Skip to contentSkip to conversation

net: dsa: lantiq_gswip: add registers specific for MaxLinear GSW1xx

RFC PATCH In review Daniel Golle 2 participants 3 messages Aug 16, 2025 – Aug 21, 2025

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

RFC PATCH 20/23 net: dsa: lantiq_gswip: add registers specific for MaxLinear GSW1xx

Add registers needed for MaxLinear GSW1xx family of dedicated switch ICs connected via MDIO or SPI.

---
 drivers/net/dsa/lantiq_gswip.h | 109 +++++++++++++++++++++++++++++++++
 1 file changed, 109 insertions(+)
drivers/net/dsa/lantiq_gswip.h +109 -0
index fd898991180d..e8914480d59e 100644
@@ -224,6 +224,114 @@
 
 #define XRX200_GPHY_FW_ALIGN	(16 * 1024)
 
+#define GSW1XX_PORTS				6
+/* Port used for RGMII or optional RMII */
+#define GSW1XX_MII_PORT				0x5
+/* Port used for SGMII */
+#define GSW1XX_SGMII_PORT			0x4
+
+#define GSW1XX_SYS_CLK_FREQ			340000000
+
+/* SMDIO switch register base address */
+#define GSW1XX_SMDIO_BADR			0x1f
+#define  GSW1XX_SMDIO_BADR_UNKNOWN		-1
+
+/* GSW1XX SGMII PCS */
+#define GSW1XX_SGMII_BASE			0xd000
+#define GSW1XX_SGMII_PHY_HWBU_CTRL		0x009
+#define  GSW1XX_SGMII_PHY_HWBU_CTRL_EN_HWBU_FSM	BIT(0)
+#define  GSW1XX_SGMII_PHY_HWBU_CTRL_HW_FSM_EN	BIT(3)
+#define GSW1XX_SGMII_TBI_TXANEGH		0x300
+#define GSW1XX_SGMII_TBI_TXANEGL		0x301
+#define GSW1XX_SGMII_TBI_ANEGCTL		0x304
+#define  GSW1XX_SGMII_TBI_ANEGCTL_LT		GENMASK(1, 0)
+#define   GSW1XX_SGMII_TBI_ANEGCTL_LT_10US	0
+#define   GSW1XX_SGMII_TBI_ANEGCTL_LT_1_6MS	1
+#define   GSW1XX_SGMII_TBI_ANEGCTL_LT_5MS	2
+#define   GSW1XX_SGMII_TBI_ANEGCTL_LT_10MS	3
+#define  GSW1XX_SGMII_TBI_ANEGCTL_ANEGEN	BIT(2)
+#define  GSW1XX_SGMII_TBI_ANEGCTL_RANEG		BIT(3)
+#define  GSW1XX_SGMII_TBI_ANEGCTL_OVRABL	BIT(4)
+#define  GSW1XX_SGMII_TBI_ANEGCTL_OVRANEG	BIT(5)
+#define  GSW1XX_SGMII_TBI_ANEGCTL_ANMODE	GENMASK(7, 6)
+#define   GSW1XX_SGMII_TBI_ANEGCTL_ANMODE_1000BASEX	1
+#define   GSW1XX_SGMII_TBI_ANEGCTL_ANMODE_SGMII_PHY	2
+#define   GSW1XX_SGMII_TBI_ANEGCTL_ANMODE_SGMII_MAC	3
+#define  GSW1XX_SGMII_TBI_ANEGCTL_BCOMP		BIT(15)
+
+#define GSW1XX_SGMII_TBI_TBICTL			0x305
+#define  GSW1XX_SGMII_TBI_TBICTL_INITTBI	BIT(0)
+#define  GSW1XX_SGMII_TBI_TBICTL_ENTBI		BIT(1)
+#define  GSW1XX_SGMII_TBI_TBICTL_CRSTRR		BIT(4)
+#define  GSW1XX_SGMII_TBI_TBICTL_CRSOFF		BIT(5)
+#define GSW1XX_SGMII_TBI_TBISTAT		0x309
+#define  GSW1XX_SGMII_TBI_TBISTAT_LINK		BIT(0)
+#define  GSW1XX_SGMII_TBI_TBISTAT_AN_COMPLETE	BIT(1)
+#define GSW1XX_SGMII_TBI_LPSTAT			0x30a
+#define  GSW1XX_SGMII_TBI_LPSTAT_DUPLEX		BIT(0)
+#define  GSW1XX_SGMII_TBI_LPSTAT_PAUSE_RX	BIT(1)
+#define  GSW1XX_SGMII_TBI_LPSTAT_PAUSE_TX	BIT(2)
+#define  GSW1XX_SGMII_TBI_LPSTAT_SPEED		GENMASK(6, 5)
+#define   GSW1XX_SGMII_TBI_LPSTAT_SPEED_10	0
+#define   GSW1XX_SGMII_TBI_LPSTAT_SPEED_100	1
+#define   GSW1XX_SGMII_TBI_LPSTAT_SPEED_1000	2
+#define   GSW1XX_SGMII_TBI_LPSTAT_SPEED_NOSGMII	3
+#define GSW1XX_SGMII_PHY_D			0x100
+#define GSW1XX_SGMII_PHY_A			0x101
+#define GSW1XX_SGMII_PHY_C			0x102
+#define  GSW1XX_SGMII_PHY_STATUS		BIT(0)
+#define  GSW1XX_SGMII_PHY_READ			BIT(4)
+#define  GSW1XX_SGMII_PHY_WRITE			BIT(8)
+#define  GSW1XX_SGMII_PHY_RESET_N		BIT(12)
+#define GSW1XX_SGMII_PCS_RXB_CTL		0x401
+#define  GSW1XX_SGMII_PCS_RXB_CTL_INIT_RX_RXB	BIT(1)
+#define GSW1XX_SGMII_PCS_TXB_CTL		0x404
+#define  GSW1XX_SGMII_PCS_TXB_CTL_INIT_TX_TXB	BIT(1)
+
+#define GSW1XX_SGMII_PHY_RX0_CFG2		0x004
+#define  GSW1XX_SGMII_PHY_RX0_CFG2_EQ		GENMASK(2, 0)
+#define   GSW1XX_SGMII_PHY_RX0_CFG2_EQ_DEF	2
+#define  GSW1XX_SGMII_PHY_RX0_CFG2_INVERT	BIT(3)
+#define  GSW1XX_SGMII_PHY_RX0_CFG2_LOS_EN	BIT(4)
+#define  GSW1XX_SGMII_PHY_RX0_CFG2_TERM_EN	BIT(5)
+#define  GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT	GENMASK(12, 6)
+#define   GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT_DEF	20
+
+/* GSW1XX PDI Registers */
+#define GSW1XX_SWITCH_BASE			0xe000
+
+/* GSW1XX MII Registers */
+#define GSW1XX_RGMII_BASE			0xf100
+
+/* GSW1XX GPIO Registers */
+#define GSW1XX_GPIO_BASE			0xf300
+#define GPIO_ALTSEL0				0x83
+#define GPIO_ALTSEL0_EXTPHY_MUX_VAL		0x03c3
+#define GPIO_ALTSEL1				0x84
+#define GPIO_ALTSEL1_EXTPHY_MUX_VAL		0x003f
+
+/* MDIO bus controller */
+#define GSW1XX_MMDIO_BASE			0xf400
+
+/* generic IC registers */
+#define GSW1XX_SHELL_BASE			0xfa00
+#define  GSW1XX_SHELL_RST_REQ			0x01
+#define   GSW1XX_RST_REQ_SGMII_SHELL		BIT(5)
+/* RGMII PAD Slew Control Register */
+#define  GSW1XX_SHELL_RGMII_SLEW_CFG		0x78
+#define   RGMII_SLEW_CFG_RX_2_5_V		BIT(4)
+#define   RGMII_SLEW_CFG_TX_2_5_V		BIT(5)
+
+/* SGMII clock related settings */
+#define GSW1XX_CLK_BASE				0xf900
+#define  GSW1XX_CLK_NCO_CTRL			0x68
+#define   GSW1XX_SGMII_HSP_MASK			GENMASK(3, 2)
+#define   GSW1XX_SGMII_SEL			BIT(1)
+#define   GSW1XX_SGMII_1G			0x0
+#define   GSW1XX_SGMII_2G5			0xc
+#define   GSW1XX_SGMII_1G_NCO1			0x0
+#define   GSW1XX_SGMII_2G5_NCO2			0x2
+
 /* Maximum packet size supported by the switch. In theory this should be 10240,
  * but long packets currently cause lock-ups with an MTU of over 2526. Medium
  * packets are sometimes dropped (e.g. TCP over 2477, UDP over 2516-2519, ICMP
@@ -254,6 +362,7 @@ struct gswip_hw_info {
 				 struct phylink_config *config);
 	struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config,
 					      phy_interface_t interface);
+	bool supports_2500m;
 };
 
 struct gswip_gphy_fw {
Signature · 1 line
2.50.1
#1 lore raw

Hi Daniel,

Quoted 13 lines · Daniel Golle

Add registers needed for MaxLinear GSW1xx family of dedicated switch ICs connected via MDIO or SPI.

---
 drivers/net/dsa/lantiq_gswip.h | 109 +++++++++++++++++++++++++++++++++

 1 file changed, 109 insertions(+)
drivers/net/dsa/lantiq_gswip.h +0 -0
index fd898991180d..e8914480d59e 100644
@@ -224,6 +224,114 @@
Quoted 4 lines


 #define XRX200_GPHY_FW_ALIGN (16 * 1024)

+#define GSW1XX_PORTS 6

a tricky questions for you ;-)

There are scarce references to Port 6 across GSW145 datasheet, the 7th port. One could also enable/disable it (bit P6) in GSWIP_CFG (0xF400).

Yes, it's sold as 6-port switch, but the question is, shall the port 6 be disabled to save power and avoid unnecessary EMI?

Signature · 3 lines
Alexander Sverdlin
Siemens AG
www.siemens.com
#2 lore raw

Hi Alenxander,

thank you for the thorough review of the RFC series!

Quoted 11 lines · Alexander
Quoted 2 lines · Daniel Golle

[...]
+#define GSW1XX_PORTS 6

a tricky questions for you ;-)

There are scarce references to Port 6 across GSW145 datasheet, the 7th port. One could also enable/disable it (bit P6) in GSWIP_CFG (0xF400).

Yes, it's sold as 6-port switch, but the question is, shall the port 6 be disabled to save power and avoid unnecessary EMI?

I understood that port 6 can be used for packet injection or monitoring over the management interface (MDIO or SPI). For a moment I thought it'd be cool to implement a (very slow) Ethernet netdev allowing to use that feature in Linux -- but it would be very very slow and also useless on systems which anyway got either port 4 or 5 connected to the host as CPU port. I guess it is intended for basic managed switches which come with a simple microcontroller connected to the GSW1xx chip: ~1 MBit/s "Ethernet-over-MDIO" or (slightly faster due to duplex) "Ethernet-over-SPI" can be fast enough to serve a simple Web UI, Telnet, SSH, or respond to SNMP or LLDP, for example.
I wonder if that port also supports the DSA special tag (insertion and egress)...

Anyway, fantasies aside, at least for now it does make sense to disable it, though I wouldn't expect significant power saving or reduced EMI from that (but you never know...)