Statistics
Dear Guru
What are the meanings of the statistic fields? For example:
qdisc tbf 8020: rate 256Kbit burst 10Kb lat 190.7ms
Sent 941500 bytes 11288 pkts (dropped 33, overlimits 0) backlog 770b 9p
qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 969153 bytes 11632 pkts (dropped 33, overlimits 22419) backlog 9p
borrowed 0 overactions 0 avgidle 624 undertime 0
What "dropped 33" means? Packets I presume.
"Overlimits 22419"? What this mean? Were all these bytes discarded? Backlog? What is this?
Any1 could point some documentation about statistic fields?
Thanks a lot.
Ethy H. Brito /"\
InterNexo Ltda. \ / CAMPANHA DA FITA ASCII - CONTRA MAIL HTML
+55 (12) 3941-6860 X ASCII RIBBON CAMPAIGN - AGAINST HTML MAIL
S.J.Campos - Brasil / \
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Quoted 7 lines · Ethy H. Brito
Dear Guru
What are the meanings of the statistic fields? For example:
qdisc tbf 8020: rate 256Kbit burst 10Kb lat 190.7ms
Sent 941500 bytes 11288 pkts (dropped 33, overlimits 0)
941500 bytes and 11288 were actually sent, and not dropped. 33 packets were dropped.
Quoted 1 line
backlog 770b 9p
9 packets are waiting to be allowed to be sent, totalling 770 bytes.
Quoted 2 lines
qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 969153 bytes 11632 pkts (dropped 33, overlimits 22419)
22419 times did cbq throttle itself because it was exceeding its rate.
Quoted 2 lines
backlog 9p
borrowed 0 overactions 0 avgidle 624 undertime 0
avgidle is described in the manpages on ds9a.nl/lartc/manpages
Regards,
bert
Signature · 8 lines
http://www.PowerDNS.com Versatile DNS Software & Services http://www.tk the dot in .tk Netherlabs BV / Rent-a-Nerd.nl - Nerd Available - Linux Advanced Routing & Traffic Control: http://ds9a.nl/lartc _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Hi all,
I'm experimenting with HTB and IMQ and I'm wondering if there exists a tool to graph the throughput of traffic through my router.
I now I can setup iptables to count packets and read/reset these with a script , but maybe there is allready something MRTG alike but for shorter periods of measurements.
Thanks alot,
Signature · 14 lines
* Bart Duchesne * R&D Engineer * * Able NV * Leuvensesteenweg 282 - B-3190 Boortmeerbeek - Belgium * Phone: + 32 15 50.44.00 - Fax: + 32 15 50.44.09 * E-Mail: [email protected] * URL: http://www.axsguard.com * -- Security check on this e-mail has been done by aXs GUARD (http://www.axsguard.com)
Quoted 7 lines · Bart Duchesne
Hi all,
I'm experimenting with HTB and IMQ and I'm wondering if there exists a tool to graph the throughput of traffic through my router.
I now I can setup iptables to count packets and read/reset these with a script , but maybe there is allready something MRTG alike but for shorter periods of measurements.
Try with 'monitor*' at www.docum.org Stef Coene's website about Traffic Control.
Quoted 20 lines
Thanks alot,
Signature · 15 lines
* Bart Duchesne * R&D Engineer * * Able NV * Leuvensesteenweg 282 - B-3190 Boortmeerbeek - Belgium * Phone: + 32 15 50.44.00 - Fax: + 32 15 50.44.09 * E-Mail: [email protected] * URL: http://www.axsguard.com * -- Security check on this e-mail has been done by aXs GUARD (http://www.axsguard.com)
Signature · 10 lines
-- Daniel Ortiz [email protected] ILIMIT Comunicacions Departament Sistemes http://www.ilimit.es Tel: (+34) 93 733 33 75 Fax: (+34) 93 733 32 43
: I'm experimenting with HTB and IMQ and I'm wondering if there exists a : tool to graph the throughput of traffic through my router.
: I now I can setup iptables to count packets and read/reset these with a : script , but maybe there is allready something MRTG alike but for : shorter periods of measurements.
See Stef's rrdtool-based tools [1] or if you need something more like real-time stats, the Java-based stuff [2], or even his perl tools [3].
-Martin
[1] http://www.docum.org/stef.coene/qos/gui/
[2] http://www.docum.org/stef.coene/qos/java/
[3] http://www.docum.org/stef.coene/qos/monitor/
Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 7 lines · Bart Duchesne
Hi all,
I'm experimenting with HTB and IMQ and I'm wondering if there exists a tool to graph the throughput of traffic through my router.
I now I can setup iptables to count packets and read/reset these with a script , but maybe there is allready something MRTG alike but for shorter periods of measurements.
You might find my snmprtg useful for this, but you will need to be able to query it using SNMP. It can run on most platforms too. Its still very young, but quite usable. Currently the Poll Interval, and the number of minutes to display is hard coded (5 secs, 10 mins respectively), but should be easily changed.
http://nzgeeks.org/cameron/progs/snmprtg.php
Runs on anything with Perl/Tk and the SNMP module. (Developed on Linux, tested with Windows NT and ActiveState Perl)
Signature · 7 lines
Cameron Kerr Email: [email protected] Website: http://nzgeeks.org/cameron/ _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Helle everybody,
I am finishing a computer science degree and I would like to know how you use qos on Linux.
Please take a few seconds to answer my questions
I would like to know :
- what type of qdisc you use
- if it is only for tests or for a "real" use (what use)
- how much qos box do you use
- do you use anything else (Cisco, Unix ...)
I don't know if it is better that you answer to me or to the list, so do as you want. Anyway i will send the result to the list.
Thanks in advance
Emmanuel
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hello, Emmanuel,
Straight to the question:
1. Personally I'm using mostly HTB.
2. Yes, it is in real use - that way I'm controlling traffic in the ISP I'm working in.
3. I didnt get this question. If you're asking about the HW parameters - PIII/1Ghz. If you're asking about the quantity of QOS boxen I'm using - 5 of them, 4 GNU/Linux and one FreeBSD.
4. Yes, I'm using Cisco policers, but not for smth serious. Besides I'm using FreeBSD altq with CBQ as a shaper (cause that's what it is).
On Thu, 4 Sep 2003 22:56:02 +0200
"Emmanuel SIMON" <[email protected]> wrote:
: Helle everybody,
:
: I am finishing a computer science degree and I would like to know how you : use qos on Linux.
:
: Please take a few seconds to answer my questions
:
: I would like to know :
: - what type of qdisc you use : - if it is only for tests or for a "real" use (what use) : - how much qos box do you use : - do you use anything else (Cisco, Unix ...)
:
: I don't know if it is better that you answer to me or to the list, so do as : you want. Anyway i will send the result to the list.
:
: Thanks in advance
: Emmanuel
Signature · 7 lines
Със здраве, Никола _____________________________________________________________ "Engineering does not require science. Science helps a lot but people built perfectly good brick walls long before they knew why cement works." -Alan Cox
allready 2 answers, thank you
the 3rd question don't seem clear :
- I am not asking about the HW parameters, but about the quantity of QOS
boxen you are using
thx for the 2 first and please go on
Quoted 27 lines
-----Message d'origine-----
De : [email protected]
[mailto:[email protected]]De
la part de Emmanuel SIMON
Envoyé : jeudi 4 septembre 2003 22:56
À : 'LARTC'
Objet : [LARTC] StatisticsHelle everybody,
I am finishing a computer science degree and I would like to know how you
use qos on Linux.Please take a few seconds to answer my questions
I would like to know :
- what type of qdisc you use
- if it is only for tests or for a "real" use (what use)
- how much qos box do you use
- do you use anything else (Cisco, Unix ...)I don't know if it is better that you answer to me or to the list, so do as
you want. Anyway i will send the result to the list.
Quoted 7 lines
Thanks in advance
Emmanuel_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/