Skip to contentSkip to conversation

Porting custom board from u-boot 1.0.1 to u-boot 1.1.2

U-Boot-Users Armand Ciejak 3 participants 5 messages Mar 14, 2005 – Mar 21, 2005

lore
Share & tools
lore
#0 lore raw

I'm working on the Metrowerks "QUICCstart 8540 Evaluation System" which is provided with u-boot 1.0.1 (custom board configuration called EVAL8540). I have got the source code from the installation CD and want to port it to the latest u-boot version.
To do that I would like to know the changes which occured between this two version of the u-boot project and what do I have to adapt in the source code of the EVAL8540 configuration.

PS: I already installed the ELDK 3.1 on my Linux PC.

Best regards and thanks in advance,

Armand

#1 lore raw

[U-Boot-Users] smc91111 and MII

Evening (o;

Is this a generic behaviour among all ethernet drivers that it get's reset every time before it is used like the smc91111?

So we just block ourself out to use the MII commands although functions are in the driver ready to be used (with some slight modifications ;o).

best regards
rick

#2 lore raw
In reply to Armand Ciejak
Quoted 1 line · In message <[email protected]> you wrote:

I'm working on the Metrowerks "QUICCstart 8540 Evaluation System" which

Please bear with my ignorance, but is this different from the MPC8540ADS board?

Quoted 2 lines

To do that I would like to know the changes which occured between this two version of the u-boot project and what do I have to adapt in the

Identify which specific version the port was based on, and then use "cvs diff". You may also want to run "cvsps" to break the changes down into patchsets. See also the CHANGELOG file for documentation about changes.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
People are always a lot more complicated than you  think.  It's  very
important to remember that.             - Terry Pratchett, _Truckers_
#3 lore raw
Quoted 5 lines · Wolfgang Denk
Quoted 1 line · In message <[email protected]> you wrote:

I'm working on the Metrowerks "QUICCstart 8540 Evaluation System" which

Please bear with my ignorance, but is this different from the MPC8540ADS board?

The main difference I noticed in the hardware parts are:

MPC8540ADS Metrowerks boards
Flash

32bit                     16bit
16MB                      8MB
?                         Intel 28F640J3

SDRAM
64 MB no SDRAM

DDR
128 MB 256 MB

Quoted 13 lines
Quoted 3 lines

To do that I would like to know the changes which occured between this two version of the u-boot project and what do I have to adapt in the

Identify which specific version the port was based on, and then use "cvs diff". You may also want to run "cvsps" to break the changes down into patchsets. See also the CHANGELOG file for documentation about changes.

Best regards,

Wolfgang Denk

#4 lore raw
Quoted 5 lines · In message <[email protected]> you wrote:
Quoted 3 lines

Please bear with my ignorance, but is this different from the MPC8540ADS board?

The main difference I noticed in the hardware parts are:

I see. Consider it a new port, then.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
For every complex problem, there is a solution that is simple,  neat,
and wrong.                                           -- H. L. Mencken