ARM: digicolor: misc updates for 4.3
Subsystems (2)
cover ARM: digicolor: misc updates for 4.3
This series contains the following updates for Conexant Digicolor machines:
* Enable the watchdog driver that was added during the 4.2 merge window, both in .dtsi and in multi_v7_defconfig
* Use the standard stdout-path property in the chosen node to configure the console
* Make .dts/.dtsi files to the Digicolor MAINTAINERS entry
Based on v4.2-rc1.
Baruch Siach (4):
ARM: digicolor: enable watchdog device
ARM: multi_v7_defconfig: enable Conexant Digicolor watchdog
ARM: digicolor: dts: use stdout-path for console configuration
MAINTAINERS: digicolor: add dts files
MAINTAINERS | 1 + arch/arm/boot/dts/cx92755.dtsi | 7 +++++++ arch/arm/boot/dts/cx92755_equinox.dts | 3 +-- arch/arm/configs/multi_v7_defconfig | 1 + 4 files changed, 10 insertions(+), 2 deletions(-)
Signature · 1 line
2.1.4
PATCH 1/4 ARM: digicolor: enable watchdog device
--- arch/arm/boot/dts/cx92755.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/boot/dts/cx92755.dtsi +7 -0
@@ -88,6 +88,13 @@ interrupts = <25>; }; + watchdog at f0000fc0 { + compatible = "cnxt,cx92755-wdt"; + reg = <0xf0000fc0 0x8>; + clocks = <&main_clk>; + timeout-sec = <15>; + }; + uc_regs: syscon at f00003a0 { compatible = "cnxt,cx92755-uc", "syscon"; reg = <0xf00003a0 0x10>;
Signature · 1 line
2.1.4
PATCH 2/4 ARM: multi_v7_defconfig: enable Conexant Digicolor watchdog
In reply to Baruch Siach--- arch/arm/configs/multi_v7_defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/configs/multi_v7_defconfig +1 -0
@@ -372,6 +372,7 @@ CONFIG_ORION_WATCHDOG=y CONFIG_ST_LPC_WATCHDOG=y CONFIG_SUNXI_WATCHDOG=y CONFIG_MESON_WATCHDOG=y +CONFIG_DIGICOLOR_WATCHDOG=y CONFIG_MFD_AS3711=y CONFIG_MFD_AS3722=y CONFIG_MFD_BCM590XX=y
Signature · 1 line
2.1.4
PATCH 3/4 ARM: digicolor: dts: use stdout-path for console configuration
In reply to Baruch Siach--- arch/arm/boot/dts/cx92755_equinox.dts | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
arch/arm/boot/dts/cx92755_equinox.dts +1 -2
@@ -64,8 +64,7 @@ }; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; };
Signature · 1 line
2.1.4
PATCH 4/4 MAINTAINERS: digicolor: add dts files
In reply to Baruch SiachThe 'digicolor' regexp doesn't cover the dts files. Add a glob pattern for them.
--- MAINTAINERS | 1 + 1 file changed, 1 insertion(+)
MAINTAINERS +1 -0
@@ -1001,6 +1001,7 @@ ARM/CONEXANT DIGICOLOR MACHINE SUPPORT M: Baruch Siach <[email protected]> L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers) S: Maintained +F: arch/arm/boot/dts/cx92755* N: digicolor ARM/EBSA110 MACHINE SUPPORT
Signature · 1 line
2.1.4
Olof Johansson
AppliedPATCH 4/4 MAINTAINERS: digicolor: add dts files
Quoted 4 lines · Baruch Siach
The 'digicolor' regexp doesn't cover the dts files. Add a glob pattern for them.
Signed-off-by Baruch Siach <[email protected]>
Thanks, applied to fixes.
-Olof
cover ARM: digicolor: misc updates for 4.3
In reply to Baruch SiachQuoted 10 lines · Baruch Siach
This series contains the following updates for Conexant Digicolor machines:
* Enable the watchdog driver that was added during the 4.2 merge window, both in .dtsi and in
multi_v7_defconfig* Use the standard stdout-path property in the chosen node to configure the console
* Make .dts/.dtsi files to the Digicolor
MAINTAINERSentry
Quoted 7 lines
Based on v4.2-rc1.
Baruch Siach (4):
ARM: digicolor: enable watchdog device
ARM:multi_v7_defconfig: enable Conexant Digicolor watchdog
ARM: digicolor: dts: use stdout-path for console configuration
MAINTAINERS: digicolor: add dts files
Thanks, I applied the two DT patches to next/dt, the defconfig change to next/defconfig.
-Olof