Add Additional Boards and Features to RGxx3
cover Add Additional Boards and Features to RGxx3
From: Chris Morgan <[email protected]>
The RGxx3 is a pseudo-device for U-Boot that works for every Anbernic RGxx3 series device on the market. Add support for another series of very similar devices from Powkiddy.
Chris Morgan (3):
board: rockchip: Refactor panel auto-detect code
board: rockchip: Add Maskrom Mode for Anbernic RGxx3
board: rockchip: Add support for RGB30 and RK2023 to RGxx3
board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 195 ++++++++++++++++----- 1 file changed, 154 insertions(+), 41 deletions(-)
Signature · 1 line
2.34.1
PATCH 1/3 board: rockchip: Refactor panel auto-detect code
From: Chris Morgan <[email protected]>
Make the inability to detect a panel using the auto detection code not fail the entire boot process. This means that if the panel ID cannot be read we don't set an environment variable for the panel, and if an environment variable for the panel is not set we don't attempt to update the compatible string. Changes to the code also ensure that when there are multiple compatible strings required for the panel we use them both, which solves some issues that will pop up soon for the Linux driver.
--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 115 +++++++++++++-------- 1 file changed, 74 insertions(+), 41 deletions(-)
board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +74 -41
@@ -40,6 +40,7 @@ struct rg3xx_model {const char *board;const char *board_name;const char *fdtfile; +const bool detect_panel; };enum rgxx3_device_id {
@@ -54,52 +55,67 @@ enum rgxx3_device_id {static const struct rg3xx_model rg3xx_model_details[] = { [RG353M ] = { -517 ,/* Observed average from device */ -"rk3566-anbernic-rg353m" , -"RG353M" , -DTB_DIR "rk3566-anbernic-rg353p.dtb" ,/* Identical devices */ + .adc_value =517 ,/* Observed average from device */ + .board ="rk3566-anbernic-rg353m" , + .board_name ="RG353M" , +/* Device is identical to RG353P. */ + .fdtfile =DTB_DIR "rk3566-anbernic-rg353p.dtb" , + .detect_panel =1 , }, [RG353P ] = { -860 ,/* Documented value of 860 */ -"rk3566-anbernic-rg353p" , -"RG353P" , -DTB_DIR "rk3566-anbernic-rg353p.dtb" , + .adc_value =860 ,/* Documented value of 860 */ + .board ="rk3566-anbernic-rg353p" , + .board_name ="RG353P" , + .fdtfile =DTB_DIR "rk3566-anbernic-rg353p.dtb" , + .detect_panel =1 , }, [RG353V ] = { -695 ,/* Observed average from device */ -"rk3566-anbernic-rg353v" , -"RG353V" , -DTB_DIR "rk3566-anbernic-rg353v.dtb" , + .adc_value =695 ,/* Observed average from device */ + .board ="rk3566-anbernic-rg353v" , + .board_name ="RG353V" , + .fdtfile =DTB_DIR "rk3566-anbernic-rg353v.dtb" , + .detect_panel =1 , }, [RG503 ] = { -1023 ,/* Observed average from device */ -"rk3566-anbernic-rg503" , -"RG503" , -DTB_DIR "rk3566-anbernic-rg503.dtb" , + .adc_value =1023 ,/* Observed average from device */ + .board ="rk3566-anbernic-rg503" , + .board_name ="RG503" , + .fdtfile =DTB_DIR "rk3566-anbernic-rg503.dtb" , + .detect_panel =0 , },/* Devices with duplicate ADC value */ [RG353PS ] = { -860 ,/* Observed average from device */ -"rk3566-anbernic-rg353ps" , -"RG353PS" , -DTB_DIR "rk3566-anbernic-rg353ps.dtb" , + .adc_value =860 ,/* Observed average from device */ + .board ="rk3566-anbernic-rg353ps" , + .board_name ="RG353PS" , + .fdtfile =DTB_DIR "rk3566-anbernic-rg353ps.dtb" , + .detect_panel =1 , }, [RG353VS ] = { -695 ,/* Gathered from second hand information */ -"rk3566-anbernic-rg353vs" , -"RG353VS" , -DTB_DIR "rk3566-anbernic-rg353vs.dtb" , + .adc_value =695 ,/* Gathered from second hand information */ + .board ="rk3566-anbernic-rg353vs" , + .board_name ="RG353VS" , + .fdtfile =DTB_DIR "rk3566-anbernic-rg353vs.dtb" , + .detect_panel =1 , }, };struct rg353_panel {const u16 id; -const char *panel_compat; +const char *panel_compat[2 ]; };static const struct rg353_panel rg353_panel_details[] = { - { .id =0x3052 , .panel_compat ="newvision,nv3051d" }, - { .id =0x3821 , .panel_compat ="anbernic,rg353v-panel-v2" }, + { + .id =0x3052 , + .panel_compat[0 ] ="anbernic,rg353p-panel" , + .panel_compat[1 ] ="newvision,nv3051d" , + }, + { + .id =0x3821 , + .panel_compat[0 ] ="anbernic,rg353v-panel-v2" , + .panel_compat[1 ] =NULL , + }, };/*
@@ -298,11 +314,10 @@ int rgxx3_detect_display(void)if (!panel) {printf ("Unable to identify panel_id %x\n" , (panel_id[0 ] <<8 ) | panel_id[1 ]); -env_set ("panel" ,"unknown" );return -EINVAL ; } -env_set ("panel" , panel->panel_compat); +env_set ("panel" , panel->panel_compat[0 ]);return 0 ; }
@@ -367,13 +382,14 @@ int rgxx3_detect_device(void) rg3xx_model_details[board_id].board_name);env_set ("fdtfile" , rg3xx_model_details[board_id].fdtfile); -/* Detect the panel type for any device that isn't a 503. */ -if (board_id ==RG503 ) +/* Skip panel detection for when it is not needed. */ +if (!rg3xx_model_details[board_id].detect_panel)return 0 ; +/* Warn but don't fail for errors in auto-detection of the panel. */ ret =rgxx3_detect_display ();if (ret) -return ret; +printf ("Failed to detect panel type\n" );return 0 ; }
@@ -400,7 +416,8 @@ int rk_board_late_init(void)int ft_board_setup (void *blob,struct bd_info *bd) { -int node, ret; +const struct rg353_panel *panel =NULL ; +int node, ret, i;char *env;/* No fixups necessary for the RG503 */
@@ -414,6 +431,12 @@ int ft_board_setup(void *blob, struct bd_info *bd) rg3xx_model_details[RG353M ].board_name, sizeof(rg3xx_model_details[RG353M].board_name)); + env =env_get ("panel" ); +if (!env) { +printf ("Can't get panel env\n" ); +return 0 ; + } +/* * Check if the environment variable doesn't equal the panel. * If it doesn't, update the devicetree to the correct panel.
@@ -424,12 +447,6 @@ int ft_board_setup(void *blob, struct bd_info *bd)return -ENODEV ; } - env =env_get ("panel" ); -if (!env) { -printf ("Can't get panel env\n" ); -return -ENODEV ; - } - ret =fdt_node_check_compatible (blob, node, env);if (ret <0 )return -ENODEV ;
@@ -438,8 +455,24 @@ int ft_board_setup(void *blob, struct bd_info *bd)if (!ret)return 0 ; -do_fixup_by_path_string (blob,"/dsi@fe060000/panel@0" , -"compatible" , env); +/* Panels don't match, search by first compatible value. */ +for (i =0 ; i <ARRAY_SIZE (rg353_panel_details); i++) { +if (!strcmp (env, rg353_panel_details[i].panel_compat[0 ])) { + panel = &rg353_panel_details[i]; +break ; + } + } + +if (!panel) { +printf ("Unable to identify panel by compat string\n" ); +return -ENODEV ; + } + +/* Set the compatible with the auto-detected values */ +fdt_setprop_string (blob, node,"compatible" , panel->panel_compat[0 ]); +if (panel->panel_compat[1 ]) +fdt_appendprop_string (blob, node,"compatible" , + panel->panel_compat[1 ]);return 0 ; }
Signature · 1 line
2.34.1
PATCH 2/3 board: rockchip: Add Maskrom Mode for Anbernic RGxx3
In reply to Chris MorganFrom: Chris Morgan <[email protected]>
Add support for users to enter maskrom mode by holding the function button when they power up the device.
Since the device has soldered eMMC and sometimes does not expose a clk pin on the mainboard there is a small chance that a user who flashes a bad bootloader may not be able to recover if the headers themselves are valid. As a result this check is done during spl_early_init() to ensure that it runs as early as possible, and it does so by directly manipulating the ADC hardware in lieu of loading the ADC driver.
Ideally, once we have an open source TPL stage we can move this to the TPL stage, so it will run even earlier.
--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+)
board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +64 -0
@@ -6,12 +6,14 @@#include <abuf.h> #include <adc.h> #include <asm/io.h> +#include <command.h> #include <display.h> #include <dm.h> #include <dm/lists.h> #include <env.h> #include <fdt_support.h> #include <linux/delay.h> +#include <linux/iopoll.h> #include <mipi_dsi.h> #include <mmc.h> #include <panel.h>
@@ -20,6 +22,8 @@#include <stdlib.h> #include <video_bridge.h> +#define BOOT_BROM_DOWNLOAD 0xef08a53c +#define GPIO0_BASE 0xfdd60000#define GPIO4_BASE 0xfe770000#define GPIO_SWPORT_DR_L 0x0000
@@ -33,6 +37,14 @@#define GPIO_WRITEMASK (bits) ((bits) << 16) +#define SARADC_BASE 0xfe720000 +#define SARADC_DATA 0x0000 +#define SARADC_STAS 0x0004 +#define SARADC_ADC_STATUS BIT(0) +#define SARADC_CTRL 0x0008 +#define SARADC_INPUT_SRC_MSK 0x7 +#define SARADC_POWER_CTRL BIT(3) +#define DTB_DIR "rockchip/"struct rg3xx_model {
@@ -118,12 +130,64 @@ static const struct rg353_panel rg353_panel_details[] = { }, }; +/* +* The device has internal eMMC, and while some devices have an exposed +* clk pin you can ground to force a bypass not all devices do. As a +* result it may be possible for some devices to become a perma-brick +* if a corrupted TPL or SPL stage with a valid header is flashed to +* the internal eMMC. Add functionality to read ADC channel 0 (the func +* button) as early as possible in the boot process to provide some +* protection against this. If we ever get an open TPL stage, we should +* consider moving this function there. +*/ +void read_func_button (void ) +{ +int ret; +u32 reg; + +/* Turn off SARADC to reset it. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* Enable channel 0 and power on SARADC. */ +writel (((0 &SARADC_INPUT_SRC_MSK ) |SARADC_POWER_CTRL ), + (SARADC_BASE +SARADC_CTRL )); + +/* +* Wait for data to be ready. Use timeout of 20000us from +* rockchip_saradc driver. +*/ + ret =readl_poll_timeout ((SARADC_BASE +SARADC_STAS ), reg, + !(reg &SARADC_ADC_STATUS ),20000 ); +if (ret) { +printf ("ADC Timeout" ); +return ; + } + +/* Read the data from the SARADC. */ + reg =readl ((SARADC_BASE +SARADC_DATA )); + +/* Turn the SARADC back off so it's ready to be used again. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* +* If the value is less than 30 the button is being pressed. +* Reset the device back into Rockchip download mode. +*/ +if (reg <=30 ) { +printf ("download key pressed, entering download mode..." ); +writel (BOOT_BROM_DOWNLOAD ,CONFIG_ROCKCHIP_BOOT_MODE_REG ); +do_reset (NULL ,0 ,0 ,NULL ); + } +}; +/* * Start LED very early so user knows device is on. Set color * to red. */ void spl_board_init (void ) { +read_func_button (); +/* Set GPIO0_C5, GPIO0_C6, and GPIO0_C7 to output. */ writel(GPIO_WRITEMASK(GPIO_C7 | GPIO_C6 | GPIO_C5) | \ (GPIO_C7 | GPIO_C6 | GPIO_C5),
Signature · 1 line
2.34.1
Re: [PATCH 2/3] board: rockchip: Add Maskrom Mode for Anbernic RGxx3
Hi Chris,
Quoted 7 lines · Chris Morgan
From: Chris Morgan <[email protected]>
Add support for users to enter maskrom mode by holding the function button when they power up the device.
Since the device has soldered eMMC and sometimes does not expose a clk pin on the mainboard
This board already available, so does this clk pin available?
Not only clk, other cmd/data pin is also OK to make the soc get into maskrom mode.
Quoted 5 lines
there is a small chance that a user who flashes a
bad bootloader may not be able to recover if the headers themselves are valid. As a result this check is done duringspl_early_init()to ensure that it runs as early as possible, and it does so by directly manipulating the ADC hardware in lieu of loading the ADC driver.
This key seems like a "recovery" adc key instead of "maskrom" key, right?
I think we don't need to add this patch if the hardware does not really have a "maskrom" key.
Basically the "maskrom" key should not depends on any software.
Thanks,
- Kever
Quoted 117 lines
Ideally, once we have an open source TPL stage we can move this to the TPL stage, so it will run even earlier.
Signed-off-by Chris Morgan <[email protected]>--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+)board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +64
-0@@ -6,12 +6,14 @@#include <abuf.h> #include <adc.h> #include <asm/io.h> +#include <command.h> #include <display.h> #include <dm.h> #include <dm/lists.h> #include <env.h> #include <fdt_support.h> #include <linux/delay.h> +#include <linux/iopoll.h> #include <mipi_dsi.h> #include <mmc.h> #include <panel.h> @@ -20,6 +22,8 @@#include <stdlib.h> #include <video_bridge.h> +#define BOOT_BROM_DOWNLOAD 0xef08a53c +#define GPIO0_BASE 0xfdd60000#define GPIO4_BASE 0xfe770000#define GPIO_SWPORT_DR_L 0x0000@@ -33,6 +37,14 @@#define GPIO_WRITEMASK (bits) ((bits) << 16) +#define SARADC_BASE 0xfe720000 +#define SARADC_DATA 0x0000 +#define SARADC_STAS 0x0004 +#define SARADC_ADC_STATUS BIT(0) +#define SARADC_CTRL 0x0008 +#define SARADC_INPUT_SRC_MSK 0x7 +#define SARADC_POWER_CTRL BIT(3) +#define DTB_DIR "rockchip/"struct rg3xx_model {@@ -118,12 +130,64 @@ static const struct rg353_panel rg353_panel_details[] = { }, }; +/* +* The device has internal eMMC, and while some devices have an exposed +* clk pin you can ground to force a bypass not all devices do. As a +* result it may be possible for some devices to become a perma-brick +* if a corrupted TPL or SPL stage with a valid header is flashed to +* the internal eMMC. Add functionality to read ADC channel 0 (the func +* button) as early as possible in the boot process to provide some +* protection against this. If we ever get an open TPL stage, we should +* consider moving this function there. +*/ +void read_func_button (void ) +{ +int ret; +u32 reg; + +/* Turn off SARADC to reset it. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* Enable channel 0 and power on SARADC. */ +writel (((0 &SARADC_INPUT_SRC_MSK ) |SARADC_POWER_CTRL ), + (SARADC_BASE +SARADC_CTRL )); + +/* +* Wait for data to be ready. Use timeout of 20000us from +* rockchip_saradc driver. +*/ + ret =readl_poll_timeout ((SARADC_BASE +SARADC_STAS ), reg, + !(reg &SARADC_ADC_STATUS ),20000 ); +if (ret) { +printf ("ADC Timeout" ); +return ; + } + +/* Read the data from the SARADC. */ + reg =readl ((SARADC_BASE +SARADC_DATA )); + +/* Turn the SARADC back off so it's ready to be used again. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* +* If the value is less than 30 the button is being pressed. +* Reset the device back into Rockchip download mode. +*/ +if (reg <=30 ) { +printf ("download key pressed, entering download mode..." ); +writel (BOOT_BROM_DOWNLOAD ,CONFIG_ROCKCHIP_BOOT_MODE_REG ); +do_reset (NULL ,0 ,0 ,NULL ); + } +}; +/* * Start LED very early so user knows device is on. Set color * to red. */ void spl_board_init (void ) { +read_func_button (); +/* Set GPIO0_C5, GPIO0_C6, and GPIO0_C7 to output. */ writel(GPIO_WRITEMASK(GPIO_C7 | GPIO_C6 | GPIO_C5) | \ (GPIO_C7 | GPIO_C6 | GPIO_C5),
Re: [PATCH 2/3] board: rockchip: Add Maskrom Mode for Anbernic RGxx3
Quoted 8 lines · Kever Yang
Hi Chris,
Quoted 5 lines · Chris Morgan
From: Chris Morgan <[email protected]>
Add support for users to enter maskrom mode by holding the function button when they power up the device.
Quoted 7 lines
Quoted 2 lines
Since the device has soldered eMMC and sometimes does not expose a clk pin on the mainboard
This board already available, so does this clk pin available?
Not only clk, other cmd/data pin is also OK to make the soc get into maskrom mode.
No, as near as I can tell some boards (such as the 353P and 353V) don't expose a clk, cmd, or data pin. The 353M does expose a clk pin though.
Quoted 7 lines
Quoted 6 lines
there is a small chance that a user who flashes a
bad bootloader may not be able to recover if the headers themselves are valid. As a result this check is done duringspl_early_init()to ensure that it runs as early as possible, and it does so by directly manipulating the ADC hardware in lieu of loading the ADC driver.
Quoted 6 lines
This key seems like a "recovery" adc key instead of "maskrom" key, right?
I think we don't need to add this patch if the hardware does not really have a "maskrom" key.
Basically the "maskrom" key should not depends on any software.
Okay, so should I rename it as a "recovery" key? Basically it's just a button hooked up to ADC channel 0. I'm trying to make as simple a failsafe as possible, because for the boards without the clk/cmd pads I want to make it easy to debrick in the event of something like a bad U-Boot stage or a bad A-TF stage.
Thank you.
Quoted 118 lines
Thanks,
- Kever
Quoted 112 lines
Ideally, once we have an open source TPL stage we can move this to the TPL stage, so it will run even earlier.
Signed-off-by Chris Morgan <[email protected]>--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+)board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +64
-0@@ -6,12 +6,14 @@#include <abuf.h> #include <adc.h> #include <asm/io.h> +#include <command.h> #include <display.h> #include <dm.h> #include <dm/lists.h> #include <env.h> #include <fdt_support.h> #include <linux/delay.h> +#include <linux/iopoll.h> #include <mipi_dsi.h> #include <mmc.h> #include <panel.h> @@ -20,6 +22,8 @@#include <stdlib.h> #include <video_bridge.h> +#define BOOT_BROM_DOWNLOAD 0xef08a53c +#define GPIO0_BASE 0xfdd60000#define GPIO4_BASE 0xfe770000#define GPIO_SWPORT_DR_L 0x0000@@ -33,6 +37,14 @@#define GPIO_WRITEMASK (bits) ((bits) << 16) +#define SARADC_BASE 0xfe720000 +#define SARADC_DATA 0x0000 +#define SARADC_STAS 0x0004 +#define SARADC_ADC_STATUS BIT(0) +#define SARADC_CTRL 0x0008 +#define SARADC_INPUT_SRC_MSK 0x7 +#define SARADC_POWER_CTRL BIT(3) +#define DTB_DIR "rockchip/"struct rg3xx_model {@@ -118,12 +130,64 @@ static const struct rg353_panel rg353_panel_details[] = { }, }; +/* +* The device has internal eMMC, and while some devices have an exposed +* clk pin you can ground to force a bypass not all devices do. As a +* result it may be possible for some devices to become a perma-brick +* if a corrupted TPL or SPL stage with a valid header is flashed to +* the internal eMMC. Add functionality to read ADC channel 0 (the func +* button) as early as possible in the boot process to provide some +* protection against this. If we ever get an open TPL stage, we should +* consider moving this function there. +*/ +void read_func_button (void ) +{ +int ret; +u32 reg; + +/* Turn off SARADC to reset it. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* Enable channel 0 and power on SARADC. */ +writel (((0 &SARADC_INPUT_SRC_MSK ) |SARADC_POWER_CTRL ), + (SARADC_BASE +SARADC_CTRL )); + +/* +* Wait for data to be ready. Use timeout of 20000us from +* rockchip_saradc driver. +*/ + ret =readl_poll_timeout ((SARADC_BASE +SARADC_STAS ), reg, + !(reg &SARADC_ADC_STATUS ),20000 ); +if (ret) { +printf ("ADC Timeout" ); +return ; + } + +/* Read the data from the SARADC. */ + reg =readl ((SARADC_BASE +SARADC_DATA )); + +/* Turn the SARADC back off so it's ready to be used again. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* +* If the value is less than 30 the button is being pressed. +* Reset the device back into Rockchip download mode. +*/ +if (reg <=30 ) { +printf ("download key pressed, entering download mode..." ); +writel (BOOT_BROM_DOWNLOAD ,CONFIG_ROCKCHIP_BOOT_MODE_REG ); +do_reset (NULL ,0 ,0 ,NULL ); + } +}; +/* * Start LED very early so user knows device is on. Set color * to red. */ void spl_board_init (void ) { +read_func_button (); +/* Set GPIO0_C5, GPIO0_C6, and GPIO0_C7 to output. */ writel(GPIO_WRITEMASK(GPIO_C7 | GPIO_C6 | GPIO_C5) | \ (GPIO_C7 | GPIO_C6 | GPIO_C5),
Re: [PATCH 2/3] board: rockchip: Add Maskrom Mode for Anbernic RGxx3
Hi Chris,
Quoted 32 lines · Chris Morgan
Quoted 8 lines · Kever Yang
Hi Chris,
Quoted 5 lines · Chris Morgan
From: Chris Morgan <[email protected]>
Add support for users to enter maskrom mode by holding the function button when they power up the device.
Quoted 7 lines
Quoted 2 lines
Since the device has soldered eMMC and sometimes does not expose a clk pin on the mainboard
This board already available, so does this clk pin available?
Not only clk, other cmd/data pin is also OK to make the soc get into maskrom mode.
No, as near as I can tell some boards (such as the 353P and 353V) don't expose a clk, cmd, or data pin. The 353M does expose a clk pin though.
Quoted 12 lines
Quoted 6 lines
there is a small chance that a user who flashes a
bad bootloader may not be able to recover if the headers themselves are valid. As a result this check is done duringspl_early_init()to ensure that it runs as early as possible, and it does so by directly manipulating the ADC hardware in lieu of loading the ADC driver.This key seems like a "recovery" adc key instead of "maskrom" key, right?
I think we don't need to add this patch if the hardware does not really have a "maskrom" key.
Quoted 7 lines
Quoted 1 line
Basically the "maskrom" key should not depends on any software.
Okay, so should I rename it as a "recovery" key? Basically it's just a button hooked up to ADC channel 0. I'm trying to make as simple a failsafe as possible, because for the boards without the clk/cmd pads I want to make it easy to debrick in the event of something like a bad U-Boot stage or a bad A-TF stage.
Isn't this very similar to what arch/arm/mach-rockchip/boot_mode.c and rockchip_dnl_key_pressed() already does, or is supposed to do?
Maybe this existing code can be changed/fixed to work earlier in SPL and possible also read recovery button information from DT or Kconfig to work with more rockchip boards?
Would be nice if a hang/panic in SPL make rk devices reset into maskrom usb mode. Maybe even the watchdog can be of some use here.
Btw, you could probably also enable CONFIG_SPL_FIT_SIGNATURE for added protection against starting corrupt/bitrot FIT images. To speed up boot after adding a sha256 checksum test, you can use following rfc/patch:
[RFC] rockchip: spl: Enable caches to speed up checksum validation
https://patchwork.ozlabs.org/patch/1802303/
Regards,
Jonas
Quoted 121 lines
Thank you.
Quoted 118 lines
Thanks,
- Kever
Quoted 112 lines
Ideally, once we have an open source TPL stage we can move this to the TPL stage, so it will run even earlier.
Signed-off-by Chris Morgan <[email protected]>--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+)board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +64
-0@@ -6,12 +6,14 @@#include <abuf.h> #include <adc.h> #include <asm/io.h> +#include <command.h> #include <display.h> #include <dm.h> #include <dm/lists.h> #include <env.h> #include <fdt_support.h> #include <linux/delay.h> +#include <linux/iopoll.h> #include <mipi_dsi.h> #include <mmc.h> #include <panel.h> @@ -20,6 +22,8 @@#include <stdlib.h> #include <video_bridge.h> +#define BOOT_BROM_DOWNLOAD 0xef08a53c +#define GPIO0_BASE 0xfdd60000#define GPIO4_BASE 0xfe770000#define GPIO_SWPORT_DR_L 0x0000@@ -33,6 +37,14 @@#define GPIO_WRITEMASK (bits) ((bits) << 16) +#define SARADC_BASE 0xfe720000 +#define SARADC_DATA 0x0000 +#define SARADC_STAS 0x0004 +#define SARADC_ADC_STATUS BIT(0) +#define SARADC_CTRL 0x0008 +#define SARADC_INPUT_SRC_MSK 0x7 +#define SARADC_POWER_CTRL BIT(3) +#define DTB_DIR "rockchip/"struct rg3xx_model {@@ -118,12 +130,64 @@ static const struct rg353_panel rg353_panel_details[] = { }, }; +/* +* The device has internal eMMC, and while some devices have an exposed +* clk pin you can ground to force a bypass not all devices do. As a +* result it may be possible for some devices to become a perma-brick +* if a corrupted TPL or SPL stage with a valid header is flashed to +* the internal eMMC. Add functionality to read ADC channel 0 (the func +* button) as early as possible in the boot process to provide some +* protection against this. If we ever get an open TPL stage, we should +* consider moving this function there. +*/ +void read_func_button (void ) +{ +int ret; +u32 reg; + +/* Turn off SARADC to reset it. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* Enable channel 0 and power on SARADC. */ +writel (((0 &SARADC_INPUT_SRC_MSK ) |SARADC_POWER_CTRL ), + (SARADC_BASE +SARADC_CTRL )); + +/* +* Wait for data to be ready. Use timeout of 20000us from +* rockchip_saradc driver. +*/ + ret =readl_poll_timeout ((SARADC_BASE +SARADC_STAS ), reg, + !(reg &SARADC_ADC_STATUS ),20000 ); +if (ret) { +printf ("ADC Timeout" ); +return ; + } + +/* Read the data from the SARADC. */ + reg =readl ((SARADC_BASE +SARADC_DATA )); + +/* Turn the SARADC back off so it's ready to be used again. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* +* If the value is less than 30 the button is being pressed. +* Reset the device back into Rockchip download mode. +*/ +if (reg <=30 ) { +printf ("download key pressed, entering download mode..." ); +writel (BOOT_BROM_DOWNLOAD ,CONFIG_ROCKCHIP_BOOT_MODE_REG ); +do_reset (NULL ,0 ,0 ,NULL ); + } +}; +/* * Start LED very early so user knows device is on. Set color * to red. */ void spl_board_init (void ) { +read_func_button (); +/* Set GPIO0_C5, GPIO0_C6, and GPIO0_C7 to output. */ writel(GPIO_WRITEMASK(GPIO_C7 | GPIO_C6 | GPIO_C5) | \ (GPIO_C7 | GPIO_C6 | GPIO_C5),
Re: [PATCH 2/3] board: rockchip: Add Maskrom Mode for Anbernic RGxx3
Quoted 57 lines · Jonas Karlman
Hi Chris,
Quoted 32 lines · Chris Morgan
Quoted 8 lines · Kever Yang
Hi Chris,
Quoted 5 lines · Chris Morgan
From: Chris Morgan <[email protected]>
Add support for users to enter maskrom mode by holding the function button when they power up the device.
Quoted 7 lines
Quoted 2 lines
Since the device has soldered eMMC and sometimes does not expose a clk pin on the mainboard
This board already available, so does this clk pin available?
Not only clk, other cmd/data pin is also OK to make the soc get into maskrom mode.
No, as near as I can tell some boards (such as the 353P and 353V) don't expose a clk, cmd, or data pin. The 353M does expose a clk pin though.
Quoted 12 lines
Quoted 6 lines
there is a small chance that a user who flashes a
bad bootloader may not be able to recover if the headers themselves are valid. As a result this check is done duringspl_early_init()to ensure that it runs as early as possible, and it does so by directly manipulating the ADC hardware in lieu of loading the ADC driver.This key seems like a "recovery" adc key instead of "maskrom" key, right?
I think we don't need to add this patch if the hardware does not really have a "maskrom" key.
Quoted 7 lines
Quoted 1 line
Basically the "maskrom" key should not depends on any software.
Okay, so should I rename it as a "recovery" key? Basically it's just a button hooked up to ADC channel 0. I'm trying to make as simple a failsafe as possible, because for the boards without the clk/cmd pads I want to make it easy to debrick in the event of something like a bad U-Boot stage or a bad A-TF stage.
Isn't this very similar to what
arch/arm/mach-rockchip/boot_mode.candrockchip_dnl_key_pressed()already does, or is supposed to do?Maybe this existing code can be changed/fixed to work earlier in SPL and possible also read recovery button information from DT or
Kconfigto work with more rockchip boards?Would be nice if a hang/panic in SPL make rk devices reset into maskrom usb mode. Maybe even the watchdog can be of some use here.
Btw, you could probably also enable
CONFIG_SPL_FIT_SIGNATUREfor added protection against starting corrupt/bitrot FIT images. To speed up boot after adding a sha256 checksum test, you can use following rfc/patch:
Quoted 5 lines
[RFC] rockchip: spl: Enable caches to speed up checksum validation
https://patchwork.ozlabs.org/patch/1802303/Regards,
Jonas
Thank you, yes I will look into that. That said even if we detect a corrupt SPL stage we're still stuck unless we add the additional reset stuff like you mention.
Yes, this is more or less identical to the rockchip_dnl_key_pressed() function with 2 distinct differences; one this doesn't require the ADC driver since we're manipulating the controller directly (this makes it easier to support in SPL or maybe even one day TPL), and two the existing function has hard-coded checks for channel 1 whereas the board here uses channel 0 for the function button. The comments for the existing function suggest that it's meant to be "generic" and boards are welcome to override with their own function, which is what I'm doing though at an earlier stage in the boot process.
Thank you,
Chris
Quoted 123 lines
Quoted 122 lines
Thank you.
Quoted 118 lines
Thanks,
- Kever
Quoted 112 lines
Ideally, once we have an open source TPL stage we can move this to the TPL stage, so it will run even earlier.
Signed-off-by Chris Morgan <[email protected]>--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+)board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +64
-0@@ -6,12 +6,14 @@#include <abuf.h> #include <adc.h> #include <asm/io.h> +#include <command.h> #include <display.h> #include <dm.h> #include <dm/lists.h> #include <env.h> #include <fdt_support.h> #include <linux/delay.h> +#include <linux/iopoll.h> #include <mipi_dsi.h> #include <mmc.h> #include <panel.h> @@ -20,6 +22,8 @@#include <stdlib.h> #include <video_bridge.h> +#define BOOT_BROM_DOWNLOAD 0xef08a53c +#define GPIO0_BASE 0xfdd60000#define GPIO4_BASE 0xfe770000#define GPIO_SWPORT_DR_L 0x0000@@ -33,6 +37,14 @@#define GPIO_WRITEMASK (bits) ((bits) << 16) +#define SARADC_BASE 0xfe720000 +#define SARADC_DATA 0x0000 +#define SARADC_STAS 0x0004 +#define SARADC_ADC_STATUS BIT(0) +#define SARADC_CTRL 0x0008 +#define SARADC_INPUT_SRC_MSK 0x7 +#define SARADC_POWER_CTRL BIT(3) +#define DTB_DIR "rockchip/"struct rg3xx_model {@@ -118,12 +130,64 @@ static const struct rg353_panel rg353_panel_details[] = { }, }; +/* +* The device has internal eMMC, and while some devices have an exposed +* clk pin you can ground to force a bypass not all devices do. As a +* result it may be possible for some devices to become a perma-brick +* if a corrupted TPL or SPL stage with a valid header is flashed to +* the internal eMMC. Add functionality to read ADC channel 0 (the func +* button) as early as possible in the boot process to provide some +* protection against this. If we ever get an open TPL stage, we should +* consider moving this function there. +*/ +void read_func_button (void ) +{ +int ret; +u32 reg; + +/* Turn off SARADC to reset it. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* Enable channel 0 and power on SARADC. */ +writel (((0 &SARADC_INPUT_SRC_MSK ) |SARADC_POWER_CTRL ), + (SARADC_BASE +SARADC_CTRL )); + +/* +* Wait for data to be ready. Use timeout of 20000us from +* rockchip_saradc driver. +*/ + ret =readl_poll_timeout ((SARADC_BASE +SARADC_STAS ), reg, + !(reg &SARADC_ADC_STATUS ),20000 ); +if (ret) { +printf ("ADC Timeout" ); +return ; + } + +/* Read the data from the SARADC. */ + reg =readl ((SARADC_BASE +SARADC_DATA )); + +/* Turn the SARADC back off so it's ready to be used again. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* +* If the value is less than 30 the button is being pressed. +* Reset the device back into Rockchip download mode. +*/ +if (reg <=30 ) { +printf ("download key pressed, entering download mode..." ); +writel (BOOT_BROM_DOWNLOAD ,CONFIG_ROCKCHIP_BOOT_MODE_REG ); +do_reset (NULL ,0 ,0 ,NULL ); + } +}; +/* * Start LED very early so user knows device is on. Set color * to red. */ void spl_board_init (void ) { +read_func_button (); +/* Set GPIO0_C5, GPIO0_C6, and GPIO0_C7 to output. */ writel(GPIO_WRITEMASK(GPIO_C7 | GPIO_C6 | GPIO_C5) | \ (GPIO_C7 | GPIO_C6 | GPIO_C5),
Re: [PATCH 2/3] board: rockchip: Add Maskrom Mode for Anbernic RGxx3
Quoted 78 lines · Chris Morgan
Quoted 57 lines · Jonas Karlman
Hi Chris,
Quoted 32 lines · Chris Morgan
Quoted 8 lines · Kever Yang
Hi Chris,
Quoted 5 lines · Chris Morgan
From: Chris Morgan <[email protected]>
Add support for users to enter maskrom mode by holding the function button when they power up the device.
Quoted 7 lines
Quoted 2 lines
Since the device has soldered eMMC and sometimes does not expose a clk pin on the mainboard
This board already available, so does this clk pin available?
Not only clk, other cmd/data pin is also OK to make the soc get into maskrom mode.
No, as near as I can tell some boards (such as the 353P and 353V) don't expose a clk, cmd, or data pin. The 353M does expose a clk pin though.
Quoted 12 lines
Quoted 6 lines
there is a small chance that a user who flashes a
bad bootloader may not be able to recover if the headers themselves are valid. As a result this check is done duringspl_early_init()to ensure that it runs as early as possible, and it does so by directly manipulating the ADC hardware in lieu of loading the ADC driver.This key seems like a "recovery" adc key instead of "maskrom" key, right?
I think we don't need to add this patch if the hardware does not really have a "maskrom" key.
Quoted 7 lines
Quoted 1 line
Basically the "maskrom" key should not depends on any software.
Okay, so should I rename it as a "recovery" key? Basically it's just a button hooked up to ADC channel 0. I'm trying to make as simple a failsafe as possible, because for the boards without the clk/cmd pads I want to make it easy to debrick in the event of something like a bad U-Boot stage or a bad A-TF stage.
Isn't this very similar to what
arch/arm/mach-rockchip/boot_mode.candrockchip_dnl_key_pressed()already does, or is supposed to do?Maybe this existing code can be changed/fixed to work earlier in SPL and possible also read recovery button information from DT or
Kconfigto work with more rockchip boards?Would be nice if a hang/panic in SPL make rk devices reset into maskrom usb mode. Maybe even the watchdog can be of some use here.
Btw, you could probably also enable
CONFIG_SPL_FIT_SIGNATUREfor added protection against starting corrupt/bitrot FIT images. To speed up boot after adding a sha256 checksum test, you can use following rfc/patch:Quoted 5 lines
[RFC] rockchip: spl: Enable caches to speed up checksum validation
https://patchwork.ozlabs.org/patch/1802303/Regards,
JonasThank you, yes I will look into that. That said even if we detect a corrupt SPL stage we're still stuck unless we add the additional reset stuff like you mention.
Yes, this is more or less identical to the
rockchip_dnl_key_pressed()function with 2 distinct differences; one this doesn't require the ADC driver since we're manipulating the controller directly (this makes it easier to support in SPL or maybe even one day TPL), and two the existing function has hard-coded checks for channel 1 whereas the board here uses channel 0 for the function button. The comments for the existing function suggest that it's meant to be "generic" and boards are welcome to override with their own function, which is what I'm doing though at an earlier stage in the boot process.
Quoted 2 lines
Thank you,
Chris
Just wanted to dig this one back up. If I refer to this as "recovery" instead of "maskrom", are we okay to go?
Thank you.
Quoted 124 lines
Quoted 124 lines
Quoted 123 lines
Thank you.
Quoted 118 lines
Thanks,
- Kever
Quoted 112 lines
Ideally, once we have an open source TPL stage we can move this to the TPL stage, so it will run even earlier.
Signed-off-by Chris Morgan <[email protected]>--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 64 ++++++++++++++++++++++ 1 file changed, 64 insertions(+)board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +64
-0@@ -6,12 +6,14 @@#include <abuf.h> #include <adc.h> #include <asm/io.h> +#include <command.h> #include <display.h> #include <dm.h> #include <dm/lists.h> #include <env.h> #include <fdt_support.h> #include <linux/delay.h> +#include <linux/iopoll.h> #include <mipi_dsi.h> #include <mmc.h> #include <panel.h> @@ -20,6 +22,8 @@#include <stdlib.h> #include <video_bridge.h> +#define BOOT_BROM_DOWNLOAD 0xef08a53c +#define GPIO0_BASE 0xfdd60000#define GPIO4_BASE 0xfe770000#define GPIO_SWPORT_DR_L 0x0000@@ -33,6 +37,14 @@#define GPIO_WRITEMASK (bits) ((bits) << 16) +#define SARADC_BASE 0xfe720000 +#define SARADC_DATA 0x0000 +#define SARADC_STAS 0x0004 +#define SARADC_ADC_STATUS BIT(0) +#define SARADC_CTRL 0x0008 +#define SARADC_INPUT_SRC_MSK 0x7 +#define SARADC_POWER_CTRL BIT(3) +#define DTB_DIR "rockchip/"struct rg3xx_model {@@ -118,12 +130,64 @@ static const struct rg353_panel rg353_panel_details[] = { }, }; +/* +* The device has internal eMMC, and while some devices have an exposed +* clk pin you can ground to force a bypass not all devices do. As a +* result it may be possible for some devices to become a perma-brick +* if a corrupted TPL or SPL stage with a valid header is flashed to +* the internal eMMC. Add functionality to read ADC channel 0 (the func +* button) as early as possible in the boot process to provide some +* protection against this. If we ever get an open TPL stage, we should +* consider moving this function there. +*/ +void read_func_button (void ) +{ +int ret; +u32 reg; + +/* Turn off SARADC to reset it. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* Enable channel 0 and power on SARADC. */ +writel (((0 &SARADC_INPUT_SRC_MSK ) |SARADC_POWER_CTRL ), + (SARADC_BASE +SARADC_CTRL )); + +/* +* Wait for data to be ready. Use timeout of 20000us from +* rockchip_saradc driver. +*/ + ret =readl_poll_timeout ((SARADC_BASE +SARADC_STAS ), reg, + !(reg &SARADC_ADC_STATUS ),20000 ); +if (ret) { +printf ("ADC Timeout" ); +return ; + } + +/* Read the data from the SARADC. */ + reg =readl ((SARADC_BASE +SARADC_DATA )); + +/* Turn the SARADC back off so it's ready to be used again. */ +writel (0 , (SARADC_BASE +SARADC_CTRL )); + +/* +* If the value is less than 30 the button is being pressed. +* Reset the device back into Rockchip download mode. +*/ +if (reg <=30 ) { +printf ("download key pressed, entering download mode..." ); +writel (BOOT_BROM_DOWNLOAD ,CONFIG_ROCKCHIP_BOOT_MODE_REG ); +do_reset (NULL ,0 ,0 ,NULL ); + } +}; +/* * Start LED very early so user knows device is on. Set color * to red. */ void spl_board_init (void ) { +read_func_button (); +/* Set GPIO0_C5, GPIO0_C6, and GPIO0_C7 to output. */ writel(GPIO_WRITEMASK(GPIO_C7 | GPIO_C6 | GPIO_C5) | \ (GPIO_C7 | GPIO_C6 | GPIO_C5),
PATCH 3/3 board: rockchip: Add support for RGB30 and RK2023 to RGxx3
In reply to Chris MorganFrom: Chris Morgan <[email protected]>
Add support for the Powkiddy RK2023 and RGB30 to the Anbernic RGxx3. While these devices are manufactured by Powkiddy instead of Anbernic, the hardware is so similar they can all use the same bootloader.
--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +16 -0
@@ -60,6 +60,8 @@ enum rgxx3_device_id {RG353P ,RG353V ,RG503 , +RGB30 , +RK2023 ,/* Devices with duplicate ADC value */ RG353PS , RG353VS,
@@ -95,6 +97,20 @@ static const struct rg3xx_model rg3xx_model_details[] = { .fdtfile = DTB_DIR "rk3566-anbernic-rg503.dtb", .detect_panel = 0, }, + [RGB30] = { + .adc_value = 383, /* Gathered from second hand information */ + .board = "rk3566-powkiddy-rgb30", + .board_name = "RGB30", + .fdtfile = DTB_DIR "rk3566-powkiddy-rgb30.dtb", + .detect_panel = 0, + }, + [RK2023] = { + .adc_value = 635, /* Observed average from device */ + .board = "rk3566-powkiddy-rk2023", + .board_name = "RK2023", + .fdtfile = DTB_DIR "rk3566-powkiddy-rk2023.dtb", + .detect_panel = 0, + },/* Devices with duplicate ADC value */ [RG353PS] = { .adc_value = 860, /* Observed average from device */
Signature · 1 line
2.34.1
Re: [PATCH 3/3] board: rockchip: Add support for RGB30 and RK2023 to RGxx3
Quoted 7 lines · Chris Morgan
From: Chris Morgan <[email protected]>
Add support for the Powkiddy RK2023 and RGB30 to the Anbernic RGxx3. While these devices are manufactured by Powkiddy instead of Anbernic, the hardware is so similar they can all use the same bootloader.
Signed-off-by Chris Morgan <[email protected]>
Thanks,
- Kever
Quoted 38 lines
--- board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)board/anbernic/rgxx3_rk3566/rgxx3-rk3566.c +16
-0@@ -60,6 +60,8 @@ enum rgxx3_device_id {RG353P ,RG353V ,RG503 , +RGB30 , +RK2023 ,/* Devices with duplicate ADC value */ RG353PS , RG353VS,@@ -95,6 +97,20 @@ static const struct rg3xx_model rg3xx_model_details[] = { .fdtfile = DTB_DIR "rk3566-anbernic-rg503.dtb", .detect_panel = 0, }, + [RGB30] = { + .adc_value = 383, /* Gathered from second hand information */ + .board = "rk3566-powkiddy-rgb30", + .board_name = "RGB30", + .fdtfile = DTB_DIR "rk3566-powkiddy-rgb30.dtb", + .detect_panel = 0, + }, + [RK2023] = { + .adc_value = 635, /* Observed average from device */ + .board = "rk3566-powkiddy-rk2023", + .board_name = "RK2023", + .fdtfile = DTB_DIR "rk3566-powkiddy-rk2023.dtb", + .detect_panel = 0, + },/* Devices with duplicate ADC value */ [RG353PS] = { .adc_value = 860, /* Observed average from device */