Support pli1209bc Digital Supervisor

Add vendor prefix for Vicor Corporation.

Signed-off-by Marcello Sylvester Bauer <[email protected]>

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

Add vendor prefix for Vicor Corporation.

Signed-off-by Marcello Sylvester Bauer <[email protected]>

Acked-by Rob Herring <[email protected]>

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0

index 294093d45a23..047a83a089ce 100644
@@ -1298,6 +1298,8 @@ patternProperties:
     description: Vertexcom Technologies, Inc.
   "^via,.*":
     description: VIA Technologies, Inc.
+  "^vicor,.*":
+    description: Vicor Corporation
   "^videostrong,.*":
     description: Videostrong Technology Co., Ltd.
   "^virtio,.*":

Add trivial device entry for PLI1209BC Digital Supervisor from Vicor Corporation.

Signed-off-by Marcello Sylvester Bauer <[email protected]>

---
 Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
 1 file changed, 2 insertions(+)

Add trivial device entry for PLI1209BC Digital Supervisor from Vicor Corporation.

Signed-off-by Marcello Sylvester Bauer <[email protected]>

Acked-by Rob Herring <[email protected]>

---
 Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
 1 file changed, 2 insertions(+)

Documentation/devicetree/bindings/trivial-devices.yaml +2 -0

index 091792ba993e..d03d90360aa0 100644
@@ -354,6 +354,8 @@ properties:
           - ti,tps544c25
             # Winbond/Nuvoton H/W Monitor
           - winbond,w83793
+            # Vicor Corporation Digital Supervisor
+          - vicor,pli1209bc
             # i2c trusted platform module (TPM)
           - winbond,wpct301
 

PLI1209BC is a Digital Supervisor from Vicor Corporation.

Signed-off-by Marcello Sylvester Bauer <[email protected]>

---
 Documentation/hwmon/index.rst     |   1 +
 Documentation/hwmon/pli1209bc.rst |  75 +++++++++++++++++++
 drivers/hwmon/pmbus/Kconfig       |   9 +++
 drivers/hwmon/pmbus/Makefile      |   1 +
 drivers/hwmon/pmbus/pli1209bc.c   | 115 ++++++++++++++++++++++++++++++
 5 files changed, 201 insertions(+)
 create mode 100644 Documentation/hwmon/pli1209bc.rst
 create mode 100644 drivers/hwmon/pmbus/pli1209bc.c

Documentation/hwmon/index.rst +1 -0

index b69fdaf1af82..075d1defcd20 100644
@@ -161,6 +161,7 @@ Hardware Monitoring Kernel Drivers
    pc87427
    pcf8591
    pim4328
+   pli1209bc
    pm6764tr
    pmbus
    powr1220

Documentation/hwmon/pli1209bc.rst new file +75 -0

new file mode 100644
index 000000000000..ea5b3f68a515
@@ -0,0 +1,75 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver pli1209bc
+=======================
+
+Supported chips:
+
+  * Digital Supervisor PLI1209BC
+
+    Prefix: 'pli1209bc'
+
+    Addresses scanned: 0x50 - 0x5F
+
+    Datasheet: https://www.vicorpower.com/documents/datasheets/ds-PLI1209BCxyzz-VICOR.pdf
+
+Authors:
+    - Marcello Sylvester Bauer <[email protected]>
+
+Description
+-----------
+
+The Vicor PLI1209BC is an isolated digital power system supervisor that provides
+a communication interface between a host processor and one Bus Converter Module
+(BCM). The PLI communicates with a system controller via a PMBus compatible
+interface over an isolated UART interface. Through the PLI, the host processor
+can configure, set protection limits, and monitor the BCM.
+
+Sysfs entries
+-------------
+
+======================= ========================================================
+in1_label		"vin2"
+in1_input		Input voltage.
+in1_rated_min		Minimum rated input voltage.
+in1_rated_max		Maximum rated input voltage.
+in1_max			Maximum input voltage.
+in1_max_alarm		Input voltage high alarm.
+in1_crit		Critical input voltage.
+in1_crit_alarm		Input voltage critical alarm.
+
+in2_label		"vout2"
+in2_input		Output voltage.
+in2_rated_min		Minimum rated output voltage.
+in2_rated_max		Maximum rated output voltage.
+in2_alarm		Output voltage alarm
+
+curr1_label		"iin2"
+curr1_input		Input current.
+curr1_max		Maximum input current.
+curr1_max_alarm		Maximum input current high alarm.
+curr1_crit		Critical input current.
+curr1_crit_alarm	Input current critical alarm.
+
+curr2_label		"iout2"
+curr2_input		Output current.
+curr2_crit		Critical output current.
+curr2_crit_alarm	Output current critical alarm.
+curr2_max		Maximum output current.
+curr2_max_alarm		Output current high alarm.
+
+power1_label		"pin2"
+power1_input		Input power.
+power1_alarm		Input power alarm.
+
+power2_label		"pout2"
+power2_input		Output power.
+power2_rated_max	Maximum rated output power.
+
+temp1_input		Die temperature.
+temp1_alarm		Die temperature alarm.
+temp1_max		Maximum die temperature.
+temp1_max_alarm		Die temperature high alarm.
+temp1_crit		Critical die temperature.
+temp1_crit_alarm	Die temperature critical alarm.
+======================= ========================================================

drivers/hwmon/pmbus/Kconfig +9 -0

index c73aa50c7615..f18f67a94697 100644
@@ -317,6 +317,15 @@ config SENSORS_PIM4328
 	  This driver can also be built as a module. If so, the module will
 	  be called pim4328.
 
+config SENSORS_PLI1209BC
+	tristate "Vicor PLI1209BC"
+	help
+	  If you say yes here you get hardware monitoring support for Vicor
+	  PLI1209BC Digital Supervisor.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called pli1209bc.
+
 config SENSORS_PM6764TR
 	tristate "ST PM6764TR"
 	help

drivers/hwmon/pmbus/Makefile +1 -0

index e5935f70c9e0..a4a96ac71de7 100644
@@ -33,6 +33,7 @@ obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
 obj-$(CONFIG_SENSORS_MP2888)	+= mp2888.o
 obj-$(CONFIG_SENSORS_MP2975)	+= mp2975.o
 obj-$(CONFIG_SENSORS_MP5023)	+= mp5023.o
+obj-$(CONFIG_SENSORS_PLI1209BC)	+= pli1209bc.o
 obj-$(CONFIG_SENSORS_PM6764TR)	+= pm6764tr.o
 obj-$(CONFIG_SENSORS_PXE1610)	+= pxe1610.o
 obj-$(CONFIG_SENSORS_Q54SJ108A2)	+= q54sj108a2.o

drivers/hwmon/pmbus/pli1209bc.c new file +115 -0

new file mode 100644
index 000000000000..5f8847307e55
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Hardware monitoring driver for Vicor PLI1209BC Digital Supervisor
+ *
+ * Copyright (c) 2022 9elements GmbH
+ */
+
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pmbus.h>
+#include "pmbus.h"
+
+/*
+ * The capability command is only supported at page 0. Probing the device while
+ * the page register is set to 1 will falsely enable PEC support. Disable
+ * capability probing accordingly, since the PLI1209BC does not have any
+ * additional capabilities.
+ */
+static struct pmbus_platform_data pli1209bc_plat_data = {
+	.flags = PMBUS_NO_CAPABILITY,
+};
+
+static int pli1209bc_read_word_data(struct i2c_client *client, int page,
+				    int phase, int reg)
+{
+	int data;
+
+	switch (reg) {
+	/* PMBUS_READ_POUT uses a direct format with R=0 */
+	case PMBUS_READ_POUT:
+		data = pmbus_read_word_data(client, page, phase, reg);
+		if (data < 0)
+			return data;
+		data = sign_extend32(data, 15) * 10;
+		return clamp_val(data, -32768, 32767) & 0xffff;
+	default:
+		return -ENODATA;
+	}
+}
+
+static struct pmbus_driver_info pli1209bc_info = {
+	.pages = 2,
+	.format[PSC_VOLTAGE_IN] = direct,
+	.format[PSC_VOLTAGE_OUT] = direct,
+	.format[PSC_CURRENT_IN] = direct,
+	.format[PSC_CURRENT_OUT] = direct,
+	.format[PSC_POWER] = direct,
+	.format[PSC_TEMPERATURE] = direct,
+	.m[PSC_VOLTAGE_IN] = 1,
+	.b[PSC_VOLTAGE_IN] = 0,
+	.R[PSC_VOLTAGE_IN] = 1,
+	.m[PSC_VOLTAGE_OUT] = 1,
+	.b[PSC_VOLTAGE_OUT] = 0,
+	.R[PSC_VOLTAGE_OUT] = 1,
+	.m[PSC_CURRENT_IN] = 1,
+	.b[PSC_CURRENT_IN] = 0,
+	.R[PSC_CURRENT_IN] = 3,
+	.m[PSC_CURRENT_OUT] = 1,
+	.b[PSC_CURRENT_OUT] = 0,
+	.R[PSC_CURRENT_OUT] = 2,
+	.m[PSC_POWER] = 1,
+	.b[PSC_POWER] = 0,
+	.R[PSC_POWER] = 1,
+	.m[PSC_TEMPERATURE] = 1,
+	.b[PSC_TEMPERATURE] = 0,
+	.R[PSC_TEMPERATURE] = 0,
+	/*
+	 * Page 0 sums up all attributes except voltage readings.
+	 * The pli1209 digital supervisor only contains a single BCM, making
+	 * page 0 redundant.
+	 */
+	.func[1] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT
+	    | PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT
+	    | PMBUS_HAVE_PIN | PMBUS_HAVE_POUT
+	    | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
+	    | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_INPUT,
+	.read_word_data = pli1209bc_read_word_data,
+};
+
+static int pli1209bc_probe(struct i2c_client *client)
+{
+	client->dev.platform_data = &pli1209bc_plat_data;
+	return pmbus_do_probe(client, &pli1209bc_info);
+}
+
+static const struct i2c_device_id pli1209bc_id[] = {
+	{"pli1209bc", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, pli1209bc_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id pli1209bc_of_match[] = {
+	{ .compatible = "vicor,pli1209bc" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, pli1209bc_of_match);
+#endif
+
+static struct i2c_driver pli1209bc_driver = {
+	.driver = {
+		   .name = "pli1209bc",
+		   .of_match_table = of_match_ptr(pli1209bc_of_match),
+		   },
+	.probe_new = pli1209bc_probe,
+	.id_table = pli1209bc_id,
+};
+
+module_i2c_driver(pli1209bc_driver);
+
+MODULE_AUTHOR("Marcello Sylvester Bauer <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for Vicor PLI1209BC");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(PMBUS);

Add regulator support for PLI1209BC Digital Supervisor.

Signed-off-by Marcello Sylvester Bauer <[email protected]>

---
 drivers/hwmon/pmbus/Kconfig     |  7 +++++++
 drivers/hwmon/pmbus/pli1209bc.c | 31 +++++++++++++++++++++++++++++++
 2 files changed, 38 insertions(+)

drivers/hwmon/pmbus/Kconfig +7 -0

index f18f67a94697..6552467c588d 100644
@@ -326,6 +326,13 @@ config SENSORS_PLI1209BC
 	  This driver can also be built as a module. If so, the module will
 	  be called pli1209bc.
 
+config SENSORS_PLI1209BC_REGULATOR
+	bool "Regulator support for PLI1209BC"
+	depends on SENSORS_PLI1209BC && REGULATOR
+	help
+	  If you say yes here you get regulator support for Vicor PLI1209BC
+	  Digital Supervisor.
+
 config SENSORS_PM6764TR
 	tristate "ST PM6764TR"
 	help

drivers/hwmon/pmbus/pli1209bc.c +31 -0

index 5f8847307e55..05b4ee35ba27 100644
@@ -8,6 +8,7 @@
 #include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/pmbus.h>
+#include <linux/regulator/driver.h>
 #include "pmbus.h"
 
 /*

@@ -33,11 +34,37 @@ static int pli1209bc_read_word_data(struct i2c_client *client, int page,
 			return data;
 		data = sign_extend32(data, 15) * 10;
 		return clamp_val(data, -32768, 32767) & 0xffff;
+	/*
+	 * PMBUS_READ_VOUT and PMBUS_READ_TEMPERATURE_1 return invalid data
+	 * when the BCM is turned off. Since it is not possible to return
+	 * ENODATA error, return zero instead.
+	 */
+	case PMBUS_READ_VOUT:
+	case PMBUS_READ_TEMPERATURE_1:
+		data = pmbus_read_word_data(client, page, phase,
+					    PMBUS_STATUS_WORD);
+		if (data < 0)
+			return data;
+		if (data & PB_STATUS_POWER_GOOD_N)
+			return 0;
+		return pmbus_read_word_data(client, page, phase, reg);
 	default:
 		return -ENODATA;
 	}
 }
 
+#if IS_ENABLED(CONFIG_SENSORS_PLI1209BC_REGULATOR)
+static const struct regulator_desc pli1209bc_reg_desc = {
+	.name = "vout2",
+	.id = 1,
+	.of_match = of_match_ptr("vout2"),
+	.regulators_node = of_match_ptr("regulators"),
+	.ops = &pmbus_regulator_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+};
+#endif
+
 static struct pmbus_driver_info pli1209bc_info = {
 	.pages = 2,
 	.format[PSC_VOLTAGE_IN] = direct,

@@ -75,6 +102,10 @@ static struct pmbus_driver_info pli1209bc_info = {
 	    | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
 	    | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_INPUT,
 	.read_word_data = pli1209bc_read_word_data,
+#if IS_ENABLED(CONFIG_SENSORS_PLI1209BC_REGULATOR)
+	.num_regulators = 1,
+	.reg_desc = &pli1209bc_reg_desc,
+#endif
 };
 
 static int pli1209bc_probe(struct i2c_client *client)