board: stm32mp1: remove board.c
PATCH 1/1 board: stm32mp1: remove board.c
Remove the file board/st/stm32mp1/board.c which is not more compiled since commit 156732cc8939 ("board: stm32mp1: move the function board_debug_uart_init in spl.c")
---
Issue when initial patch [1] was applied:
board/st/stm32mp1/board.c deleted +0 -0
[1] http://patchwork.ozlabs.org/project/uboot/patch/20200525101949.15944-10-patrick.delaunay at st.com/
board/st/stm32mp1/board.c | 36 ------------------------------------ 1 file changed, 36 deletions(-) delete mode 100644 board/st/stm32mp1/board.c
board/st/stm32mp1/board.c deleted +0 -36
@@ -1,36 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause -/* -* Copyright (C) 2018, STMicroelectronics - All Rights Reserved -*/ - -#include <common.h> -#include <asm/io.h> -#include <linux/bitops.h> -#include <linux/delay.h> - -#ifdef CONFIG_DEBUG_UART_BOARD_INIT -void board_debug_uart_init (void ) -{ -#if (CONFIG_DEBUG_UART_BASE ==STM32_UART4_BASE ) - -#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00) -#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28) - -/* UART4 clock enable */ -setbits_le32 (RCC_MP_APB1ENSETR ,BIT (16 )); - -#define GPIOG_BASE 0x50008000 -/* GPIOG clock enable */ -writel (BIT (6 ),RCC_MP_AHB4ENSETR ); -/* GPIO configuration for EVAL board -* => Uart4 TX = G11 -*/ -writel (0xffbfffff ,GPIOG_BASE +0x00 ); -writel (0x00006000 ,GPIOG_BASE +0x24 ); -#else - -#error ("CONFIG_DEBUG_UART_BASE: not supported value") - -#endif -} -#endif
Signature · 1 line
2.17.1
PATCH 1/1 board: stm32mp1: remove board.c
Hi Patrick
Quoted 51 lines · Patrick Delaunay
Remove the file
board/st/stm32mp1/board.cwhich is not more compiled since commit156732cc8939("board: stm32mp1: move the functionboard_debug_uart_initinspl.c")Fixes 156732cc8939 ("board: stm32mp1: move the function board_debug_uart_init in spl.c")Signed-off-by Patrick Delaunay <[email protected]>---
Issue when initial patch [1] was applied:board/st/stm32mp1/board.c deleted +0
-0[1] http://patchwork.ozlabs.org/project/uboot/patch/20200525101949.15944-10-patrick.delaunay at st.com/
board/st/stm32mp1/board.c | 36 ------------------------------------ 1 file changed, 36 deletions(-) delete mode 100644 board/st/stm32mp1/board.cboard/st/stm32mp1/board.c deleted +0
-26@@ -1,36 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause -/* -* Copyright (C) 2018, STMicroelectronics - All Rights Reserved -*/ - -#include <common.h> -#include <asm/io.h> -#include <linux/bitops.h> -#include <linux/delay.h> - -#ifdef CONFIG_DEBUG_UART_BOARD_INIT -void board_debug_uart_init (void ) -{ -#if (CONFIG_DEBUG_UART_BASE ==STM32_UART4_BASE ) - -#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00) -#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28) - -/* UART4 clock enable */ -setbits_le32 (RCC_MP_APB1ENSETR ,BIT (16 )); - -#define GPIOG_BASE 0x50008000 -/* GPIOG clock enable */ -writel (BIT (6 ),RCC_MP_AHB4ENSETR ); -/* GPIO configuration for EVAL board -* => Uart4 TX = G11
board/st/stm32mp1/board.c line 36
Quoted 10 lines
board/st/stm32mp1/board.c deleted +0
-10-*/ -writel (0xffbfffff ,GPIOG_BASE +0x00 ); -writel (0x00006000 ,GPIOG_BASE +0x24 ); -#else - -#error ("CONFIG_DEBUG_UART_BASE: not supported value") - -#endif -} -#endif
Thanks
Patrice
PATCH 1/1 board: stm32mp1: remove board.c
This patch doesn't apply correctly and the sha1 was not the correct one. Nevertheless i update it and applied it on u-boot-stm/master
Thanks
patrice
Quoted 73 lines · Patrice CHOTARD
Hi Patrick
Quoted 51 lines · Patrick Delaunay
Remove the file
board/st/stm32mp1/board.cwhich is not more compiled since commit156732cc8939("board: stm32mp1: move the functionboard_debug_uart_initinspl.c")Fixes 156732cc8939 ("board: stm32mp1: move the function board_debug_uart_init in spl.c")Signed-off-by Patrick Delaunay <[email protected]>---
Issue when initial patch [1] was applied:board/st/stm32mp1/board.c deleted +0
-0[1] http://patchwork.ozlabs.org/project/uboot/patch/20200525101949.15944-10-patrick.delaunay at st.com/
board/st/stm32mp1/board.c | 36 ------------------------------------ 1 file changed, 36 deletions(-) delete mode 100644 board/st/stm32mp1/board.cboard/st/stm32mp1/board.c deleted +0
-26@@ -1,36 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause -/* -* Copyright (C) 2018, STMicroelectronics - All Rights Reserved -*/ - -#include <common.h> -#include <asm/io.h> -#include <linux/bitops.h> -#include <linux/delay.h> - -#ifdef CONFIG_DEBUG_UART_BOARD_INIT -void board_debug_uart_init (void ) -{ -#if (CONFIG_DEBUG_UART_BASE ==STM32_UART4_BASE ) - -#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00) -#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28) - -/* UART4 clock enable */ -setbits_le32 (RCC_MP_APB1ENSETR ,BIT (16 )); - -#define GPIOG_BASE 0x50008000 -/* GPIOG clock enable */ -writel (BIT (6 ),RCC_MP_AHB4ENSETR ); -/* GPIO configuration for EVAL board -* => Uart4 TX = G11 board/st/stm32mp1/board.c line 36
Quoted 10 lines
board/st/stm32mp1/board.c deleted +0
-10-*/ -writel (0xffbfffff ,GPIOG_BASE +0x00 ); -writel (0x00006000 ,GPIOG_BASE +0x24 ); -#else - -#error ("CONFIG_DEBUG_UART_BASE: not supported value") - -#endif -} -#endif Reviewed-by Patrice Chotard <[email protected]>Thanks
Patrice
_______________________________________________
Uboot-stm32 mailing list
Uboot-stm32 at st-md-mailman.stormreply.com
https://st-md-mailman.stormreply.com/mailman/listinfo/uboot-stm32