Skip to contentSkip to conversation

sunxi: mmc support

PATCH New Ian Campbell 1 participant 1 message Mar 7, 2014

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 7/8 sunxi: mmc support

This adds support for the MMC controller on the Allwinner A20 (sun7i) processor.

---
v5.1: Based on 3f5ff92b1503 "sunxi: add comments to pll1_para array."
- Drop unused CONFIG_MMC1_PG option
- Make comments in mmc_pinmux_setup be consistent (always Function-Pin, not half Pin-Function).

v5: Based on 3f5ff92b1503 "sunxi: add comments to pll1_para array."
- No changes required

v4: Based on d9fe0a1e061e "sunxi: mksunxiboot: remove unnecessary casts."
- Moved pinmux setup from drivers/mmc/sunxi_mmc.c to board/sunxi/board.c
- Use setbits_le32 to manipulate the ahb0 gate.

v3: Based on c89867dca2e9 "sunxi: clocks: clock_get_pll5 prototype and coding style".

v2: Based on u-boot-sunxi.git#sunxi d9aa5dd3d15c "sunxi: mmc:
checkpatch whitespace fixes" with v2014.04-rc2 merged in:
- use proper gpio interfaces, removing awkward casts and some magic numbers.
- remove magic numbers
- other cleanups

v1: Based on u-boot-sunxi.git#sunxi commit d854c4de2f57 "arm: Handle .gnu.hash section in ldscripts" vs v2014.01.

mmc: drop debug

---
 arch/arm/include/asm/arch-sunxi/mmc.h | 124 +++++++++
 board/sunxi/board.c                   |  63 +++++
 drivers/mmc/Makefile                  |   1 +
 drivers/mmc/sunxi_mmc.c               | 503 ++++++++++++++++++++++++++++++++++
 include/configs/sunxi-common.h        |  11 +
 5 files changed, 702 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-sunxi/mmc.h
 create mode 100644 drivers/mmc/sunxi_mmc.c
arch/arm/include/asm/arch-sunxi/mmc.h new file +124 -0
new file mode 100644
index 0000000..53196e3
@@ -0,0 +1,124 @@
+/*
+ * (C) Copyright 2007-2011
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ * Aaron <[email protected]>
+ *
+ * MMC register definition for allwinner sunxi platform.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _SUNXI_MMC_H
+#define _SUNXI_MMC_H
+
+#include <linux/types.h>
+
+struct sunxi_mmc {
+	u32 gctrl;		/* 0x00 global control */
+	u32 clkcr;		/* 0x04 clock control */
+	u32 timeout;		/* 0x08 time out */
+	u32 width;		/* 0x0c bus width */
+	u32 blksz;		/* 0x10 block size */
+	u32 bytecnt;		/* 0x14 byte count */
+	u32 cmd;		/* 0x18 command */
+	u32 arg;		/* 0x1c argument */
+	u32 resp0;		/* 0x20 response 0 */
+	u32 resp1;		/* 0x24 response 1 */
+	u32 resp2;		/* 0x28 response 2 */
+	u32 resp3;		/* 0x2c response 3 */
+	u32 imask;		/* 0x30 interrupt mask */
+	u32 mint;		/* 0x34 masked interrupt status */
+	u32 rint;		/* 0x38 raw interrupt status */
+	u32 status;		/* 0x3c status */
+	u32 ftrglevel;		/* 0x40 FIFO threshold watermark*/
+	u32 funcsel;		/* 0x44 function select */
+	u32 cbcr;		/* 0x48 CIU byte count */
+	u32 bbcr;		/* 0x4c BIU byte count */
+	u32 dbgc;		/* 0x50 debug enable */
+	u32 res0[11];
+	u32 dmac;		/* 0x80 internal DMA control */
+	u32 dlba;		/* 0x84 internal DMA descr list base address */
+	u32 idst;		/* 0x88 internal DMA status */
+	u32 idie;		/* 0x8c internal DMA interrupt enable */
+	u32 chda;		/* 0x90 */
+	u32 cbda;		/* 0x94 */
+	u32 res1[26];
+	u32 fifo;		/* 0x100 FIFO access address */
+};
+
+#define SUNXI_MMC_CLK_POWERSAVE		(0x1 << 17)
+#define SUNXI_MMC_CLK_ENABLE		(0x1 << 16)
+#define SUNXI_MMC_CLK_DIVIDER_MASK	(0xff)
+
+#define SUNXI_MMC_GCTRL_SOFT_RESET	(0x1 << 0)
+#define SUNXI_MMC_GCTRL_FIFO_RESET	(0x1 << 1)
+#define SUNXI_MMC_GCTRL_DMA_RESET	(0x1 << 2)
+#define SUNXI_MMC_GCTRL_RESET		(SUNXI_MMC_GCTRL_SOFT_RESET|\
+					 SUNXI_MMC_GCTRL_FIFO_RESET|\
+					 SUNXI_MMC_GCTRL_DMA_RESET)
+#define SUNXI_MMC_GCTRL_DMA_ENABLE	(0x1 << 5)
+#define SUNXI_MMC_GCTRL_ACCESS_BY_AHB   (0x1 << 31)
+
+#define SUNXI_MMC_CMD_RESP_EXPIRE	(0x1 << 6)
+#define SUNXI_MMC_CMD_LONG_RESPONSE	(0x1 << 7)
+#define SUNXI_MMC_CMD_CHK_RESPONSE_CRC	(0x1 << 8)
+#define SUNXI_MMC_CMD_DATA_EXPIRE	(0x1 << 9)
+#define SUNXI_MMC_CMD_WRITE		(0x1 << 10)
+#define SUNXI_MMC_CMD_AUTO_STOP		(0x1 << 12)
+#define SUNXI_MMC_CMD_WAIT_PRE_OVER	(0x1 << 13)
+#define SUNXI_MMC_CMD_SEND_INIT_SEQ	(0x1 << 15)
+#define SUNXI_MMC_CMD_UPCLK_ONLY	(0x1 << 21)
+#define SUNXI_MMC_CMD_START		(0x1 << 31)
+
+#define SUNXI_MMC_RINT_RESP_ERROR		(0x1 << 1)
+#define SUNXI_MMC_RINT_COMMAND_DONE		(0x1 << 2)
+#define SUNXI_MMC_RINT_DATA_OVER		(0x1 << 3)
+#define SUNXI_MMC_RINT_TX_DATA_REQUEST		(0x1 << 4)
+#define SUNXI_MMC_RINT_RX_DATA_REQUEST		(0x1 << 5)
+#define SUNXI_MMC_RINT_RESP_CRC_ERROR		(0x1 << 6)
+#define SUNXI_MMC_RINT_DATA_CRC_ERROR		(0x1 << 7)
+#define SUNXI_MMC_RINT_RESP_TIMEOUT		(0x1 << 8)
+#define SUNXI_MMC_RINT_DATA_TIMEOUT		(0x1 << 9)
+#define SUNXI_MMC_RINT_VOLTAGE_CHANGE_DONE	(0x1 << 10)
+#define SUNXI_MMC_RINT_FIFO_RUN_ERROR		(0x1 << 11)
+#define SUNXI_MMC_RINT_HARD_WARE_LOCKED		(0x1 << 12)
+#define SUNXI_MMC_RINT_START_BIT_ERROR		(0x1 << 13)
+#define SUNXI_MMC_RINT_AUTO_COMMAND_DONE	(0x1 << 14)
+#define SUNXI_MMC_RINT_END_BIT_ERROR		(0x1 << 15)
+#define SUNXI_MMC_RINT_SDIO_INTERRUPT		(0x1 << 16)
+#define SUNXI_MMC_RINT_CARD_INSERT		(0x1 << 30)
+#define SUNXI_MMC_RINT_CARD_REMOVE		(0x1 << 31)
+#define SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT      \
+	(SUNXI_MMC_RINT_RESP_ERROR |		\
+	 SUNXI_MMC_RINT_RESP_CRC_ERROR |	\
+	 SUNXI_MMC_RINT_DATA_CRC_ERROR |	\
+	 SUNXI_MMC_RINT_RESP_TIMEOUT |		\
+	 SUNXI_MMC_RINT_DATA_TIMEOUT |		\
+	 SUNXI_MMC_RINT_VOLTAGE_CHANGE_DONE |	\
+	 SUNXI_MMC_RINT_FIFO_RUN_ERROR |	\
+	 SUNXI_MMC_RINT_HARD_WARE_LOCKED |	\
+	 SUNXI_MMC_RINT_START_BIT_ERROR |	\
+	 SUNXI_MMC_RINT_END_BIT_ERROR) /* 0xbfc2 */
+#define SUNXI_MMC_RINT_INTERRUPT_DONE_BIT	\
+	(SUNXI_MMC_RINT_AUTO_COMMAND_DONE |	\
+	 SUNXI_MMC_RINT_DATA_OVER |		\
+	 SUNXI_MMC_RINT_COMMAND_DONE |		\
+	 SUNXI_MMC_RINT_VOLTAGE_CHANGE_DONE)
+
+#define SUNXI_MMC_STATUS_RXWL_FLAG		(0x1 << 0)
+#define SUNXI_MMC_STATUS_TXWL_FLAG		(0x1 << 1)
+#define SUNXI_MMC_STATUS_FIFO_EMPTY		(0x1 << 2)
+#define SUNXI_MMC_STATUS_FIFO_FULL		(0x1 << 3)
+#define SUNXI_MMC_STATUS_CARD_PRESENT		(0x1 << 8)
+#define SUNXI_MMC_STATUS_CARD_DATA_BUSY		(0x1 << 9)
+#define SUNXI_MMC_STATUS_DATA_FSM_BUSY		(0x1 << 10)
+
+#define SUNXI_MMC_IDMAC_RESET		(0x1 << 0)
+#define SUNXI_MMC_IDMAC_FIXBURST	(0x1 << 1)
+#define SUNXI_MMC_IDMAC_ENABLE		(0x1 << 7)
+
+#define SUNXI_MMC_IDIE_TXIRQ		(0x1 << 0)
+#define SUNXI_MMC_IDIE_RXIRQ		(0x1 << 1)
+
+int sunxi_mmc_init(int sdc_no);
+#endif /* _SUNXI_MMC_H */
board/sunxi/board.c +63 -0

75 lines not on this page · raw message

drivers/mmc/Makefile +1 -0
index 931922b..5e67098 100644
@@ -28,6 +28,7 @@ obj-$(CONFIG_SPEAR_SDHCI) += spear_sdhci.o
 obj-$(CONFIG_TEGRA_MMC) += tegra_mmc.o
 obj-$(CONFIG_DWMMC) += dw_mmc.o
 obj-$(CONFIG_EXYNOS_DWMMC) += exynos_dw_mmc.o
+obj-$(CONFIG_MMC_SUNXI) += sunxi_mmc.o
 obj-$(CONFIG_ZYNQ_SDHCI) += zynq_sdhci.o
 obj-$(CONFIG_SOCFPGA_DWMMC) += socfpga_dw_mmc.o
 ifdef CONFIG_SPL_BUILD
drivers/mmc/sunxi_mmc.c new file +503 -0

503 lines not on this page · raw message

include/configs/sunxi-common.h +11 -0
index e844110..4253452 100644
@@ -59,6 +59,16 @@
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_INITRD_TAG
 
+/* mmc config */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_MMC_SUNXI
+#define CONFIG_MMC_SUNXI_SLOT		0
+#define CONFIG_MMC_SUNXI_USE_DMA
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0	/* first detected MMC controller */
+
 /* 4MB of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (4 << 20))
 
@@ -94,6 +104,7 @@
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* 512 KiB */
 #define CONFIG_IDENT_STRING		" Allwinner Technology"
 
+#define CONFIG_ENV_OFFSET		(544 << 10) /* (8 + 24 + 512) KiB */
 #define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
Signature · 1 line
1.9.0