfig line 9
Quoted 5 lines
configs/bsh_smms2pro_defconfig new file +4
-0+BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_GIT=y +BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git" +BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="v5.17-rc1"Please use the tarball instead. Simply setting
CUSTOM_VERSIONshould be
sufficient - if not, linux.mk has tobe fixed.Quoted 12 lines
configs/bsh_smms2pro_defconfig new file +12
-0+BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mn-bsh-smm-s2pro" +BR2_LINUX_KERNEL_DTB_KEEP_DIRNAME=y +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y +BR2_PACKAGE_FREESCALE_IMX=y +BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8MN=y +BR2_PACKAGE_FIRMWARE_IMX=y +BR2_PACKAGE_FIRMWARE_IMX_DDR3=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=yconfigs/bsh_smms2pro_defconfig line 31
Quoted 10 lines
configs/bsh_smms2pro_defconfig new file +10
-0+BR2_TARGET_ROOTFS_EXT2_SIZE="120M" +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.5" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mn" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="IMX_BOOT_UART_BASE=0x30a60000" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_GIT=y +BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://gitlab.apertis.org/adalessandro/u-boot.git"Gitlab is able to generate tarballs as well. There are plenty of examples in
the tree.I would normally fix these things up while applying, but since I'm not
entirely sure about merging a -rc kernel anyway, I'll wait for a v4 instead.Oh, one more thing: the subject for a new defconfig is typically
"configs/bsh_smms2pro_defconfig: new defconfig"Regards,
ArnoutQuoted 12 lines
configs/bsh_smms2pro_defconfig new file +12
-0+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="v2022.01-bsh-smm2" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mn_bsh_smm_s2pro" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_PYTHON3=y +BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y +BR2_TARGET_UBOOT_NEEDS_OPENSSL=y +BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y +BR2_TARGET_UBOOT_NEEDS_IMX_FIRMWARE=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="flash.bin" +BR2_TARGET_UBOOT_SPL=y +BR2_PACKAGE_HOST_GENIMAGE=y
Signature · 5 lines
Heiko _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot