spl, Makefile: Take external offset into account for fit images
PATCH 1/1 spl, Makefile: Take external offset into account for fit images
When building a FIT image for SPL to load also take into account the configured external offset. This allows the SPL to load the u-boot FIT image correctly when configuring SECURE_BOOT on i.mx6 is enabled (with CONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Note this doesn't allow secure booting; but it does allow an unsigned SPL/u-boot with secure boot support eanbled to boot on open device.
---
Makefile | 1 + 1 file changed, 1 insertion(+)
Makefile +1 -0
@@ -1240,6 +1240,7 @@ endif ifdef CONFIG_SPL_LOAD_FIT MKIMAGEFLAGS_u-boot.img = -f auto -A $(ARCH) -T firmware -C none -O u-boot \ -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_UBOOT_START) \ + -p $(CONFIG_FIT_EXTERNAL_OFFSET) \ -n "U-Boot $(UBOOTRELEASE) for $(BOARD) board" -E \ $(patsubst %,-b arch/$(ARCH)/dts/%.dtb,$(subst ",,$(CONFIG_OF_LIST))) else
Signature · 1 line
2.20.1
PATCH 1/1 spl, Makefile: Take external offset into account for fit images
Quoted 7 lines · Sjoerd Simons
When building a FIT image for SPL to load also take into account the configured external offset. This allows the SPL to load the u-boot FIT image correctly when configuring
SECURE_BOOTon i.mx6 is enabled (withCONFIG_FIT_EXTERNAL_OFFSET=0x3000).Note this doesn't allow secure booting; but it does allow an unsigned SPL/u-boot with secure boot support eanbled to boot on open device.
Does this change behavior on systems which don't use CONFIG_FIT_EXTERNAL_OFFSET ?
Quoted 20 lines
Signed-off-by Sjoerd Simons <[email protected]>---
Makefile | 1 + 1 file changed, 1 insertion(+)Makefile +1
-0@@ -1240,6 +1240,7 @@ endif ifdef CONFIG_SPL_LOAD_FIT MKIMAGEFLAGS_u-boot.img = -f auto -A $(ARCH) -T firmware -C none -O u-boot \ -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_UBOOT_START) \ + -p $(CONFIG_FIT_EXTERNAL_OFFSET) \ -n "U-Boot $(UBOOTRELEASE) for $(BOARD) board" -E \ $(patsubst %,-b arch/$(ARCH)/dts/%.dtb,$(subst ",,$(CONFIG_OF_LIST))) else
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/1 spl, Makefile: Take external offset into account for fit images
Quoted 8 lines · Marek Vasut
Quoted 7 lines · Sjoerd Simons
When building a FIT image for SPL to load also take into account the
configured external offset. This allows the SPL to load the u-boot FIT
image correctly when configuringSECURE_BOOTon i.mx6 is enabled (withCONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Quoted 6 lines
Quoted 3 lines
Note this doesn't allow secure booting; but it does allow an unsigned
SPL/u-boot with secure boot support eanbled to boot on open device.Does this change behavior on systems which don't use
CONFIG_FIT_EXTERNAL_OFFSET?
Nope; in that case the default CONFIG_FIT_EXTERNAL_OFFSET is 0x0, which gets essentially ignored if passed as a argument to -p
Quoted 25 lines
Quoted 23 lines
Signed-off-by Sjoerd Simons <[email protected]>---
Makefile | 1 + 1 file changed, 1 insertion(+)Makefile +1
-1@@ -1240,6 +1240,7 @@ endif ifdef CONFIG_SPL_LOAD_FIT MKIMAGEFLAGS_u-boot.img = -f auto -A $(ARCH) -T firmware -C none -O u-boot \ -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_UBOOT_START) \ + -p $(CONFIG_FIT_EXTERNAL_OFFSET) \ -n "U-Boot $(UBOOTRELEASE) for $(BOARD) board" -E \ $(patsubst %,-b arch/$(ARCH)/dts/%.dtb,$(subst",,$(CONFIG_OF_LIST)))
else
Signature · 2 lines
Sjoerd Simons Collabora Ltd.