Skip to contentSkip to conversation

Update the QEMU PLIC addresses

PATCH New Alistair Francis 1 participant 3 messages Apr 4, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v3 cover Update the QEMU PLIC addresses

This series updates the PLIC address to match the documentation. This fixes: https://github.com/riscv/opensbi/issues/97
V3:
- Fix SiFive U crash
V2:
- Squash patches to ensure biesctability

Alistair Francis (2):
riscv: plic: Fix incorrect irq calculation
riscv: plic: Log guest errors

 hw/riscv/sifive_plic.c      | 16 +++++++++++-----
 include/hw/riscv/sifive_e.h |  2 +-
 include/hw/riscv/sifive_u.h |  4 ++--
 include/hw/riscv/virt.h     |  2 +-
 4 files changed, 15 insertions(+), 9 deletions(-)
Signature · 1 line
2.21.0
#1 lore raw

PATCH v3 1/2 riscv: plic: Fix incorrect irq calculation

This patch fixes four different things, to maintain bisectability they have been merged into a single patch. The following fixes are below:

sifive_plic: Fix incorrect irq calculation
The irq is incorrectly calculated to be off by one. It has worked in the past as the priority_base offset has also been set incorrectly. We are about to fix the priority_base offset so first first the irq calculation.

sifive_u: Fix PLIC priority base offset and numbering According to the FU540 manual the PLIC source priority address starts at an offset of 0x04 and not 0x00. The same manual also specifies that the PLIC only has 53 source priorities. Fix these two incorrect header files.

We also need to over extend the plic_gpios[] array as the PLIC sources count from 1 and not 0.

riscv: sifive_e: Fix PLIC priority base offset
According to the FE31 manual the PLIC source priority address starts at an offset of 0x04 and not 0x00.

riscv: virt: Fix PLIC priority base offset
Update the virt offsets based on the newly updated SiFive U and SiFive E offsets.

---
 hw/riscv/sifive_plic.c      | 4 ++--
 include/hw/riscv/sifive_e.h | 2 +-
 include/hw/riscv/sifive_u.h | 4 ++--
 include/hw/riscv/virt.h     | 2 +-
 4 files changed, 6 insertions(+), 6 deletions(-)
hw/riscv/sifive_plic.c +2 -2
index ac768e6c27..0315e035e5 100644
@@ -207,7 +207,7 @@ static uint64_t sifive_plic_read(void *opaque, hwaddr addr, unsigned size)
     if (addr >= plic->priority_base && /* 4 bytes per source */
         addr < plic->priority_base + (plic->num_sources << 2))
     {
-        uint32_t irq = (addr - plic->priority_base) >> 2;
+        uint32_t irq = ((addr - plic->priority_base) >> 2) + 1;
         if (RISCV_DEBUG_PLIC) {
             qemu_log("plic: read priority: irq=%d priority=%d\n",
                 irq, plic->source_priority[irq]);
@@ -280,7 +280,7 @@ static void sifive_plic_write(void *opaque, hwaddr addr, uint64_t value,
     if (addr >= plic->priority_base && /* 4 bytes per source */
         addr < plic->priority_base + (plic->num_sources << 2))
     {
-        uint32_t irq = (addr - plic->priority_base) >> 2;
+        uint32_t irq = ((addr - plic->priority_base) >> 2) + 1;
         plic->source_priority[irq] = value & 7;
         if (RISCV_DEBUG_PLIC) {
             qemu_log("plic: write priority: irq=%d priority=%d\n",
include/hw/riscv/sifive_e.h +1 -1
index 7b6d8aed96..f715f8606f 100644
@@ -70,7 +70,7 @@ enum {
 #define SIFIVE_E_PLIC_HART_CONFIG "M"
 #define SIFIVE_E_PLIC_NUM_SOURCES 127
 #define SIFIVE_E_PLIC_NUM_PRIORITIES 7
-#define SIFIVE_E_PLIC_PRIORITY_BASE 0x0
+#define SIFIVE_E_PLIC_PRIORITY_BASE 0x04
 #define SIFIVE_E_PLIC_PENDING_BASE 0x1000
 #define SIFIVE_E_PLIC_ENABLE_BASE 0x2000
 #define SIFIVE_E_PLIC_ENABLE_STRIDE 0x80
include/hw/riscv/sifive_u.h +2 -2
index be13cc1304..892f0eee21 100644
@@ -68,9 +68,9 @@ enum {
 };
 
 #define SIFIVE_U_PLIC_HART_CONFIG "MS"
-#define SIFIVE_U_PLIC_NUM_SOURCES 127
+#define SIFIVE_U_PLIC_NUM_SOURCES 54
 #define SIFIVE_U_PLIC_NUM_PRIORITIES 7
-#define SIFIVE_U_PLIC_PRIORITY_BASE 0x0
+#define SIFIVE_U_PLIC_PRIORITY_BASE 0x04
 #define SIFIVE_U_PLIC_PENDING_BASE 0x1000
 #define SIFIVE_U_PLIC_ENABLE_BASE 0x2000
 #define SIFIVE_U_PLIC_ENABLE_STRIDE 0x80
include/hw/riscv/virt.h +1 -1
index f12deaebd6..568764b570 100644
@@ -59,7 +59,7 @@ enum {
 #define VIRT_PLIC_HART_CONFIG "MS"
 #define VIRT_PLIC_NUM_SOURCES 127
 #define VIRT_PLIC_NUM_PRIORITIES 7
-#define VIRT_PLIC_PRIORITY_BASE 0x0
+#define VIRT_PLIC_PRIORITY_BASE 0x04
 #define VIRT_PLIC_PENDING_BASE 0x1000
 #define VIRT_PLIC_ENABLE_BASE 0x2000
 #define VIRT_PLIC_ENABLE_STRIDE 0x80
Signature · 1 line
2.21.0
#2 lore raw

PATCH v3 2/2 riscv: plic: Log guest errors

In reply to Alistair Francis

Instead of using error_report() to print guest errors let's use qemu_log_mask(LOG_GUEST_ERROR,...) to log the error.

---
 hw/riscv/sifive_plic.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)
hw/riscv/sifive_plic.c +9 -3
index 0315e035e5..07a032d93d 100644
@@ -263,7 +263,9 @@ static uint64_t sifive_plic_read(void *opaque, hwaddr addr, unsigned size)
     }
 
 err:
-    error_report("plic: invalid register read: %08x", (uint32_t)addr);
+    qemu_log_mask(LOG_GUEST_ERROR,
+                  "%s: Invalid register read 0x%" HWADDR_PRIx "\n",
+                  __func__, addr);
     return 0;
 }
 
@@ -290,7 +292,9 @@ static void sifive_plic_write(void *opaque, hwaddr addr, uint64_t value,
     } else if (addr >= plic->pending_base && /* 1 bit per source */
                addr < plic->pending_base + (plic->num_sources >> 3))
     {
-        error_report("plic: invalid pending write: %08x", (uint32_t)addr);
+        qemu_log_mask(LOG_GUEST_ERROR,
+                      "%s: invalid pending write: 0x%" HWADDR_PRIx "",
+                      __func__, addr);
         return;
     } else if (addr >= plic->enable_base && /* 1 bit per source */
         addr < plic->enable_base + plic->num_addrs * plic->enable_stride)
@@ -340,7 +344,9 @@ static void sifive_plic_write(void *opaque, hwaddr addr, uint64_t value,
     }
 
 err:
-    error_report("plic: invalid register write: %08x", (uint32_t)addr);
+    qemu_log_mask(LOG_GUEST_ERROR,
+                  "%s: Invalid register write 0x%" HWADDR_PRIx "\n",
+                  __func__, addr);
 }
 
 static const MemoryRegionOps sifive_plic_ops = {
Signature · 1 line
2.21.0